Rolf Meeser <rolfm_9dq@yahoo.de>
This patch adds target algorithm support for those flash devices that do not support DQ5 polling. So far they could only be programmed with host algorithm, but this was way too slow.
David Brownell <david-b@pacbell.net>
Optionally shave time off the armv4_5 run_algorithm() code: let
them terminate using software breakpoints, avoiding roundtrips
to manage hardware ones.
Enable this by using BKPT to terminate execution instead of "branch
to here" loops. Then pass zero as the exit address, except when
running on an ARMv4 core. ARM7TDMI, ARM9TDMI, and derived cores
now set a flag saying they're ARMv4.
Use that mechanism in arm_nandwrite(), for about 3% speedup on a
DaVinci ARM926 core; not huge, but it helps. Some other algorithms
could use this too (mostly flavors of flash operation).
David Brownell <david-b@pacbell.net>
Fix docs on ARM11 MCR and MRC coprocessor commands:
correct read-vs-write; and describe the params.
(ARM920 and ARM926 have cp15-specific commands; this
approach is more generic. MCR2, MRC2, MCRR, MCRR2,
MRRC, and MRRC2 instructions could also get exposed.)
David Brownell <david-b@pacbell.net>
Provide an "armv7a disassemble" command. Current omissions include
VFP (except as coprocessor instructions), Neon, and various Thumb2
opcodes that are not available in ARMv7-M processors.
David Brownell <david-b@pacbell.net>
lean up some loose ends with the ARM disassembler
- Add a header comment describing its current state and uses
and referencing the now-generally-available V7 arch spec
- Support some mode switch instructions:
* Thumb to Jazelle (BXJ)
* Thumb to ThumbEE (ENTERX)
* ThumbEE to Thumb (LEAVEX)
- Improve that recent warning fix (and associated whitespace goof)
- Declare the rest of the internal code and data "static". A
compiler may use this, and it helps clarify the scope of these
routines (e.g. what changes to them could affect).
Matt Hsu <matt@0xlab.org> This patch simply enables the halting debug mode.
By enabling this bit, the processor halts when a debug event
such as breakpoint occurs.
Abstract the orion_nand_fast_block_write() routine into a separate
routine -- arm_nandwrite() -- so that other ARM cores can reuse it.
Have davinci_nand do so. This faster than byte-at-a-time ops by a
factor of three (!), even given the slowish interactions to support
hardware ECC (1-bit flavor in that test) each 512 bytes; those could
be read more efficiently by on-chip code.
NOTE that until there's a generic "ARM algorithm" structure, this
can't work on newer ARMv6 (like ARM1136) or ARMv7A (like Cortex-A8)
cores, though the downloaded code itself would work just fine there.
oharboe [Sun, 30 Aug 2009 17:27:50 +0000 (17:27 +0000)]
David Brownell <david-b@pacbell.net> Be sure the built-in search paths always go *after* ones provided
on the command line ... matching comment in add_default_dirs().
Without this it's impossible to use a private config file which
happens to have the same name as an installed one. Say, because
you're bugfixing a private copy...
Compile-tested. This might not set up the simulator right for the
ARMv6 single step support; only BXJ branches though, and docs to
support Jazelle branching are non-public (still, sigh).
ARMv6 instructions known to be mis-handled by this disassembler
include: UMAAL, LDREX, STREX, CPS, SETEND, RFE, SRS, MCRR2, MRRC2
oharboe [Thu, 27 Aug 2009 10:37:01 +0000 (10:37 +0000)]
arm11 hardware step using simulation + breakpoint. Use "hardware_step enable" command to revert to hardware stepping. Ideally we could retire the "hardware_step enable" command once we no longer believe it to be necessary.
oharboe [Wed, 26 Aug 2009 19:23:35 +0000 (19:23 +0000)]
Matt Hsu <matt@0xlab.org> and Holger Hans Peter Freyther <zecke@selfish.org> Only dap_ap_select when we are going to do a memory access
in the fast reg case.
oharboe [Wed, 26 Aug 2009 19:21:26 +0000 (19:21 +0000)]
Matt Hsu <matt@0xlab.org> cortex_a8_exec_opcode is writing the ARM instruction into
the ITR register but it will only be executed when the DSCR[13]
bit is set. The documentation is a bit weird as it classifies
the DSCR as read-only but the pseudo code is writing to it as
well. This is working on a beagleboard.
oharboe [Wed, 26 Aug 2009 19:20:25 +0000 (19:20 +0000)]
Matt Hsu <matt@0xlab.org> Wait for the DTRRX to be full before reading it. Remove the trans_mode change as it is done in the mem_ap_read_atomic_u32 function.
oharboe [Wed, 26 Aug 2009 19:16:08 +0000 (19:16 +0000)]
Matt Hsu <matt@0xlab.org> and Holger Hans Peter Freyther <zecke@selfish.org> Before executing a new instruction wait for the previous
instruction to be finished. This comes from the pseudo code
of the cortex a8 trm.
oharboe [Wed, 26 Aug 2009 19:06:56 +0000 (19:06 +0000)]
David Brownell <david-b@pacbell.net> Fix segv in jtag_examine_chain(): exit loop on no-tap. Keep
"next iteration" step with the rest of the loop overhead.
Cleanup: remove spurious whitespace, and an overlong line;
only assign "tap->hasidcode" once.
oharboe [Wed, 26 Aug 2009 06:26:29 +0000 (06:26 +0000)]
David Brownell <david-b@pacbell.net> Clock updates/fixes for the Stellaris flash driver:
- Bugfixes:
* internal osc: it's *12* MHz (not 15 MHz) on _current_ chips
+ except new Tempest parts where it's 16 MHz (and calibrated!)
+ or some old Sandstorm ones, where 15 MHz was valid
* crystal config:
+ read and use the crystal config, don't assume 6 MHz
+ know when that field is 4 bits vs 5
* an RCC2 register may be overriding the original RCC
+ more clock source options
+ bigger dividers
+ fractional dividers on Tempest (NYET handled)
* there's a 30 KHz osc on newer chips (for deep sleep)
* there's a 32768 Hz osc on newer chips (for hibernation)
- Cosmetic
* say "rev A0" not "vA.0", to match vendor docs
* don't always report master clock as an "estimate":
+ give the error bound if it's approximate, like "±30%"
+ else don't say anything
* fix whitespace and caps in some messages
* these are not AT91SAM chips!!
Those clock issues might explain problems sometimes reported when
writing to Stellaris flash banks; they affect write timings.
That 12-vs-15 MHz issue is problematic; there's no consolidated doc
showing which chips (and revs!) have which internal oscillator speed.
It's clear that only older silicon had the faster-and-less-accurate
flavor. What's less clear is which chips are "old" like that.
oharboe [Tue, 25 Aug 2009 20:02:19 +0000 (20:02 +0000)]
David Brownell <david-b@pacbell.net> Tweak disassembly commands:
For ARMv4/ARMv5:
- better command parameter error checking
- don't require an instruction count; default to one
- recognize thumb function addresses
- make function static
- shorten some too-long lines
For Cortex-M3:
- don't require an instruction count; default to one
With the relevant doc updates.
---
Nyet done: invoke the thumb2 disassembler on v4/v5,
to better handle branch instructions.
oharboe [Tue, 25 Aug 2009 19:59:55 +0000 (19:59 +0000)]
David Brownell <david-b@pacbell.net> More jtag_add_reset() cleanup:
Unify the handling of the req_srst parameter, and rip out a
large NOP branch and its associated FIXME. (There didn't seem
to be anything that needs fixing; but that was unclear since
the constraints were scattered all over the place not unified.)
oharboe [Tue, 25 Aug 2009 19:58:06 +0000 (19:58 +0000)]
David Brownell <david-b@pacbell.net> More jtag_add_reset() cleanup:
Unify the handling of the req_tlr_or_trst parameter. Basically,
JTAG TMS+TCK ops ("TLR") is always used ... unless TRST is a safe
option in this system configuration.
oharboe [Tue, 25 Aug 2009 19:55:32 +0000 (19:55 +0000)]
David Brownell <david-b@pacbell.net> Some jtag_add_reset() cleanup:
- Track whether TRST and/or SRST actually change:
* If they're not changing, don't ask the JTAG adapter to do anything!
(JTAG TCK/TMS ops might still be used to enter TAP_RESET though.)
* Don't change their recorded values until after the adapter says it
did so ... so fault paths can't leave corrupt state.
* Detect and report jtag_execute_queue() failure mode
* Only emit messages saying what really changed; this includes adding
an omitted "deasserted TRST" message.
* Only apply delays after deasserting SRST/TRST if we *DID* deassert!
- Messages say "TLR" not "RESET", to be less confusing; there are many
kinds of reset. (Though "TLR" isn't quite ideal either, since it's
the name of the TAP state being entered by TMS+TCK or TRST; it's at
least non-ambiguous in context.)
So the main effect is to do only the work this routine was told to do;
and to have debug messaging make more sense.
oharboe [Tue, 25 Aug 2009 19:52:02 +0000 (19:52 +0000)]
David Brownell <david-b@pacbell.net> Accomodate targets which don't support various target-specific
reset operations. Maybe they can't; or it's a "not yet" thing.
Note that the assert/deassert operations can't yet trigger for
OMAP3 because resets currently include JTAG reset in all cases,
resetting the ICEpick and thus disabling the TAP for Cortex-A8.
oharboe [Tue, 25 Aug 2009 07:17:19 +0000 (07:17 +0000)]
strange.... the code build and links w/Linux GCC target but fails w/arm-elf. The code was clearly broken as it was missing two extern's in the .h file...
oharboe [Tue, 25 Aug 2009 07:09:48 +0000 (07:09 +0000)]
Michael Schwingen <rincewind@discworld.dascon.de> The attached patch adds a "xscale vector_table" command that allows to set
the values that are written in the mini-IC (plus documentation updates that
describe why this is needed).
oharboe [Tue, 25 Aug 2009 07:04:25 +0000 (07:04 +0000)]
Audrius Urmanavičius <didele.deze@gmail.com> Latest source (R2606) does not compile under Windows+Cygwin - fails with error about possibly uninitialized use of variable 'ch'.
oharboe [Tue, 25 Aug 2009 06:58:34 +0000 (06:58 +0000)]
David Brownell The rest of the Cortex-A8 support from Magnus: replace the previous
nonfunctional cortex_a8 code with something that at least basically
works (for halt/step/resume, without MMU) even if it is incomplete.
(With tweaks from Øyvind, and cleanup from Dave.)
This code has mainly been developed and tested against R1606, it has
been built and tested against R2294 where it runs but step and resume
commands are broken due to regression (which should be fixed now).
This code is really written for OMAP3530. It doesn't identify debug
resources using generic DAP calls to scan the ROM table, or perform
topology detection. The OMAP3530 DAP exposes two memory access ports:
- Port #0 is connected to L3 interconnect (the main bus) with
passthrough to the L4 EMU bus ... so it will be used for most
memory accesses.
- Port #1 is connected to a dedicated debug bus (L4 EMU), with
access to L4 Wakeup, and holds the ROM table ... so it must
be used for most debug and control operations.
The are some defines to handle this in cortex_a8.c, which should be
replaced with more general code. Having access to another Cortex-A8
implementation would help get that right.
oharboe [Tue, 25 Aug 2009 06:57:26 +0000 (06:57 +0000)]
David Brownell Subset of Cortex-A8 support from Magnus: create an armv7a file
and seed it with DAP access support using the current ADIv5 code.
(With tweaks and cleanup from Øyvind and Dave.)
The ARMv7-AR architecture manual is not publicly available (even
in subset form like the ARMv7-M spec), so it's hard to distinguish
between the Cortex-A8 implementation and the ARMv7-A architecture.
The register set presumably is architectural, and so it's stored
here; it's like earlier ARMs, with small additions. Ditto the
instruction set, though Thumb2 support is used (extending Thumb
support from ARMv6 with more 32-bit instructions) and there's this
ThumbEE thing too. There is a new "debug monitor" mode, not yet
fully addressed here, to support debugging in environments (like
motor control) where halting debug mode is inadvisable.
oharboe [Mon, 24 Aug 2009 07:26:05 +0000 (07:26 +0000)]
Jonas Horberg <jhorberg@sauer-danfoss.com>
The trunk is currently broken for interfaces without
the speed_div function (interface specific clock speed
value to kHz conversion). Example: parport.
oharboe [Thu, 20 Aug 2009 08:55:34 +0000 (08:55 +0000)]
Piotr Ziecik <kosmo@semihalf.com> This patch adds handling blank characters between hex digits in
SVF file, making OpenOCD compatible with files generated by
Altera Quatrus II 9.0.
ntfreak [Thu, 20 Aug 2009 07:54:49 +0000 (07:54 +0000)]
- remove enable-ft2232-highspeed configure option, high speed ftdi support is now detected during the configure stage
- warning now issued if high speed ftdi device found and openocd was built using an old driver
oharboe [Thu, 20 Aug 2009 07:15:46 +0000 (07:15 +0000)]
David Brownell <david-b@pacbell.net>More Thumb2 disassembly:
ARMv7-M: A5.3.6 Load/store dual or exclusive, table branch
GCC will generate the table branch instructions, usually with inlined
tables that will confuse this disassembler. LDREX and STREX are not
issued by GCC without inline assembly.
This means all Thumb2 instructions implemented by Cortex-M3 can now
be disassembled. Cortex-A8 cores support more Thumb2 instructions,
but most of those aren't yet publicly documented.
projects / openocd / log