Mike Dunn [Thu, 9 Sep 2010 02:13:14 +0000 (19:13 -0700)]
xscale: mark xscale registers invalid on debug entry
Hi everyone,
This simple patch fixes a problem I noticed on the xscale where incorrect values
are sometimes reported by the reg command. The problem can occur when
requesting the value of registers in the xscale-specific register cache. With a
couple of exceptions, none of the registers in the xscale register cache are
automatically retrieved on debug entry. This is probably fine, as they are
unlikely to be needed on a regular basis during a typical debug session, and
they can be retrieved when explicitly requested by name using the reg command.
The problem is that once this is done, the register remains marked as valid for
the remainder of the OpenOCD session, and the reg command will henceforth always
report the same value because it is obtained from the cache and is never again
retrieved from the debug handler on the target.
The fix is to mark all registers in the xscale register cache as invalid on
debug entry (before the two exceptions are retrieved), thus forcing retrieval
(when requested) from the target across resumptions in execution, and avoiding
the reporting of stale values.
Small addition change by Øyvind: change 'i' to unsigned to fix compiler
warning for xscale_debug_entry() fn.
Signed-off-by: Mike Dunn <mikedunn@newsguy.com> Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Alexander Stein [Wed, 8 Sep 2010 08:17:54 +0000 (10:17 +0200)]
Remove duplicated initialization
I a mail conversation with Øyvind we stated that speed may not be set at
all on case CLOCK_MODE_KHZ and CLOCK_MODE_RCLK. Also there isn't proper
error propagation adapter_khz_to_speed or jtag_rclk_to_speed.
So jtag_get_speed may need some rewrite for error propagation.
Wookey [Tue, 31 Aug 2010 12:53:50 +0000 (13:53 +0100)]
Numonyx M29W160ET patch
Someone called David Carne popped up on IRC and offered a fix (as he's not
on this list so can;t post here). I am just passing it on. (thanx David)
10:54 < davidc__> Basically; the Numonyx M29W160ET has an incorrect CFI PRI
block; it describes the erase blocks backwards
10:54 < davidc__> the linked patch has a fixup for that part [really trivial]:
Spencer Oliver [Wed, 25 Aug 2010 19:29:22 +0000 (20:29 +0100)]
cortex m3: add cortex_m3 reset_config cmd
This new cmd adds the ability to choose the Cortex-M3
reset method used.
It defaults to using SRST for reset if available otherwise
it falls back to using NVIC VECTRESET. This is known to work
on all cores.
Move any luminary specific reset handling to the stellaris cfg file.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
Spencer Oliver [Tue, 24 Aug 2010 19:50:20 +0000 (20:50 +0100)]
cfg: update Luminary config files
- Update all Luminary config's to use a common target/stellaris.cfg.
- Add Luminary ek-lm3s6965 config.
- Increase working area for boards with more ram.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
David Brownell [Fri, 27 Aug 2010 22:16:39 +0000 (15:16 -0700)]
bitq: unshadow pause()
bitq.c: In function ‘bitq_scan_field’:
bitq.c:224: error: declaration of ‘pause’ shadows a global declaration
/usr/include/unistd.h:429: error: shadowed declaration is here
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Ben Gardiner [Mon, 9 Aug 2010 18:41:56 +0000 (14:41 -0400)]
cfg: add omapl138 support and da850evm preliminary support
This patch adds support for the omapl138 target and preliminary support for the da850evm. The
target cfg file is based on the icepick routing done by the target/ti_dm6446.cfg file.
I have performed limited testing with this setup. I am posting this patch in the interest of
sharing cfg files and in the hopes that the experts on this list can correct errors I have made or
point out enhancements.
The testing I have performed is debugging uboot with gdb where I also use the following local.cfg
and gdbinit files. Debugging appears to work in so much as 'ni' works.
local.cfg:
gdb_memory_map disable
gdbinit:
target remote localhost:3333
set remote hardware-breakpoint-limit 2
set remote hardware-watchpoint-limit 2
monitor poll on
Øyvind Harboe [Sun, 8 Aug 2010 17:21:04 +0000 (19:21 +0200)]
arm7/9: fix "reset run + halt"
if polling is off, then "reset run + halt" would fail
since halt incorrectly assumed the target was in the
reset state as it is the internal poll implementation
that moves the sw tracking of the target state out
of the reset state.
To reproduce:
> reset run; halt
JTAG tap: zy1000.cpu tap/device found: 0x1f0f0f0f (mfg: 0x787, part: 0xf0f0, ver: 0x1)
BUG: arm7/9 does not support halt during reset. This is handled in arm7_9_assert_reset()
Mike Dunn [Mon, 2 Aug 2010 19:50:29 +0000 (12:50 -0700)]
xscale documentation: vector table handling
Hi everyone. I noticed some incorrect information in the user manual
regarding how the vector table is handled on the xscale, so for your
consideration, here's a short patch that corrects it, and adds a
little more detail I thought might be helpful.
The documentation states that OpenOCD does not attempt to synchronize
the vector tables in memory with those stored in the "mini instruction
cache". In fact, on each resume it does copy from memory to the cache
all entries in the high and low tables that were not previously
defined using the 'xscale vector_table' command. (In
src/target/xscale.c, see xscale_update_vectors(), which is invoked by
xscale_resume().) I take advantage of this during Linux boot-up. The
extra detail describes in general terms how I do this.
Corrections, comments are of course gratefully received.
Peter Stuge [Sun, 1 Aug 2010 01:26:47 +0000 (03:26 +0200)]
Remove srst_pulls_trst from LPC2148 target
srst_pulls_trst is only true on some (broken) LPC2148 boards, a fact
which is already documented in doc/openocd.texi, so it shouldn't be
set unconditionally in the target tcl.
This patch was needed to reflash when an Abort exception occured very
early after reset, before OpenOCD tried to halt the CPU.
David Brownell [Sun, 1 Aug 2010 06:27:14 +0000 (02:27 -0400)]
stellaris flash comment update
This flash driver works on more than just two chips.
(Though it does need work still, e.g. to protect more than 64K.
(On non-'3748-A0 chips where errata allow that.))
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
David Brownell [Mon, 19 Jul 2010 20:08:09 +0000 (16:08 -0400)]
more careful luminary init
Set up more of the Luminary-specific signals, and stop cloning
a few of the JTAG defaults. More comments too.
Still leaves the "dap info 0" bugs unresolved (presumably coupled
to this particular adapter family) where TPIU, ITM, DWT, and other
debug modules wrongly display as extra NVICs.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Spencer Oliver [Mon, 19 Jul 2010 11:22:18 +0000 (12:22 +0100)]
flash: add nuc910 nand driver
This adds a nand driver support for the nuc910 target.
Note that ECC is not currently supported by this driver, although
it is supported by the peripheral.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
David Brownell [Fri, 16 Jul 2010 23:22:15 +0000 (19:22 -0400)]
ARM ADI-V5: cleanup CID/PID addressing
Use addition for offsetting, not masking. Shorten some lines.
Make "component_start" print-only (unused otherwise; don't save).
Still doesn't resolve the issue where multiple components
are wrongly displaying as NVICs on some Cortex-M3 parts because
many PIDs appear to be zeroes ... maybe adapter related??
waiting for ZY1000 fifo to idle is now queued as
an asynchronous command. This radically improves
performance when waitIdle() is interspersed with
writes as no readback is required over TCP/IP.
projects / openocd / log