Paul Fertser [Fri, 23 May 2014 11:17:31 +0000 (15:17 +0400)]
target: reexamine after polling succeeds again
If polling was failing, it likely meant that either the target was
disconnected or rebooted. In the latter case it needs to be reexamined
to be properly configured for the debug session, so do it just in
case.
Reported-by: Tim Sander <tim@krieglstein.org> Tested-by: Tim Sander <tim@krieglstein.org>
Change-Id: I5b067c18d9276d4e86cc59739f196ae7d0931622 Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2151 Tested-by: jenkins Reviewed-by: Tim Sander <tim@krieglstein.org> Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Move logging for cmsis_dap_queue_ap_read/write to happen after a call
to cmsis_dap_ap_q_bankselect so that that SWD operation would appear
in the log in the same sequence they happen on the bus.
arm_adi_v5: Do not ignore register polling timeout
Previous to this commit 'ahbap_debugport_init' would ignore if timeout
happened or not when waiting for CDBGPWRUPACK and CSYSPWRUPACK and would
continue initialization regardless. It also would not reset the
timeout counter after finishing polling for CDBGPWRUPACK and starting
for CSYSPWRUPACK which could potentially cause some problems.
Also refactor code of both snippets into a more generic function to
avoid duplication.
Ivan De Cesaris [Wed, 21 May 2014 13:20:08 +0000 (15:20 +0200)]
quark_x10xx: cleanup of LOG format specifiers
Fix for LOG format specifiers, this is a superset of those
exposed by the arm-none-eabi build.
Add 0x prefix for all values printed in hex.
Add LOG messages for error cases when enabling or disabling
paging.
Change-Id: I070c556e0ad31204231a2b572e7b93af22a9bc61 Signed-off-by: Ivan De Cesaris <ivan.de.cesaris@intel.com>
Reviewed-on: http://openocd.zylin.com/2149 Tested-by: jenkins Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Aurelien Jacobs [Wed, 18 Dec 2013 23:17:49 +0000 (00:17 +0100)]
lpcspifi: setup a valid stack pointer before calling ROM code using stack
The spifi_init_code blob is calling the spifi_init() function from the ROM.
This ROM function is making use of the stack. So if the stack pointer is
invalid, trying to execute this code leads to a double fault and the
target_run_algorithm() call return with an error.
This patch simply ensure that the stack pointer is properly setup before
calling the spifi_init() ROM function.
Yegor Yefremov [Mon, 5 May 2014 15:36:27 +0000 (17:36 +0200)]
KS869x: add new target
This patch adds Micrel's KS869x target. The configuration was taken from
http://www.mmnt.net/db/0/0/www.micrel.com/ethernet/8695 - Micrel's
FTP server i.e. their OpenOCD 7.0 package.
The only change compared to the original file is the removal of
reset configuration, as it belongs to the board configuration.
Andrey Smirnov [Sat, 8 Mar 2014 22:42:28 +0000 (14:42 -0800)]
kinetis: Revise CPU un-securing code
Old version of the code had several problems, among them are:
* Located in a generic ADI source file instead of some Kinetis
specific location
* Incorrect MCU detection code that would read generic ARM ID
registers
* Presence of SRST line was mandatory
* There didn't seem to be any place where after SRST line assertion
it would be de-asserted.
* Reset was asserted after waiting for "Flash Controller Ready" bit
to be set, which contradicts official programming guide AN4835
* Mass erase algorithm implemented by that code was very strange:
** After mass erase was initiated instead of just polling for the
state of "Mass Erase Acknowledged" bit the code would repeatedly
initiate mass erase AND poll the state of the "Mass Erase
Acknowledged"
** Instead of just polling for the state of "Flash Mass Erase in
Progress"(bit 0 in Control register) to wait for the end of the
mass erase operation the code would: write 0 to Control
register, read out Status register ignoring the result and then
read Control register again and see if it is zero.
* dap_syssec_kinetis_mdmap assumed that previously selected(before
it was called) AP was 0.
This commit moves all of the code to kinetis flash driver and
introduces three new commands:
o "kinetis mdm check_security" -- the intent of that function is to be used as
'examine-end' hook for any Kinetis target that has that kind of
JTAG/SWD security mechanism.
o "kinetis mdm mass_erase"" -- This function removes secure status from
MCU be performing special version of flash mass erase.
o "kinetis mdm test_securing" -- Function that allows to test securing
fucntionality. All it does is erase the page with flash security settings thus
making MCU 'secured'.
New version of the code implements the algorithms specified in AN4835
"Production Flash Programming Best Practices for Kinetis K-
and L-series MCUs", specifically sections 4.1.1 and 4.2.1.
It also adds KL26 MCU to the list of devices for which this security
check is performed. Implementing that algorithm also allowed to simplify
mass command in kinetis driver, since we no longer need to write security
bytes. The result that the old version of mass erase code can now be
acheived using 'kinetis mdm mass_erase'
Tested on accidentally locked FRDM-KL26Z with KL26 Kinetis MCU.
Change-Id: Ic085195edfd963dda9d3d4d8acd1e40cc366b16b Signed-off-by: Andrey Smrinov <andrew.smirnov@gmail.com>
Reviewed-on: http://openocd.zylin.com/2034 Tested-by: jenkins Reviewed-by: Paul Fertser <fercerpav@gmail.com> Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Salvador Arroyo [Tue, 3 Dec 2013 22:25:20 +0000 (23:25 +0100)]
mips32: new code for pracc exec
This is only the basic code proposed for mips32_pracc_exec() function.
It checks every pracc address against the expected address when
reading (instruction fetch).
The code expects to start at PRACC_TEXT and any subsequent read address
is obtained by adding 4 to the previous one.
After shifting out all the instructions the code executes a final check.
It checks now for the first pass trough PRACC_TEXT and shift out
only NOP instructions.
A mips core does not need an additional NOP and after the first check
it exits if there is no store access pending.
After shifting out one NOP the core must be reading at pracc text or the
code exits with error.
The code continues shifting out NOPs until all store accesses have
been performed.
After shifting out 10 NOPs it exits with error.
No assumption is made about the number of store instruction shifted out or
the ordering of the store accesses. It only checks that the number of
store accesses is the same as the number of store instructions at dmseg
after execution.
mips32_pracc_read_ctrl_addr() and mips32_pracc_finish() are added to
simpify a bit the code. Fields pa_ctrl and pa_addr are added
in ejtag_info for storing values of pracc control and address.
Salvador Arroyo [Sun, 1 Dec 2013 09:40:34 +0000 (10:40 +0100)]
mips32: cleanups in legacy pracc code
This is the first patch intended to make a more precise pracc check
when running in legacy mode (code executed by mips32_pracc_exec()).
It only makes some cleanups, mostly due to unnecessary code.
With the last cache optimizations for processor access (pa for short)
all the pracc functions generate the code following some rules that
make pa more easily to check:
There are no load instructions from dmseg. All the read pas are
instruction fetches. PARAM_IN related stuff is not needed.
Registers are restored either from COP0 DeSave or from ejtag
info fields. PRACC_STACK related stuff is not needed any more.
The code starts execution at PRACC_TEXT and there are no branch or jump
instruction in the code, apart from the last jump to PRACC_TEXT.
The fetch address is ever known.
For every store instruction to dmseg the function code sets
the address of the write/store pa.
The address of every store pa is known.
Current code ends execution when reading a second pass through PRACC_TEXT.
This approach has same inconveniences:
If the code starts in the delay slot of a jump it makes a jump
to PRACC_TEXT after executing the first instruction. A second pass
through PRACC_TEXt is read and the function exits without any warning.
This seems to occur sometimes when a 24kc core is halted in the delay
slot of a branch.
If a debug mode exception is triggered during the execution of a
function the core restarts execution at PRACC_TEXT. Again the function
exits without any warning.
If for whatever reason the core starts fetching at an unexpected
address the code now sends a jump instruction to PRACC_TEXT, but due
to the delay slot the core continues fetching at whatever address + 4
and a second jump instruction will be send for execution. The result
of a jump instruction in the delay slot of another jump is
UNPREDICTABLE. It may work as expected (ar7241), or let the core in
the delay slot of a jump to PRACC_TEXT for example. This means the
function called next may also fail (pic32mx).
Salvador Arroyo [Sun, 25 Aug 2013 10:21:18 +0000 (12:21 +0200)]
mips: use cp0 DeSave to cache $15 / t7
Near all pracc functions store $15 in DeSave and
restore it when exiting.
There is no need to save it, if mips32_pracc_read_regs()
save this register in Desave when entering debug mode.
mips32_pracc_write_regs() needs to update it when
exiting debug mode.
Other pracc functions must not modify DeSave.
The jump code in the fastdata transfer function needs also
some little modifications.
Remark:
Like in current code the user can read/modify $15
with the cp0 31 commands.
Change-Id: I5b7dfc1b6169da846f5d2dd3ad4209a9da2c3fad Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es>
Reviewed-on: http://openocd.zylin.com/1565 Tested-by: jenkins Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com> Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Salvador Arroyo [Sat, 24 Aug 2013 12:18:09 +0000 (14:18 +0200)]
mips: load fast data transfer handler code with mips32_pracc_write_mem()
Currently the code is loaded calling mips32_pracc_write_mem_generic().
Cache synchronization is not performed.
If configured as write back cache there is no chance to execute the
handler. If configured as write through cache and the cache
lines written to are not cache resident (I-side cache miss) may work.
The patch makes possible to execute the handler in a cached active
memory segment (mainly from KSEG0), but nothing else. The data
is still loaded without performing cache synchronization, code loaded
may not be executable.
Performance may not be faster. At start, for example, the code resides in
main memory, not in cache, and the core must transfer code from
memory. We can really modify the code to force a wait for the first
transfer like we do with start and end addresses, making sure the code
is cache resident for the rest of the queued transfers.
This can also may happen if we execute code (greater than the I cache size)
and the handler code is evicted from the cache.
Code tested on ar7241.
Change-Id: Iffdb4dae108b872fef0e7bacc5ea99649cdc1630 Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es>
Reviewed-on: http://openocd.zylin.com/1564 Tested-by: jenkins Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com> Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Salvador Arroyo [Fri, 23 Aug 2013 16:50:43 +0000 (18:50 +0200)]
mips: load code in buffer mode
Currently the functions mips32_checksum_memory() and mips32_blank_check_memory()
load the code word by word.
The bug in cache code is a good reason for doing so.
If there is no other reason we can load the code as a buffer to save time.
mips_m4k_write_memory() expect a buffer in target endianness, this is done by
target_buffer_set_u32_array().
Cleaned up exit code.
Tested on ar7241 big endian and pic32mx little endian with verify_image.
Flash erase check only tested in pic32mx.
Change-Id: Ib63ed98732b2e23b058e7349a0a57934b7604905 Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es>
Reviewed-on: http://openocd.zylin.com/1562 Tested-by: jenkins Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Paul Fertser [Mon, 28 Apr 2014 10:34:47 +0000 (14:34 +0400)]
Update to the current Jim Tcl
This is a post-release version but hopefully some fixes that went in
are worth it; also the changes here make OpenOCD compatible with stock
0.75 version if a distro maintainer decides to use it.
Kamal Dasu [Tue, 3 Dec 2013 21:15:42 +0000 (16:15 -0500)]
svf: Fix debug and error messages that print hex buffer
Added SVF_BUF_LOG macro to properly print the hex buffer of parsed
string for SIR, SDR, TDI, TDO and MASK. The original debug and error
logs with respect to printing real values were misleading and also
had endianess issues. All the bits are printed now instead of just
u32 values.
Change-Id: Ie89902403bdb61ff458418446c2ca1253ea2a63f Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Reviewed-on: http://openocd.zylin.com/1964 Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com> Tested-by: jenkins
Ash Charles [Thu, 17 Apr 2014 00:32:23 +0000 (17:32 -0700)]
Add support for Gumstix AeroCore device
The Gumstix AeroCore board [1] contains a STM32F427 microcontroller.
Schematics for this board will also be made available [2].
The JTAG interface for this chip can be accessed via a USB connection
provided by an FTDI chip (0403:6011).
Ivan De Cesaris [Fri, 18 Apr 2014 09:19:40 +0000 (11:19 +0200)]
quark_x10xx: fix IO r/w operations with paging enabled
Paging checking and disabling wasn't present for IO r/w,
so the commands were successful only when paging wasn't
enabled (e.g. EFI boot phase).
Change-Id: I41366c0fadff3ea1eb8a153291f20a46cd9ddec1 Signed-off-by: Ivan De Cesaris <ivan.de.cesaris@intel.com>
Reviewed-on: http://openocd.zylin.com/2118 Tested-by: jenkins Reviewed-by: Peter Stuge <peter@stuge.se> Reviewed-by: Paul Fertser <fercerpav@gmail.com>
The TI TMS470 and TMS570 series of processors are BE-32 processors,
despite BE-32 not being supported by ARM in the Cortex-R4 core. TI
hacked in BE-32 support, which requires odd swizzling in OpenOCD to
make memory reads and writes function correctly. In particular,
without this change, OpenOCD word reads and writes had the bytes
reversed, and halfword and byte packed reads were reading garbage.
In my testing, this change fixes these problems.
Change-Id: I21dd30f4b9003f20fcc85f674ab833407bb61f74 Signed-off-by: Seth LaForge <sethml@google.com>
Reviewed-on: http://openocd.zylin.com/2064 Tested-by: jenkins Reviewed-by: Paul Fertser <fercerpav@gmail.com> Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Paul Fertser [Sat, 12 Apr 2014 13:22:00 +0000 (17:22 +0400)]
mips32, dsp563xx: fix segfault on Gdb attach
Since c6216201b249e6a97fcc085e413e3d34e0de6fb7 gdb target description
generation support is enabled by default and it counts on checking
"feature" pointer in reg_list. Both mips32 and dsp563xx neither used
calloc nor explicitly set feature (as it was a newly introduced struct
field).
This patch changes all targets to use calloc for consistency.
Change-Id: I9eceadef8b04aacb108e24ae23cb51ca3009586f Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2102 Tested-by: jenkins Reviewed-by: Salvador Arroyo <sarroyofdez@yahoo.es> Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Paul Fertser [Sun, 6 Apr 2014 04:36:37 +0000 (08:36 +0400)]
jtag/drivers/remote_bitbang: use sizeof to determine maximum unix socket path length
Different *nix systems use different constants, so sizeof should be
used instead. This fixes the build on OS X (as sun_path length is
hardcoded to 104 on Darwin).
Tim Sander [Mon, 31 Mar 2014 20:21:44 +0000 (21:21 +0100)]
target: fix incorrect arm cpu monitor mode encoding
According to the "Arm Arch Ref Manual ARMv7-a and ARMv7-R edition" the
CPSR encoding for Monitor mode is 0b10110 (22) not 0b11010 (26) as is
currently used.
Andrey Smirnov [Mon, 10 Feb 2014 16:06:04 +0000 (08:06 -0800)]
at91smad: Fixes to 'samd_protect'
Some fixes to 'samd_protect' including:
- Fix a bug in which the value of 'set' parameter passed into the
function was ignored so it was impossible to remove flash
protection once it was set.
- Check the protection status of the sector via 'is_protected'
field of the corresponding 'flash_sector' structure to see if
any actual HW manipulations needs to be done.
- Change the way the errors during protection activation are
handled. Now even in the case of error in the middle of
protecting a number of sectors the subroutine would still update
the state of the sector protection in sectors array so as to
avoid cases where openocd thinks that the sector is not protected
while it actually is.
Paul Fertser [Sat, 22 Mar 2014 12:47:37 +0000 (16:47 +0400)]
tcl: introduce init_target_events and use it for gdb flashing events
This introduces a new global Tcl procedure that is run just after
init_targets and before init_boards.
Its default behaviour is to assign gdb-flash-erase-start and
gdb-flash-write-end to reasonable defaults.
The rationale for doing "reset init" before gdb erases and flashes
memory is that all flash drivers are written in assumption that they
can safely be used only after chip reset (plus chip-specific
configuration in the init handler if any). The need to use "reset
halt" after flashing is because a user expects running firmware after
loading to be the same as running it from power-on-reset.
Change-Id: I9ddc4047611904ca4ca779b73376d2739611948a Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2062 Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Paul Fertser [Mon, 27 Jan 2014 18:25:42 +0000 (22:25 +0400)]
Add xscale debug helper sources and everything related to dist
GPL requires providing sources for any derived work. I do not see any
reason to not include the xscale stuff into release tarballs.
Wildcard matching is used because plain directory name matches
implicit rule for executables and xscale.c built is errorneously
attempted, and directory name with a slash duplicates a directory
(xscale/xscale) in dist.
Change-Id: Ie0266470dcb97be87a09ba2dda9b3957f7cbc2fa Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1911 Tested-by: jenkins Reviewed-by: Robert Jarzmik <robert.jarzmik@free.fr> Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Spencer Oliver [Mon, 17 Mar 2014 14:15:41 +0000 (14:15 +0000)]
rtos: fix xml register support regression
Seems that when xml register support was added the rtos code was not
updated to match. This then caused gdb to return the following error when
rtos support was enabled - "Remote 'g' packet reply is too long".
Change-Id: I7429c4b1efed120e2e690678d55f3d6e87ee1ff1 Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/2054 Tested-by: jenkins Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Andrey Smirnov [Sat, 15 Mar 2014 17:40:23 +0000 (10:40 -0700)]
nrf51: Fix incorrect flash writing sequence
nRF51 doesn't have any sort of flash page cache so we need to write
all of the data on the word-by-word basis and poll for "Flash Ready"
bit each time.
Andrey Smirnov [Sat, 1 Mar 2014 21:40:08 +0000 (13:40 -0800)]
nrf51: Add UICR writing support
SoftDevice stack ihex binary, provided by Nordic expects being able to
write data necessary for its correct operation at the adresses inside UICR.
This patch exposes UICR region of flash as a second bank on the MCU to
facilitate that.
Andrey Smirnov [Fri, 28 Feb 2014 19:35:16 +0000 (11:35 -0800)]
nrf51: Add a known devices table and simple chip type detection code
Unfortunately due to my oversight, the original version of the
nrf51_probe function contained useless code that read the contents of
DEVICEID[0] an DEVICEID[1] registers and did nothing about it(those
registers had nothing to do with the device type information anyway).
This commit fixes that code by changing its behavior to read the HWID
field of CONFIGID register and looking up the corresponding device
information in the know devices table. This information is useful
when choosing the versions of SDK and SoftDevice for the chip
using "nRF51822 compatibility matrix".
Andrey Smirnov [Wed, 19 Mar 2014 15:20:36 +0000 (08:20 -0700)]
armv7m: Do not ignore 'value' parameter in armv7m_write_core_reg
Ignoring the value parameter in that function makes its code rather
misleading. Also the only caller of it, armv7m_restore_context already
does the whole "buf_get_u32" conversion business, so using
'value' also removes the waste of doing the conversion twice.
Andrey Yurovsky [Sat, 8 Mar 2014 01:16:52 +0000 (17:16 -0800)]
jlink: add support for Jlink-OB (0x0105) devices
The JLink-OB (onboard) devices work the same way as the normal JLink
except that their PID is 0x0105 (and that's the only one we know of so
far) and their endpoint addresses are different due to there being a
CDC-ACM interface as well. These JLink-OB devices show up on a lot of
vendors' development kits as an integrated debugger.
This change simply checks whether the adapter we opened has a JLink-OB
PID and, if it does, uses the JLink-OB endpoints rather than the
default. To do this, we add a new routine, jtag_libusb_get_pid() to the
libusb adapter layer, it in turn just calls
libusb_get_device_descriptor(), which previously had no wrapper.
Also, checkpatch.pl doesn't like the VID/PID macros as defined so I
moved them to the array itself. This should have no effect on the code.
This change adds the 0102 through 0104 PIDs to openocd.rules as well as this
new 0105 PID.
Tested on an Atmel SAM4S Xplained board which has a JLink-OB, also
regression tested by using a 0x0101 PID normal JLink adapter.
Change-Id: I5ebc924ab66c86f1902942bebc203a34d97abc64 Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/1899 Reviewed-by: Paul Fertser <fercerpav@gmail.com> Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk> Tested-by: Spencer Oliver <spen@spen-soft.co.uk>
instead of replicating icepick_d_tapenable in many of TI's newer
platforms, we can move to icepick.cfg and just call it from board TCL
configuration file. This is similar to the C but has a few changes we
need to make.
Change-Id: I0ab48005ccd66cd5b67b919fb5e3b462288f211d Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Tom Rini <trini@ti.com>
Reviewed-on: http://openocd.zylin.com/2030 Tested-by: jenkins Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Jörg Wunsch [Fri, 14 Mar 2014 13:41:51 +0000 (14:41 +0100)]
CMSIS-DAP: print a debug message when the USB product string cannot be read
As suggested by Stian Skjelstad in a comment in:
http://openocd.zylin.com/#/c/2044/
if the USB product string cannot be read, provide a debug message so
users might get aware of a potential permission problem when looking
at the debug output.
Jörg Wunsch [Fri, 14 Mar 2014 10:29:24 +0000 (11:29 +0100)]
Make the Atmel SAM3 family SWD-aware
Atmel's SAM3 and SAM4 processor families are very close to each other
in many respects. However, so far, only the SAM4 target script
contained the magic to allow using SWD, while SAM3 was tied to JTAG
only. This e.g. prevented the CMSIS-DAP driver from accessing SAM3
devices as it only uses SWD transport (by now).
The patch pulls all the things from the SAM4 target script that are
also applicable to SAM3 devices. With the patch, an Atmel CMSIS-DAP
debugger (Atmel-ICE) was proven to be able to successfully attach to a
SAM3S-EK evaluation kit. I also cross-checked that accessing through
a SAM-ICE (Segger J-Link) still works with the patch.
Jörg Wunsch [Fri, 14 Mar 2014 10:00:54 +0000 (11:00 +0100)]
All Atmel-provided CMSIS-DAP devices use 512 byte packet size
The existing CMSIS-DAP driver matches the USB VID/PID against 0x3eb
(Atmel VID) and 0x2111 (Atmel EDBG embedded CMSIS-DAP debugger), and
then bumps the packet size from its default of 64 to 512. However, it
turned out that *all* Atmel-provided CMSIS-DAP devices (EDBG with PID
0x2111; JTAGICE3 with firmware version 3.x, PID 0x2140; new Atmel-ICE
[successor of JTAGICE3], PID 0x2141) require a 512-byte packet size.
Obviously, all run the same USB implementation inside their custom
microcontroller. Thus, it seems best to simply assume that *all*
Atmel CMSIS-DAP devices use this packet size, and don't check the PID
at all.
Jörg Wunsch [Fri, 14 Mar 2014 09:50:36 +0000 (10:50 +0100)]
Prevent segfault when the USB product string cannot be retrieved
In the CMSIS-DAP driver, if nothing has been specified by the user, an
attempt is made to find the first device with the (mandatory)
substring "CMSIS-DAP" in any USB device's product string. However,
while (usually) all devices can be traversed, devices the user does
not have permission for cannot be read the product string from,
resulting in a NULL pointer. Trying to find the substring "CMSIS-DAP"
causes a segementation fault then.
Jens Hoffmann [Sun, 9 Mar 2014 09:42:09 +0000 (10:42 +0100)]
stm32f2x.c: Add STM32F401xE device id.
Nucleo F401 board uses STM32F401RE chip with new device id and
got more flash than existing devices (512K). This patch adds
new the identifier to probe functions so flashing will now work.
projects / openocd / log