Diego Herranz [Thu, 3 Aug 2017 06:37:41 +0000 (07:37 +0100)]
tcl/interface/ftdi: improve minimodule config
- Tested on a real FT2232H MiniModule, so warning removed.
- Every pin initially set to high impedance except TCK, TDI,
TDO and TMS: Safest values given it's an evaluation board
and the rest of pins might be connected to something else.
- Reset is now initially de-asserted (it was asserted
which is not recommended).
- nRST pin choice is arbitrary so comment added (wondering
if it should be an "echo").
- "-oe" option added to NRST signal so it can be set as
high impedance (tri-stated).
Change-Id: I967ab0c7bbccf72dbf6d6d78b3180b74e016e0d6 Signed-off-by: Diego Herranz <diegoherranz@diegoherranz.com>
Reviewed-on: http://openocd.zylin.com/4185 Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The migration from the old ft2232 driver to the new generic ftdi driver
ended up breaking support for the SheevaPlug device. The old driver
defaulted to channel 1, but numbered the channels 1 to 4. The new driver
starts at 0. The SheevaPlug JTAG is on interface A (interface B is the
serial console), so it should be using channel 0. Fix this. Confirmed
as working; serial console remains available and a new u-boot image can
be transferred across using the JTAG link.
See also Debian Bug#837989; https://bugs.debian.org/837989
Change-Id: I4ac2bfeb0d1e7e99d70fa47dc55f186e6af2c542 Signed-off-by: Jonathan McDowell <noodles@earth.li>
Reviewed-on: http://openocd.zylin.com/4206 Reviewed-by: Paul Fertser <fercerpav@gmail.com> Tested-by: jenkins
Marc Schink [Thu, 24 Aug 2017 15:42:28 +0000 (17:42 +0200)]
stm32f2x: Fix left shift of negative value
Use unsigned constant for left shift operation in order to avoid the
following error with GCC >= 6.0:
../src/flash/nor/stm32f2x.c: In function ‘stm32x_handle_unlock_command’:
../src/flash/nor/stm32f2x.c:1324:67: error: left shift of negative value [-Werror=shift-negative-value]
stm32x_info->option_bytes.optcr2_pcrop = OPTCR2_PCROP_RDP | (~1 << bank->num_sectors);
Change-Id: I0ac082bd0dbb8dc2f61ffff8fdf486ab7962d2e0 Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-on: http://openocd.zylin.com/4207 Tested-by: jenkins Reviewed-by: Andreas Bolsch <hyphen0break@gmail.com> Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk> Reviewed-by: Anton Fosselius <anton.fosselius@gmail.com> Reviewed-by: Esben Haabendal <esbenhaabendal@gmail.com>
Karl Palsson [Wed, 10 May 2017 14:37:51 +0000 (14:37 +0000)]
telnet_server: increase buffer sizes to allow longer commands.
A common use case seen in the wild is echoing a string of commands to an
existing openocd instance via netcat. The sequence of ; separated
commands can easily run over the line limit of only 256 chars.
Increasing this dramatically reduces surprises, at the expense of a tiny
amount of extra ram usage.
Change-Id: I2389d99d316a96b5fa03f0894b43c412308e12c4 Signed-off-by: Karl Palsson <karlp@tweak.net.au>
Reviewed-on: http://openocd.zylin.com/4132 Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Andreas Bolsch [Sun, 5 Mar 2017 18:01:06 +0000 (19:01 +0100)]
Support for STM32F722, F723, F413 and F423
IDs for STM32F722, F723, F413 and F423 added, handling of PCROP
for F722/723 and additional nWPRT bits for F413/423 implemented.
The additional protection bit positions for F413/423 conflict
with other options bits for the F7xx variants, additionally the
last two sectors share a common bit.
Protection for F413 and F767/777 now use protection blocks
rather sectors for dealing with protections bits.
Checking for halted state in 'lock' and 'unlock' removed: When
PCROP is activated in F723, halted state is not detected properly,
but lock/unlock sequence is required to disable PCROP.
Tested with STM32F723E-Disco, STM32F413ZH-Nucleo.
Change-Id: Ie6ddab47a9ae8461087d369b4f289b7f9d1e031c Signed-off-by: Andreas Bolsch <hyphen0break@gmail.com>
Reviewed-on: http://openocd.zylin.com/4045 Tested-by: jenkins Reviewed-by: Tomas Vanek <vanekt@fbl.cz> Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Tomas Vanek [Thu, 13 Jul 2017 19:35:22 +0000 (21:35 +0200)]
flash Kinetis: fix probe for FlexNVM partitioned as EEPROM backup
If a MCU has FlexNVM partitioned as EEPROM backup only
(no data flash), kinetis_probe_chip() detects zero fcfg2_maxaddr1
and adjusts flash banks count to 1, what is obviously wrong.
The change limits the test to devices without FlexNVM.
Computation of program flash/FlexNVM blocks is now more robust.
Missing case 0x07 is added to switch (fcfg1_depart)
Change-Id: I0bd6030a0fe1ab62aeb0223bbdf2aee1505bf6a0 Reported-by: simon.haines@scalardata.com Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4180 Tested-by: jenkins Reviewed-by: Simon Haines <simon.haines@scalardata.com> Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Tomas Vanek [Thu, 29 Jun 2017 21:06:55 +0000 (23:06 +0200)]
flash Kinetis: fix devices with smallest program flash (8 and 16 kB)
Change-Id: I2692b9877a7f877104528f279a69e8cc1cfbcdbf Reported-by: David Miller Lowe <milhead@gmail.com> Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4173 Tested-by: jenkins Reviewed-by: Miller Lowe <miller.lowe@trailtech.net> Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Steven Stallion [Thu, 22 Jun 2017 05:14:08 +0000 (22:14 -0700)]
rtos: better sanity checking for uCOS-III
This patch improves the OSRunning check. If the rtos_running check
fails, update_threads will return an error rather than attempt to update
the thread list using bad values.
Change-Id: I8614c325504d3a9ab19aebb6862b1fe445a0c8e7 Signed-off-by: Steven Stallion <stallion@squareup.com>
Reviewed-on: http://openocd.zylin.com/4166 Tested-by: jenkins Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Steven Stallion [Wed, 3 May 2017 17:17:45 +0000 (12:17 -0500)]
rtos: style corrections for uCOS-III
This patch corrects a number of style infractions in RTOS support for
uC/OS-III. These were missed during initial review last year prior to
the 0.10.0 release.
Change-Id: Ia2139f6ca381d4087fd8ee989f7a03ac474d7440 Signed-off-by: Steven Stallion <stallion@squareup.com>
Reviewed-on: http://openocd.zylin.com/4120 Tested-by: jenkins Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tomas Vanek [Fri, 10 Mar 2017 20:43:46 +0000 (21:43 +0100)]
flash Kinetis: add KL28 device
This device differs a lot from others in KL series.
Unfortunately the System Integration Module, where device
identification resides, moved to a new address so probe now have
to try both addresses of SIM_SDID.
Introduce a new bank creation option: -sim-base to ensure error free probe.
WDOG32 is slightly different from KE1x and on different address.
System Mode Controler changed layout to word aligned.
Tomas Vanek [Mon, 26 Dec 2016 14:20:33 +0000 (15:20 +0100)]
flash Kinetis: implement automatic bank creation based on device probe
Kinetis flash driver services huge number of MCU types. They have
one, two or four flash banks with option of FlexNVM. It would
require ~36 config files just for Kx series, more for KLx, KVx and KE1x.
The change implements alternative approach:
- configuration file creates just one pflash bank (common for all devices)
- when a device is probed, additional pflash or flexnvm banks are created
based on flash layout of the connected MCU
- created banks have names with optional numbering e.g. kx.pflash0 kx.pflash1
kx.flexnvm0 kx.flexnvm1
- the first bank gets renamed if numbering is used
Automatic bank creation is enabled by tcl command 'kinetis create_banks'.
Used solution has a drawback: other banks than pflash0 are not accessible
until pflash0 is probed. Fortunately gdb attach and standard programming
accesses banks in right sequence.
Tomas Vanek [Mon, 26 Dec 2016 09:15:06 +0000 (10:15 +0100)]
flash Kinetis: split kinetis_chip from kinetis_flash_bank
Kinetis flash driver probed and decoded chip repeatedly for each flash
bank. Bank ordering used global bank number so multi-target
configuration was broken.
The change introduces kinetis_probe_chip() which reads SIM SDID
and SIM FCFG registers, decodes Kinetis series and family
and fills struct kinetis_chip. This probe runs once for all banks.
struct kinetis_chip contains pointers to all flash banks embeded
in the MCU. It simplifies iteration over all or specific MCU banks.
kinetis_probe_chip() generates MCU name and some informational messages
are improved.
Tomas Vanek [Fri, 2 Dec 2016 14:47:01 +0000 (15:47 +0100)]
flash Kinetis: add KL8x family, fix erase check
Secure devices KL81Z7 and KL82Z7 have no SERIESID field in ID register
so they have to be decoded in Kx branch (not KLx).
The flash controller in KL8x and also in K8x devices does not implement
FTFx_CMD_BLOCKSTAT command. Fix kinetis_blank_check() to work properly
using FTFx_CMD_SECTSTAT command only.
Introduce a new flag FS_NO_CMD_BLOCKSTAT to avoid use of FTFx_CMD_BLOCKSTAT
on these devices.
Tomas Vanek [Wed, 30 Nov 2016 20:48:59 +0000 (21:48 +0100)]
flash Kinetis: add KE1xZ and KE1xF families
The new Kinetis KE1x families use FTFE flash controller unlike KE0x.
Also SDID coding corresponds to new K, KL and KV families.
That's why KE1x is handled by kinetis driver instead of kinetis_ke
Tomas Vanek [Thu, 14 Jul 2016 18:52:13 +0000 (20:52 +0200)]
flash/nor: at91samd modified to use real erase sector size
Before this change SAMD driver defined "sector" equal to a flash
protection block. Oversize sectors (16kB for the biggest flash size)
made problems for flashing firmware split to two or more parts.
Removed superfluous test of sector protection before erase.
Tomas Vanek [Mon, 26 Dec 2016 21:53:44 +0000 (22:53 +0100)]
flash/nor/at91sam4: remove FWS=6, rename at91samg to atsamg
FWS=6 workaround removed, as this appears to be a copy-paste error
from the SAM3X family. Originally addressed in http://openocd.zylin.com/3837
but not all occurences were removed.
Atmel changed chip naming and removed 91 prefix for atsamg, samd...
Extended and revised version of my original patch submitted by Dmytro
here: http://openocd.zylin.com/#/c/3390
This driver is using pure SPI mode, so the flash base address is not
used except some flash commands (e.g. "flash program") need it to
distinguish the banks.
Example config with all 3 chip selects:
flash bank flash0 ath79 0 0 0 0 $_TARGETNAME cs0
flash bank flash1 ath79 0x10000000 0 0 0 $_TARGETNAME cs1
flash bank flash2 ath79 0x20000000 0 0 0 $_TARGETNAME cs2
Example usage:
> flash probe flash0
Found flash device 'win w25q128fv' (ID 0x001840ef)
flash 'ath79' found at 0x00000000
> flash probe flash1
No SPI flash found
> flash probe flash2
No SPI flash found
> flash banks
> flash read_bank flash0 /tmp/test.bin 0x00000000 0x1000
reading 4096 bytes from flash @0x00000000
wrote 4096 bytes to file /tmp/test.bin from flash bank 0 at offset
0x00000000 in 28.688066s (0.139 KiB/s)
Grzegorz Kostka [Tue, 18 Apr 2017 14:12:58 +0000 (16:12 +0200)]
imx_gpio: add mmap based jtag interface for IMX processors
For some targets (like nrf51) sysfs driver is too slow. This
patch implements memory maped driver for IMX processors.
Mostly based on bcm2835gpio. Tested on imx6ul CPU. However, it should
work on any NXP IMX CPU.
Change-Id: Idace4c98181c6e9c64dd158bfa52631204b5c4a7 Signed-off-by: Grzegorz Kostka <kostka.grzegorz@gmail.com>
Reviewed-on: http://openocd.zylin.com/4106 Tested-by: jenkins Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Salvador Arroyo [Mon, 20 Feb 2017 19:45:37 +0000 (20:45 +0100)]
mips32, use scan32 function for reading impcode/idcode.
There is no need to implement scan code in functions
mips_ejtag_get_idcode/impcode(), use mips_ejtag_drscan_32().
Impcode/idcode saved in ejtag.info.
Reorder the code in the callers of this functions.
Change-Id: Ia829c783a0b24c6a65cade736113fa6f67b0a170 Signed-off-by: Salvador Arroyo <salvador@telecable.es>
Reviewed-on: http://openocd.zylin.com/4003 Tested-by: jenkins Reviewed-by: Peter Mamonov <pmamonov@gmail.com> Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Salvador Arroyo [Mon, 8 May 2017 07:44:50 +0000 (09:44 +0200)]
mips32: add micromips breakpoints support
Breakpoint setting based on length (kind) only.
Added 16bit aligned 32bit software breakpoints
support and same filtering before setting
breakpoint.
Set the required isa bit in hardware breakpoints.
Drop the isa bit in software breakpoints.
Salvador Arroyo [Sun, 7 May 2017 16:39:17 +0000 (18:39 +0200)]
mips32: add micromips isa handling
Read and save configuration registers, up to 4.
Config3 holds the micromips implementation info.
Added isa implementation info to mips32_common.
Added isa filter to avoid common mistakes, but only
if one isa mode is implemented.
When resuming the isa requested is set if more than
one isa mode is implemented.
Salvador Arroyo [Sun, 7 May 2017 09:58:25 +0000 (11:58 +0200)]
mips32, add support for micromips in debug mode
Micromips is 16bit oriented, branch and jumps are
16 bit based. The upper half 16bits of a 32bit instruction
with the major opcode, must go first in the instruction
stream, hence the SWAP16 macro and swap16 array function,
needed if the code is written as 32 bit word in little endian
cores. Endianess info added to ejtag_iinfo. Pointer to
ejtag_info and isa field added to pracc context.
MIPS32 code are renamed to MIPS32_ISA_...
To select the isa, the new code has an additional isa parameter
(1 for micromips, 0 for mips32).
In JR instruction the isa bit must be set to execute
micromips code.
The suffix u is added to the OP codes to avoid signed/unsigned
comparison errors and to make sure the right shift is
performed logically.
The isa in debug mode is updated in the poll function.
Code for miniprograms, in kernel mode, need to be converted.
CFI code only for mips32.
Salvador Arroyo [Mon, 27 Feb 2017 12:06:46 +0000 (13:06 +0100)]
mips32, add microMips instruction subset
Only reencoded MIPS32 instructions. Added some instructions
for crc code. Micromips isa in debug mode is only needed for
pic32mm cores. Pic32mz seems that only works with MIPS32
isa when in debug mode.
Salvador Arroyo [Mon, 27 Feb 2017 11:25:49 +0000 (12:25 +0100)]
mips32, add option to avoid check in last instruction
This option is needed, for example, when exiting
debug mode in bmips targets. The last instruction
is a NOP, not a DERET. When working in async mode
this check is not done, mips32_pracc_queue_exec() pass
the parameter to mips32_pracc_exec() and never use it.
Salvador Arroyo [Sun, 26 Feb 2017 19:35:01 +0000 (20:35 +0100)]
mips32, add realloc code
If max_code is reached realloc memory. If fails to realloc
the error is propagated and every call to pracc_add() returns
immediately. The exec function logs the error.
Salvador Arroyo [Sun, 26 Feb 2017 08:11:02 +0000 (09:11 +0100)]
mips32, change in pracc_list for dynamic allocation
pracc_list points to an array with code in the lower half
and addr in the upper half. Change it to a struct with
an instruction field and an address field.
Requiered to make reallocation easier.
As a side effect the code is less quirky.
MacOSX tool chain defines __unused in "sys/cdefs.h", causing a collision.
Remove the local define to avoid polluting the compilers internal
symbol namespace.
Salvador Arroyo [Thu, 23 Feb 2017 14:14:46 +0000 (15:14 +0100)]
mips32, mips32_pracc_finish() queued only
In most of the cases there is no need to request execution,
the check for a new pracc access already does it.
Requesting execution if not needed makes execution slower and
code larger due the additional checks.
Reduce code in fasdata transfer function.
Call for execution when exiting debug.
Salvador Arroyo [Wed, 22 Feb 2017 22:14:36 +0000 (23:14 +0100)]
mips32, drop unnecessary code in mips32_pracc.c
Struct mips32_pracc_context no more in use.
In current code cp0 reg/sel do not requires special handling.
In sync mode ctx.store_count not used, drop check.
In fasdata transfer function use mips32_pracc_read_ctrl_addr()
to reduce code.
Salvador Arroyo [Mon, 20 Feb 2017 22:05:38 +0000 (23:05 +0100)]
mips32, add generic scan 32 function
Will be used later, allow queuing all needed scans in a pracc
access. This makes faster execution with ftdi based adapters
working in sync with pracc.
Added now because the overall code is shorter.
Hellosun Wu [Tue, 26 Jan 2016 05:36:49 +0000 (13:36 +0800)]
libusb: Add transfer type filter to get correct ep
The need for this due to AICE having 3 interfaces
(EP1 IN-Interrupt, EP2 OUT-Bulk, EP6 IN-Bulk).
Without it, the function will choose first two endpoint as
read_ep/write_ep. This filter will check transfer types
when get endpoint-id. Without this patch, AICE will not
get correct endpoint.
CezaryGapinski [Mon, 20 Mar 2017 11:33:05 +0000 (12:33 +0100)]
stm32lx: fix dual-bank configuration for Cat.5 and Cat.6 devices
Default values for .first_bank_size_kb and .has_dual_banks fields
described in stm32lx_parts[] do not fully describe
the real device memory layouts.
Basing on:
STM32L0x1 RM0377
STM32L0x2 RM0376
STM32L0x3 RM0367
STM32Lxxxx RM0038
correct values for memory layouts were selected:
id = 0x447 STM32L0xx (Cat.5) <- dual bank flash
for size 192 or 128 KBytes, single bank for 64 KBytes
id = 0x436 STM32L1xx (Cat.4 / Cat.3 - Medium + /
High Density) <- only one size of the bank,
default values are correct
id = 0x437 STM32L1xx (Cat.5 / Cat.6) <- always dual bank,
but size of the bank can be different
For that reason .part_info field in struct stm32lx_flash_bank
is a dynamic field with fields copied from stm32lx_parts[]
and overwriten to correct values
for specific chips and memory sizes.
Fix "couldn't use loader, falling back to page memory writes" error on
stm32l0 which was caused by the use of cortex-m3 instructions in the
flash loader code. The loader is rewritten using cortex-m0 compatible
instructions
Signed-off-by: Armin van der Togt <armin@otheruse.nl>
Change-Id: If23027b8e09f74e45129e1f8452a04bb994c424e
Reviewed-on: http://openocd.zylin.com/4036 Tested-by: jenkins Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Tomas Vanek [Mon, 9 Jan 2017 16:06:52 +0000 (17:06 +0100)]
jtag/drivers cmsis-dap: do not limit speed so strictly
Adapter clock frequency is set by 32-bit number and most adapters
limit the highest speed safely. There is no reason to impose strict
limit of 5000 kHz if some adapters can do more.
While on it give informative error message in case of zero adapter_khz.
board: introduce base config for TI BeagleBone family boards
This patch adds the file ti_beaglebone-base.cfg as the common base
configuration for all TI BeagleBone derived boards. It also modifies
ti_beaglebone.cfg to source the base board and only add the on-board
JTAG adapter. Lastly, it adds a file ti_beaglebone_black.cfg with
a suitable configuraton for the BeagleBone "Black" variant.
Add new entry in nrf51_known_devices_table for nRF51822 chip found on
chinese Core51822 dev board. The chp has markings N51822 / QFAAH1 / 1630FW
Nordic Semiconductor nRF51 Series Compatibility matrix confirms that this chip
has 256K Flash and 16K RAM.
Tomas Vanek [Mon, 9 Jan 2017 14:30:21 +0000 (15:30 +0100)]
jtag/drivers cmsis-dap: fix speed setting on Atmel EDBG
Without the change Atmel EDBG uses default clock freq about 168 kHz
instead adapter_khz configured before interface init.
Changing adapter speed after init works as expected.
Testing shows the EDBG firmware resets speed to default during DAP_SWJ_Sequence.
Tested with fw versions 03.1F.01AE and 02.09.0169
This change repeats the DAP_SWJ_Clock command after sending a SWJ sequence.
Change-Id: Ic70457c5df635f47cad5e70b0dc83a083ea1b3a3 Reported-by: Ladislav Laska <laska@kam.mff.cuni.cz> Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/3944 Tested-by: jenkins Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Austin Morton [Wed, 29 Mar 2017 03:22:44 +0000 (23:22 -0400)]
stlink: increase trace buffer size to maximum allowed on st-link v2 firmware
Increasing the trace buffer size on the st-link itself gives openocd a greater
chance of avoiding trace data overflowing within the st-link between polls
when there is a large amount of data being sent over the trace port
The st-link appears to split the given buffer size in half
while one half is awaiting transfer over USB, the other half is being
filled by DMA transfer. If you do not poll frequently enough, the DMA
transfer will overflow back to the start of its current buffer, resulting in
corrupted output
Buffer size of 4096 bytes is the maximum allowed by the st-link v2
projects / openocd / log