David Brownell [Sun, 4 Apr 2010 08:28:50 +0000 (01:28 -0700)]
Restore deleted '!' character
I'm not sure what caused this significant character to get deleted.
it may be related to intermittent Editor or terminal flakes I've
been seeing lately (sigh). This fix is trivial.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
David Brownell [Sun, 4 Apr 2010 07:42:05 +0000 (00:42 -0700)]
target: are we running algorithm code?
Fixing one bug can easily uncover another .... in this case,
making sure that we properly invalidate some cached NOR state when
resuming arbitrary target code turned up an issue when the code
wasn't quite arbitrary (and we couldn't know that, but some parts
of OpenOCD assumed the cache would not be invalidated.
Specifically: some flash drivers (like CFI) update that state in loops
with downloaded algorithms, thus invalidating the state as it's probed.
+ Add a new target state flag, to record whether the target is
running downloaded algorithm code.
+ Use that flag to add a special case: "trust" downloaded algorithms
not to corrupt that cached state, bypassing cache invalidation.
Also update some of the documentation to stipulate that this flavor of
trustworthiness is now *required* ... not just a fortuitous acident.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
David Brownell [Sun, 4 Apr 2010 07:38:39 +0000 (00:38 -0700)]
simplify and unconfuse target_run_algorithm()
For some reason there are *two* schemes for interposing logic into
the run_algorithm() code path... One is a standard procedural wapper
around the target method invocation.
the other (superfluous) one hacked the method table by splicing
a second procedural wrapper into the method table. Remove it:
* Rename its slightly-more-featureful wrapper so it becomes
the standard procedural wrapper, leaving its added logic
(where it should have been in the first place.
Also add a paranoia check, to report targets that don't
support algorithms without traversing a NULL pointer, and
tweak its code structure a bit so it's easier to modify.
* Get rid of the superfluous/conusing method table hacks.
This is a net simplification, making it simpler to analyse what's
going on, and then interpose logic . ... by ensuring there's only one
natural place for it to live.
------------
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Mike Dunn [Sun, 28 Mar 2010 19:48:32 +0000 (15:48 -0400)]
xscale: fix trace buffer functionality when resuming from a breakpoint
Problem: halt at a breakpoint, enable trace buffer ('xscale trace_buffer enable
fill'), then resume. Wait for debug exception when trace buffer fills (if not
sooner due to another breakpoint, vector catch, etc). Instead, never halts.
When halted explicitly from OpenOCD and trace buffer dumped, it contains only
one entry; a branch to the address of the original breakpoint. If the above
steps are repeated, except that the breakpoint is removed before resuming, the
trace buffer fills and the debug exception is generated, as expected.
Cause: related to how a breakpoint is stepped over on resume. The breakpoint is
temporarily removed, and a hardware breakpoint is set on the next instruction
that will execute. xscale_debug_entry() is called when that breakpoint hits.
This function checks if the trace buffer is enabled, and if so reads the trace
buffer from the target and then disables the trace (unless multiple trace
buffers are specified by the user when trace is enabled). Thus you only trace
one instruction before it is disabled.
Solution: kind of a hack on top of a hack, but it's simple. Anything better
would involve some refactoring. This has been tested and trace now works as
intended, except that the very first instruction is not part of the trace when
resuming from a breakpoint.
TODO: still many issues with trace: doesn't work during single-stepping (trace
buffer is flushed each step), 'xscale analyze_trace' works only marginally for
a trace captured in 'fill' mode, and not at all for a trace captured in 'wrap'
mode.
David Brownell [Sat, 27 Mar 2010 17:07:13 +0000 (10:07 -0700)]
jtag/tcl.c cleanup -- split out "adapter.c"
Clean up the jtag/tcl.c file, which was one of the biggest and
messiest ones in that directory. Do it by splitting out all the
generic adapter commands to a separate "adapter.c" file (leaving
the "tcl.c" file holding only JTAG utilities).
Also rename the little-used "jtag interface" to "adapter_name", which
should have been at least re-categorized earlier (it's not jtag-only).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Antonio Borneo [Fri, 26 Mar 2010 07:17:46 +0000 (15:17 +0800)]
TCL scripts: update to current "flash bank" syntax
While "flash bank" syntax has been changed long ago,
several tcl script are still not fully update.
Fix following cases related with "cfi" driver:
- syntax error: the mandatory <name> parameter is missing
- warning: the <target> parameter is a number, instead of
the target name
- the comment line above the command does not report
actual syntax
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Øyvind Harboe [Thu, 4 Mar 2010 18:58:42 +0000 (19:58 +0100)]
zy1000: dev tool
first cut peek/poke over tcp/ip, used for debug/research
purposes only. Long term JTAG over TCP/IP might be an
offshoot. The performance is usable for development/testing
purposes.
Øyvind Harboe [Thu, 25 Mar 2010 12:06:23 +0000 (13:06 +0100)]
target: fix poll off
I don't know when "poll off" broke, but "poll off" didn't
stop background polling of target. The polling status flag
simply wasn't checked in the handle_target timer callback.
All target polling(including power/reset state) is now stopped
upon "poll off".
Mike Dunn [Sat, 20 Mar 2010 14:53:47 +0000 (10:53 -0400)]
fix software breakpoints on xscale
This patch fixes xscale software breakpoints by cleaning the dcache and
invalidating the icache after the bkpt instruction is inserted or removed. The
icache operation is necessary in order to flush the fetch buffers, even if the
icache is disabled (see section 4.2.7 of the xscale core developer's manual).
The dcache is presumed to be enabled; no harm done if not. The dcache is also
invalidated after cleaning in order to safeguard against a future load of
invalid data, in the event that cache_clean_address points to memory that is
valid and in use.
Also corrected a confusing typo I noticed in a comment.
TODO (or not TODO...?): the xscale's 2K "mini dcache" is not cleaned. This
cache is not used unless the 'X' bit in the page table entry is set. This is a
proprietary xscale extension to the ARM architecture. If a target's OS or
executive makes use of this for memory regions holding code, the breakpoint
problem will persist. Flushing the mini dcache requires that 2K of valid
cacheable memory (mapped with 'X' bit set) be designated by the user for this
purpose. The debug handler that gets downloaded to the target will also need to
be extended.
David Brownell [Mon, 22 Mar 2010 05:49:23 +0000 (22:49 -0700)]
ft2232 init mess cleanup
In the ft2232 driver, initialization for many layouts punts to a routine
called usbjtag_init(), instead of a routine specific to each layout.
That routine is a mess built around a "what type layout am I" core.
That's a bad design ... in this case, especially so, since it bypasses
the layout-specific dispatch which was just done, and obfuscates the
initialization which is at least somewhat generic, instead of being
specific to the "usbjtag" layout.
Split and document out the generic parts of usbjtag_init(), and make
the rest of those layouts have layout-specific init methods. Also,
rename usbjtag_reset() ... that also was not specific to the "usbjtag"
layout, and thus contributed to the previous code structure confusion.
(Eventually, all layout-specific code (and method tables) should probably
live in files specific to each layout. These changes will facilitate
those and other cleanups to this driver.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Mike Dunn [Fri, 19 Mar 2010 04:34:13 +0000 (21:34 -0700)]
Fix underlying problem with xscale icache and dcache commands
Fix problem with the xscale icache and dcache commands. Both commands were
enabling or disabling the mmu, not the caches
I didn't look any further after my earlier patch fixed the trivial problem
with command argument parsing. Turns out the underlying code was broken.
The resolution is straightforward when you look at the arguments to
xscale_enable_mmu_caches() and xscale_disable_mmu_caches(). I finally
took a deeper look after dumping the cp15 control register (XSCALE_CTRL)
and seeing that the cache bits weren't changing, but the mmu bit was
(which caused all manner of grief, as you can imagine). This has been
tested and works OK now.
David Brownell [Thu, 18 Mar 2010 18:56:17 +0000 (11:56 -0700)]
remove more duplication
Not sure how the original "move code to adi_v5_swd.c" patch left
some code in the "arm_adi_v5.c" file, but a recent patch was only
a partial fix -- it didn't remove all the duplication.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Øyvind Harboe [Tue, 16 Mar 2010 13:13:03 +0000 (14:13 +0100)]
jtag: cut down on usage of unintended modification of global end state
jtag_get/set_end_state() is now deprecated.
There were lots of places in the code where the end state was
unintentionally modified.
The big Q is whether there were any places where the intention
was to modify the end state. 0.5 is a long way off, so we'll
get a fair amount of testing.
Spencer Oliver [Tue, 16 Mar 2010 12:48:53 +0000 (12:48 +0000)]
MIPS: remove ejtag_srst variant
The mips_m4k_assert_reset has now been restructured
so the variant ejtag_srst is not required anymore.
The ejtag software reset will be used if the target does not
have srst connected.
Remove ejtag_srst from docs.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
Øyvind Harboe [Tue, 16 Mar 2010 13:45:07 +0000 (14:45 +0100)]
gdb_server: improved gdb load performance
by ack'ing memory writes immediately and reporting either
at next memory write or stepi/continue time. GDB will then
send off a new packet that is ready by the time the previous
packet has been written to target memory.
On faster adapters this can be as much as 10% improvement.
David Brownell [Tue, 16 Mar 2010 21:12:00 +0000 (14:12 -0700)]
ADIv5 transport support moves to separate files
Unclutter arm_adi_v5.c by moving most transport-specific code
to a transport-specific files adi_v5_{jtag,swd}.c ... it's not
a full cleanup, because of some issues which need to be addressed
as part of SWD support (along with implementing the DAP operations
on top of SWD transport):
- The mess where mem_ap_read_buf_u32() is currently coded to
know about JTAG scan chains, and thus needs rewriting before
it will work with SWD;
- Initialization is still JTAG-specific
Also move JTAG_{DP,ACK}_* constants from adi_v5.h to the JTAG
file; no other code should care about those values.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
richard vegh [Tue, 16 Mar 2010 09:46:41 +0000 (10:46 +0100)]
lpc3180: LPC3180(LPC3250) SLC driver implemented
Until this time only basic SLC functionality exists when you want to use SLC to access external nand flash.
Basic functionality can be selected with command:
lpc3180 select 0 slc
It is anyway very slow to write/read to/from nand flash.
With the new command, SLC speed improved about 20 times, and hardware ECC info also read/written from/to nand flash OOB area:
lpc3180 select 0 slc bulk
Speed improvement achieved by using working are in SRAM of the LPC3250 chip and controlling DMA controller to interact between SRAM and SLC peripheral.
Here are the patches, and if they are ok than take them.
Tested with hitex LPC3250 usb stick.
Bradey Honsinger [Mon, 15 Mar 2010 07:43:41 +0000 (08:43 +0100)]
image loading: fix problem with offsets > 0x80000000
Fixes bug that prevented users from specifying a base address of
0x80000000 or higher in image commands (flash write_image, etm image,
xscale trace_image).
image.base_address is an offset from the start address contained in
the image file (if there is one), or from 0 (for binary files). As a
signed 32-bit int, it couldn't be greater than 0x7fffffff, which is a
problem when trying to write a binary file to flash above that
address. Changing it to a 64-bit long long keeps it as a signed
offset, but allows it to cover the entire 32-bit address space.
David Brownell [Mon, 15 Mar 2010 15:43:16 +0000 (08:43 -0700)]
move "reset_config" out of JTAG command group
The SRST configuration options are not specific to JTAG, so this
command may be needed with non-JTAG debug sessions. Just move
the command to a different group.
(The TRST options are, however, clearly JTAG-specific, but for
compatibility, they're now left alone. The flags they control
could later be disabled in non-JTAG sessions.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
David Brownell [Mon, 15 Mar 2010 15:42:26 +0000 (08:42 -0700)]
rename jtag_nsrst_assert_width as adapter_nsrst_assert_width
Globally rename "jtag_nsrst_assert_width" as "adapter_nsrst_assert_width",
and move it out of the "jtag" command group ... it needs to be used with
non-JTAG transports
Includes a migration aid (in jtag/startup.tcl) so that old user scripts
won't break. That aid should Sunset in about a year.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
David Brownell [Mon, 15 Mar 2010 15:41:30 +0000 (08:41 -0700)]
rename jtag_nsrst_delay as adapter_nsrst_delay
Globally rename "jtag_nsrst_delay" as "adapter_nsrst_delay", and move it
out of the "jtag" command group ... it needs to be used with non-JTAG
transports
Includes a migration aid (in jtag/startup.tcl) so that old user scripts
won't break. That aid should Sunset in about a year.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
David Brownell [Mon, 15 Mar 2010 15:37:43 +0000 (08:37 -0700)]
rename jtag_khz as adapter_khz
Globally rename "jtag_khz" as "adapter_khz", and move it out of the "jtag"
command group ... it needs to be used with non-JTAG transports
Includes a migration aid (in jtag/startup.tcl) so that old user scripts
won't break. That aid should Sunset in about a year. (We may want to
update it to include a nag message too.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Spencer Oliver [Mon, 15 Mar 2010 09:36:46 +0000 (09:36 +0000)]
PIC32MX: update cfg script
The default config script will now dynamically setup the BMX registers
in the reset init script.
This will also work if the user overrides the default working area.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
David Brownell [Sun, 14 Mar 2010 20:10:26 +0000 (13:10 -0700)]
FT2232: lookup and save layout just once
Streamline use of the layout: have the "ft2232_layout" command
look it up and save the result, instead of having a few different
chunks of code looking it up later, and saving just its name (which
is already part of the layout). This
- is cleaner
- reports errors sooner
- facilitates earlier adapter-specific setup
- removes unused "default to "usbjtag" logic
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
simon qian [Thu, 11 Mar 2010 22:11:30 +0000 (14:11 -0800)]
New JTAG driver for Versaloon
This patch greatly simplifies the Versaloon driver:
- reducing the code size from more than 50K to less than 28K
- adding support for IR/DR scan with unlimited size
- using tap_get_tms_path and tap_get_tms_path_len.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
David Brownell [Thu, 11 Mar 2010 17:47:47 +0000 (09:47 -0800)]
split "interface" commands from "jtag" ones
We'll need to be able to work with debug adapter interfaces (drivers)
even when they're not used for JTAG ... for example, while there are
multi-transport drivers which support JTAG *and* several other
transports (or just one more, like SWD) there are also adapters
with more limited goals (and no JTAG support at all).
Start decoupling the two concepts ("debug adapter driver", "jtag")
by having two command groups, which initialize separately.
This will help us support OpenOCD sessions using only non-JTAG
transports, in which JTAG commands should not be registered.
Update docs to mention that the JTAG, SVF, and XSVF commands
won't work without a JTAG transport.
Note that at least commands working with SRST are still inappropriately
coupled to JTAG ... inappropriate because (a) SRST is not part of the
JTAG standard, for all that many platforms (like ARM) expect it; and also
(b) because they're used with non-JTAG debug and programming interfaces,
too. They should perhaps become generic "interface" operations at some
point. (Similarly with the clock rate to be used by a given adapter.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Spencer Oliver [Mon, 8 Mar 2010 22:54:18 +0000 (22:54 +0000)]
PIC32: add flash algorithm support
Add flash algorithm support for the PIC32MX.
Still a few things todo but this dramatically decreases
the programing time, eg. approx programming for 2.5k test file.
- without fastload: 60secs
- with fastload: 45secs
- with fastload and algorithm: 2secs.
Add new devices to supported list.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
David Brownell [Tue, 9 Mar 2010 03:10:05 +0000 (19:10 -0800)]
move a constant table to .rodata section
The table of command registration functions shouldn't be
in writable memory, where stray pointers can clobber it.
Also, it shouldn't be initialized at runtime; that just
consumes needless code space.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Antonio Borneo [Mon, 8 Mar 2010 17:31:27 +0000 (18:31 +0100)]
cfi: simplify and clearify code
At the end I have added comments /* FIXME: to be removed */
There are 3 lines in which my simplification is not complete due to
data dependency with LOG_DEBUG() messages visible in the patch.
Such log_debug has been introduced on Jan 22, 2007 with commit 4fc97d3f2726efa147cfdb0c456eace51550e1e3 during development activity
in this file/procedure.
From my point of view, these logs can be removed, since not part of a
consistent flow of information.
Alternatively, could be borrowed in the new cfi_send_command(), but
this will increase verbosity.
Øyvind Harboe [Mon, 8 Mar 2010 07:32:45 +0000 (08:32 +0100)]
zy1000: embedded ice dcc tweak
How many bits to shift out before/after enabled tap not
in bypass is calculated outside the loop. This is more of
a demonstration of principle and to clarify code than
a performance optimisation as such. Follows up a bit
on the simplification work in jtag interface.
Antonio Borneo [Fri, 5 Mar 2010 16:56:36 +0000 (00:56 +0800)]
CFI: review print of Voltage values
JEDEC standard reports Vpp integer part encoded as 4 bit HEX value.
To print it using decimal digits, %u is required.
Other voltage values are coded as BCD, so %x is appropriate.
Code already prints one nibble at a time, so no need for field width
and precision in format string.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com> Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
David Brownell [Sat, 6 Mar 2010 05:09:03 +0000 (21:09 -0800)]
doc: not all debug adapters are "dongles"
Talk more about "debug adapters" instead of only "dongles". Not all
adapters are discrete widgets; some are integrated onto boards. If
we only talk about "dongles" we rule out many valid setups, and help
confuse some users (who may be using Dongle-free environments).
Also start bringing out the point that JTAG isn't the only transport
protocol, even though OpenOCD historically presumes "all is JTAG".
(Not all debug adapters are JTAG adapters, or JTAG-only adapters.)
Plus a few minor fixes (spelling etc) in the vicinity of those changes,
and updates about FT2232H clocking issues (they can go faster than the
older chips, and can support adaptive clocking).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
David Brownell [Fri, 5 Mar 2010 18:39:25 +0000 (10:39 -0800)]
ADIv5 share DAP command support
Get rid of needless and undesirable code duplication for
all the DAP commands (resolving a FIXME) ... there's no
need for coreas to have private copies of that stuff.
Stick a pointer to the DAP in "struct arm", letting common
code get to it.
Also rename the "swjdp_info" symbol; just call it "dap".
This is an overall code shrink.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
David Brownell [Fri, 5 Mar 2010 05:51:58 +0000 (21:51 -0800)]
rename "swjdp_common" as "adiv5_dap"
This partially corrects an inappropriate name choice (and its
associated FIXME).
There are still too many variables named "swjdp", bug little
current code actually relies on them referencing an SWJ-DP instead
of some other flavor of DAP. Only the two new dap_to{swd,jtag}()
calls could behave differently on an SWJ-DP instead of a SW-DP or
a JTAG-DP.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
David Brownell [Thu, 4 Mar 2010 05:01:16 +0000 (21:01 -0800)]
NOR: trim range in flash_driver_protect()
When the beginning or end of the specified range of sectors
already has the requested protection status, don't ask the
flash driver to change those sectors.
This will among other things turn command sequences like
this into the NOPs one would expect:
flash protect_check 0
flash info 0
... reports everything as unprotected ...
flash protect 0 0 1 off
That speeds things up (by whatever work was just avoided).
Also, with Stellaris (which can't unprotect flash at page level)
this can eliminate some undesirable/false error reports. (And
finishes fixing a bug currently listed in our bug database...)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
David Brownell [Thu, 4 Mar 2010 04:57:49 +0000 (20:57 -0800)]
NOR: invalidate cached state on target resume
The NOR infrastructure caches some per-sector state, but
it's not used much ... because the cache is not trustworthy.
This patch addresses one part of that problem, by ensuring
that state cached by NOR drivers gets invalidated once we
resume the target -- since targets may then modify sectors.
Now if we see sector protection or erase status marked as
anything other than "unknown", we should be able to rely
on that as being accurate. (That is ... if we assume the
drivers initialize and update this state correctly.)
Another part of that problem is that the cached state isn't
much used (being unreliable, it would have been unsafe).
Those issues can be addressed in later patches.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
projects / openocd / log