Change-Id: I5ebc924ab66c86f1902942bebc203a34d97abc64 Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/1899 Reviewed-by: Paul Fertser <fercerpav@gmail.com> Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk> Tested-by: Spencer Oliver <spen@spen-soft.co.uk>
instead of replicating icepick_d_tapenable in many of TI's newer
platforms, we can move to icepick.cfg and just call it from board TCL
configuration file. This is similar to the C but has a few changes we
need to make.
Change-Id: I0ab48005ccd66cd5b67b919fb5e3b462288f211d Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Tom Rini <trini@ti.com>
Reviewed-on: http://openocd.zylin.com/2030 Tested-by: jenkins Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Jörg Wunsch [Fri, 14 Mar 2014 13:41:51 +0000 (14:41 +0100)]
CMSIS-DAP: print a debug message when the USB product string cannot be read
As suggested by Stian Skjelstad in a comment in:
http://openocd.zylin.com/#/c/2044/
if the USB product string cannot be read, provide a debug message so
users might get aware of a potential permission problem when looking
at the debug output.
Jörg Wunsch [Fri, 14 Mar 2014 10:29:24 +0000 (11:29 +0100)]
Make the Atmel SAM3 family SWD-aware
Atmel's SAM3 and SAM4 processor families are very close to each other
in many respects. However, so far, only the SAM4 target script
contained the magic to allow using SWD, while SAM3 was tied to JTAG
only. This e.g. prevented the CMSIS-DAP driver from accessing SAM3
devices as it only uses SWD transport (by now).
The patch pulls all the things from the SAM4 target script that are
also applicable to SAM3 devices. With the patch, an Atmel CMSIS-DAP
debugger (Atmel-ICE) was proven to be able to successfully attach to a
SAM3S-EK evaluation kit. I also cross-checked that accessing through
a SAM-ICE (Segger J-Link) still works with the patch.
Jörg Wunsch [Fri, 14 Mar 2014 10:00:54 +0000 (11:00 +0100)]
All Atmel-provided CMSIS-DAP devices use 512 byte packet size
The existing CMSIS-DAP driver matches the USB VID/PID against 0x3eb
(Atmel VID) and 0x2111 (Atmel EDBG embedded CMSIS-DAP debugger), and
then bumps the packet size from its default of 64 to 512. However, it
turned out that *all* Atmel-provided CMSIS-DAP devices (EDBG with PID
0x2111; JTAGICE3 with firmware version 3.x, PID 0x2140; new Atmel-ICE
[successor of JTAGICE3], PID 0x2141) require a 512-byte packet size.
Obviously, all run the same USB implementation inside their custom
microcontroller. Thus, it seems best to simply assume that *all*
Atmel CMSIS-DAP devices use this packet size, and don't check the PID
at all.
Jörg Wunsch [Fri, 14 Mar 2014 09:50:36 +0000 (10:50 +0100)]
Prevent segfault when the USB product string cannot be retrieved
In the CMSIS-DAP driver, if nothing has been specified by the user, an
attempt is made to find the first device with the (mandatory)
substring "CMSIS-DAP" in any USB device's product string. However,
while (usually) all devices can be traversed, devices the user does
not have permission for cannot be read the product string from,
resulting in a NULL pointer. Trying to find the substring "CMSIS-DAP"
causes a segementation fault then.
Jens Hoffmann [Sun, 9 Mar 2014 09:42:09 +0000 (10:42 +0100)]
stm32f2x.c: Add STM32F401xE device id.
Nucleo F401 board uses STM32F401RE chip with new device id and
got more flash than existing devices (512K). This patch adds
new the identifier to probe functions so flashing will now work.
Paul Fertser [Fri, 7 Mar 2014 06:45:31 +0000 (10:45 +0400)]
gdb_server: do not copy feature names for tdesc generation
We always have feature names defined by string literals and the
standard guarantees static storage duration for them. Hence, there's
no need duplicating and then freeing them.
Valgrind-tested.
Change-Id: I1b77f966c548e3694141c63bd8680735f0f47505 Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2028 Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The new version of STLink (V2-1) has a different USB endpoint layout.
As the PID of the device also changed it's possible to change EPs used
by OpenOCD in runtime. The patch adds three new fields to stlink_usb_handle_s
and assigns right EP numbers in stlink_usb_open().
Parts of the code inspired by and used with consent of Jens Hoffmann.
Tom Rini [Mon, 3 Mar 2014 20:14:47 +0000 (15:14 -0500)]
interface/ftdi/xds100v2.cfg: Add another VID/PID, drop desc
The XDS100v2 is often embedded in a number of platforms using the
VID/PID of 0x0403/0x6010 and a generic FTDI device description. Add
this VID/PID combination and remove the description line.
Change-Id: I370e6199ac24f802426e9541e19ee38f18f1209a Signed-off-by: Tom Rini <trini@ti.com>
Reviewed-on: http://openocd.zylin.com/2016 Tested-by: jenkins Reviewed-by: Paul Fertser <fercerpav@gmail.com> Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
stlink: Use callback to increase frequency of trace data sampling
The ST-LINK/V2 has limited internal buffering, such that trace data
can be missed if the target is generating data at a rate quicker than
the OpenOCD trace sampling. The issue of lost data is compounded since
individual TPIU packets may be split across individual STLINK_TRACE_EP
reads, and misleading results can occur if mid-packet loss occurs.
This patch increases the frequency of checking for pending trace data
with the aim of minimising such losses. Note: With the limited (I/O
and memory) bandwidth of the ST-LINK/V2 there cannot, however, be a
guarantee against trace data loss.
The timer callback is only added when enabling tracing, and is removed
when tracing is disabled.
Change-Id: Ibde9794b77793d3068f88cb5c1a26f9ceadcbd8a Signed-off-by: James G. Smith <jsmith@ecoscentric.com> Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/1661 Tested-by: jenkins
Kamal Dasu [Thu, 24 Oct 2013 18:58:55 +0000 (14:58 -0400)]
cortex_a: Fix endianess issues in cortex_a8_*_apb_ab_memory
Make the APB-AB memory read routines handle endianess order
when running on big endian host. cortex_a8_read_apb_ab_memory
is also called by cortex_a8_write_apb_ab_memory and was breaking
both APB-AB read and write functions. Also fixed bug in write
function in calculating the offset of end of buffer data. The
change aslo fixes the read issues with all combinations of
aligned unaligned memory access found by 'test_mem_access' cmd.
Tested with target "test_mem_access 4000", also size 1-9,
'mdb/h/w' 'mwb/h/w' cmds and equivalent gdb 'x' 'set' cmds.
Change-Id: Ia927c60c4837617f5342a9beb6fdab1f061855fe Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Reviewed-on: http://openocd.zylin.com/1781 Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com> Tested-by: jenkins
This makes the listing easier to read, imho. The tab indentation
technique causes the base address to precess as the parser proceeds
through the subtables, and can easily wrap.
Chris Johns [Tue, 28 May 2013 23:47:34 +0000 (09:47 +1000)]
targets: Print nested ROM tables with the 'dap info' command.
Move the ROM table printing into a separate function to allow
recursive calls with nested tables. ROM tables can nest. The
printing is limited to 16 levels.
Update the types of tables printed. When an entry can't be read, print
a warning and continue.
Change-Id: Ib134edd9e987af2f5f606071521885b17af4d70f Signed-off-by: Chris Johns <chrisj@rtems.org>
Reviewed-on: http://openocd.zylin.com/1427 Tested-by: jenkins Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Andrey Yurovsky [Wed, 26 Feb 2014 06:18:03 +0000 (22:18 -0800)]
Add support for the Atmel SAMG53
flash: at91sam4: add support for the SAMG53 family (this also covers the
SAMG51). The SAMG5x parts have an EEFC (enhanced embedded flash controller)
which seems to be identical to the EFC that the sam4 driver supports.
Add a script for the Xplained Pro G53 board, this has the onboard CMSIS-DAP
debugger and a SAMG53N19. Tested on this board and chip combination.
Jens Bauer [Tue, 25 Feb 2014 21:05:13 +0000 (22:05 +0100)]
CMSIS-DAP: Fix build errors on Mac OS X
Rename the argument variable 'wait' to 'delay', as 'wait'
conflicts with an API function declared in system header
/usr/include/sys/wait.h on Mac OS X.
gdb_server: fix memory leaks in users of get_reg_features_list()
v4:
- changed first line of commit message
v3:
- added extra LOG_ERROR() message
v2:
- Added missing "goto error"
- free also the on extra element of features[]
In contrast to target_get_gdb_reg_list(), the list returned by
get_reg_features_list() consists of items which are itself
malloc'ed.
--> Free the list items prior freeing the list itself.
Additionally:
- gdb_generate_target_description():
o Do error handling similar as gdb_get_target_description_chunk() does.
- gdb_get_target_description_chunk()
o **features must be initialised prior an "goto error" can happen
Change-Id: Iad07824618c51084e0aa0499ee6fc96198b320f0 Signed-off-by: Christian Eggers <ceggers@gmx.de>
Reviewed-on: http://openocd.zylin.com/1917 Tested-by: jenkins Reviewed-by: Trevor Woerner <trevor.woerner@linaro.org> Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
gdb-server/rtos: Send correct answer to "qfThreadInfo" packet
Even if no RTOS is configured, "qfThreadInfo" must be answered with "l"
instead of "". Otherwise GDB will switch to the older thread packet ("qL"),
which is not supported by OpenOCD.
Change-Id: Iead045bdf8268bac2378c8f70829b17c37834e44 Signed-off-by: Christian Eggers <ceggers@gmx.de>
Reviewed-on: http://openocd.zylin.com/1925 Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Each RTOS implementation uses it's own (similar) code to free
the thread list. There are some additional issues:
<--->
if (pointer != NULL)
free(pointer);
<--->
This is not necessary, free(NULL) is perfectly ok.
<--->
free(rtos->thread_details);
rtos->thread_details = NULL;
rtos->thread_count = 0;
<--->
The 3rd line has been missing for all RTOS but ChibiOs. There are paths
in the code where rtos->thread_count is never set to NULL, which can
lead to null pointer dereference of rtos->thread_details.
Change-Id: I6f7045c3d4518b925cb80dd5c907a566536b34ad Signed-off-by: Christian Eggers <ceggers@gmx.de>
---
Changelog:
v7:
- rtos_wipe_threadlist() --> rtos_free_threadlist()
- removed non related changes in gdb_server.c from this patch
v3:
- Removed world "topic" from first line of commit message
v2:
- typo: "whipe" --> "wipe"
Reviewed-on: http://openocd.zylin.com/1916 Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Nemui Trinomius [Tue, 11 Feb 2014 07:09:32 +0000 (16:09 +0900)]
fm3: fix erase flash fail on using High Level Adapters.
This fix can "erase flash" on using High Level Adapters by running algorithm.
Because fm3 flash commands must need true 16-bit memory access,
but High Level Adapters(ST-Link/TI-ICDI) can 8/32bit access only.
Tested on MB9BF618T and MB9AF112K with STLink/V2.
Antony Pavlov [Sat, 8 Feb 2014 20:11:42 +0000 (00:11 +0400)]
drivers/jtag: usb_blaster: make command handlers more strict
If user used wrong argument number for some usb_blaster_* commands
then openocd show just warning message.
This commit makes command handler's behaviour more strict and
openocd treats wrong argument number as an error.
In addition we already have 'help' and 'usage' information in
struct command_registration ublast_command_handlers[],
so we can drop redundancy messages in command handlers.
Change-Id: I73b8c75ec60a18e5258a4bdffe972e8a1afc1066 Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
Reviewed-on: http://openocd.zylin.com/1942 Tested-by: jenkins Reviewed-by: Paul Fertser <fercerpav@gmail.com> Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Paul Fertser [Tue, 4 Feb 2014 12:07:57 +0000 (16:07 +0400)]
tcl/drscan: handle invalid syntax with a conditional, not assert
When "drscan" command is used improperly, such as in:
drscan stm32f1x.cpu -endstate drpause
there're no fields to scan, and so the assert leads to a
segfault. This should be treated like any other syntax error instead.
Change-Id: Id1743f5d641038e1e3754c6f3097aabc5d1916b9 Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1927 Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Paul Fertser [Thu, 30 Jan 2014 10:11:13 +0000 (14:11 +0400)]
arm926ejs: fix write memory operations with caches enabled
Perform proper ICache flush operations on memory writes. This should fix
inability to use software breakpoints for debugging with caches
enabled.
This patch is only compile-time tested.
Commit 1137eaedaf6498f3448cdedf6f93076d9b3fd58a fixed the same issue
for arm920t. Among all the arm7_9_common targets only arm926ejs seems
to be broken in the same way.
Change-Id: I575306ac4319a69fc637b42f7c958f4595c5e81f Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1912 Tested-by: jenkins Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Paul Fertser [Sat, 18 Jan 2014 16:24:24 +0000 (20:24 +0400)]
interface/ftdi/xds100v2.cfg: default to reset state and ask user to release it later
This adapter is special and needs a reset sequence to be performed
before operation. Since there're no suitable hooks to do that, we have
no choice but to ask the user to manually add the necessary commands
to his or her config file.
Change-Id: I48fb4276e77529768266840221b68c3ae26801e1 Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1884 Tested-by: jenkins Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Paul Fertser [Tue, 29 Oct 2013 09:45:07 +0000 (13:45 +0400)]
cortex_a: do not try to use MMU for translation if it wasn't enabled on target stop
On a target where AHB AP memory access is unavailable, care should be
taken to avoid treating addresses as virtual if the MMU was disabled
at the time the target was stopped.
Without this it's impossible to peek memory with Gdb when debugging
e.g. a bootloader because cortex_a8_read_memory() unconditionally
tried (and failed because of a sanity check in cortex_a8_mmu_modify)
to enable MMU.
Change-Id: Id7c63f4912920fb71a6104226ec6428d18c96a56 Reported-by: mbm@openwrt.org Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1787 Tested-by: jenkins Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Anton Kolesov [Wed, 22 Jan 2014 16:18:56 +0000 (20:18 +0400)]
gdb_server: Fix confusing warning when entering noack mode
Comment in gdb_server code mistakenly attributed constant warnings
about unexpected acknowledgement to the ACK packet sent by GDB when
establishing connection. However that is not the case, OpenOCD
gdb_server is handling this packet correctly without an warnings. This
warning instead was caused by the ACK packet which GDB sends right after
going into noack mode. Because OpenOCD gdb_server is already in noack
mode at this state, it emits warning about it. This is a documented GDB
behaviour
(https://sourceware.org/gdb/onlinedocs/gdb/Packet-Acknowledgment.html)
so there is no reason to scare users with warnings in this case.
This patch basically introduces two-level noack mode: after receiving
QStartNoAckMode gdb_server will set noack_mode to 1, then it will
receive this last ACK packet, but instead of printing a warning,
noack_mode will be increased to 2. Should there be any other ACK packets
after that, they will be properly reported by warning. All other code
that relies on noack_mode checks it for "!= 0", so there will be no
difference if it is 1 or 2.
Change-Id: I0e9c57fd93293bfe010390db2f3f161528b11d86 Signed-off-by: Anton Kolesov <anton.kolesov@synopsys.com>
Reviewed-on: http://openocd.zylin.com/1895 Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Paul Fertser [Fri, 17 Jan 2014 10:11:55 +0000 (14:11 +0400)]
target/nds32_disassembler: fix format specifiers warnings
According to the standard every operation returns at least an integer,
so PRIu8 format specifier is not suitable for these values as is.
This breaks build on OS X (x86_64-apple-darwin13.0.0) with "Apple LLVM
version 5.0 (clang-500.2.79) (based on LLVM 3.3svn)".
Fix by adding appropriate casts. In fact there's plenty of room (and
I'd say necessity) for factoring out common code in there, but it's
too invasive for a non-maintainer.
Change-Id: I7d2182eb1d2f86fa22c882fbbaa6cfadf1c3e8fc Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1878 Tested-by: jenkins Reviewed-by: Xiaofan <xiaofanc@gmail.com> Reviewed-by: Hsiangkai Wang <hsiangkai@gmail.com> Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Paul Fertser [Fri, 17 Jan 2014 10:08:07 +0000 (14:08 +0400)]
rtos: fix uninitialised variable warning
Breaks build with clang 3.3. This "addr" variable is actually always
ignored by next_symbol() when cur_symbol is an empty string but clang
can't (and probably shouldn't) prove that automatically.
Change-Id: Id030f1aa34b9d40b5fa20a422031511520e52669 Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1876 Tested-by: jenkins Reviewed-by: Xiaofan <xiaofanc@gmail.com> Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Paul Fertser [Sun, 2 Feb 2014 09:04:41 +0000 (13:04 +0400)]
interface/ftdi: add TUMPA Lite config
TUMPA Lite is a cheap FT232H-based breakout board, without any
buffering. It also lacks series resistors so for some targets
(especially when not using ridiculously short wires) one needs to add
about 47 Ohms in series on every high-speed line.
The SRST line is connected directly to the FT232H too.
Real-life tested (including SRST and TRST).
Change-Id: I5ed4f88d8d20384e9c52efe2ff0c290e2650d43e Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1918 Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Nemui Trinomius [Wed, 22 Jan 2014 14:46:32 +0000 (23:46 +0900)]
kinetis : improve kinetis flash driver.
Kinetis K-series have different guranuarity for each frequency model.
This patch adding more minute guranuarity detection.
And adopted mass erase command not only L-series but also K-series.
Tested on MK20DX32VLF5,MK10DX32VLF5,and MKL25Z128VLK4.
Spencer Oliver [Wed, 22 Jan 2014 11:04:26 +0000 (11:04 +0000)]
cfg: LPC17xx default to using SYSRESETREQ to reset target
Originally the LPC17xx user guide (UM10360 Rev 2) stated that SYSRESETREQ
was not supported, so this was the default cortex_m reset mode.
Rev 3 of the same user guide states that it is now supported.
This has been verified on a LPC1768 mbed platform, previously I have not
tested this functionality.
Change-Id: I4858248903981a1c93ce75016e67c9e02702fcc5 Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1892 Tested-by: jenkins Reviewed-by: Jörg Fischer <turboj@gmx.de> Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Paul Fertser [Tue, 26 Nov 2013 15:46:09 +0000 (19:46 +0400)]
arm920t: fix write memory operations with caches enabled
Commit ff5ec942d80a34e20b5a3ca3328f7e6a55fb309b made this target
always use generic arm7_9 memory write routines for software
breakpoints which resulted in inability to debug and single-step
sources in Gdb when icache is active as generic routine doesn't
invalidate it. This should fix it (and is real-life tested against
Samsung S3C2442). I expect other arm7-9 targets to be affected as
well.
Change-Id: Id7980e370ae4db47ac6b1490321d81ffe85711c0 Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1817 Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk> Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Peter Lawrence [Tue, 21 Jan 2014 00:08:58 +0000 (17:08 -0700)]
CMSIS-DAP: auto-detect CMSIS-DAP USB VID:PID
The current OpenOCD implementation requires CMSIS-DAP adapter USB
VID:PID values to either be hard-coded in the source or manually
supplied by the user's configuration files. The CMSIS-DAP
specification stipulates that all compliant adapters should have
"CMSIS-DAP" in the product string. This should obviate the need
for hard-coding.
This patch was previously submitted as changes 1882, 1883, and 1886
but amendments failed to be registered by the server. The
functionality was changed from 1886 in response to comments so that
user-supplied VID:PID values overrided the CMSIS-DAP auto-detect.
Change-Id: Ifb2dc217248359f448e0a42bd1527dd744c434b0 Signed-off-by: Peter Lawrence <majbthrd@gmail.com>
Reviewed-on: http://openocd.zylin.com/1888 Tested-by: jenkins Reviewed-by: Xiaofan <xiaofanc@gmail.com> Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Paul Fertser [Mon, 6 Jan 2014 17:36:21 +0000 (21:36 +0400)]
gdb_server: check for invalid read memory requests
This prevents invalid free(NULL) (that crashes OpenOCD on desktop
distros).
With radare2 it's now a bit more useful, memory access works if I seek
to the correct address, can't test further as it apparently lacks thumb2
support.
Change-Id: I6ec32d09fd52dab53ba765d7f7519baa1f55d973 Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1853 Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Franck Jullien [Sun, 3 Nov 2013 16:31:44 +0000 (17:31 +0100)]
jtag/drivers: add USB-Blaster II
This patchs adds a new access driver for the existing
USB-Blaster interface driver.
This interface (as it is build-in on the sockit development
board) is composed of a Cypress EZ-USB plus a CPLD.
The Cypress chip as an embedded 8051 microcontroller.
When it's powered up, the firmware is downloaded to the
chip then the device is disconnected and reconnected with
the new firmware.
The USB-Blaster II protocol is almost identicial to
the old one. The only difference is that you need to
send a 0x5F before read TDO back. This command
seems to copy TDO buffer datas to the endpoint buffer.
Driver will be auto enabled if libusb-1.0 is detected.
Change-Id: I562a720a68cb4dcabeab791947d5d38776cb70fa Signed-off-by: Franck Jullien <franck.jullien@gmail.com>
Reviewed-on: http://openocd.zylin.com/1791 Tested-by: jenkins Reviewed-by: Robert Jarzmik <robert.jarzmik@free.fr> Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Robert P. J. Day [Mon, 13 Jan 2014 11:49:33 +0000 (06:49 -0500)]
Grammatical cleanup to Tcl Scripting chapter of User's Guide
Changes solely to the Tcl Scripting API chapter of the UG:
* Some grammatical cleanup
* Fix formatting issues (@example and @verbatim formatting)
* Add references to missing OSes OpenBSD, NetBSD and eCos.
Change-Id: I3ec1a192a0b1e0a207dceb76fd39008d01e287a5 Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Reviewed-on: http://openocd.zylin.com/1872 Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
cortex_m: Avoid unnecessary saving and restoring of DCRDR
This is used for the emulated DCC channel which is only maintained as long
as target->dbg_msg_enabled is set. Skip the saving and restoring if not
enabled to save one dap_run() per core register access.
Note that we could've probably queued all core register accesses in the
same transaction if the armv7 register framework hadn't required
synchronous register accesses.
Change-Id: I4fe6d713261ee5db42422203eb63035fdcc48891 Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/1848 Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Nemui Trinomius [Fri, 27 Dec 2013 03:25:33 +0000 (12:25 +0900)]
lpc2000: fix LPC810 programming support
IAP commands fail on programming LPC810 because it has only 1kByte of SRAM.
This patch is fixing cmd51_max_buffer suitable size for LPC810,LPC811 and
other LPC1000 series.
Tested on a LPC810,LPC812,LPC11u14,and LPC1114(DIP28).
Robert P. J. Day [Sat, 11 Jan 2014 10:35:49 +0000 (05:35 -0500)]
A few more grammar and typo fixes from the User's Guide.
More cleanup from some of the later chapters from the User's Guide,
no functional changes.
Change-Id: Ib2860fc2574503e8107935d79db45fa96014fe3a Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Reviewed-on: http://openocd.zylin.com/1863 Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Robert P. J. Day [Sat, 11 Jan 2014 09:42:35 +0000 (04:42 -0500)]
Remove obsolete tip referring to 2010 removal of TAP numbers.
Remove a tip describing the discouraged use of TAP numbers, and how
these numbers would be removed by mid-2010.
Change-Id: Iebe7e2e4a0f8e1f18a91d7935588dd9ced2b398d Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Reviewed-on: http://openocd.zylin.com/1862 Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Robert P. J. Day [Fri, 10 Jan 2014 17:15:52 +0000 (12:15 -0500)]
Proofreading, typo and grammar fixes to Ch 10 User's Guide.
Various cleanups to Chapter 10 of the User's Guide, no functional
changes.
Change-Id: I055d032eacc8e85b1d8edbd4bcc505f6f0feaa49 Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Reviewed-on: http://openocd.zylin.com/1861 Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Some minor URL fixes and typo fixes, no functional changes.
Change-Id: Ib262d9e6330c35d26868942b821de7b53e00b854 Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Reviewed-on: http://openocd.zylin.com/1859 Tested-by: jenkins Reviewed-by: Bill Traynor <btraynor@gmail.com> Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Andrey Yurovsky [Fri, 4 Oct 2013 03:41:33 +0000 (20:41 -0700)]
add support for Atmel SAMD NOR Flash
This adds a new NOR Flash driver, "at91samd", which supports the
built-in Flash on Atmel's D-series Cortex M MCUs, starting with the D20.
Parts and their geometry are detected automatically using the DSU and
lookup schemes described in the D20 document, 42129F–SAM–10/2013.
Future D-series variants and families should presumably use this
controller as well (possibly with minor changes and improvements).
Tested on the SAMD20 Xplained Pro board, for which we also add the
corresponding Flash configuration.
This adds a new NOR Flash driver, "at91sam4l", which supports the
built-in Flash on Atmel's low-power SAM4L family of Cortex M4 MCUs.
Parts and their geometry are detected automatically using the Chip ID
and lookup schemes described in document 42023E–SAM–07/2013.
Tested on AT91SAM4LC4CA via the SAM4L XPlained Pro development kit.
Spencer Oliver [Mon, 4 Nov 2013 21:24:39 +0000 (21:24 +0000)]
cfg: add initial Atmel xplained kit support
These kits feature a CMSIS-DAP compliant debugger and so have been added
as part of the pending support.
Currently the flash drivers for the L8 and D20 are wip.
One issue this implementation of CMSIS-DAP raised is that it supports
512byte HID reports, however using the current HIDAPI we have no cross platform
way of querying this info. Long term we plan to add this support to HIDAPI.
Change-Id: Ie8b7c871f58a099d963cd71a9f8a0105a38784e9 Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1625 Tested-by: jenkins
Spencer Oliver [Thu, 19 Dec 2013 21:33:19 +0000 (21:33 +0000)]
cmsis-dap: add initial cmsis-dap support
This is based on work from:
https://github.com/TheShed/OpenOCD-CMSIS-DAP/tree/cmsis-dap
Main changes include moving over to using HIDAPI rather than libusb-1.0
and cleaning up to merge into master. Support for reset using srst has
also been added.
It has been tested on all the mbed boards as well as the Freedom board
from Freescale. These boards only implement SWD mode, however JTAG mode
has been tested with a Keil ULINK2 and a stm32 target - but requires a lot
more work.
Change-Id: If3dba057127b54b15ca7f364f37c6286d34f77e0 Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com> Reported-by: Robert P. J. Day <rpjday@crashcourse.ca>
Reviewed-on: http://openocd.zylin.com/1858 Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
projects / openocd / log