From 145dbc02501bba43cfee952d5669406c871be6d8 Mon Sep 17 00:00:00 2001 From: Shaohui Xie Date: Thu, 28 Jun 2012 23:37:25 +0000 Subject: [PATCH] powerpc/p2041: configure the CPLD lane_mux according to RCW Lane muxing on p2041 is controlled by a reg in CPLD, offset of this reg is 0xc, CPLD supports SATA by default, we should re-configure the lane muxing according to RCW, which indicates what SerDes protocol it is running. Default lane muxing map is as below: Lane G on bank1 routes to SGMII, controlled by bit 1 of the reg; Lane A on bank2 routes to AURORA, controlled by bit 0 of the reg; Lane C/D on bank2 routes to SATA0 and SATA1, controlled by bit 2 and bit 3 respectively. Default value of these bits for lane muxing is '1', we should set or clear these bits accoring to RCW. Signed-off-by: Shaohui Xie Acked-by: Timur Tabi Signed-off-by: Andy Fleming --- board/freescale/p2041rdb/eth.c | 39 ++++++++++++++++++++++++++++++++++ 1 file changed, 39 insertions(+) diff --git a/board/freescale/p2041rdb/eth.c b/board/freescale/p2041rdb/eth.c index 4b0d577e2c..fec97773ea 100644 --- a/board/freescale/p2041rdb/eth.c +++ b/board/freescale/p2041rdb/eth.c @@ -136,6 +136,11 @@ void board_ft_fman_fixup_port(void *fdt, char *compat, phys_addr_t addr, } #endif /* #ifdef CONFIG_FMAN_ENET */ +#define CPLD_LANE_A_SEL 0x1 +#define CPLD_LANE_G_SEL 0x2 +#define CPLD_LANE_C_SEL 0x4 +#define CPLD_LANE_D_SEL 0x8 + int board_eth_init(bd_t *bis) { #ifdef CONFIG_FMAN_ENET @@ -143,6 +148,10 @@ int board_eth_init(bd_t *bis) struct tgec_mdio_info tgec_mdio_info; unsigned int i, slot; int lane; + ccsr_gur_t *gur = (void *)CONFIG_SYS_MPC85xx_GUTS_ADDR; + int srds_prtcl = (in_be32(&gur->rcwsr[4]) & + FSL_CORENET_RCWSR4_SRDS_PRTCL) >> 26; + u8 mux = CPLD_READ(serdes_mux); printf("Initializing Fman\n"); @@ -172,6 +181,36 @@ int board_eth_init(bd_t *bis) fm_info_set_phy_address(FM1_DTSEC2, CONFIG_SYS_FM1_DTSEC2_PHY_ADDR); fm_info_set_phy_address(FM1_DTSEC3, CONFIG_SYS_FM1_DTSEC3_PHY_ADDR); + mux &= ~(CPLD_LANE_A_SEL | CPLD_LANE_C_SEL | CPLD_LANE_D_SEL); + switch (srds_prtcl) { + case 0x2: + case 0xf: + mux &= ~CPLD_LANE_G_SEL; + break; + case 0x5: + case 0x9: + case 0xa: + case 0x17: + mux |= CPLD_LANE_G_SEL; + break; + case 0x14: + mux = (mux & (~CPLD_LANE_G_SEL)) | CPLD_LANE_A_SEL; + break; + case 0x8: + case 0x16: + case 0x19: + case 0x1a: + mux |= CPLD_LANE_G_SEL | CPLD_LANE_C_SEL | CPLD_LANE_D_SEL; + break; + case 0x1c: + mux |= CPLD_LANE_G_SEL | CPLD_LANE_A_SEL; + break; + default: + printf("Fman:Unsupported SerDes Protocol 0x%02x\n", srds_prtcl); + break; + } + CPLD_WRITE(serdes_mux, mux); + for (i = FM1_DTSEC1; i < FM1_DTSEC1 + CONFIG_SYS_NUM_FM1_DTSEC; i++) { int idx = i - FM1_DTSEC1; -- 2.39.5