From f8bbb4dad0e9d91b7a51d6cc54dcf66d142f50fe Mon Sep 17 00:00:00 2001 From: Kyle Moffett Date: Wed, 7 Dec 2011 16:39:16 -0500 Subject: [PATCH] mpc85xx: Add board support for the eXMeritus HWW-1U-1A devices The eXMeritus HWW-1U-1A unit is a DO-160-certified 13lb 1U chassis with 3 independent TEMPEST zones. Two independent P2020 computers may be found inside each zone. Complete hardware support is included. High-level hardware overview: * DO-160 certified for passenger aircraft (noncritical) * TEMPEST ceritified for RED/BLACK separation * 3 zones per chassis, 2 computers per zone (total of 6) * Dual-core 1.066GHz P2020 per computer * One 2GB DDR2 SO-RDIMM module per computer (upgradable to 4GB) * Removable 80GB or 160GB Intel X18-M SSD per computer * Front-accessible dual-port E1000E per computer * Front-accessible serial console per computer * Front-accessible USB port per computer * Internal Gigabit crossover within each TEMPEST zone * Internal unidirectional fiber links across TEMPEST zones * Battery-backed DS1339 I2C RTC on each CPU. Combined, each 13lb 1U chassis contains 12GB RAM, 12 cores @ 1.066GHz, 12 front-accessible Gigabit Ethernet ports and 960GB of solid-state storage with a total power consumption of ~200W. Additional notes: * SPD detection is only known to work with the DO-160-certified DIMMs * CPU reset is a little quirky due to hardware misfeature. Proper support for the hardware reset mechanism has been left for a later patch series to address. Signed-off-by: Kyle Moffett Cc: Andy Fleming Signed-off-by: Kumar Gala --- MAINTAINERS | 4 + board/exmeritus/hww1u1a/Makefile | 48 ++++ board/exmeritus/hww1u1a/ddr.c | 34 +++ board/exmeritus/hww1u1a/gpios.h | 69 +++++ board/exmeritus/hww1u1a/hww1u1a.c | 277 ++++++++++++++++++ board/exmeritus/hww1u1a/law.c | 34 +++ board/exmeritus/hww1u1a/tlb.c | 106 +++++++ boards.cfg | 1 + include/configs/HWW1U1A.h | 451 ++++++++++++++++++++++++++++++ 9 files changed, 1024 insertions(+) create mode 100644 board/exmeritus/hww1u1a/Makefile create mode 100644 board/exmeritus/hww1u1a/ddr.c create mode 100644 board/exmeritus/hww1u1a/gpios.h create mode 100644 board/exmeritus/hww1u1a/hww1u1a.c create mode 100644 board/exmeritus/hww1u1a/law.c create mode 100644 board/exmeritus/hww1u1a/tlb.c create mode 100644 include/configs/HWW1U1A.h diff --git a/MAINTAINERS b/MAINTAINERS index 8bb757211c..0969a1b9ee 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -321,6 +321,10 @@ Reinhard Meyer TOP5200 MPC5200 TOP9000 ARM926EJS (AT91SAM9xxx SoC) +Kyle Moffett + + HWW1U1A P2020 + Tolunay Orkun csb272 PPC405GP diff --git a/board/exmeritus/hww1u1a/Makefile b/board/exmeritus/hww1u1a/Makefile new file mode 100644 index 0000000000..808d047fa0 --- /dev/null +++ b/board/exmeritus/hww1u1a/Makefile @@ -0,0 +1,48 @@ +# +# Copyright 2007-2009 Freescale Semiconductor, Inc. +# (C) Copyright 2001-2006 +# Wolfgang Denk, DENX Software Engineering, wd@denx.de. +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +include $(TOPDIR)/config.mk + +LIB = $(obj)lib$(BOARD).o + +COBJS-y += $(BOARD).o +COBJS-y += law.o +COBJS-y += tlb.o +COBJS-$(CONFIG_DDR_SPD) += ddr.o + +SRCS := $(SOBJS:.o=.S) $(COBJS-y:.o=.c) +OBJS := $(addprefix $(obj),$(COBJS-y)) +SOBJS := $(addprefix $(obj),$(SOBJS)) + +$(LIB): $(obj).depend $(OBJS) $(SOBJS) + $(call cmd_link_o_target, $(OBJS)) + +######################################################################### + +# defines $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +######################################################################### diff --git a/board/exmeritus/hww1u1a/ddr.c b/board/exmeritus/hww1u1a/ddr.c new file mode 100644 index 0000000000..36d02ad5d8 --- /dev/null +++ b/board/exmeritus/hww1u1a/ddr.c @@ -0,0 +1,34 @@ +/* + * Copyright 2009-2010 eXMeritus, A Boeing Company + * Copyright 2008-2009 Freescale Semiconductor, Inc. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * Version 2 as published by the Free Software Foundation. + */ + +#include + +#include +#include + +void fsl_ddr_board_options(memctl_options_t *popts, + dimm_params_t *pdimm, + unsigned int ctrl_num) +{ + /* + * We only support one DIMM, so according to the P2020 docs we should + * set the options as follows: + */ + popts->cs_local_opts[0].odt_rd_cfg = 0; + popts->cs_local_opts[0].odt_wr_cfg = 4; + popts->cs_local_opts[1].odt_rd_cfg = 0; + popts->cs_local_opts[1].odt_wr_cfg = 0; + popts->half_strength_driver_enable = 0; + + /* Manually configured for our static clock rate */ + popts->clk_adjust = 4; + popts->cpo_override = 4; + popts->write_data_delay = 2; + popts->twoT_en = 0; +} diff --git a/board/exmeritus/hww1u1a/gpios.h b/board/exmeritus/hww1u1a/gpios.h new file mode 100644 index 0000000000..ac56d42c61 --- /dev/null +++ b/board/exmeritus/hww1u1a/gpios.h @@ -0,0 +1,69 @@ +/* + * Copyright 2010 eXMeritus, A Boeing Company + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include + +/* Common CPU A/B GPIOs (GPIO8-GPIO15 and IRQ4-IRQ6) */ +#define GPIO_CPU_ID (1UL << (31 - 8)) +#define GPIO_BLUE_LED (1UL << (31 - 9)) +#define GPIO_DIMM_RESET (1UL << (31 - 10)) +#define GPIO_USB_RESET (1UL << (31 - 11)) +#define GPIO_UNUSED_12 (1UL << (31 - 12)) +#define GPIO_GETH0_RESET (1UL << (31 - 13)) +#define GPIO_RS422_RE (1UL << (31 - 14)) +#define GPIO_RS422_DE (1UL << (31 - 15)) +#define IRQ_I2CINT (1UL << (31 - 20)) +#define IRQ_FANINT (1UL << (31 - 21)) +#define IRQ_DIMM_EVENT (1UL << (31 - 22)) + +#define GPIO_RESETS (GPIO_DIMM_RESET|GPIO_USB_RESET|GPIO_GETH0_RESET) + +/* CPU A GPIOS (GPIO0-GPIO7 and IRQ0-IRQ3) */ +#define GPIO_CPUA_UNUSED_0 (1UL << (31 - 0)) +#define GPIO_CPUA_CPU_READY (1UL << (31 - 1)) +#define GPIO_CPUA_DEBUG_LED2 (1UL << (31 - 2)) +#define GPIO_CPUA_DEBUG_LED1 (1UL << (31 - 3)) +#define GPIO_CPUA_TDIS2B (1UL << (31 - 4)) /* MAC 2 TX B */ +#define GPIO_CPUA_TDIS2A (1UL << (31 - 5)) /* MAC 2 TX A */ +#define GPIO_CPUA_TDIS1B (1UL << (31 - 6)) /* MAC 1 TX B */ +#define GPIO_CPUA_TDIS1A (1UL << (31 - 7)) /* MAC 1 TX A */ +#define IRQ_CPUA_UNUSED_0 (1UL << (31 - 16)) +#define IRQ_CPUA_UNUSED_1 (1UL << (31 - 17)) +#define IRQ_CPUA_UNUSED_2 (1UL << (31 - 18)) +#define IRQ_CPUA_UNUSED_3 (1UL << (31 - 19)) + +/* CPU B GPIOS (GPIO0-GPIO7 and IRQ0-IRQ3) */ +#define GPIO_CPUB_RMUX_SEL1B (1UL << (31 - 0)) +#define GPIO_CPUB_RMUX_SEL0B (1UL << (31 - 1)) +#define GPIO_CPUB_RMUX_SEL1A (1UL << (31 - 2)) +#define GPIO_CPUB_RMUX_SEL0A (1UL << (31 - 3)) +#define GPIO_CPUB_UNUSED_4 (1UL << (31 - 4)) +#define GPIO_CPUB_CPU_READY (1UL << (31 - 5)) +#define GPIO_CPUB_DEBUG_LED2 (1UL << (31 - 6)) +#define GPIO_CPUB_DEBUG_LED1 (1UL << (31 - 7)) +#define IRQ_CPUB_SD_1A (1UL << (31 - 16)) +#define IRQ_CPUB_SD_2B (1UL << (31 - 17)) +#define IRQ_CPUB_SD_2A (1UL << (31 - 18)) +#define IRQ_CPUB_SD_1B (1UL << (31 - 19)) + +/* If it isn't CPU A then it's CPU B */ +static inline unsigned int hww1u1a_is_cpu_a(void) +{ + return !mpc85xx_gpio_get(GPIO_CPU_ID); +} diff --git a/board/exmeritus/hww1u1a/hww1u1a.c b/board/exmeritus/hww1u1a/hww1u1a.c new file mode 100644 index 0000000000..52c22faaa0 --- /dev/null +++ b/board/exmeritus/hww1u1a/hww1u1a.c @@ -0,0 +1,277 @@ +/* + * Copyright 2009-2011 eXMeritus, A Boeing Company + * Copyright 2007-2009 Freescale Semiconductor, Inc. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#include "gpios.h" + +DECLARE_GLOBAL_DATA_PTR; + +int checkboard(void) +{ + unsigned int gpio_high = 0; + unsigned int gpio_low = 0; + unsigned int gpio_in = 0; + unsigned int i; + + puts("Board: HWW-1U-1A "); + + /* + * First just figure out which CPU we're on, then use that to + * configure the lists of other GPIOs to be programmed. + */ + mpc85xx_gpio_set_in(GPIO_CPU_ID); + if (hww1u1a_is_cpu_a()) { + puts("CPU A\n"); + + /* We want to turn on some LEDs */ + gpio_high |= GPIO_CPUA_CPU_READY; + gpio_low |= GPIO_CPUA_DEBUG_LED1; + gpio_low |= GPIO_CPUA_DEBUG_LED2; + + /* Disable the unused transmitters */ + gpio_low |= GPIO_CPUA_TDIS1A; + gpio_high |= GPIO_CPUA_TDIS1B; + gpio_low |= GPIO_CPUA_TDIS2A; + gpio_high |= GPIO_CPUA_TDIS2B; + } else { + puts("CPU B\n"); + + /* We want to turn on some LEDs */ + gpio_high |= GPIO_CPUB_CPU_READY; + gpio_low |= GPIO_CPUB_DEBUG_LED1; + gpio_low |= GPIO_CPUB_DEBUG_LED2; + + /* Enable the appropriate receivers */ + gpio_high |= GPIO_CPUB_RMUX_SEL0A; + gpio_high |= GPIO_CPUB_RMUX_SEL0B; + gpio_low |= GPIO_CPUB_RMUX_SEL1A; + gpio_low |= GPIO_CPUB_RMUX_SEL1B; + } + + /* These GPIOs are common */ + gpio_in |= IRQ_I2CINT | IRQ_FANINT | IRQ_DIMM_EVENT; + gpio_low |= GPIO_RS422_RE; + gpio_high |= GPIO_RS422_DE; + + /* Ok, now go ahead and program all of those in one go */ + mpc85xx_gpio_set(gpio_high|gpio_low|gpio_in, + gpio_high|gpio_low, + gpio_high); + + /* + * If things have been taken out of reset early (for example, by one + * of the BDI3000 debuggers), then we need to put them back in reset + * and delay a while before we continue. + */ + if (mpc85xx_gpio_get(GPIO_RESETS)) { + ccsr_ddr_t *ddr = (ccsr_ddr_t *)CONFIG_SYS_MPC85xx_DDR_ADDR; + + puts("Debugger detected... extra device reset enabled!\n"); + + /* Put stuff into reset and disable the DDR controller */ + mpc85xx_gpio_set_low(GPIO_RESETS); + out_be32(&ddr->sdram_cfg, 0x00000000); + + puts(" Waiting 1 sec for reset..."); + for (i = 0; i < 10; i++) { + udelay(100000); + puts("."); + } + puts("\n"); + } + + /* Now bring everything back out of reset again */ + mpc85xx_gpio_set_high(GPIO_RESETS); + return 0; +} + +/* + * This little shell function just returns whether or not it's CPU A. + * It can be used to select the right device-tree when booting, etc. + */ +int do_hww1u1a_test_cpu_a(cmd_tbl_t *cmdtp, int flag, + int argc, char * const argv[]) +{ + if (argc > 1) + cmd_usage(cmdtp); + + if (hww1u1a_is_cpu_a()) + return 0; + else + return 1; +} +U_BOOT_CMD( + test_cpu_a, 1, 0, do_hww1u1a_test_cpu_a, + "Test if this is CPU A (versus B) on the eXMeritus HWW-1U-1A board", + "" +); + +/* Create a prompt-like string: "uboot@HOSTNAME% " */ +#define PROMPT_PREFIX "uboot@exm" +#define PROMPT_SUFFIX "% " + +/* This function returns a PS1 prompt based on the serial number */ +static char *hww1u1a_prompt; +const char *hww1u1a_get_ps1(void) +{ + unsigned long len, i, j; + const char *serialnr; + + /* If our prompt was already set, just use that */ + if (hww1u1a_prompt) + return hww1u1a_prompt; + + /* Use our serial number if present, otherwise a default */ + serialnr = getenv("serial#"); + if (!serialnr || !serialnr[0]) + serialnr = "999999-X"; + + /* + * We will turn the serial number into a hostname by: + * (A) Delete all non-alphanumerics. + * (B) Lowercase all letters. + * (C) Prefix "exm". + * (D) Suffix "a" for CPU A and "b" for CPU B. + */ + for (i = 0, len = 0; serialnr[i]; i++) { + if (isalnum(serialnr[i])) + len++; + } + + len += sizeof(PROMPT_PREFIX PROMPT_SUFFIX) + 1; /* Includes NUL */ + hww1u1a_prompt = malloc(len); + if (!hww1u1a_prompt) + return PROMPT_PREFIX "UNKNOWN(ENOMEM)" PROMPT_SUFFIX; + + /* Now actually fill it in */ + i = 0; + + /* Handle the prefix */ + for (j = 0; j < sizeof(PROMPT_PREFIX) - 1; j++) + hww1u1a_prompt[i++] = PROMPT_PREFIX[j]; + + /* Now the serial# part of the hostname */ + for (j = 0; serialnr[j]; j++) + if (isalnum(serialnr[j])) + hww1u1a_prompt[i++] = tolower(serialnr[j]); + + /* Now the CPU id ("a" or "b") */ + hww1u1a_prompt[i++] = hww1u1a_is_cpu_a() ? 'a' : 'b'; + + /* Finally the suffix */ + for (j = 0; j < sizeof(PROMPT_SUFFIX); j++) + hww1u1a_prompt[i++] = PROMPT_SUFFIX[j]; + + /* This should all have added up, but just in case */ + hww1u1a_prompt[len - 1] = '\0'; + + /* Now we're done */ + return hww1u1a_prompt; +} + +void pci_init_board(void) +{ + fsl_pcie_init_board(0); +} + +int board_early_init_r(void) +{ + const unsigned int flashbase = CONFIG_SYS_FLASH_BASE; + const u8 flash_esel = find_tlb_idx((void *)flashbase, 1); + + /* + * Remap bootflash region to caching-inhibited + * so that flash can be erased properly. + */ + + /* Flush d-cache and invalidate i-cache of any FLASH data */ + flush_dcache(); + invalidate_icache(); + + /* invalidate existing TLB entry for FLASH */ + disable_tlb(flash_esel); + + set_tlb(1, flashbase, CONFIG_SYS_FLASH_BASE_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, flash_esel, BOOKE_PAGESZ_256M, 1); + + return 0; +} + +int board_eth_init(bd_t *bis) +{ + struct tsec_info_struct tsec_info[4]; + struct fsl_pq_mdio_info mdio_info; + + SET_STD_TSEC_INFO(tsec_info[0], 1); + SET_STD_TSEC_INFO(tsec_info[1], 2); + SET_STD_TSEC_INFO(tsec_info[2], 3); + + if (hww1u1a_is_cpu_a()) + tsec_info[2].phyaddr = TSEC3_PHY_ADDR_CPUA; + else + tsec_info[2].phyaddr = TSEC3_PHY_ADDR_CPUB; + + mdio_info.regs = (struct tsec_mii_mng *)CONFIG_SYS_MDIO_BASE_ADDR; + mdio_info.name = DEFAULT_MII_NAME; + fsl_pq_mdio_init(bis, &mdio_info); + + tsec_eth_init(bis, tsec_info, 3); + return pci_eth_init(bis); +} + +void ft_board_setup(void *blob, bd_t *bd) +{ + phys_addr_t base; + phys_size_t size; + + ft_cpu_setup(blob, bd); + + base = getenv_bootm_low(); + size = getenv_bootm_size(); + + fdt_fixup_memory(blob, (u64)base, (u64)size); + + FT_FSL_PCI_SETUP; +} diff --git a/board/exmeritus/hww1u1a/law.c b/board/exmeritus/hww1u1a/law.c new file mode 100644 index 0000000000..1281c56f98 --- /dev/null +++ b/board/exmeritus/hww1u1a/law.c @@ -0,0 +1,34 @@ +/* + * Copyright 2008-2009 Freescale Semiconductor, Inc. + * + * (C) Copyright 2000 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include +#include +#include + +struct law_entry law_table[] = { + SET_LAW(CONFIG_SYS_FLASH_BASE_PHYS, LAW_SIZE_256M, LAW_TRGT_IF_LBC), +}; + +int num_law_entries = ARRAY_SIZE(law_table); diff --git a/board/exmeritus/hww1u1a/tlb.c b/board/exmeritus/hww1u1a/tlb.c new file mode 100644 index 0000000000..6c65206d3e --- /dev/null +++ b/board/exmeritus/hww1u1a/tlb.c @@ -0,0 +1,106 @@ +/* + * Copyright 2009-2010 eXMeritus, A Boeing Company + * Copyright 2008-2009 Freescale Semiconductor, Inc. + * + * (C) Copyright 2000 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include +#include + +struct fsl_e_tlb_entry tlb_table[] = { + /* TLB 0 - for temp stack in cache */ + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 0 * 1024, + CONFIG_SYS_INIT_RAM_ADDR_PHYS + 0 * 1024, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024, + CONFIG_SYS_INIT_RAM_ADDR_PHYS + 4 * 1024, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024, + CONFIG_SYS_INIT_RAM_ADDR_PHYS + 8 * 1024, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024, + CONFIG_SYS_INIT_RAM_ADDR_PHYS + 12 * 1024, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + + /* TLB 1 */ + /* *I*** - Boot page */ + SET_TLB_ENTRY(1, CONFIG_BPTR_VIRT_ADDR, + CONFIG_BPTR_VIRT_ADDR, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 0, BOOKE_PAGESZ_4K, 1), + + /* *I*G* - CCSRBAR */ + SET_TLB_ENTRY(1, CONFIG_SYS_CCSRBAR, + CONFIG_SYS_CCSRBAR_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 1, BOOKE_PAGESZ_1M, 1), + + /* + * W**G* - FLASH (Will be *I*G* after relocation to RAM) + * + * This maps both SPI FLASH chips (128MByte per chip) + */ + SET_TLB_ENTRY(1, CONFIG_SYS_FLASH_BASE, + CONFIG_SYS_FLASH_BASE_PHYS, + MAS3_SX|MAS3_SR, MAS2_W|MAS2_G, + 0, 2, BOOKE_PAGESZ_256M, 1), + + /* + * *I*G* - PCI memory + * + * We have 1.5GB total PCI-E memory space to map and we want to use + * the minimum possible number of TLB entries. Since Book-E TLB + * entries are sized in powers of 4, we use 1GB + 256MB + 256MB. + */ + SET_TLB_ENTRY(1, CONFIG_SYS_PCIE3_MEM_VIRT, + CONFIG_SYS_PCIE3_MEM_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 3, BOOKE_PAGESZ_1G, 1), + SET_TLB_ENTRY(1, CONFIG_SYS_PCIE3_MEM_VIRT + 0x40000000, + CONFIG_SYS_PCIE3_MEM_PHYS + 0x40000000, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 4, BOOKE_PAGESZ_256M, 1), + SET_TLB_ENTRY(1, CONFIG_SYS_PCIE3_MEM_VIRT + 0x50000000, + CONFIG_SYS_PCIE3_MEM_PHYS + 0x50000000, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 5, BOOKE_PAGESZ_256M, 1), + + /* + * *I*G* - PCI I/O + * + * This one entry covers all 3 64k PCI-E I/O windows + */ + SET_TLB_ENTRY(1, CONFIG_SYS_PCIE3_IO_VIRT, + CONFIG_SYS_PCIE3_IO_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 6, BOOKE_PAGESZ_256K, 1), +}; + +int num_tlb_entries = ARRAY_SIZE(tlb_table); diff --git a/boards.cfg b/boards.cfg index 12f5f6f16e..d847850068 100644 --- a/boards.cfg +++ b/boards.cfg @@ -599,6 +599,7 @@ sbc8560 powerpc mpc85xx sbc8560 - sbc8560_33 powerpc mpc85xx sbc8560 - - sbc8560 sbc8560_66 powerpc mpc85xx sbc8560 - - sbc8560 socrates powerpc mpc85xx socrates +HWW1U1A powerpc mpc85xx hww1u1a exmeritus MPC8536DS powerpc mpc85xx mpc8536ds freescale - MPC8536DS MPC8536DS_36BIT powerpc mpc85xx mpc8536ds freescale - MPC8536DS:36BIT MPC8536DS_NAND powerpc mpc85xx mpc8536ds freescale - MPC8536DS:NAND diff --git a/include/configs/HWW1U1A.h b/include/configs/HWW1U1A.h new file mode 100644 index 0000000000..c7a835bbda --- /dev/null +++ b/include/configs/HWW1U1A.h @@ -0,0 +1,451 @@ +/* + * Copyright 2009-2010 eXMeritus, A Boeing Company + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/* + * HardwareWall HWW-1U-1A airborne unit configuration file + */ +#ifndef __CONFIG_H +#define __CONFIG_H + +/* High-level system configuration options */ +#define CONFIG_BOOKE /* Power/PowerPC Book-E */ +#define CONFIG_E500 /* e500 (Power ISA v2.03 with SPE) */ +#define CONFIG_MPC85xx /* MPC8540/60/55/41/48 family */ +#define CONFIG_FSL_ELBC /* FreeScale Enhanced LocalBus Cntlr */ +#define CONFIG_FSL_LAW /* FreeScale Local Access Window */ +#define CONFIG_P2020 /* FreeScale P2020 */ +#define CONFIG_HWW1U1A /* eXMeritus HardwareWall HWW-1U-1A */ +#define CONFIG_MP /* Multiprocessing support */ +#define CONFIG_HWCONFIG /* Use hwconfig from environment */ + +#define CONFIG_L2_CACHE /* L2 cache enabled */ +#define CONFIG_BTB /* Branch predition enabled */ + +#define CONFIG_PANIC_HANG /* No board reset on panic */ +#define CONFIG_BOARD_EARLY_INIT_R /* Call board_early_init_r() */ +#define CONFIG_CMD_REGINFO /* Dump various CPU regs */ + +/* + * Allow the use of 36-bit physical addresses. Device-trees with 64-bit + * addresses have known compatibility issues with some existing kernels. + */ +#define CONFIG_ENABLE_36BIT_PHYS +#define CONFIG_PHYS_64BIT +#define CONFIG_ADDR_MAP +#define CONFIG_SYS_NUM_ADDR_MAP 16 /* Number of entries in TLB1 */ + +/* Reserve plenty of RAM for malloc (we have 2GB+) */ +#define CONFIG_SYS_MALLOC_LEN (1024 * 1024) + +/* How much L2 cache do we map so we can use it as RAM */ +#define CONFIG_SYS_INIT_RAM_LOCK +#define CONFIG_SYS_INIT_RAM_SIZE 0x00004000 + +/* This is our temporary global data area just above the stack */ +#define CONFIG_SYS_GBL_DATA_OFFSET \ + (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) + +/* The stack grows down from the global data area */ +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET + +/* Enable IRQs and watchdog with a 1000Hz system decrementer */ +#define CONFIG_CMD_IRQ +#define CONFIG_SYS_HZ 1000 + + +/* -------------------------------------------------------------------- */ + +/* + * Clock crystal configuration: + * (1) SYS: 66.666MHz +/- 50ppm (drives CPU/PCI/DDR) + * (2) CCB: Multiplier from SYS_CLK + * (3) RTC: 25.000MHz +/- 50ppm (sampled against CCB clock) + */ +#define CONFIG_SYS_CLK_FREQ 66666000/*Hz*/ +#define CONFIG_DDR_CLK_FREQ 66666000/*Hz*/ + + +/* -------------------------------------------------------------------- */ + +/* + * Memory map + * + * 0x0000_0000 0x7fff_ffff 2G DDR2 ECC SDRAM + * 0x8000_0000 0x9fff_ffff 512M PCI-E Bus 1 + * 0xa000_0000 0xbfff_ffff 512M PCI-E Bus 2 (unused) + * 0xc000_0000 0xdfff_ffff 512M PCI-E Bus 3 + * 0xe000_0000 0xe7ff_ffff 128M Spansion FLASH + * 0xe800_0000 0xefff_ffff 128M Spansion FLASH + * 0xffd0_0000 0xffd0_3fff 16K L1 boot stack (TLB0) + * 0xffe0_0000 0xffef_ffff 1M CCSR + * 0xffe0_5000 0xffe0_5fff 4K Enhanced LocalBus Controller + */ + +/* Virtual Memory Map */ +#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 +#define CONFIG_SYS_SDRAM_BASE 0x00000000 +#define CONFIG_SYS_PCIE3_MEM_VIRT 0x80000000 +#define CONFIG_SYS_PCIE2_MEM_VIRT 0xa0000000 +#define CONFIG_SYS_PCIE1_MEM_VIRT 0xc0000000 +#define CONFIG_SYS_FLASH_BASE 0xe0000000 +#define CONFIG_SYS_PCIE3_IO_VIRT 0xffc00000 +#define CONFIG_SYS_PCIE2_IO_VIRT 0xffc10000 +#define CONFIG_SYS_PCIE1_IO_VIRT 0xffc20000 +#define CONFIG_SYS_INIT_RAM_ADDR 0xffd00000 +#define CONFIG_SYS_CCSRBAR 0xffe00000 /* CCSRBAR @ runtime */ + +#define CONFIG_SYS_PCIE3_MEM_SIZE 0x20000000 /* 512M */ +#define CONFIG_SYS_PCIE2_MEM_SIZE 0x20000000 /* 512M */ +#define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */ +#define CONFIG_SYS_PCIE3_IO_SIZE 0x00010000 /* 64k */ +#define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */ +#define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */ + +/* Physical Memory Map */ +#define CONFIG_SYS_PCIE3_MEM_PHYS 0xc00000000ull +#define CONFIG_SYS_PCIE2_MEM_PHYS 0xc20000000ull +#define CONFIG_SYS_PCIE1_MEM_PHYS 0xc40000000ull +#define CONFIG_SYS_FLASH_BASE_PHYS 0xfe0000000ull +#define CONFIG_SYS_PCIE3_IO_PHYS 0xfffc00000ull +#define CONFIG_SYS_PCIE2_IO_PHYS 0xfffc10000ull +#define CONFIG_SYS_PCIE1_IO_PHYS 0xfffc20000ull +#define CONFIG_SYS_INIT_RAM_ADDR_PHYS 0xfffd00000ull +#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0xf /* for ASM code */ +#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW 0xffd00000 /* for ASM code */ +#define CONFIG_SYS_CCSRBAR_PHYS_HIGH 0xf /* for ASM code */ +#define CONFIG_SYS_CCSRBAR_PHYS_LOW 0xffe00000 /* for ASM code */ + + +/* -------------------------------------------------------------------- */ + +/* U-Boot image (MONITOR_BASE == TEXT_BASE) */ +#define CONFIG_RESET_VECTOR_ADDRESS 0xeffffffc /* Top address in flash */ +#define CONFIG_SYS_TEXT_BASE 0xeff80000 /* Start of U-Boot image */ +#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE +#define CONFIG_SYS_MONITOR_LEN 0x80000 /* 512kB (4 flash sectors) */ + +/* + * U-Boot Environment Image: The two sectors immediately below U-Boot + * form the U-Boot environment (regular and redundant). + */ +#define CONFIG_ENV_IS_IN_FLASH /* The environment image is stored in FLASH */ +#define CONFIG_ENV_OVERWRITE /* Allow "protected" variables to be erased */ +#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128kB (1 flash sector) */ +#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE) +#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR - CONFIG_ENV_SECT_SIZE) + +/* Only use 8kB of each environment sector for data */ +#define CONFIG_ENV_SIZE 0x2000 /* 8kB */ +#define CONFIG_ENV_SIZE_REDUND 0x2000 /* 8kB */ + + +/* -------------------------------------------------------------------- */ + +/* Serial Console Configuration */ +#define CONFIG_CONS_INDEX 1 +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 +#define CONFIG_SYS_NS16550_CLK get_bus_freq(0) + +#define CONFIG_BAUDRATE 115200 +#define CONFIG_SYS_BAUDRATE_TABLE \ + {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200} + +#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500) +#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600) + +/* Echo back characters received during a serial download */ +#define CONFIG_LOADS_ECHO + +/* Allow a serial-download to temporarily change baud */ +#define CONFIG_SYS_LOADS_BAUD_CHANGE + + +/* -------------------------------------------------------------------- */ + +/* PCI and PCI-Express Support */ +#define CONFIG_PCI /* Enable PCI/PCIE */ +#define CONFIG_PCI_PNP /* Scan PCI busses */ +#define CONFIG_CMD_PCI /* Enable the "pci" command */ +#define CONFIG_FSL_PCI_INIT /* Common FreeScale PCI initialization */ +#define CONFIG_FSL_PCIE_RESET /* We have PCI-E reset errata */ +#define CONFIG_SYS_PCI_64BIT /* PCI resources are 64-bit */ +#define CONFIG_PCI_SCAN_SHOW /* Display PCI scan during boot */ + +/* Enable 2 of the 3 PCI-E controllers */ +#define CONFIG_PCIE3 +#undef CONFIG_PCIE2 +#define CONFIG_PCIE1 + +/* Display human-readable names when initializing */ +#define CONFIG_SYS_PCIE3_NAME "Intel 82571EB" +#define CONFIG_SYS_PCIE2_NAME "Unused" +#define CONFIG_SYS_PCIE1_NAME "Silicon Image SIL3531" + +/* + * PCI bus addresses + * Memory space is mapped 1-1, but I/O space must start from 0. + */ +#define CONFIG_SYS_PCIE3_IO_BUS 0x00000000 +#define CONFIG_SYS_PCIE2_IO_BUS 0x00000000 +#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 +#define CONFIG_SYS_PCIE3_MEM_BUS 0xe0000000 +#define CONFIG_SYS_PCIE2_MEM_BUS 0xe0000000 +#define CONFIG_SYS_PCIE1_MEM_BUS 0xe0000000 + + +/* -------------------------------------------------------------------- */ + +/* Generic FreeScale hardware I2C support */ +#define CONFIG_HARD_I2C +#define CONFIG_FSL_I2C +#define CONFIG_CMD_I2C +#define CONFIG_I2C_MULTI_BUS +#define CONFIG_SYS_I2C_OFFSET 0x3000 +#define CONFIG_SYS_I2C2_OFFSET 0x3100 + +/* I2C bus configuration */ +#define CONFIG_SYS_I2C_SPEED 400000 +#define CONFIG_SYS_I2C_SLAVE 0x7F + +/* DDR2 SO-RDIMM SPD EEPROM is at I2C0-0x51 */ +#define CONFIG_SYS_SPD_BUS_NUM 0 +#define SPD_EEPROM_ADDRESS 0x51 + +/* DS1339 RTC is at I2C0-0x68 (I know it says "DS1337", it's a DS1339) */ +#define CONFIG_CMD_DATE +#define CONFIG_RTC_DS1337 +#define CONFIG_SYS_RTC_BUS_NUM 0 +#define CONFIG_SYS_I2C_RTC_ADDR 0x68 +/* Turn off RTC square-wave output to save battery */ +#define CONFIG_SYS_RTC_DS1337_NOOSC + +/* PCA9554 is at I2C1-0x3f (I know it says "PCA953X", it's a PCA9554) */ +#define CONFIG_PCA953X +#define CONFIG_CMD_PCA953X +#define CONFIG_CMD_PCA953X_INFO +#define CONFIG_SYS_I2C_PCA953X_ADDR 0x3f + + +/* -------------------------------------------------------------------- */ + +/* FreeScale DDR2/3 SDRAM Controller */ +#define CONFIG_FSL_DDR2 /* Our SDRAM slot is DDR2 */ +#define CONFIG_DDR_ECC /* Enable ECC by default */ +#define CONFIG_DDR_SPD /* Detect DDR config from SPD EEPROM */ +#define CONFIG_SPD_EEPROM /* ...why 2 config variables for this? */ +#define CONFIG_VERY_BIG_RAM /* Allow 2GB+ of RAM */ +#define CONFIG_CMD_SDRAM + +/* Standard P2020 DDR controller parameters */ +#define CONFIG_NUM_DDR_CONTROLLERS 1 +#define CONFIG_DIMM_SLOTS_PER_CTLR 1 +#define CONFIG_CHIP_SELECTS_PER_CTRL 2 + +/* Make sure to tell the DDR controller to preinitialze all of RAM */ +#define CONFIG_MEM_INIT_VALUE 0xDEADBEEF +#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER + + +/* -------------------------------------------------------------------- */ + +/* FLASH Memory Configuration (2x 128MB SPANSION FLASH) */ +#define CONFIG_FLASH_CFI_DRIVER +#define CONFIG_SYS_FLASH_CFI +#define CONFIG_SYS_FLASH_EMPTY_INFO +#define CONFIG_SYS_FLASH_AMD_CHECK_DQ7 + +/* Flash banks (2x 128MB) */ +#define FLASH0_PHYS (CONFIG_SYS_FLASH_BASE_PHYS + 0x8000000ull) +#define FLASH1_PHYS (CONFIG_SYS_FLASH_BASE_PHYS + 0x0000000ull) +#define CONFIG_SYS_MAX_FLASH_BANKS 2 +#define CONFIG_SYS_MAX_FLASH_SECT 1024 +#define CONFIG_SYS_FLASH_BANKS_LIST { FLASH0_PHYS, FLASH1_PHYS } + +/* + * Flash access modes and timings (values are the defaults after a RESET). + * + * NOTE: These could probably be optimized but are more than sufficient for + * this particular system for the moment. + */ +#define FLASH_BRx (BR_PS_16 | BR_MS_GPCM | BR_V) +#define FLASH_ORx (OR_GPCM_CSNT | OR_GPCM_ACS_DIV2 | OR_GPCM_XACS \ + | OR_GPCM_SCY_15 | OR_GPCM_TRLX | OR_GPCM_EHTR | OR_GPCM_EAD) + +/* Configure both flash banks */ +#define CONFIG_SYS_BR0_PRELIM (FLASH_BRx | BR_PHYS_ADDR(FLASH0_PHYS)) +#define CONFIG_SYS_BR1_PRELIM (FLASH_BRx | BR_PHYS_ADDR(FLASH1_PHYS)) +#define CONFIG_SYS_OR0_PRELIM (FLASH_ORx | OR_AM_128MB) +#define CONFIG_SYS_OR1_PRELIM (FLASH_ORx | OR_AM_128MB) + +/* Flash timeouts (in ms) */ +#define CONFIG_SYS_FLASH_ERASE_TOUT 60000UL /* Erase (60s) */ +#define CONFIG_SYS_FLASH_WRITE_TOUT 500UL /* Write (0.5s) */ + +/* Quiet flash testing */ +#define CONFIG_SYS_FLASH_QUIET_TEST + +/* Make program/erase count down from 45/5 (9....8....7....) */ +#define CONFIG_FLASH_SHOW_PROGRESS 45 + + +/* -------------------------------------------------------------------- */ + +/* Ethernet Device Support */ +#define CONFIG_MII /* Enable MII PHY code */ +#define CONFIG_MII_DEFAULT_TSEC /* ??? Copied from P2020DS */ +#define CONFIG_PHY_GIGE /* Support Gigabit PHYs */ +#define CONFIG_ETHPRIME "e1000#0" /* Default to external ports */ + +/* Turn on various helpful networking commands */ +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_MII +#define CONFIG_CMD_NET +#define CONFIG_CMD_PING + +/* On-chip FreeScale P2020 "tsec" Ethernet (oneway fibers and peer) */ +#define CONFIG_TSEC_ENET +#define CONFIG_TSEC1 +#define CONFIG_TSEC2 +#define CONFIG_TSEC3 +#define CONFIG_TSEC1_NAME "owt0" +#define CONFIG_TSEC2_NAME "owt1" +#define CONFIG_TSEC3_NAME "peer" +#define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) +#define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) +#define TSEC3_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) +#define TSEC1_PHYIDX 0 +#define TSEC2_PHYIDX 0 +#define TSEC3_PHYIDX 0 +#define TSEC1_PHY_ADDR 2 +#define TSEC2_PHY_ADDR 3 +#define TSEC3_PHY_ADDR 4 +#define TSEC3_PHY_ADDR_CPUA 4 +#define TSEC3_PHY_ADDR_CPUB 5 + +/* PCI-E dual-port E1000 (external ethernet ports) */ +#define CONFIG_E1000 +#define CONFIG_E1000_SPI +#define CONFIG_E1000_SPI_GENERIC +#define CONFIG_CMD_E1000 + +/* We need the SPI infrastructure to poke the E1000's EEPROM */ +#define CONFIG_SPI +#define CONFIG_SPI_X +#define CONFIG_CMD_SPI +#define MAX_SPI_BYTES 32 + + +/* -------------------------------------------------------------------- */ + +/* USB Thumbdrive Device Support */ +#define CONFIG_USB_EHCI +#define CONFIG_USB_EHCI_FSL +#define CONFIG_USB_STORAGE +#define CONFIG_EHCI_HCD_INIT_AFTER_RESET +#define CONFIG_CMD_USB + +/* Partition and Filesystem support */ +#define CONFIG_DOS_PARTITION +#define CONFIG_EFI_PARTITION +#define CONFIG_ISO_PARTITION +#define CONFIG_CMD_EXT2 +#define CONFIG_CMD_FAT + + +/* -------------------------------------------------------------------- */ + +/* Command line configuration. */ +#define CONFIG_CMDLINE_EDITING /* Enable command editing */ +#define CONFIG_COMMAND_HISTORY /* Enable command history */ +#define CONFIG_AUTO_COMPLETE /* Enable command completion */ +#define CONFIG_SYS_LONGHELP /* Enable detailed command help */ +#define CONFIG_SYS_MAXARGS 128 /* Up to 128 command-line args */ +#define CONFIG_SYS_PBSIZE 8192 /* Allow up to 8k printed lines */ +#define CONFIG_SYS_CBSIZE 4096 /* Allow up to 4k command lines */ +#define CONFIG_SYS_BARGSIZE 4096 /* Allow up to 4k boot args */ +#define CONFIG_SYS_HUSH_PARSER /* Enable a fancier shell */ +#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " /* Command-line continuation */ + +/* A little extra magic here for the prompt */ +#define CONFIG_SYS_PROMPT hww1u1a_get_ps1() +#ifndef __ASSEMBLY__ +const char *hww1u1a_get_ps1(void); +#endif + +/* Include a bunch of default commands we probably want */ +#include + +/* Other helpful shell-like commands */ +#define CONFIG_MD5 +#define CONFIG_SHA1 +#define CONFIG_CMD_MD5SUM +#define CONFIG_CMD_SHA1 +#define CONFIG_CMD_ASKENV +#define CONFIG_CMD_SETEXPR + + +/* -------------------------------------------------------------------- */ + +/* Image manipulation and booting */ + +/* We use the OpenFirmware-esque "Flattened Device Tree" */ +#define CONFIG_OF_LIBFDT +#define CONFIG_OF_BOARD_SETUP +#define CONFIG_OF_STDOUT_VIA_ALIAS + +/* + * For booting Linux, the board info and command line data + * have to be in the first 64 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CONFIG_CMD_ELF +#define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Maximum kernel memory map */ +#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Maximum kernel size of 64MB */ + +/* This is the default address for commands with an optional address arg */ +#define CONFIG_LOADADDR 100000 +#define CONFIG_SYS_LOAD_ADDR 0x100000 + +/* Test memory starting from the default load address to just below 2GB */ +#define CONFIG_SYS_MEMTEST_START CONFIG_SYS_LOAD_ADDR +#define CONFIG_SYS_MEMTEST_END 0x7f000000 + +#define CONFIG_BOOTDELAY 20 +#define CONFIG_BOOTCOMMAND "echo Not yet flashed" +#define CONFIG_BOOTARGS "" +#define CONFIG_BOOTARGS_DYNAMIC "console=ttyS0,${baudrate}n1" + +/* Extra environment parameters */ +#define CONFIG_EXTRA_ENV_SETTINGS \ + "preboot=setenv bootargs \"${bootargs} "CONFIG_BOOTARGS_DYNAMIC"\"\0" \ + "perf_mode=performance\0" \ + "hwconfig=" "fsl_ddr:ctlr_intlv=bank,bank_intlv=cs0_cs1;" \ + "usb1:dr_mode=host,phy_type=ulpi\0" \ + "flkernel=0xe8020000\0" \ + "flinitramfs=0xe8800000\0" \ + "fldevicetree=0xeff20000\0" \ + "flbootm=bootm ${flkernel} ${flinitramfs} ${fldevicetree}\0" \ + "flboot=run preboot; run flbootm\0" + +#endif /* __CONFIG_H */ -- 2.39.5