From 281e00a3be453a169d854f824a460359d10f92bb Mon Sep 17 00:00:00 2001 From: wdenk Date: Sun, 1 Aug 2004 22:48:16 +0000 Subject: [PATCH] * Code cleanup * Patch by Sascha Hauer, 28 Jun: - add generic support for Motorola i.MX architecture - add support for mx1ads, mx1fs2 and scb9328 boards * Patches by Marc Leeman, 23 Jul 2004: - Add define for the PCI/Memory Buffer Configuration Register - corrected comments in cpu/mpc824x/cpu_init.c * Add support for multiple serial interfaces (for example to allow modem dial-in / dial-out) --- CHANGELOG | 13 +- MAKEALL | 9 +- Makefile | 17 +- board/lwmon/lwmon.c | 8 + board/mx1ads/mx1ads.c | 44 +- board/mx1ads/syncflash.c | 42 +- board/mx1ads/u-boot.lds | 3 +- {cpu/mc9328 => board/mx1fs2}/Makefile | 24 +- board/mx1fs2/config.mk | 10 + board/mx1fs2/flash.c | 914 ++++++++++++++ board/mx1fs2/intel.h | 99 ++ board/mx1fs2/memsetup.S | 188 +++ board/mx1fs2/mx1fs2.c | 125 ++ board/mx1fs2/u-boot.lds | 56 + board/netphone/phone_console.c | 1 - board/sbc8560/sbc8560.c | 4 +- .../config.mk => board/scb9328/Makefile | 30 +- board/scb9328/config.mk | 10 + board/scb9328/flash.c | 321 +++++ board/scb9328/intel.h | 99 ++ board/scb9328/memsetup.S | 203 ++++ board/scb9328/scb9328.c | 73 ++ board/scb9328/u-boot.lds | 56 + board/total5200/total5200.c | 2 +- common/Makefile | 2 +- common/cmd_bmp.c | 9 +- common/cmd_nvedit.c | 6 + common/devices.c | 4 + common/serial.c | 196 +++ cpu/arm720t/cpu.c | 2 - cpu/arm920t/Makefile | 6 +- cpu/arm920t/imx_generic.c | 90 ++ cpu/arm920t/imx_interrupts.c | 117 ++ cpu/arm920t/imx_speed.c | 102 ++ cpu/arm920t/interrupts.c | 143 +-- cpu/arm920t/s3c24x0_interrupts.c | 180 +++ cpu/arm920t/{serial.c => s3c24x0_serial.c} | 34 +- cpu/arm920t/{speed.c => s3c24x0_speed.c} | 6 +- cpu/arm920t/start.S | 24 +- cpu/mc9328/cpu.c | 183 --- cpu/mc9328/interrupts.c | 249 ---- cpu/mc9328/serial.c | 133 --- cpu/mc9328/start.S | 388 ------ cpu/mpc824x/cpu_init.c | 6 +- cpu/mpc85xx/speed.c | 1 - cpu/mpc8xx/scc.c | 6 + cpu/mpc8xx/serial.c | 234 ++-- cpu/mpc8xx/spi.c | 10 +- doc/README.serial_multi | 37 + drivers/Makefile | 14 +- drivers/cfb_console.c | 1 - drivers/dm9000x.c | 590 +++++++++ drivers/dm9000x.h | 119 ++ drivers/serial_imx.c | 201 ++++ include/asm-arm/arch-arm920t/imx-regs.h | 571 +++++++++ include/common.h | 20 + include/commproc.h | 5 +- include/configs/PPChameleonEVB.h | 9 +- include/configs/Total5200.h | 1 + include/configs/lwmon.h | 18 +- include/configs/mx1ads.h | 89 +- include/configs/mx1fs2.h | 291 +++++ include/configs/scb9328.h | 357 ++++++ include/devices.h | 2 +- include/mc9328.h | 1051 ----------------- include/mpc824x.h | 1 + include/serial.h | 30 + lib_arm/board.c | 3 + lib_ppc/board.c | 6 +- post/ether.c | 27 +- post/uart.c | 53 +- 71 files changed, 5489 insertions(+), 2489 deletions(-) rename {cpu/mc9328 => board/mx1fs2}/Makefile (75%) create mode 100644 board/mx1fs2/config.mk create mode 100644 board/mx1fs2/flash.c create mode 100644 board/mx1fs2/intel.h create mode 100644 board/mx1fs2/memsetup.S create mode 100644 board/mx1fs2/mx1fs2.c create mode 100644 board/mx1fs2/u-boot.lds rename cpu/mc9328/config.mk => board/scb9328/Makefile (57%) create mode 100644 board/scb9328/config.mk create mode 100644 board/scb9328/flash.c create mode 100644 board/scb9328/intel.h create mode 100644 board/scb9328/memsetup.S create mode 100644 board/scb9328/scb9328.c create mode 100644 board/scb9328/u-boot.lds create mode 100644 common/serial.c create mode 100644 cpu/arm920t/imx_generic.c create mode 100644 cpu/arm920t/imx_interrupts.c create mode 100644 cpu/arm920t/imx_speed.c create mode 100644 cpu/arm920t/s3c24x0_interrupts.c rename cpu/arm920t/{serial.c => s3c24x0_serial.c} (78%) rename cpu/arm920t/{speed.c => s3c24x0_speed.c} (93%) delete mode 100644 cpu/mc9328/cpu.c delete mode 100644 cpu/mc9328/interrupts.c delete mode 100644 cpu/mc9328/serial.c delete mode 100644 cpu/mc9328/start.S create mode 100644 doc/README.serial_multi create mode 100644 drivers/dm9000x.c create mode 100644 drivers/dm9000x.h create mode 100644 drivers/serial_imx.c create mode 100644 include/asm-arm/arch-arm920t/imx-regs.h create mode 100644 include/configs/mx1fs2.h create mode 100644 include/configs/scb9328.h delete mode 100644 include/mc9328.h create mode 100644 include/serial.h diff --git a/CHANGELOG b/CHANGELOG index eb19c0e83c..e9a7998dc1 100644 --- a/CHANGELOG +++ b/CHANGELOG @@ -2,12 +2,23 @@ Changes since U-Boot 1.1.1: ====================================================================== +* Patch by Sascha Hauer, 28 Jun: + - add generic support for Motorola i.MX architecture + - add support for mx1ads, mx1fs2 and scb9328 boards + +* Patches by Marc Leeman, 23 Jul 2004: + - Add define for the PCI/Memory Buffer Configuration Register + - corrected comments in cpu/mpc824x/cpu_init.c + +* Add support for multiple serial interfaces + (for example to allow modem dial-in / dial-out) + * Patch by Stefan Roese, 15 Jul 2004: cpu/ppc4xx/sdram.c rewritten now using get_ram_size() * Fix NSCU config; add ethernet wakeup code. -* Add link for preloader for Motorola Coldfire to RAEDME.m68k +* Add link for preloader for Motorola Coldfire to README.m68k * Patch by Michael Bendzick, 12 Jul 2004: fix output formatting in drivers/cfi_flash.c diff --git a/MAKEALL b/MAKEALL index a4f2944021..131dc37ed0 100644 --- a/MAKEALL +++ b/MAKEALL @@ -139,11 +139,10 @@ LIST_ARM7="B2 ep7312 evb4510 impa7 modnet50" ######################################################################### LIST_ARM9=" \ - at91rm9200dk integratorcp integratorap \ - lpd7a400 mx1ads omap1510inn \ - omap1610h2 omap1610inn omap730p2 \ - smdk2400 smdk2410 trab \ - VCMA9 versatile \ + at91rm9200dk integratorcp integratorap lpd7a400 \ + mx1ads mx1fs2 omap1510inn omap1610h2 \ + omap1610inn omap730p2 scb9328 smdk2400 \ + smdk2410 trab VCMA9 versatile \ " ######################################################################### diff --git a/Makefile b/Makefile index 1601d7de80..5da162838d 100644 --- a/Makefile +++ b/Makefile @@ -757,6 +757,7 @@ PLU405_config: unconfig PMC405_config: unconfig @./mkconfig $(@:_config=) ppc ppc4xx pmc405 esd +PPChameleonEVB_config \ PPChameleonEVB_BA_25_config \ PPChameleonEVB_ME_25_config \ PPChameleonEVB_HI_25_config \ @@ -1154,6 +1155,12 @@ lpd7a400_config \ lpd7a404_config: unconfig @./mkconfig $(@:_config=) arm lh7a40x lpd7a40x +mx1ads_config : unconfig + @./mkconfig $(@:_config=) arm arm920t mx1ads + +mx1fs2_config : unconfig + @./mkconfig $(@:_config=) arm arm920t mx1fs2 + omap1510inn_config : unconfig @./mkconfig $(@:_config=) arm arm925t omap1510inn @@ -1192,6 +1199,9 @@ omap730p2_cs3boot_config : unconfig fi; @./mkconfig -a $(call xtract_omap730p2,$@) arm arm926ejs omap730p2 +scb9328_config : unconfig + @./mkconfig $(@:_config=) arm arm920t scb9328 + smdk2400_config : unconfig @./mkconfig $(@:_config=) arm arm920t smdk2400 @@ -1239,13 +1249,6 @@ versatile_config : unconfig B2_config : unconfig @./mkconfig $(@:_config=) arm s3c44b0 B2 dave -######################################################################### -## MC9328 (Dragonball) Systems -######################################################################### - -mx1ads_config : unconfig - @./mkconfig $(@:_config=) arm mc9328 mx1ads - ######################################################################### ## ARM720T Systems ######################################################################### diff --git a/board/lwmon/lwmon.c b/board/lwmon/lwmon.c index 6776dbf474..904e7ea98c 100644 --- a/board/lwmon/lwmon.c +++ b/board/lwmon/lwmon.c @@ -40,6 +40,7 @@ V* Verification: dzu@denx.de #include #include #include +#include #include #include /* for strdup */ @@ -468,6 +469,13 @@ int board_postclk_init (void) return (0); } +struct serial_device * default_serial_console (void) +{ + DECLARE_GLOBAL_DATA_PTR; + + return gd->do_mdm_init ? &serial_scc_device : &serial_smc_device; +} + static void kbd_init (void) { DECLARE_GLOBAL_DATA_PTR; diff --git a/board/mx1ads/mx1ads.c b/board/mx1ads/mx1ads.c index 453e4bb0a0..661fbab0ab 100644 --- a/board/mx1ads/mx1ads.c +++ b/board/mx1ads/mx1ads.c @@ -23,9 +23,9 @@ * MA 02111-1307 USA */ - #include -#include +/*#include */ +#include /* ------------------------------------------------------------------------- */ @@ -67,7 +67,6 @@ static inline void delay (unsigned long loops) { * Miscellaneous platform dependent initialisations */ - void SetAsynchMode(void) { __asm__ ( "mrc p15,0,r0,c1,c0,0 \n" @@ -85,42 +84,34 @@ int board_init (void) { volatile unsigned int tmp; - mc9328sid = MX1_SIDR; + mc9328sid = SIDR; - MX1_GPCR = 0x000003AB; /* I/O pad driving strength */ + GPCR = 0x000003AB; /* I/O pad driving strength */ /* MX1_CS1U = 0x00000A00; */ /* SRAM initialization */ /* MX1_CS1L = 0x11110601; */ - MX1_MPCTL0 = 0x04632410; /* setting for 150 MHz MCU PLL CLK */ - -/* MX1_MPCTL0 = 0x003f1437; */ /* setting for 192 MHz MCU PLL CLK */ + MPCTL0 = 0x04632410; /* setting for 150 MHz MCU PLL CLK */ /* set FCLK divider 1 (i.e. FCLK to MCU PLL CLK) and * BCLK divider to 2 (i.e. BCLK to 48 MHz) */ - MX1_CSCR = 0xAF000403; + CSCR = 0xAF000403; - MX1_CSCR |= 0x00200000; /* Trigger the restart bit(bit 21) */ - MX1_CSCR &= 0xFFFF7FFF; /* Program PRESC bit(bit 15) to 0 to divide-by-1 */ + CSCR |= 0x00200000; /* Trigger the restart bit(bit 21) */ + CSCR &= 0xFFFF7FFF; /* Program PRESC bit(bit 15) to 0 to divide-by-1 */ /* setup cs4 for cs8900 ethernet */ - MX1_CS4U = 0x00000F00; /* Initialize CS4 for CS8900 ethernet */ - MX1_CS4L = 0x00001501; + CS4U = 0x00000F00; /* Initialize CS4 for CS8900 ethernet */ + CS4L = 0x00001501; - MX1_GIUS_A &= 0xFF3FFFFF; - MX1_GPR_A &= 0xFF3FFFFF; + GIUS(0) &= 0xFF3FFFFF; + GPR(0) &= 0xFF3FFFFF; tmp = *(unsigned int *)(0x1500000C); tmp = *(unsigned int *)(0x1500000C); -/* setup timer 1 as system timer */ - - MX1_TPRER1 = 0x1f; /* divide by 32 */ - MX1_TCTL1 = 0x19; /* clock in from 32k Osc. */ - - SetAsynchMode(); gd->bd->bi_arch_number = 160; /* Arch number of MX1ADS Board */ @@ -131,19 +122,19 @@ int board_init (void) { dcache_enable(); /* set PERCLKs */ - MX1_PCDR = 0x00000055; /* set PERCLKS */ + PCDR = 0x00000055; /* set PERCLKS */ /* PERCLK3 is only used by SSI so the SSI driver can set it any value it likes * PERCLK1 and PERCLK2 are shared so DO NOT change it in any other place * all sources selected as normal interrupt */ - MX1_INTTYPEH = 0; - MX1_INTTYPEL = 0; +/* MX1_INTTYPEH = 0; + MX1_INTTYPEL = 0; +*/ return 0; } - int board_late_init(void) { setenv("stdout", "serial"); @@ -163,13 +154,10 @@ int board_late_init(void) { default : printf ("MX1ADS board with UNKNOWN MC9328 cpu, Silicon ID 0x%08x \n",mc9328sid); break; - } - return 0; } - int dram_init (void) { DECLARE_GLOBAL_DATA_PTR; diff --git a/board/mx1ads/syncflash.c b/board/mx1ads/syncflash.c index 09fc0f86e4..eb7fde5071 100644 --- a/board/mx1ads/syncflash.c +++ b/board/mx1ads/syncflash.c @@ -24,7 +24,8 @@ */ #include -#include +/*#include */ +#include typedef unsigned long * p_u32; @@ -33,27 +34,26 @@ typedef unsigned long * p_u32; flash_info_t flash_info[CFG_MAX_FLASH_BANKS]; /* info for FLASH chips */ /* Following Setting is for CSD1 */ -#define SFCTL 0x00221004 -#define reg_SFCTL __REG(SFCTL) +#define SFCTL 0x00221004 +#define reg_SFCTL __REG(SFCTL) -#define SYNCFLASH_A10 (0x00100000) +#define SYNCFLASH_A10 (0x00100000) -#define CMD_NORMAL (0x81020300) /* Normal Mode */ -#define CMD_PREC (CMD_NORMAL + 0x10000000) /* Precharge Command */ -#define CMD_AUTO (CMD_NORMAL + 0x20000000) /* Auto Refresh Command */ -#define CMD_LMR (CMD_NORMAL + 0x30000000) /* Load Mode Register Command */ -#define CMD_LCR (CMD_NORMAL + 0x60000000) /* LCR Command */ -#define CMD_PROGRAM (CMD_NORMAL + 0x70000000) +#define CMD_NORMAL (0x81020300) /* Normal Mode */ +#define CMD_PREC (CMD_NORMAL + 0x10000000) /* Precharge Command */ +#define CMD_AUTO (CMD_NORMAL + 0x20000000) /* Auto Refresh Command */ +#define CMD_LMR (CMD_NORMAL + 0x30000000) /* Load Mode Register Command */ +#define CMD_LCR (CMD_NORMAL + 0x60000000) /* LCR Command */ +#define CMD_PROGRAM (CMD_NORMAL + 0x70000000) -#define MODE_REG_VAL (CFG_FLASH_BASE+0x0008CC00) /* Cas Latency 3 */ +#define MODE_REG_VAL (CFG_FLASH_BASE+0x0008CC00) /* Cas Latency 3 */ /* LCR Command */ -#define LCR_READSTATUS (0x0001C000) /* 0x70 */ -#define LCR_ERASE_CONFIRM (0x00008000) /* 0x20 */ -#define LCR_ERASE_NVMODE (0x0000C000) /* 0x30 */ -#define LCR_PROG_NVMODE (0x00028000) /* 0xA0 */ -#define LCR_SR_CLEAR (0x00014000) /* 0x50 */ - +#define LCR_READSTATUS (0x0001C000) /* 0x70 */ +#define LCR_ERASE_CONFIRM (0x00008000) /* 0x20 */ +#define LCR_ERASE_NVMODE (0x0000C000) /* 0x30 */ +#define LCR_PROG_NVMODE (0x00028000) /* 0xA0 */ +#define LCR_SR_CLEAR (0x00014000) /* 0x50 */ /* Get Status register */ u32 SF_SR(void) { @@ -82,7 +82,6 @@ u8 SF_Ready(void) { if ((tmp & 0x00000080) && (tmp & 0x0000001C)) { printf ("SyncFlash Error code %08x\n",tmp); - }; if (tmp == 0x00800080) /* Test Bit 7 of SR */ @@ -98,7 +97,6 @@ void SF_PrechargeAll(void) { reg_SFCTL = CMD_PREC; /* Set Precharge Command */ tmp = __REG(CFG_FLASH_BASE + SYNCFLASH_A10); /* Issue Precharge All Command */ - } /* set SyncFlash to normal mode */ @@ -128,7 +126,6 @@ void SF_Erase(u32 RowAddress) { while(!SF_Ready()); } - void SF_NvmodeErase(void) { SF_PrechargeAll(); @@ -149,10 +146,8 @@ void SF_NvmodeWrite(void) { reg_SFCTL = CMD_NORMAL; /* Return to Normal mode */ __REG(CFG_FLASH_BASE+LCR_PROG_NVMODE) = 0xC0C0C0C0; /* Confirm not needed */ - } - /****************************************************************************************/ ulong flash_init(void) { @@ -195,7 +190,6 @@ ulong flash_init(void) { return FLASH_BANK_SIZE; } - void flash_print_info (flash_info_t *info) { int i; @@ -209,7 +203,6 @@ void flash_print_info (flash_info_t *info) { break; } - switch (info->flash_id & FLASH_TYPEMASK) { case (FLASH_MT28S4M16LC & FLASH_TYPEMASK): printf("2x FLASH_MT28S4M16LC (16MB Total)\n"); @@ -236,7 +229,6 @@ void flash_print_info (flash_info_t *info) { printf ("\n"); } - /*-----------------------------------------------------------------------*/ int flash_erase (flash_info_t *info, int s_first, int s_last) { diff --git a/board/mx1ads/u-boot.lds b/board/mx1ads/u-boot.lds index 53743cdb80..649216abda 100644 --- a/board/mx1ads/u-boot.lds +++ b/board/mx1ads/u-boot.lds @@ -23,7 +23,6 @@ * MA 02111-1307 USA */ - OUTPUT_FORMAT("elf32-littlearm", "elf32-littlearm", "elf32-littlearm") OUTPUT_ARCH(arm) ENTRY(_start) @@ -34,7 +33,7 @@ SECTIONS . = ALIGN(4); .text : { - cpu/mc9328/start.o (.text) + cpu/arm920t/start.o (.text) *(.text) } diff --git a/cpu/mc9328/Makefile b/board/mx1fs2/Makefile similarity index 75% rename from cpu/mc9328/Makefile rename to board/mx1fs2/Makefile index fccc6ab912..86aef5c3da 100644 --- a/cpu/mc9328/Makefile +++ b/board/mx1fs2/Makefile @@ -1,5 +1,5 @@ # -# (C) Copyright 2000, 2001, 2002 +# (C) Copyright 2000-2004 # Wolfgang Denk, DENX Software Engineering, wd@denx.de. # # See file CREDITS for list of people who contributed to this @@ -23,21 +23,25 @@ include $(TOPDIR)/config.mk -LIB = lib$(CPU).a +LIB = lib$(BOARD).a -START = start.o -OBJS = serial.o interrupts.o cpu.o +OBJS := mx1fs2.o flash.o +SOBJS := memsetup.o -all: .depend $(START) $(LIB) +$(LIB): $(OBJS) $(SOBJS) + $(AR) crv $@ $^ -$(LIB): $(OBJS) - $(AR) crv $@ $(OBJS) +clean: + rm -f $(SOBJS) $(OBJS) + +distclean: clean + rm -f $(LIB) core *.bak .depend ######################################################################### -.depend: Makefile $(START:.o=.S) $(OBJS:.o=.c) - $(CC) -M $(CFLAGS) $(START:.o=.S) $(OBJS:.o=.c) > $@ +.depend: Makefile $(SOBJS:.o=.S) $(OBJS:.o=.c) + $(CC) -M $(CPPFLAGS) $(SOBJS:.o=.S) $(OBJS:.o=.c) > $@ -sinclude .depend +-include .depend ######################################################################### diff --git a/board/mx1fs2/config.mk b/board/mx1fs2/config.mk new file mode 100644 index 0000000000..59ab542465 --- /dev/null +++ b/board/mx1fs2/config.mk @@ -0,0 +1,10 @@ +# +# This config file is used for compilation of IMX sources +# +# You might change location of U-Boot in memory by setting right TEXT_BASE. +# This allows for example having one copy located at the end of ram and stored +# in flash device and later on while developing use other location to test +# the code in RAM device only. +# + +TEXT_BASE = 0x08f00000 diff --git a/board/mx1fs2/flash.c b/board/mx1fs2/flash.c new file mode 100644 index 0000000000..3a79a9eb4b --- /dev/null +++ b/board/mx1fs2/flash.c @@ -0,0 +1,914 @@ +/* + * (C) 2000-2004 Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * (C) 2003 August Hoeraendl, Logotronic GmbH + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#undef CONFIG_FLASH_16BIT + +#include + +#if defined CFG_JFFS_CUSTOM_PART +#include +#endif + +#define FLASH_BANK_SIZE MX1FS2_FLASH_BANK_SIZE +#define MAIN_SECT_SIZE MX1FS2_FLASH_SECT_SIZE + +flash_info_t flash_info[CFG_MAX_FLASH_BANKS]; /* info for FLASH chips */ + +/* + * NOTE - CONFIG_FLASH_16BIT means the CPU interface is 16-bit, it + * has nothing to do with the flash chip being 8-bit or 16-bit. + */ +#ifdef CONFIG_FLASH_16BIT +typedef unsigned short FLASH_PORT_WIDTH; +typedef volatile unsigned short FLASH_PORT_WIDTHV; + +#define FLASH_ID_MASK 0xFFFF +#else +typedef unsigned long FLASH_PORT_WIDTH; +typedef volatile unsigned long FLASH_PORT_WIDTHV; + +#define FLASH_ID_MASK 0xFFFFFFFF +#endif + +#define FPW FLASH_PORT_WIDTH +#define FPWV FLASH_PORT_WIDTHV + +#define ORMASK(size) ((-size) & OR_AM_MSK) + +/*----------------------------------------------------------------------- + * Functions + */ +#if 0 +static ulong flash_get_size(FPWV * addr, flash_info_t * info); +static void flash_get_offsets(ulong base, flash_info_t * info); +#endif +static void flash_reset(flash_info_t * info); +static int write_word_intel(flash_info_t * info, FPWV * dest, FPW data); +static int write_word_amd(flash_info_t * info, FPWV * dest, FPW data); +#define write_word(in, de, da) write_word_amd(in, de, da) +#ifdef CFG_FLASH_PROTECTION +static void flash_sync_real_protect(flash_info_t * info); +#endif + +#if defined CFG_JFFS_CUSTOM_PART + +/** + * jffs2_part_info - get information about a JFFS2 partition + * + * @part_num: number of the partition you want to get info about + * @return: struct part_info* in case of success, 0 if failure + */ + +static struct part_info part; +static int current_part = -1; + +struct part_info * +jffs2_part_info(int part_num) +{ + void *jffs2_priv_saved = part.jffs2_priv; + + printf("jffs2_part_info: part_num=%i\n", part_num); + + if (current_part == part_num) + return ∂ + + /* rootfs */ + if (part_num == 0) { + memset(&part, 0, sizeof (part)); + + part.offset = (char *) MX1FS2_JFFS2_PART0_START; + part.size = MX1FS2_JFFS2_PART0_SIZE; + + /* Mark the struct as ready */ + current_part = part_num; + + printf("part.offset = 0x%08x\n", (unsigned int) part.offset); + printf("part.size = 0x%08x\n", (unsigned int) part.size); + } + + /* userfs */ + if (part_num == 1) { + memset(&part, 0, sizeof (part)); + + part.offset = (char *) MX1FS2_JFFS2_PART1_START; + part.size = MX1FS2_JFFS2_PART1_SIZE; + + /* Mark the struct as ready */ + current_part = part_num; + + printf("part.offset = 0x%08x\n", (unsigned int) part.offset); + printf("part.size = 0x%08x\n", (unsigned int) part.size); + } + + if (current_part == part_num) { + part.usr_priv = ¤t_part; + part.jffs2_priv = jffs2_priv_saved; + return ∂ + } + + printf("jffs2_part_info: end of partition table\n"); + return 0; +} +#endif /* CFG_JFFS_CUSTOM_PART */ + +/*----------------------------------------------------------------------- + * flash_init() + * + * sets up flash_info and returns size of FLASH (bytes) + */ +ulong +flash_init(void) +{ + int i, j; + ulong size = 0; + + for (i = 0; i < CFG_MAX_FLASH_BANKS; i++) { + ulong flashbase = 0; + flash_info[i].flash_id = + (FLASH_MAN_AMD & FLASH_VENDMASK) | + (FLASH_AM640U & FLASH_TYPEMASK); + flash_info[i].size = FLASH_BANK_SIZE; + flash_info[i].sector_count = CFG_MAX_FLASH_SECT; + memset(flash_info[i].protect, 0, CFG_MAX_FLASH_SECT); + switch (i) { + case 0: + flashbase = MX1FS2_FLASH_BASE; + break; + default: + panic("configured too many flash banks!\n"); + break; + } + for (j = 0; j < flash_info[i].sector_count; j++) { + flash_info[i].start[j] = flashbase + j * MAIN_SECT_SIZE; + } + size += flash_info[i].size; + } + + /* Protect monitor and environment sectors */ + flash_protect(FLAG_PROTECT_SET, + CFG_FLASH_BASE, + CFG_FLASH_BASE + _bss_start - _armboot_start, + &flash_info[0]); + + flash_protect(FLAG_PROTECT_SET, + CFG_ENV_ADDR, + CFG_ENV_ADDR + CFG_ENV_SIZE - 1, &flash_info[0]); + + return size; +} + +/*----------------------------------------------------------------------- + */ +static void +flash_reset(flash_info_t * info) +{ + FPWV *base = (FPWV *) (info->start[0]); + + /* Put FLASH back in read mode */ + if ((info->flash_id & FLASH_VENDMASK) == FLASH_MAN_INTEL) + *base = (FPW) 0x00FF00FF; /* Intel Read Mode */ + else if ((info->flash_id & FLASH_VENDMASK) == FLASH_MAN_AMD) + *base = (FPW) 0x00F000F0; /* AMD Read Mode */ +} + +/*----------------------------------------------------------------------- + */ +#if 0 +static void +flash_get_offsets(ulong base, flash_info_t * info) +{ + int i; + + /* set up sector start address table */ + if ((info->flash_id & FLASH_VENDMASK) == FLASH_MAN_INTEL + && (info->flash_id & FLASH_BTYPE)) { + int bootsect_size; /* number of bytes/boot sector */ + int sect_size; /* number of bytes/regular sector */ + + bootsect_size = 0x00002000 * (sizeof (FPW) / 2); + sect_size = 0x00010000 * (sizeof (FPW) / 2); + + /* set sector offsets for bottom boot block type */ + for (i = 0; i < 8; ++i) { + info->start[i] = base + (i * bootsect_size); + } + for (i = 8; i < info->sector_count; i++) { + info->start[i] = base + ((i - 7) * sect_size); + } + } else if ((info->flash_id & FLASH_VENDMASK) == FLASH_MAN_AMD + && (info->flash_id & FLASH_TYPEMASK) == FLASH_AM640U) { + + int sect_size; /* number of bytes/sector */ + + sect_size = 0x00010000 * (sizeof (FPW) / 2); + + /* set up sector start address table (uniform sector type) */ + for (i = 0; i < info->sector_count; i++) + info->start[i] = base + (i * sect_size); + } +} +#endif /* 0 */ + +/*----------------------------------------------------------------------- + */ + +void +flash_print_info(flash_info_t * info) +{ + int i; + uchar *boottype; + uchar *bootletter; + uchar *fmt; + uchar botbootletter[] = "B"; + uchar topbootletter[] = "T"; + uchar botboottype[] = "bottom boot sector"; + uchar topboottype[] = "top boot sector"; + + if (info->flash_id == FLASH_UNKNOWN) { + printf("missing or unknown FLASH type\n"); + return; + } + + switch (info->flash_id & FLASH_VENDMASK) { + case FLASH_MAN_AMD: + printf("AMD "); + break; + case FLASH_MAN_BM: + printf("BRIGHT MICRO "); + break; + case FLASH_MAN_FUJ: + printf("FUJITSU "); + break; + case FLASH_MAN_SST: + printf("SST "); + break; + case FLASH_MAN_STM: + printf("STM "); + break; + case FLASH_MAN_INTEL: + printf("INTEL "); + break; + default: + printf("Unknown Vendor "); + break; + } + + /* check for top or bottom boot, if it applies */ + if (info->flash_id & FLASH_BTYPE) { + boottype = botboottype; + bootletter = botbootletter; + } else { + boottype = topboottype; + bootletter = topbootletter; + } + + switch (info->flash_id & FLASH_TYPEMASK) { + case FLASH_AM640U: + fmt = "29LV641D (64 Mbit, uniform sectors)\n"; + break; + case FLASH_28F800C3B: + case FLASH_28F800C3T: + fmt = "28F800C3%s (8 Mbit, %s)\n"; + break; + case FLASH_INTEL800B: + case FLASH_INTEL800T: + fmt = "28F800B3%s (8 Mbit, %s)\n"; + break; + case FLASH_28F160C3B: + case FLASH_28F160C3T: + fmt = "28F160C3%s (16 Mbit, %s)\n"; + break; + case FLASH_INTEL160B: + case FLASH_INTEL160T: + fmt = "28F160B3%s (16 Mbit, %s)\n"; + break; + case FLASH_28F320C3B: + case FLASH_28F320C3T: + fmt = "28F320C3%s (32 Mbit, %s)\n"; + break; + case FLASH_INTEL320B: + case FLASH_INTEL320T: + fmt = "28F320B3%s (32 Mbit, %s)\n"; + break; + case FLASH_28F640C3B: + case FLASH_28F640C3T: + fmt = "28F640C3%s (64 Mbit, %s)\n"; + break; + case FLASH_INTEL640B: + case FLASH_INTEL640T: + fmt = "28F640B3%s (64 Mbit, %s)\n"; + break; + default: + fmt = "Unknown Chip Type\n"; + break; + } + + printf(fmt, bootletter, boottype); + + printf(" Size: %ld MB in %d Sectors\n", + info->size >> 20, info->sector_count); + + printf(" Sector Start Addresses:"); + + for (i = 0; i < info->sector_count; ++i) { + if ((i % 5) == 0) { + printf("\n "); + } + + printf(" %08lX%s", info->start[i], + info->protect[i] ? " (RO)" : " "); + } + + printf("\n"); +} + +/*----------------------------------------------------------------------- + */ + +/* + * The following code cannot be run from FLASH! + */ + +#if 0 +ulong +flash_get_size(FPWV * addr, flash_info_t * info) +{ + /* Write auto select command: read Manufacturer ID */ + + /* Write auto select command sequence and test FLASH answer */ + addr[0x0555] = (FPW) 0x00AA00AA; /* for AMD, Intel ignores this */ + addr[0x02AA] = (FPW) 0x00550055; /* for AMD, Intel ignores this */ + addr[0x0555] = (FPW) 0x00900090; /* selects Intel or AMD */ + + /* The manufacturer codes are only 1 byte, so just use 1 byte. + * This works for any bus width and any FLASH device width. + */ + switch (addr[0] & 0xff) { + + case (uchar) AMD_MANUFACT: + info->flash_id = FLASH_MAN_AMD; + break; + + case (uchar) INTEL_MANUFACT: + info->flash_id = FLASH_MAN_INTEL; + break; + + default: + info->flash_id = FLASH_UNKNOWN; + info->sector_count = 0; + info->size = 0; + break; + } + + /* Check 16 bits or 32 bits of ID so work on 32 or 16 bit bus. */ + if (info->flash_id != FLASH_UNKNOWN) + switch (addr[1]) { + + case (FPW) AMD_ID_LV640U: /* 29LV640 and 29LV641 have same ID */ + info->flash_id += FLASH_AM640U; + info->sector_count = 128; + info->size = 0x00800000 * (sizeof (FPW) / 2); + break; /* => 8 or 16 MB */ + + case (FPW) INTEL_ID_28F800C3B: + info->flash_id += FLASH_28F800C3B; + info->sector_count = 23; + info->size = 0x00100000 * (sizeof (FPW) / 2); + break; /* => 1 or 2 MB */ + + case (FPW) INTEL_ID_28F800B3B: + info->flash_id += FLASH_INTEL800B; + info->sector_count = 23; + info->size = 0x00100000 * (sizeof (FPW) / 2); + break; /* => 1 or 2 MB */ + + case (FPW) INTEL_ID_28F160C3B: + info->flash_id += FLASH_28F160C3B; + info->sector_count = 39; + info->size = 0x00200000 * (sizeof (FPW) / 2); + break; /* => 2 or 4 MB */ + + case (FPW) INTEL_ID_28F160B3B: + info->flash_id += FLASH_INTEL160B; + info->sector_count = 39; + info->size = 0x00200000 * (sizeof (FPW) / 2); + break; /* => 2 or 4 MB */ + + case (FPW) INTEL_ID_28F320C3B: + info->flash_id += FLASH_28F320C3B; + info->sector_count = 71; + info->size = 0x00400000 * (sizeof (FPW) / 2); + break; /* => 4 or 8 MB */ + + case (FPW) INTEL_ID_28F320B3B: + info->flash_id += FLASH_INTEL320B; + info->sector_count = 71; + info->size = 0x00400000 * (sizeof (FPW) / 2); + break; /* => 4 or 8 MB */ + + case (FPW) INTEL_ID_28F640C3B: + info->flash_id += FLASH_28F640C3B; + info->sector_count = 135; + info->size = 0x00800000 * (sizeof (FPW) / 2); + break; /* => 8 or 16 MB */ + + case (FPW) INTEL_ID_28F640B3B: + info->flash_id += FLASH_INTEL640B; + info->sector_count = 135; + info->size = 0x00800000 * (sizeof (FPW) / 2); + break; /* => 8 or 16 MB */ + + default: + info->flash_id = FLASH_UNKNOWN; + info->sector_count = 0; + info->size = 0; + return (0); /* => no or unknown flash */ + } + + flash_get_offsets((ulong) addr, info); + + /* Put FLASH back in read mode */ + flash_reset(info); + + return (info->size); +} +#endif /* 0 */ + +#ifdef CFG_FLASH_PROTECTION +/*----------------------------------------------------------------------- + */ + +static void +flash_sync_real_protect(flash_info_t * info) +{ + FPWV *addr = (FPWV *) (info->start[0]); + FPWV *sect; + int i; + + switch (info->flash_id & FLASH_TYPEMASK) { + case FLASH_28F800C3B: + case FLASH_28F800C3T: + case FLASH_28F160C3B: + case FLASH_28F160C3T: + case FLASH_28F320C3B: + case FLASH_28F320C3T: + case FLASH_28F640C3B: + case FLASH_28F640C3T: + /* check for protected sectors */ + *addr = (FPW) 0x00900090; + for (i = 0; i < info->sector_count; i++) { + /* read sector protection at sector address, (A7 .. A0) = 0x02. + * D0 = 1 for each device if protected. + * If at least one device is protected the sector is marked + * protected, but mixed protected and unprotected devices + * within a sector should never happen. + */ + sect = (FPWV *) (info->start[i]); + info->protect[i] = + (sect[2] & (FPW) (0x00010001)) ? 1 : 0; + } + + /* Put FLASH back in read mode */ + flash_reset(info); + break; + + case FLASH_AM640U: + default: + /* no hardware protect that we support */ + break; + } +} +#endif + +/*----------------------------------------------------------------------- + */ + +int +flash_erase(flash_info_t * info, int s_first, int s_last) +{ + FPWV *addr; + int flag, prot, sect; + int intel = (info->flash_id & FLASH_VENDMASK) == FLASH_MAN_INTEL; + ulong start, now, last; + int rcode = 0; + + if ((s_first < 0) || (s_first > s_last)) { + if (info->flash_id == FLASH_UNKNOWN) { + printf("- missing\n"); + } else { + printf("- no sectors to erase\n"); + } + return 1; + } + + switch (info->flash_id & FLASH_TYPEMASK) { + case FLASH_INTEL800B: + case FLASH_INTEL160B: + case FLASH_INTEL320B: + case FLASH_INTEL640B: + case FLASH_28F800C3B: + case FLASH_28F160C3B: + case FLASH_28F320C3B: + case FLASH_28F640C3B: + case FLASH_AM640U: + break; + case FLASH_UNKNOWN: + default: + printf("Can't erase unknown flash type %08lx - aborted\n", + info->flash_id); + return 1; + } + + prot = 0; + for (sect = s_first; sect <= s_last; ++sect) { + if (info->protect[sect]) { + prot++; + } + } + + if (prot) { + printf("- Warning: %d protected sectors will not be erased!\n", + prot); + } else { + printf("\n"); + } + + start = get_timer(0); + last = start; + + /* Start erase on unprotected sectors */ + for (sect = s_first; sect <= s_last && rcode == 0; sect++) { + + if (info->protect[sect] != 0) /* protected, skip it */ + continue; + + /* Disable interrupts which might cause a timeout here */ + flag = disable_interrupts(); + + addr = (FPWV *) (info->start[sect]); + if (intel) { + *addr = (FPW) 0x00500050; /* clear status register */ + *addr = (FPW) 0x00200020; /* erase setup */ + *addr = (FPW) 0x00D000D0; /* erase confirm */ + } else { + /* must be AMD style if not Intel */ + FPWV *base; /* first address in bank */ + + base = (FPWV *) (info->start[0]); + base[0x0555] = (FPW) 0x00AA00AA; /* unlock */ + base[0x02AA] = (FPW) 0x00550055; /* unlock */ + base[0x0555] = (FPW) 0x00800080; /* erase mode */ + base[0x0555] = (FPW) 0x00AA00AA; /* unlock */ + base[0x02AA] = (FPW) 0x00550055; /* unlock */ + *addr = (FPW) 0x00300030; /* erase sector */ + } + + /* re-enable interrupts if necessary */ + if (flag) + enable_interrupts(); + + /* wait at least 50us for AMD, 80us for Intel. + * Let's wait 1 ms. + */ + udelay(1000); + + while ((*addr & (FPW) 0x00800080) != (FPW) 0x00800080) { + if ((now = get_timer(0)) - start > CFG_FLASH_ERASE_TOUT) { + printf("Timeout\n"); + + if (intel) { + /* suspend erase */ + *addr = (FPW) 0x00B000B0; + } + + flash_reset(info); /* reset to read mode */ + rcode = 1; /* failed */ + break; + } + + /* show that we're waiting */ + if ((now - last) > 1000) { /* every second */ + putc('.'); + last = now; + } + } + + flash_reset(info); /* reset to read mode */ + } + + printf(" done\n"); + return rcode; +} + +/*----------------------------------------------------------------------- + * Copy memory to flash, returns: + * 0 - OK + * 1 - write timeout + * 2 - Flash not erased + */ +int +bad_write_buff(flash_info_t * info, uchar * src, ulong addr, ulong cnt) +{ + FPW data = 0; /* 16 or 32 bit word, matches flash bus width on MPC8XX */ + int bytes; /* number of bytes to program in current word */ + int left; /* number of bytes left to program */ + int i, res; + + for (left = cnt, res = 0; + left > 0 && res == 0; + addr += sizeof (data), left -= sizeof (data) - bytes) { + + bytes = addr & (sizeof (data) - 1); + addr &= ~(sizeof (data) - 1); + + /* combine source and destination data so can program + * an entire word of 16 or 32 bits + */ + for (i = 0; i < sizeof (data); i++) { + data <<= 8; + if (i < bytes || i - bytes >= left) + data += *((uchar *) addr + i); + else + data += *src++; + } + + /* write one word to the flash */ + switch (info->flash_id & FLASH_VENDMASK) { + case FLASH_MAN_AMD: + res = write_word_amd(info, (FPWV *) addr, data); + break; + case FLASH_MAN_INTEL: + res = write_word_intel(info, (FPWV *) addr, data); + break; + default: + /* unknown flash type, error! */ + printf("missing or unknown FLASH type\n"); + res = 1; /* not really a timeout, but gives error */ + break; + } + } + + return (res); +} + +/** + * write_buf: - Copy memory to flash. + * + * @param info: + * @param src: source of copy transaction + * @param addr: where to copy to + * @param cnt: number of bytes to copy + * + * @return error code + */ + +int +write_buff(flash_info_t * info, uchar * src, ulong addr, ulong cnt) +{ + ulong cp, wp; + FPW data; + int l; + int i, rc; + + wp = (addr & ~1); /* get lower word aligned address */ + + /* handle unaligned start bytes */ + if ((l = addr - wp) != 0) { + data = 0; + for (i = 0, cp = wp; i < l; ++i, ++cp) { + data = (data >> 8) | (*(uchar *) cp << 8); + } + for (; i < 2 && cnt > 0; ++i) { + data = (data >> 8) | (*src++ << 8); + --cnt; + ++cp; + } + for (; cnt == 0 && i < 2; ++i, ++cp) { + data = (data >> 8) | (*(uchar *) cp << 8); + } + + if ((rc = write_word(info, (FPWV *)wp, data)) != 0) { + return (rc); + } + wp += 2; + } + + /* handle word aligned part */ + while (cnt >= 2) { + /* data = *((vushort*)src); */ + data = *((FPW *) src); + if ((rc = write_word(info, (FPWV *)wp, data)) != 0) { + return (rc); + } + src += sizeof (FPW); + wp += sizeof (FPW); + cnt -= sizeof (FPW); + } + + if (cnt == 0) + return ERR_OK; + + /* + * handle unaligned tail bytes + */ + data = 0; + for (i = 0, cp = wp; i < 2 && cnt > 0; ++i, ++cp) { + data = (data >> 8) | (*src++ << 8); + --cnt; + } + for (; i < 2; ++i, ++cp) { + data = (data >> 8) | (*(uchar *) cp << 8); + } + + return write_word(info, (FPWV *)wp, data); +} + +/*----------------------------------------------------------------------- + * Write a word to Flash for AMD FLASH + * A word is 16 or 32 bits, whichever the bus width of the flash bank + * (not an individual chip) is. + * + * returns: + * 0 - OK + * 1 - write timeout + * 2 - Flash not erased + */ +static int +write_word_amd(flash_info_t * info, FPWV * dest, FPW data) +{ + ulong start; + int flag; + int res = 0; /* result, assume success */ + FPWV *base; /* first address in flash bank */ + + /* Check if Flash is (sufficiently) erased */ + if ((*dest & data) != data) { + return (2); + } + + base = (FPWV *) (info->start[0]); + /* Disable interrupts which might cause a timeout here */ + flag = disable_interrupts(); + + base[0x0555] = (FPW) 0x00AA00AA; /* unlock */ + base[0x02AA] = (FPW) 0x00550055; /* unlock */ + base[0x0555] = (FPW) 0x00A000A0; /* selects program mode */ + + *dest = data; /* start programming the data */ + + /* re-enable interrupts if necessary */ + if (flag) + enable_interrupts(); + + start = get_timer(0); + + /* data polling for D7 */ + while (res == 0 + && (*dest & (FPW) 0x00800080) != (data & (FPW) 0x00800080)) { + if (get_timer(0) - start > CFG_FLASH_WRITE_TOUT) { + *dest = (FPW) 0x00F000F0; /* reset bank */ + printf("SHA timeout\n"); + res = 1; + } + } + + return (res); +} + +/*----------------------------------------------------------------------- + * Write a word to Flash for Intel FLASH + * A word is 16 or 32 bits, whichever the bus width of the flash bank + * (not an individual chip) is. + * + * returns: + * 0 - OK + * 1 - write timeout + * 2 - Flash not erased + */ +static int +write_word_intel(flash_info_t * info, FPWV * dest, FPW data) +{ + ulong start; + int flag; + int res = 0; /* result, assume success */ + + /* Check if Flash is (sufficiently) erased */ + if ((*dest & data) != data) { + return (2); + } + + /* Disable interrupts which might cause a timeout here */ + flag = disable_interrupts(); + + *dest = (FPW) 0x00500050; /* clear status register */ + *dest = (FPW) 0x00FF00FF; /* make sure in read mode */ + *dest = (FPW) 0x00400040; /* program setup */ + + *dest = data; /* start programming the data */ + + /* re-enable interrupts if necessary */ + if (flag) + enable_interrupts(); + + start = get_timer(0); + + while (res == 0 && (*dest & (FPW) 0x00800080) != (FPW) 0x00800080) { + if (get_timer(start) > CFG_FLASH_WRITE_TOUT) { + *dest = (FPW) 0x00B000B0; /* Suspend program */ + res = 1; + } + } + + if (res == 0 && (*dest & (FPW) 0x00100010)) + res = 1; /* write failed, time out error is close enough */ + + *dest = (FPW) 0x00500050; /* clear status register */ + *dest = (FPW) 0x00FF00FF; /* make sure in read mode */ + + return (res); +} + +#ifdef CFG_FLASH_PROTECTION +/*----------------------------------------------------------------------- + */ +int +flash_real_protect(flash_info_t * info, long sector, int prot) +{ + int rcode = 0; /* assume success */ + FPWV *addr; /* address of sector */ + FPW value; + + addr = (FPWV *) (info->start[sector]); + + switch (info->flash_id & FLASH_TYPEMASK) { + case FLASH_28F800C3B: + case FLASH_28F800C3T: + case FLASH_28F160C3B: + case FLASH_28F160C3T: + case FLASH_28F320C3B: + case FLASH_28F320C3T: + case FLASH_28F640C3B: + case FLASH_28F640C3T: + flash_reset(info); /* make sure in read mode */ + *addr = (FPW) 0x00600060L; /* lock command setup */ + if (prot) + *addr = (FPW) 0x00010001L; /* lock sector */ + else + *addr = (FPW) 0x00D000D0L; /* unlock sector */ + flash_reset(info); /* reset to read mode */ + + /* now see if it really is locked/unlocked as requested */ + *addr = (FPW) 0x00900090; + /* read sector protection at sector address, (A7 .. A0) = 0x02. + * D0 = 1 for each device if protected. + * If at least one device is protected the sector is marked + * protected, but return failure. Mixed protected and + * unprotected devices within a sector should never happen. + */ + value = addr[2] & (FPW) 0x00010001; + if (value == 0) + info->protect[sector] = 0; + else if (value == (FPW) 0x00010001) + info->protect[sector] = 1; + else { + /* error, mixed protected and unprotected */ + rcode = 1; + info->protect[sector] = 1; + } + if (info->protect[sector] != prot) + rcode = 1; /* failed to protect/unprotect as requested */ + + /* reload all protection bits from hardware for now */ + flash_sync_real_protect(info); + break; + + case FLASH_AM640U: + default: + /* no hardware protect that we support */ + info->protect[sector] = prot; + break; + } + + return rcode; +} +#endif diff --git a/board/mx1fs2/intel.h b/board/mx1fs2/intel.h new file mode 100644 index 0000000000..8db5dd4f64 --- /dev/null +++ b/board/mx1fs2/intel.h @@ -0,0 +1,99 @@ +/* + * Copyright (C) 2002 ETC s.r.o. + * All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright + * notice, this list of conditions and the following disclaimer in the + * documentation and/or other materials provided with the distribution. + * 3. Neither the name of the ETC s.r.o. nor the names of its contributors + * may be used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" + * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE + * ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE + * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL + * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR + * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER + * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, + * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE + * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + * + * Written by Marcel Telka , 2002. + * + * Documentation: + * [1] Intel Corporation, "3 Volt Intel Strata Flash Memory 28F128J3A, 28F640J3A, + * 28F320J3A (x8/x16)", April 2002, Order Number: 290667-011 + * [2] Intel Corporation, "3 Volt Synchronous Intel Strata Flash Memory 28F640K3, 28F640K18, + * 28F128K3, 28F128K18, 28F256K3, 28F256K18 (x16)", June 2002, Order Number: 290737-005 + * + * This file is taken from OpenWinCE project hosted by SourceForge.net + * + */ + +#ifndef FLASH_INTEL_H +#define FLASH_INTEL_H + +#include + +/* Intel CFI commands - see Table 4. in [1] and Table 3. in [2] */ + +#define CFI_INTEL_CMD_READ_ARRAY 0xFF /* 28FxxxJ3A, 28FxxxK3, 28FxxxK18 */ +#define CFI_INTEL_CMD_READ_IDENTIFIER 0x90 /* 28FxxxJ3A, 28FxxxK3, 28FxxxK18 */ +#define CFI_INTEL_CMD_READ_QUERY 0x98 /* 28FxxxJ3A, 28FxxxK3, 28FxxxK18 */ +#define CFI_INTEL_CMD_READ_STATUS_REGISTER 0x70 /* 28FxxxJ3A, 28FxxxK3, 28FxxxK18 */ +#define CFI_INTEL_CMD_CLEAR_STATUS_REGISTER 0x50 /* 28FxxxJ3A, 28FxxxK3, 28FxxxK18 */ +#define CFI_INTEL_CMD_PROGRAM1 0x40 /* 28FxxxJ3A, 28FxxxK3, 28FxxxK18 */ +#define CFI_INTEL_CMD_PROGRAM2 0x10 /* 28FxxxJ3A, 28FxxxK3, 28FxxxK18 */ +#define CFI_INTEL_CMD_WRITE_TO_BUFFER 0xE8 /* 28FxxxJ3A, 28FxxxK3, 28FxxxK18 */ +#define CFI_INTEL_CMD_CONFIRM 0xD0 /* 28FxxxJ3A, 28FxxxK3, 28FxxxK18 */ +#define CFI_INTEL_CMD_BLOCK_ERASE 0x20 /* 28FxxxJ3A, 28FxxxK3, 28FxxxK18 */ +#define CFI_INTEL_CMD_SUSPEND 0xB0 /* 28FxxxJ3A, 28FxxxK3, 28FxxxK18 */ +#define CFI_INTEL_CMD_RESUME 0xD0 /* 28FxxxJ3A, 28FxxxK3, 28FxxxK18 */ +#define CFI_INTEL_CMD_LOCK_SETUP 0x60 /* 28FxxxJ3A, 28FxxxK3, 28FxxxK18 */ +#define CFI_INTEL_CMD_LOCK_BLOCK 0x01 /* 28FxxxJ3A, 28FxxxK3, 28FxxxK18 */ +#define CFI_INTEL_CMD_UNLOCK_BLOCK 0xD0 /* 28FxxxJ3A - unlocks all blocks, 28FFxxxK3, 28FxxxK18 */ +#define CFI_INTEL_CMD_LOCK_DOWN_BLOCK 0x2F /* 28FxxxK3, 28FxxxK18 */ + +/* Intel CFI Status Register bits - see Table 6. in [1] and Table 7. in [2] */ + +#define CFI_INTEL_SR_READY 1 << 7 /* 28FxxxJ3A, 28FxxxK3, 28FxxxK18 */ +#define CFI_INTEL_SR_ERASE_SUSPEND 1 << 6 /* 28FxxxJ3A, 28FxxxK3, 28FxxxK18 */ +#define CFI_INTEL_SR_ERASE_ERROR 1 << 5 /* 28FxxxJ3A, 28FxxxK3, 28FxxxK18 */ +#define CFI_INTEL_SR_PROGRAM_ERROR 1 << 4 /* 28FxxxJ3A, 28FxxxK3, 28FxxxK18 */ +#define CFI_INTEL_SR_VPEN_ERROR 1 << 3 /* 28FxxxJ3A, 28FxxxK3, 28FxxxK18 */ +#define CFI_INTEL_SR_PROGRAM_SUSPEND 1 << 2 /* 28FxxxJ3A, 28FxxxK3, 28FxxxK18 */ +#define CFI_INTEL_SR_BLOCK_LOCKED 1 << 1 /* 28FxxxJ3A, 28FxxxK3, 28FxxxK18 */ +#define CFI_INTEL_SR_BEFP 1 << 0 /* 28FxxxK3, 28FxxxK18 */ + +/* Intel flash device ID codes for 28FxxxJ3A - see Table 5. in [1] */ + +#define CFI_CHIP_INTEL_28F320J3A 0x0016 +#define CFI_CHIPN_INTEL_28F320J3A "28F320J3A" +#define CFI_CHIP_INTEL_28F640J3A 0x0017 +#define CFI_CHIPN_INTEL_28F640J3A "28F640J3A" +#define CFI_CHIP_INTEL_28F128J3A 0x0018 +#define CFI_CHIPN_INTEL_28F128J3A "28F128J3A" + +/* Intel flash device ID codes for 28FxxxK3 and 28FxxxK18 - see Table 8. in [2] */ + +#define CFI_CHIP_INTEL_28F640K3 0x8801 +#define CFI_CHIPN_INTEL_28F640K3 "28F640K3" +#define CFI_CHIP_INTEL_28F128K3 0x8802 +#define CFI_CHIPN_INTEL_28F128K3 "28F128K3" +#define CFI_CHIP_INTEL_28F256K3 0x8803 +#define CFI_CHIPN_INTEL_28F256K3 "28F256K3" +#define CFI_CHIP_INTEL_28F640K18 0x8805 +#define CFI_CHIPN_INTEL_28F640K18 "28F640K18" +#define CFI_CHIP_INTEL_28F128K18 0x8806 +#define CFI_CHIPN_INTEL_28F128K18 "28F128K18" +#define CFI_CHIP_INTEL_28F256K18 0x8807 +#define CFI_CHIPN_INTEL_28F256K18 "28F256K18" + +#endif /* FLASH_INTEL_H */ diff --git a/board/mx1fs2/memsetup.S b/board/mx1fs2/memsetup.S new file mode 100644 index 0000000000..5ec751b73d --- /dev/null +++ b/board/mx1fs2/memsetup.S @@ -0,0 +1,188 @@ +/* + * Copyright (C) 2004 Sascha Hauer, Pengutronix + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * as published by the Free Software Foundation; either version 2 + * of the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place - Suite 330, Boston, MA + * 02111-1307, USA. + * + */ + +#include +#include +#include + +.globl memsetup +memsetup: + + mov r10, lr + +/* Change PERCLK1DIV to 14 ie 14+1 */ + ldr r0, =PCDR + ldr r1, =CFG_PCDR_VAL + str r1, [r0] + +/* set MCU PLL Control Register 0 */ + + ldr r0, =MPCTL0 + ldr r1, =CFG_MPCTL0_VAL + str r1, [r0] + +/* set MCU PLL Control Register 1 */ + + ldr r0, =MPCTL1 + ldr r1, =CFG_MPCTL1_VAL + str r1, [r0] + +/* set mpll restart bit */ + ldr r0, =CSCR + ldr r1, [r0] + orr r1,r1,#(1<<21) + str r1, [r0] + + mov r2,#0x10 +1: + mov r3,#0x2000 +2: + subs r3,r3,#1 + bne 2b + + subs r2,r2,#1 + bne 1b + +/* set System PLL Control Register 0 */ + + ldr r0, =SPCTL0 + ldr r1, =CFG_SPCTL0_VAL + str r1, [r0] + +/* set System PLL Control Register 1 */ + + ldr r0, =SPCTL1 + ldr r1, =CFG_SPCTL1_VAL + str r1, [r0] + +/* set spll restart bit */ + ldr r0, =CSCR + ldr r1, [r0] + orr r1,r1,#(1<<22) + str r1, [r0] + + mov r2,#0x10 +1: + mov r3,#0x2000 +2: + subs r3,r3,#1 + bne 2b + + subs r2,r2,#1 + bne 1b + + ldr r0, =CSCR + ldr r1, =CFG_CSCR_VAL + str r1, [r0] + + ldr r0, =GPCR + ldr r1, =CFG_GPCR_VAL + str r1, [r0] + +/* + * I have now read the ARM920 DataSheet back-to-Back, and have stumbled upon + * this..... + * + * It would appear that from a Cold-Boot the ARM920T enters "FastBus" mode CP15 + * register 1, this stops it using the output of the PLL and thus runs at the + * slow rate. Unless you place the Core into "Asynch" mode, the CPU will never + * use the value set in the CM_OSC registers...regardless of what you set it + * too! Thus, although i thought i was running at 140MHz, i'm actually running + * at 40!.. + * + * Slapping this into my bootloader does the trick... + * + * MRC p15,0,r0,c1,c0,0 ; read core configuration register + * ORR r0,r0,#0xC0000000 ; set asynchronous clocks and not fastbus mode + * MCR p15,0,r0,c1,c0,0 ; write modified value to core configuration + * register + * + */ + MRC p15,0,r0,c1,c0,0 +/* ORR r0,r0,#0xC0000000 async mode */ +/* ORR r0,r0,#0x40000000 sync mode */ + ORR r0,r0,#0xC0000000 + MCR p15,0,r0,c1,c0,0 + + ldr r0, =GIUS(0) + ldr r1, =CFG_GIUS_A_VAL + str r1, [r0] + + ldr r0, =FMCR + ldr r1, =CFG_FMCR_VAL + str r1, [r0] + + ldr r0, =CS0U + ldr r1, =CFG_CS0U_VAL + str r1, [r0] + + ldr r0, =CS0L + ldr r1, =CFG_CS0L_VAL + str r1, [r0] + + ldr r0, =CS1U + ldr r1, =CFG_CS1U_VAL + str r1, [r0] + + ldr r0, =CS1L + ldr r1, =CFG_CS1L_VAL + str r1, [r0] + + ldr r0, =CS4U + ldr r1, =CFG_CS4U_VAL + str r1, [r0] + + ldr r0, =CS4L + ldr r1, =CFG_CS4L_VAL + str r1, [r0] + + ldr r0, =CS5U + ldr r1, =CFG_CS5U_VAL + str r1, [r0] + + ldr r0, =CS5L + ldr r1, =CFG_CS5L_VAL + str r1, [r0] + +/* SDRAM Setup */ + + ldr r1,=0x00221000 /* adr of SDCTRL0 */ + ldr r0,=0x92120200 + str r0,[r1,#0] /* put in precharge command mode */ + ldr r2,=0x08200000 /* adr for precharge cmd */ + ldr r0,[r2,#0] /* precharge */ + ldr r0,=0xA2120200 + ldr r2,=0x08000000 /* start of SDRAM */ + str r0,[r1,#0] /* put in auto-refresh mode */ + ldr r0,[r2,#0] /* auto-refresh */ + ldr r0,[r2,#0] /* auto-refresh */ + ldr r0,[r2,#0] /* auto-refresh */ + ldr r0,[r2,#0] /* auto-refresh */ + ldr r0,[r2,#0] /* auto-refresh */ + ldr r0,[r2,#0] /* auto-refresh */ + ldr r0,[r2,#0] /* auto-refresh */ + ldr r0,=0xB2120200 + ldr r2,=0x08111800 + str r0,[r1,#0] /* setup for mode register of SDRAM */ + ldr r0,[r2,#0] /* program mode register */ + ldr r0,=0x82124267 + str r0,[r1,#0] /* back to normal operation */ + + mov pc,r10 diff --git a/board/mx1fs2/mx1fs2.c b/board/mx1fs2/mx1fs2.c new file mode 100644 index 0000000000..f51085a979 --- /dev/null +++ b/board/mx1fs2/mx1fs2.c @@ -0,0 +1,125 @@ +/* + * Copyright (C) 2004 Sascha Hauer, Pengutronix + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + * + */ + +#include + +#include + +#define SHOW_BOOT_PROGRESS(arg) show_boot_progress(arg) + +extern void imx_gpio_mode(int gpio_mode); + +static void logo_init(void) +{ + imx_gpio_mode(PD15_PF_LD0); + imx_gpio_mode(PD16_PF_LD1); + imx_gpio_mode(PD17_PF_LD2); + imx_gpio_mode(PD18_PF_LD3); + imx_gpio_mode(PD19_PF_LD4); + imx_gpio_mode(PD20_PF_LD5); + imx_gpio_mode(PD21_PF_LD6); + imx_gpio_mode(PD22_PF_LD7); + imx_gpio_mode(PD23_PF_LD8); + imx_gpio_mode(PD24_PF_LD9); + imx_gpio_mode(PD25_PF_LD10); + imx_gpio_mode(PD26_PF_LD11); + imx_gpio_mode(PD27_PF_LD12); + imx_gpio_mode(PD28_PF_LD13); + imx_gpio_mode(PD29_PF_LD14); + imx_gpio_mode(PD30_PF_LD15); + imx_gpio_mode(PD14_PF_FLM_VSYNC); + imx_gpio_mode(PD13_PF_LP_HSYNC); + imx_gpio_mode(PD6_PF_LSCLK); + imx_gpio_mode(GPIO_PORTD | GPIO_OUT | GPIO_GPIO); + imx_gpio_mode(PD11_PF_CONTRAST); + imx_gpio_mode(PD10_PF_SPL_SPR); + + LCDC_RMCR = 0x00000000; + LCDC_PCR = PCR_COLOR | PCR_PBSIZ_8 | PCR_BPIX_16 | PCR_PCD(5); + LCDC_HCR = HCR_H_WIDTH(2); + LCDC_VCR = VCR_V_WIDTH(2); + + LCDC_PWMR = 0x00000380; /* contrast to 0x80 middle (is best !!!) */ + LCDC_SSA = 0x10040000; /* image in flash */ + + LCDC_SIZE = SIZE_XMAX(320) | SIZE_YMAX(240); /* screen size */ + + LCDC_VPW = 0x000000A0; /* Virtual Page Width Register */ + LCDC_POS = 0x00000000; /* panning offset 0 (0 pixel offset) */ + + /* disable Cursor */ + LCDC_CPOS = 0x00000000; + + /* fixed burst length */ + LCDC_DMACR = DMACR_BURST | DMACR_HM(8) | DMACR_TM(2); + + /* enable LCD */ + DR(3) |= 0x00001000; + LCDC_RMCR = RMCR_LCDC_EN; + +} + +int +board_init(void) +{ + DECLARE_GLOBAL_DATA_PTR; + + gd->bd->bi_arch_number = 470; + gd->bd->bi_boot_params = 0x08000100; +serial_init(); + logo_init(); + return 0; +} + +int +dram_init(void) +{ + DECLARE_GLOBAL_DATA_PTR; + +#if ( CONFIG_NR_DRAM_BANKS > 0 ) + gd->bd->bi_dram[0].start = MX1FS2_SDRAM_1; + gd->bd->bi_dram[0].size = MX1FS2_SDRAM_1_SIZE; +#endif + return 0; +} + +/** + * show_boot_progress: - indicate state of the boot process + * + * @param status: Status number - see README for details. + * + */ + +void +show_boot_progress(int status) +{ + /* We use this as a hook to disable serial ports just before booting + * This way we suppress the "uncompressing linux..." message + */ +#ifdef CONFIG_SILENT_CONSOLE + if( status == 8) { + if( getenv("silent") != NULL ) { + *(volatile unsigned long *)0x206080 &= ~1; + *(volatile unsigned long *)0x207080 &= ~1; + } + } +#endif + return; +} diff --git a/board/mx1fs2/u-boot.lds b/board/mx1fs2/u-boot.lds new file mode 100644 index 0000000000..5076303c7e --- /dev/null +++ b/board/mx1fs2/u-boot.lds @@ -0,0 +1,56 @@ +/* + * (C) Copyright 2000-2004 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + * + */ + +OUTPUT_FORMAT("elf32-littlearm", "elf32-littlearm", "elf32-littlearm") +OUTPUT_ARCH(arm) +ENTRY(_start) +SECTIONS +{ + . = 0x00000000; + + . = ALIGN(4); + .text : + { + cpu/arm920t/start.o (.text) + *(.text) + } + + . = ALIGN(4); + .rodata : { *(.rodata) } + + . = ALIGN(4); + .data : { *(.data) } + + . = ALIGN(4); + .got : { *(.got) } + + __u_boot_cmd_start = .; + .u_boot_cmd : { *(.u_boot_cmd) } + __u_boot_cmd_end = .; + + . = ALIGN(4); + __bss_start = .; + .bss : { *(.bss) } + _end = .; +} diff --git a/board/netphone/phone_console.c b/board/netphone/phone_console.c index dd59969378..408ada0169 100644 --- a/board/netphone/phone_console.c +++ b/board/netphone/phone_console.c @@ -326,7 +326,6 @@ int phone_getc(void) int drv_phone_init(void) { device_t console_dev; - char *penv; console_init(); diff --git a/board/sbc8560/sbc8560.c b/board/sbc8560/sbc8560.c index a784e3426a..1aed61b6dd 100644 --- a/board/sbc8560/sbc8560.c +++ b/board/sbc8560/sbc8560.c @@ -256,11 +256,13 @@ long int initdram (int board_type) long dram_size = 0; extern long spd_sdram (void); volatile immap_t *immap = (immap_t *)CFG_IMMR; +#if 0 #if !defined(CONFIG_RAM_AS_FLASH) volatile ccsr_lbc_t *lbc= &immap->im_lbc; sys_info_t sysinfo; uint temp_lbcdll = 0; #endif +#endif /* 0 */ #if !defined(CONFIG_RAM_AS_FLASH) || defined(CONFIG_DDR_DLL) volatile ccsr_gur_t *gur= &immap->im_gur; #endif @@ -279,7 +281,7 @@ long int initdram (int board_type) dram_size = fixed_sdram (); #endif -#if XXX +#if 0 #if !defined(CONFIG_RAM_AS_FLASH) /* LocalBus SDRAM is not emulating flash */ get_sys_info(&sysinfo); /* if localbus freq is less than 66Mhz,we use bypass mode,otherwise use DLL */ diff --git a/cpu/mc9328/config.mk b/board/scb9328/Makefile similarity index 57% rename from cpu/mc9328/config.mk rename to board/scb9328/Makefile index cef7d26f1c..212efcc4e5 100644 --- a/cpu/mc9328/config.mk +++ b/board/scb9328/Makefile @@ -1,6 +1,6 @@ # -# (C) Copyright 2002 -# Gary Jennejohn, DENX Software Engineering, +# (C) Copyright 2000-2004 +# Wolfgang Denk, DENX Software Engineering, wd@denx.de. # # See file CREDITS for list of people who contributed to this # project. @@ -21,7 +21,27 @@ # MA 02111-1307 USA # -PLATFORM_RELFLAGS += -fno-strict-aliasing -fno-common -ffixed-r8 \ - -mshort-load-bytes -msoft-float +include $(TOPDIR)/config.mk -PLATFORM_CPPFLAGS += -mapcs-32 -march=armv4 +LIB = lib$(BOARD).a + +OBJS := scb9328.o flash.o +SOBJS := memsetup.o + +$(LIB): $(OBJS) $(SOBJS) + $(AR) crv $@ $^ + +clean: + rm -f $(SOBJS) $(OBJS) + +distclean: clean + rm -f $(LIB) core *.bak .depend + +######################################################################### + +.depend: Makefile $(SOBJS:.o=.S) $(OBJS:.o=.c) + $(CC) -M $(CPPFLAGS) $(SOBJS:.o=.S) $(OBJS:.o=.c) > $@ + +-include .depend + +######################################################################### diff --git a/board/scb9328/config.mk b/board/scb9328/config.mk new file mode 100644 index 0000000000..8d1d79ac90 --- /dev/null +++ b/board/scb9328/config.mk @@ -0,0 +1,10 @@ +# +# This config file is used for compilation of scb93328 sources +# +# You might change location of U-Boot in memory by setting right TEXT_BASE. +# This allows for example having one copy located at the end of ram and stored +# in flash device and later on while developing use other location to test +# the code in RAM device only. +# + +TEXT_BASE = 0x08f00000 diff --git a/board/scb9328/flash.c b/board/scb9328/flash.c new file mode 100644 index 0000000000..1b56f8c6aa --- /dev/null +++ b/board/scb9328/flash.c @@ -0,0 +1,321 @@ +/* + * Copyright (C) 2003 ETC s.r.o. + * + * This code was inspired by Marius Groeger and Kyle Harris code + * available in other board ports for U-Boot + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + * + * Written by Peter Figuli , 2003. + * + */ + +#include +#include "intel.h" + + +/* + * This code should handle CFI FLASH memory device. This code is very + * minimalistic approach without many essential error handling code as well. + * Because U-Boot actually is missing smart handling of FLASH device, + * we just set flash_id to anything else to FLASH_UNKNOW, so common code + * can call us without any restrictions. + * TODO: Add CFI Query, to be able to determine FLASH device. + * TODO: Add error handling code + * NOTE: This code was tested with BUS_WIDTH 4 and ITERLEAVE 2 only, but + * hopefully may work with other configurations. + */ + +#if ( SCB9328_FLASH_BUS_WIDTH == 1 ) +# define FLASH_BUS vu_char +# if ( SCB9328_FLASH_INTERLEAVE == 1 ) +# define FLASH_CMD( x ) x +# else +# error "With 8bit bus only one chip is allowed" +# endif + + +#elif ( SCB9328_FLASH_BUS_WIDTH == 2 ) +# define FLASH_BUS vu_short +# if ( SCB9328_FLASH_INTERLEAVE == 1 ) +# define FLASH_CMD( x ) x +# elif ( SCB9328_FLASH_INTERLEAVE == 2 ) +# define FLASH_CMD( x ) (( x << 8 )| x ) +# else +# error "With 16bit bus only 1 or 2 chip(s) are allowed" +# endif + + +#elif ( SCB9328_FLASH_BUS_WIDTH == 4 ) +# define FLASH_BUS vu_long +# if ( SCB9328_FLASH_INTERLEAVE == 1 ) +# define FLASH_CMD( x ) x +# elif ( SCB9328_FLASH_INTERLEAVE == 2 ) +# define FLASH_CMD( x ) (( x << 16 )| x ) +# elif ( SCB9328_FLASH_INTERLEAVE == 4 ) +# define FLASH_CMD( x ) (( x << 24 )|( x << 16 ) ( x << 8 )| x ) +# else +# error "With 32bit bus only 1,2 or 4 chip(s) are allowed" +# endif + +#else +# error "Flash bus width might be 1,2,4 for 8,16,32 bit configuration" +#endif + + +flash_info_t flash_info[CFG_MAX_FLASH_BANKS]; + +static FLASH_BUS flash_status_reg (void) +{ + + FLASH_BUS *addr = (FLASH_BUS *) 0; + + *addr = FLASH_CMD (CFI_INTEL_CMD_READ_STATUS_REGISTER); + + return *addr; +} + +static int flash_ready (ulong timeout) +{ + int ok = 1; + + reset_timer_masked (); + while ((flash_status_reg () & FLASH_CMD (CFI_INTEL_SR_READY)) != + FLASH_CMD (CFI_INTEL_SR_READY)) { + if (get_timer_masked () > timeout && timeout != 0) { + ok = 0; + break; + } + } + return ok; +} + +#if ( CFG_MAX_FLASH_BANKS != 1 ) +# error "SCB9328 platform has only one flash bank!" +#endif + + +ulong flash_init (void) +{ + int i; + unsigned long address = SCB9328_FLASH_BASE; + + flash_info[0].size = SCB9328_FLASH_BANK_SIZE; + flash_info[0].sector_count = CFG_MAX_FLASH_SECT; + flash_info[0].flash_id = INTEL_MANUFACT; + memset (flash_info[0].protect, 0, CFG_MAX_FLASH_SECT); + + for (i = 0; i < CFG_MAX_FLASH_SECT; i++) { + flash_info[0].start[i] = address; +#ifdef SCB9328_FLASH_UNLOCK + /* Some devices are hw locked after start. */ + *((FLASH_BUS *) address) = FLASH_CMD (CFI_INTEL_CMD_LOCK_SETUP); + *((FLASH_BUS *) address) = FLASH_CMD (CFI_INTEL_CMD_UNLOCK_BLOCK); + flash_ready (0); + *((FLASH_BUS *) address) = FLASH_CMD (CFI_INTEL_CMD_READ_ARRAY); +#endif + address += SCB9328_FLASH_SECT_SIZE; + } + + flash_protect (FLAG_PROTECT_SET, + CFG_FLASH_BASE, + CFG_FLASH_BASE + monitor_flash_len - 1, + &flash_info[0]); + + flash_protect (FLAG_PROTECT_SET, + CFG_ENV_ADDR, + CFG_ENV_ADDR + CFG_ENV_SIZE - 1, &flash_info[0]); + + return SCB9328_FLASH_BANK_SIZE; +} + +void flash_print_info (flash_info_t * info) +{ + int i; + + printf (" Intel vendor\n"); + printf (" Size: %ld MB in %d Sectors\n", + info->size >> 20, info->sector_count); + + printf (" Sector Start Addresses:"); + for (i = 0; i < info->sector_count; i++) { + if (!(i % 5)) { + printf ("\n"); + } + + printf (" %08lX%s", info->start[i], + info->protect[i] ? " (RO)" : " "); + } + printf ("\n"); +} + + +int flash_erase (flash_info_t * info, int s_first, int s_last) +{ + int flag, non_protected = 0, sector; + int rc = ERR_OK; + + FLASH_BUS *address; + + for (sector = s_first; sector <= s_last; sector++) { + if (!info->protect[sector]) { + non_protected++; + } + } + + if (!non_protected) { + return ERR_PROTECTED; + } + + /* + * Disable interrupts which might cause a timeout + * here. Remember that our exception vectors are + * at address 0 in the flash, and we don't want a + * (ticker) exception to happen while the flash + * chip is in programming mode. + */ + flag = disable_interrupts (); + + + /* Start erase on unprotected sectors */ + for (sector = s_first; sector <= s_last && !ctrlc (); sector++) { + if (info->protect[sector]) { + printf ("Protected sector %2d skipping...\n", sector); + continue; + } else { + printf ("Erasing sector %2d ... ", sector); + } + + address = (FLASH_BUS *) (info->start[sector]); + + *address = FLASH_CMD (CFI_INTEL_CMD_BLOCK_ERASE); + *address = FLASH_CMD (CFI_INTEL_CMD_CONFIRM); + if (flash_ready (CFG_FLASH_ERASE_TOUT)) { + *address = FLASH_CMD (CFI_INTEL_CMD_CLEAR_STATUS_REGISTER); + printf ("ok.\n"); + } else { + *address = FLASH_CMD (CFI_INTEL_CMD_SUSPEND); + rc = ERR_TIMOUT; + printf ("timeout! Aborting...\n"); + break; + } + *address = FLASH_CMD (CFI_INTEL_CMD_READ_ARRAY); + } + if (ctrlc ()) + printf ("User Interrupt!\n"); + + /* allow flash to settle - wait 10 ms */ + udelay_masked (10000); + if (flag) { + enable_interrupts (); + } + + return rc; +} + +static int write_data (flash_info_t * info, ulong dest, FLASH_BUS data) +{ + FLASH_BUS *address = (FLASH_BUS *) dest; + int rc = ERR_OK; + int flag; + + /* Check if Flash is (sufficiently) erased */ + if ((*address & data) != data) { + return ERR_NOT_ERASED; + } + + /* + * Disable interrupts which might cause a timeout + * here. Remember that our exception vectors are + * at address 0 in the flash, and we don't want a + * (ticker) exception to happen while the flash + * chip is in programming mode. + */ + + flag = disable_interrupts (); + + *address = FLASH_CMD (CFI_INTEL_CMD_CLEAR_STATUS_REGISTER); + *address = FLASH_CMD (CFI_INTEL_CMD_PROGRAM1); + *address = data; + + if (!flash_ready (CFG_FLASH_WRITE_TOUT)) { + *address = FLASH_CMD (CFI_INTEL_CMD_SUSPEND); + rc = ERR_TIMOUT; + printf ("timeout! Aborting...\n"); + } + + *address = FLASH_CMD (CFI_INTEL_CMD_READ_ARRAY); + if (flag) { + enable_interrupts (); + } + + return rc; +} + +int write_buff (flash_info_t * info, uchar * src, ulong addr, ulong cnt) +{ + ulong read_addr, write_addr; + FLASH_BUS data; + int i, result = ERR_OK; + + + read_addr = addr & ~(sizeof (FLASH_BUS) - 1); + write_addr = read_addr; + if (read_addr != addr) { + data = 0; + for (i = 0; i < sizeof (FLASH_BUS); i++) { + if (read_addr < addr || cnt == 0) { + data |= *((uchar *) read_addr) << i * 8; + } else { + data |= (*src++) << i * 8; + cnt--; + } + read_addr++; + } + if ((result = write_data (info, write_addr, data)) != ERR_OK) { + return result; + } + write_addr += sizeof (FLASH_BUS); + } + for (; cnt >= sizeof (FLASH_BUS); cnt -= sizeof (FLASH_BUS)) { + if ((result = write_data (info, write_addr, + *((FLASH_BUS *) src))) != ERR_OK) { + return result; + } + write_addr += sizeof (FLASH_BUS); + src += sizeof (FLASH_BUS); + } + if (cnt > 0) { + read_addr = write_addr; + data = 0; + for (i = 0; i < sizeof (FLASH_BUS); i++) { + if (cnt > 0) { + data |= (*src++) << i * 8; + cnt--; + } else { + data |= *((uchar *) read_addr) << i * 8; + } + read_addr++; + } + if ((result = write_data (info, write_addr, data)) != 0) { + return result; + } + } + return ERR_OK; +} diff --git a/board/scb9328/intel.h b/board/scb9328/intel.h new file mode 100644 index 0000000000..77498b6e1d --- /dev/null +++ b/board/scb9328/intel.h @@ -0,0 +1,99 @@ +/* + * Copyright (C) 2002 ETC s.r.o. + * All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright + * notice, this list of conditions and the following disclaimer in the + * documentation and/or other materials provided with the distribution. + * 3. Neither the name of the ETC s.r.o. nor the names of its contributors + * may be used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" + * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE + * ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE + * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL + * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR + * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER + * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, + * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE + * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + * + * Written by Marcel Telka , 2002. + * + * Documentation: + * [1] Intel Corporation, "3 Volt Intel Strata Flash Memory 28F128J3A, 28F640J3A, + * 28F320J3A (x8/x16)", April 2002, Order Number: 290667-011 + * [2] Intel Corporation, "3 Volt Synchronous Intel Strata Flash Memory 28F640K3, 28F640K18, + * 28F128K3, 28F128K18, 28F256K3, 28F256K18 (x16)", June 2002, Order Number: 290737-005 + * + * This file is taken from OpenWinCE project hosted by SourceForge.net + * + */ + +#ifndef FLASH_INTEL_H +#define FLASH_INTEL_H + +#include + +/* Intel CFI commands - see Table 4. in [1] and Table 3. in [2] */ + +#define CFI_INTEL_CMD_READ_ARRAY 0xFF /* 28FxxxJ3A, 28FxxxK3, 28FxxxK18 */ +#define CFI_INTEL_CMD_READ_IDENTIFIER 0x90 /* 28FxxxJ3A, 28FxxxK3, 28FxxxK18 */ +#define CFI_INTEL_CMD_READ_QUERY 0x98 /* 28FxxxJ3A, 28FxxxK3, 28FxxxK18 */ +#define CFI_INTEL_CMD_READ_STATUS_REGISTER 0x70 /* 28FxxxJ3A, 28FxxxK3, 28FxxxK18 */ +#define CFI_INTEL_CMD_CLEAR_STATUS_REGISTER 0x50 /* 28FxxxJ3A, 28FxxxK3, 28FxxxK18 */ +#define CFI_INTEL_CMD_PROGRAM1 0x40 /* 28FxxxJ3A, 28FxxxK3, 28FxxxK18 */ +#define CFI_INTEL_CMD_PROGRAM2 0x10 /* 28FxxxJ3A, 28FxxxK3, 28FxxxK18 */ +#define CFI_INTEL_CMD_WRITE_TO_BUFFER 0xE8 /* 28FxxxJ3A, 28FxxxK3, 28FxxxK18 */ +#define CFI_INTEL_CMD_CONFIRM 0xD0 /* 28FxxxJ3A, 28FxxxK3, 28FxxxK18 */ +#define CFI_INTEL_CMD_BLOCK_ERASE 0x20 /* 28FxxxJ3A, 28FxxxK3, 28FxxxK18 */ +#define CFI_INTEL_CMD_SUSPEND 0xB0 /* 28FxxxJ3A, 28FxxxK3, 28FxxxK18 */ +#define CFI_INTEL_CMD_RESUME 0xD0 /* 28FxxxJ3A, 28FxxxK3, 28FxxxK18 */ +#define CFI_INTEL_CMD_LOCK_SETUP 0x60 /* 28FxxxJ3A, 28FxxxK3, 28FxxxK18 */ +#define CFI_INTEL_CMD_LOCK_BLOCK 0x01 /* 28FxxxJ3A, 28FxxxK3, 28FxxxK18 */ +#define CFI_INTEL_CMD_UNLOCK_BLOCK 0xD0 /* 28FxxxJ3A - unlocks all blocks, 28FFxxxK3, 28FxxxK18 */ +#define CFI_INTEL_CMD_LOCK_DOWN_BLOCK 0x2F /* 28FxxxK3, 28FxxxK18 */ + +/* Intel CFI Status Register bits - see Table 6. in [1] and Table 7. in [2] */ + +#define CFI_INTEL_SR_READY 1 << 7 /* 28FxxxJ3A, 28FxxxK3, 28FxxxK18 */ +#define CFI_INTEL_SR_ERASE_SUSPEND 1 << 6 /* 28FxxxJ3A, 28FxxxK3, 28FxxxK18 */ +#define CFI_INTEL_SR_ERASE_ERROR 1 << 5 /* 28FxxxJ3A, 28FxxxK3, 28FxxxK18 */ +#define CFI_INTEL_SR_PROGRAM_ERROR 1 << 4 /* 28FxxxJ3A, 28FxxxK3, 28FxxxK18 */ +#define CFI_INTEL_SR_VPEN_ERROR 1 << 3 /* 28FxxxJ3A, 28FxxxK3, 28FxxxK18 */ +#define CFI_INTEL_SR_PROGRAM_SUSPEND 1 << 2 /* 28FxxxJ3A, 28FxxxK3, 28FxxxK18 */ +#define CFI_INTEL_SR_BLOCK_LOCKED 1 << 1 /* 28FxxxJ3A, 28FxxxK3, 28FxxxK18 */ +#define CFI_INTEL_SR_BEFP 1 << 0 /* 28FxxxK3, 28FxxxK18 */ + +/* Intel flash device ID codes for 28FxxxJ3A - see Table 5. in [1] */ + +#define CFI_CHIP_INTEL_28F320J3A 0x0016 +#define CFI_CHIPN_INTEL_28F320J3A "28F320J3A" +#define CFI_CHIP_INTEL_28F640J3A 0x0017 +#define CFI_CHIPN_INTEL_28F640J3A "28F640J3A" +#define CFI_CHIP_INTEL_28F128J3A 0x0018 +#define CFI_CHIPN_INTEL_28F128J3A "28F128J3A" + +/* Intel flash device ID codes for 28FxxxK3 and 28FxxxK18 - see Table 8. in [2] */ + +#define CFI_CHIP_INTEL_28F640K3 0x8801 +#define CFI_CHIPN_INTEL_28F640K3 "28F640K3" +#define CFI_CHIP_INTEL_28F128K3 0x8802 +#define CFI_CHIPN_INTEL_28F128K3 "28F128K3" +#define CFI_CHIP_INTEL_28F256K3 0x8803 +#define CFI_CHIPN_INTEL_28F256K3 "28F256K3" +#define CFI_CHIP_INTEL_28F640K18 0x8805 +#define CFI_CHIPN_INTEL_28F640K18 "28F640K18" +#define CFI_CHIP_INTEL_28F128K18 0x8806 +#define CFI_CHIPN_INTEL_28F128K18 "28F128K18" +#define CFI_CHIP_INTEL_28F256K18 0x8807 +#define CFI_CHIPN_INTEL_28F256K18 "28F256K18" + +#endif /* FLASH_INTEL_H */ diff --git a/board/scb9328/memsetup.S b/board/scb9328/memsetup.S new file mode 100644 index 0000000000..be5650a45f --- /dev/null +++ b/board/scb9328/memsetup.S @@ -0,0 +1,203 @@ +/* + * Copyright (C) 2004 Sascha Hauer, Synertronixx GmbH + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * as published by the Free Software Foundation; either version 2 + * of the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place - Suite 330, Boston, MA + * 02111-1307, USA. + * + */ + +#include +#include +#include + +.globl memsetup +memsetup: + + mov r10, lr + +/* Change PERCLK1DIV to 14 ie 14+1 */ + ldr r0, =PCDR + ldr r1, =CFG_PCDR_VAL + str r1, [r0] + +/* set MCU PLL Control Register 0 */ + + ldr r0, =MPCTL0 + ldr r1, =CFG_MPCTL0_VAL + str r1, [r0] + +/* set mpll restart bit */ + ldr r0, =CSCR + ldr r1, [r0] + orr r1,r1,#(1<<21) + str r1, [r0] + + mov r2,#0x10 +1: + mov r3,#0x2000 +2: + subs r3,r3,#1 + bne 2b + + subs r2,r2,#1 + bne 1b + +/* set System PLL Control Register 0 */ + + ldr r0, =SPCTL0 + ldr r1, =CFG_SPCTL0_VAL + str r1, [r0] + +/* set spll restart bit */ + ldr r0, =CSCR + ldr r1, [r0] + orr r1,r1,#(1<<22) + str r1, [r0] + + mov r2,#0x10 +1: + mov r3,#0x2000 +2: + subs r3,r3,#1 + bne 2b + + subs r2,r2,#1 + bne 1b + + ldr r0, =CSCR + ldr r1, =CFG_CSCR_VAL + str r1, [r0] + +/* I have now read the ARM920 DataSheet back-to-Back, and have stumbled upon + *this..... + * + * It would appear that from a Cold-Boot the ARM920T enters "FastBus" mode CP15 + * register 1, this stops it using the output of the PLL and thus runs at the + * slow rate. Unless you place the Core into "Asynch" mode, the CPU will never + * use the value set in the CM_OSC registers...regardless of what you set it + * too! Thus, although i thought i was running at 140MHz, i'm actually running + * at 40!.. + + * Slapping this into my bootloader does the trick... + + * MRC p15,0,r0,c1,c0,0 ; read core configuration register + * ORR r0,r0,#0xC0000000 ; set asynchronous clocks and not fastbus mode + * MCR p15,0,r0,c1,c0,0 ; write modified value to core configuration + * register + */ + MRC p15,0,r0,c1,c0,0 + ORR r0,r0,#0xC0000000 + MCR p15,0,r0,c1,c0,0 + + ldr r0, =GPR(0) + ldr r1, =CFG_GPR_A_VAL + str r1, [r0] + + ldr r0, =GIUS(0) + ldr r1, =CFG_GIUS_A_VAL + str r1, [r0] + +/* CS3 becomes CS3 by clearing reset default bit 1 in FMCR */ + + ldr r0, =FMCR + ldr r1, =CFG_FMCR_VAL + str r1, [r0] + + ldr r0, =CS0U + ldr r1, =CFG_CS0U_VAL + str r1, [r0] + + ldr r0, =CS0L + ldr r1, =CFG_CS0L_VAL + str r1, [r0] + + ldr r0, =CS1U + ldr r1, =CFG_CS1U_VAL + str r1, [r0] + + ldr r0, =CS1L + ldr r1, =CFG_CS1L_VAL + str r1, [r0] + + ldr r0, =CS2U + ldr r1, =CFG_CS2U_VAL + str r1, [r0] + + ldr r0, =CS2L + ldr r1, =CFG_CS2L_VAL + str r1, [r0] + + ldr r0, =CS3U + ldr r1, =CFG_CS3U_VAL + str r1, [r0] + + ldr r0, =CS3L + ldr r1, =CFG_CS3L_VAL + str r1, [r0] + + ldr r0, =CS4U + ldr r1, =CFG_CS4U_VAL + str r1, [r0] + + ldr r0, =CS4L + ldr r1, =CFG_CS4L_VAL + str r1, [r0] + + ldr r0, =CS5U + ldr r1, =CFG_CS5U_VAL + str r1, [r0] + + ldr r0, =CS5L + ldr r1, =CFG_CS5L_VAL + str r1, [r0] + +/* SDRAM Setup */ + + ldr r0, =SDCTL0 + ldr r1, =PRECHARGE_CMD + str r1, [r0] + + ldr r0, =0x08200000 + ldr r1, =0x0 /* Issue Precharge all Command */ + str r1, [r0] + + ldr r0, =SDCTL0 + ldr r1, =AUTOREFRESH_CMD + str r1, [r0] + + ldr r0, =0x08000000 + ldr r1, =0x0 /* Issue AutoRefresh Command */ + str r1, [r0] + str r1, [r0] + str r1, [r0] + str r1, [r0] + str r1, [r0] + str r1, [r0] + str r1, [r0] + str r1, [r0] + + ldr r0, =SDCTL0 + ldr r1, =0xb10a8300 + str r1, [r0] + + ldr r0, =0x08223000 /* CAS Latency 2 */ + ldr r1, =0x0 /* Issue Mode Register Command, Burst Length = 8 */ + str r1, [r0] + + ldr r0, =SDCTL0 + ldr r1, =0x810a8200 /* Set to Normal Mode CAS 2 */ + str r1, [r0] + + mov pc,r10 diff --git a/board/scb9328/scb9328.c b/board/scb9328/scb9328.c new file mode 100644 index 0000000000..a1fe0aefeb --- /dev/null +++ b/board/scb9328/scb9328.c @@ -0,0 +1,73 @@ +/* + * Copyright (C) 2004 Sascha Hauer, Synertronixx GmbH + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + * + */ + +#include + +#ifdef CONFIG_SHOW_BOOT_PROGRESS +# define SHOW_BOOT_PROGRESS(arg) show_boot_progress(arg) +#else +# define SHOW_BOOT_PROGRESS(arg) +#endif + +int board_init( void ){ + DECLARE_GLOBAL_DATA_PTR; + + gd->bd->bi_arch_number = 508; + gd->bd->bi_boot_params = 0x08000100; + + return 0; +} + +int dram_init( void ){ + DECLARE_GLOBAL_DATA_PTR; + +#if ( CONFIG_NR_DRAM_BANKS > 0 ) + gd->bd->bi_dram[0].start = SCB9328_SDRAM_1; + gd->bd->bi_dram[0].size = SCB9328_SDRAM_1_SIZE; +#endif +#if ( CONFIG_NR_DRAM_BANKS > 1 ) + gd->bd->bi_dram[1].start = SCB9328_SDRAM_2; + gd->bd->bi_dram[1].size = SCB9328_SDRAM_2_SIZE; +#endif +#if ( CONFIG_NR_DRAM_BANKS > 2 ) + gd->bd->bi_dram[2].start = SCB9328_SDRAM_3; + gd->bd->bi_dram[2].size = SCB9328_SDRAM_3_SIZE; +#endif +#if ( CONFIG_NR_DRAM_BANKS > 3 ) + gd->bd->bi_dram[3].start = SCB9328_SDRAM_4; + gd->bd->bi_dram[3].size = SCB9328_SDRAM_4_SIZE; +#endif + + return 0; +} + +/** + * show_boot_progress: - indicate state of the boot process + * + * @param status: Status number - see README for details. + * + * The CSB226 does only have 3 LEDs, so we switch them on at the most + * important states (1, 5, 15). + */ + +void show_boot_progress (int status) +{ + return; +} diff --git a/board/scb9328/u-boot.lds b/board/scb9328/u-boot.lds new file mode 100644 index 0000000000..5076303c7e --- /dev/null +++ b/board/scb9328/u-boot.lds @@ -0,0 +1,56 @@ +/* + * (C) Copyright 2000-2004 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + * + */ + +OUTPUT_FORMAT("elf32-littlearm", "elf32-littlearm", "elf32-littlearm") +OUTPUT_ARCH(arm) +ENTRY(_start) +SECTIONS +{ + . = 0x00000000; + + . = ALIGN(4); + .text : + { + cpu/arm920t/start.o (.text) + *(.text) + } + + . = ALIGN(4); + .rodata : { *(.rodata) } + + . = ALIGN(4); + .data : { *(.data) } + + . = ALIGN(4); + .got : { *(.got) } + + __u_boot_cmd_start = .; + .u_boot_cmd : { *(.u_boot_cmd) } + __u_boot_cmd_end = .; + + . = ALIGN(4); + __bss_start = .; + .bss : { *(.bss) } + _end = .; +} diff --git a/board/total5200/total5200.c b/board/total5200/total5200.c index 4ec7b96c49..1a35187260 100644 --- a/board/total5200/total5200.c +++ b/board/total5200/total5200.c @@ -265,7 +265,7 @@ static const S1D_REGS init_regs [] = void video_get_info_str (int line_number, char *info) { if (line_number == 1) { -#if CONFIG_MGT5100 +#ifdef CONFIG_MGT5100 strcpy (info, " Total5100"); #elif CONFIG_TOTAL5200_REV==1 strcpy (info, " Total5200"); diff --git a/common/Makefile b/common/Makefile index 4a36673b44..943da5e475 100644 --- a/common/Makefile +++ b/common/Makefile @@ -45,7 +45,7 @@ COBJS = main.o ACEX1K.o altera.o bedbug.o \ env_nand.o env_dataflash.o env_flash.o env_eeprom.o env_nvram.o env_nowhere.o exports.o \ flash.o fpga.o \ hush.o kgdb.o lists.o lynxkdi.o memsize.o miiphybb.o miiphyutil.o \ - s_record.o soft_i2c.o soft_spi.o spartan2.o \ + s_record.o serial.o soft_i2c.o soft_spi.o spartan2.o \ usb.o usb_kbd.o usb_storage.o \ virtex2.o xilinx.o circbuf.o diff --git a/common/cmd_bmp.c b/common/cmd_bmp.c index c1d4c0b90a..3a971334bb 100644 --- a/common/cmd_bmp.c +++ b/common/cmd_bmp.c @@ -123,14 +123,15 @@ static int bmp_info(ulong addr) */ static int bmp_display(ulong addr, int x, int y) { -#ifdef CONFIG_LCD - extern int lcd_display_bitmap (ulong, int, int); +#if defined(CONFIG_LCD) + extern int lcd_display_bitmap (ulong, int, int); return (lcd_display_bitmap (addr, x, y)); -#endif -#ifdef CONFIG_VIDEO +#elif defined(CONFIG_VIDEO) extern int video_display_bitmap (ulong, int, int); return (video_display_bitmap (addr, x, y)); +#else +# error bmp_display() requires CONFIG_LCD or CONFIG_VIDEO #endif } diff --git a/common/cmd_nvedit.c b/common/cmd_nvedit.c index aaf6de902b..3510561428 100644 --- a/common/cmd_nvedit.c +++ b/common/cmd_nvedit.c @@ -43,6 +43,7 @@ #include #include #include +#include #include #include #if (CONFIG_COMMANDS & CFG_CMD_NET) @@ -216,6 +217,11 @@ int _do_setenv (int flag, int argc, char *argv[]) /* Try assigning specified device */ if (console_assign (console, argv[2]) < 0) return 1; + +#ifdef CONFIG_SERIAL_MULTI + if (serial_assign (argv[2]) < 0) + return 1; +#endif } /* diff --git a/common/devices.c b/common/devices.c index 7c859521a3..b37c99a69b 100644 --- a/common/devices.c +++ b/common/devices.c @@ -26,6 +26,7 @@ #include #include #include +#include #ifdef CONFIG_LOGBUFFER #include #endif @@ -194,6 +195,9 @@ int devices_init (void) drv_logbuff_init (); #endif drv_system_init (); +#ifdef CONFIG_SERIAL_MULTI + serial_devices_init (); +#endif #ifdef CONFIG_USB_TTY drv_usbtty_init (); #endif diff --git a/common/serial.c b/common/serial.c new file mode 100644 index 0000000000..f89bb0a7a2 --- /dev/null +++ b/common/serial.c @@ -0,0 +1,196 @@ +/* + * (C) Copyright 2004 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include +#include +#include + +#if defined(CONFIG_SERIAL_MULTI) + +static struct serial_device *serial_devices = NULL; +static struct serial_device *serial_current = NULL; + +#ifndef CONFIG_LWMON +struct serial_device * default_serial_console (void) +{ +#if defined(CONFIG_8xx_CONS_SMC1) || defined(CONFIG_8xx_CONS_SMC2) + return &serial_smc_device; +#elif defined(CONFIG_8xx_CONS_SCC1) || defined(CONFIG_8xx_CONS_SCC2) \ + || defined(CONFIG_8xx_CONS_SCC3) || defined(CONFIG_8xx_CONS_SCC4) + return &serial_scc_device; +#else +#error No default console +#endif +} +#endif + +static int serial_register(struct serial_device* dev) +{ + DECLARE_GLOBAL_DATA_PTR; + + dev->init += gd->reloc_off; + dev->setbrg += gd->reloc_off; + dev->getc += gd->reloc_off; + dev->tstc += gd->reloc_off; + dev->putc += gd->reloc_off; + dev->puts += gd->reloc_off; + + dev->next = serial_devices; + serial_devices = dev; + + return 0; +} + +void serial_initialize(void) +{ +#if defined(CONFIG_8xx_CONS_SMC1) || defined(CONFIG_8xx_CONS_SMC2) + serial_register(&serial_smc_device); +#endif +#if defined(CONFIG_8xx_CONS_SCC1) || defined(CONFIG_8xx_CONS_SCC2) \ + || defined(CONFIG_8xx_CONS_SCC3) || defined(CONFIG_8xx_CONS_SCC4) + serial_register(&serial_scc_device); +#endif + + serial_assign(default_serial_console()->name); +} + +void serial_devices_init(void) +{ + device_t dev; + struct serial_device *s = serial_devices; + + while (s) + { + memset (&dev, 0, sizeof (dev)); + + strcpy (dev.name, s->name); + dev.flags = DEV_FLAGS_OUTPUT | DEV_FLAGS_INPUT; + + dev.start = s->init; + dev.putc = s->putc; + dev.puts = s->puts; + dev.getc = s->getc; + dev.tstc = s->tstc; + + device_register (&dev); + + s = s->next; + } +} + +int serial_assign(char * name) +{ + struct serial_device *s; + + for (s = serial_devices; s; s = s->next) + { + if (strcmp(s->name, name) == 0) + { + serial_current = s; + return 0; + } + } + + return 1; +} + +void serial_reinit_all(void) +{ + struct serial_device *s; + + for (s = serial_devices; s; s = s->next) + { + s->init(); + } +} + +int serial_init(void) +{ + if (!serial_current) + { + struct serial_device *dev = default_serial_console(); + return dev->init(); + } + + return serial_current->init(); +} + +void serial_setbrg(void) +{ + if (!serial_current) + { + struct serial_device *dev = default_serial_console(); + dev->setbrg(); + return; + } + + serial_current->setbrg(); +} + +int serial_getc(void) +{ + if (!serial_current) + { + struct serial_device *dev = default_serial_console(); + return dev->getc(); + } + + return serial_current->getc(); +} + +int serial_tstc(void) +{ + if (!serial_current) + { + struct serial_device *dev = default_serial_console(); + return dev->tstc(); + } + + return serial_current->tstc(); +} + +void serial_putc(const char c) +{ + if (!serial_current) + { + struct serial_device *dev = default_serial_console(); + dev->putc(c); + return; + } + + serial_current->putc(c); +} + +void serial_puts(const char *s) +{ + if (!serial_current) + { + struct serial_device *dev = default_serial_console(); + dev->puts(s); + return; + } + + serial_current->puts(s); +} + +#endif /* CONFIG_SERIAL_MULTI */ diff --git a/cpu/arm720t/cpu.c b/cpu/arm720t/cpu.c index 58eab4e550..ef3fbf35d1 100644 --- a/cpu/arm720t/cpu.c +++ b/cpu/arm720t/cpu.c @@ -41,8 +41,6 @@ int cpu_init (void) * setup up stacks if necessary */ #ifdef CONFIG_USE_IRQ - DECLARE_GLOBAL_DATA_PTR; - IRQ_STACK_START = _armboot_start - CFG_MALLOC_LEN - CFG_GBL_DATA_SIZE - 4; FIQ_STACK_START = IRQ_STACK_START - CONFIG_STACKSIZE_IRQ; #endif diff --git a/cpu/arm920t/Makefile b/cpu/arm920t/Makefile index 605adf301f..68a33d6559 100644 --- a/cpu/arm920t/Makefile +++ b/cpu/arm920t/Makefile @@ -26,7 +26,11 @@ include $(TOPDIR)/config.mk LIB = lib$(CPU).a START = start.o -OBJS = serial.o interrupts.o cpu.o speed.o usb_ohci.o +OBJS = cpu.o \ + imx_generic.o imx_interrupts.o imx_speed.o \ + interrupts.o \ + s3c24x0_interrupts.o s3c24x0_serial.o s3c24x0_speed.o \ + usb_ohci.o all: .depend $(START) $(LIB) diff --git a/cpu/arm920t/imx_generic.c b/cpu/arm920t/imx_generic.c new file mode 100644 index 0000000000..aa7c8c159d --- /dev/null +++ b/cpu/arm920t/imx_generic.c @@ -0,0 +1,90 @@ +/* + * arch/arm/mach-imx/generic.c + * + * author: Sascha Hauer + * Created: april 20th, 2004 + * Copyright: Synertronixx GmbH + * + * Common code for i.MX machines + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + * + */ + +#include + +#ifdef CONFIG_IMX + +#include + +void imx_gpio_mode(int gpio_mode) +{ + unsigned int pin = gpio_mode & GPIO_PIN_MASK; + unsigned int port = (gpio_mode & GPIO_PORT_MASK) >> 5; + unsigned int ocr = (gpio_mode & GPIO_OCR_MASK) >> 10; + unsigned int tmp; + + /* Pullup enable */ + if(gpio_mode & GPIO_PUEN) + PUEN(port) |= (1< + * Marius Groeger + * + * (C) Copyright 2002 + * Sysgo Real-Time Solutions, GmbH + * Alex Zuepke + * + * (C) Copyright 2002 + * Gary Jennejohn, DENX Software Engineering, + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include +#if defined (CONFIG_IMX) + +#include +#include + +int interrupt_init (void) +{ + int i; + /* setup GP Timer 1 */ + TCTL1 = TCTL_SWR; + for ( i=0; i<100; i++) TCTL1 = 0; /* We have no udelay by now */ + TPRER1 = get_PERCLK1() / 1000000; /* 1 MHz */ + TCTL1 |= TCTL_FRR | (1<<1); /* Freerun Mode, PERCLK1 input */ + + reset_timer_masked(); + + return (0); +} + +/* + * timer without interrupts + */ + +void reset_timer (void) +{ + reset_timer_masked (); +} + +ulong get_timer (ulong base) +{ + return get_timer_masked (); +} + +void set_timer (ulong t) +{ + /* nop */ +} + +void reset_timer_masked (void) +{ + TCTL1 &= ~TCTL_TEN; + TCTL1 |= TCTL_TEN; /* Enable timer */ +} + +ulong get_timer_masked (void) +{ + return TCN1; +} + +void udelay_masked (unsigned long usec) +{ + ulong start = get_timer_masked(); + + while (get_timer_masked () - start < usec ) + /*NOP*/; +} + +void udelay (unsigned long usec) +{ + udelay_masked(usec); +} + +/* + * This function is derived from PowerPC code (read timebase as long long). + * On ARM it just returns the timer value. + */ +unsigned long long get_ticks(void) +{ + return get_timer(0); +} + +/* + * This function is derived from PowerPC code (timebase clock frequency). + * On ARM it returns the number of timer ticks per second. + */ +ulong get_tbclk (void) +{ + ulong tbclk; + + tbclk = CFG_HZ; + + return tbclk; +} + +#endif /* defined (CONFIG_IMX) */ diff --git a/cpu/arm920t/imx_speed.c b/cpu/arm920t/imx_speed.c new file mode 100644 index 0000000000..1e296987d6 --- /dev/null +++ b/cpu/arm920t/imx_speed.c @@ -0,0 +1,102 @@ +/* + * + * (c) 2004 Sascha Hauer + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + + +#include +#if defined (CONFIG_IMX) + +#include + +/* ------------------------------------------------------------------------- */ +/* NOTE: This describes the proper use of this file. + * + * CONFIG_SYS_CLK_FREQ should be defined as the input frequency of the PLL. + * SH FIXME: 16780000 in our case + * get_FCLK(), get_HCLK(), get_PCLK() and get_UCLK() return the clock of + * the specified bus in HZ. + */ +/* ------------------------------------------------------------------------- */ + +ulong get_systemPLLCLK(void) +{ + /* FIXME: We assume System_SEL = 0 here */ + u32 spctl0 = SPCTL0; + u32 mfi = (spctl0 >> 10) & 0xf; + u32 mfn = spctl0 & 0x3f; + u32 mfd = (spctl0 >> 16) & 0x3f; + u32 pd = (spctl0 >> 26) & 0xf; + + mfi = mfi<=5 ? 5 : mfi; + + return (2*(CONFIG_SYSPLL_CLK_FREQ>>10)*( (mfi<<10) + (mfn<<10)/(mfd+1)))/(pd+1); +} + +ulong get_mcuPLLCLK(void) +{ + /* FIXME: We assume System_SEL = 0 here */ + u32 mpctl0 = MPCTL0; + u32 mfi = (mpctl0 >> 10) & 0xf; + u32 mfn = mpctl0 & 0x3f; + u32 mfd = (mpctl0 >> 16) & 0x3f; + u32 pd = (mpctl0 >> 26) & 0xf; + + mfi = mfi<=5 ? 5 : mfi; + + return (2*(CONFIG_SYS_CLK_FREQ>>10)*( (mfi<<10) + (mfn<<10)/(mfd+1)))/(pd+1); +} + +ulong get_FCLK(void) +{ + return (( CSCR>>15)&1) ? get_mcuPLLCLK()>>1 : get_mcuPLLCLK(); +} + +/* return HCLK frequency */ +ulong get_HCLK(void) +{ + u32 bclkdiv = (( CSCR >> 10 ) & 0xf) + 1; + printf("bclkdiv: %d\n", bclkdiv); + return get_systemPLLCLK() / bclkdiv; +} + +/* return BCLK frequency */ +ulong get_BCLK(void) +{ + return get_HCLK(); +} + +ulong get_PERCLK1(void) +{ + return get_systemPLLCLK() / (((PCDR) & 0xf)+1); +} + +ulong get_PERCLK2(void) +{ + return get_systemPLLCLK() / (((PCDR>>4) & 0xf)+1); +} + +ulong get_PERCLK3(void) +{ + return get_systemPLLCLK() / (((PCDR>>16) & 0x7f)+1); +} + +#endif /* defined (CONFIG_IMX) */ diff --git a/cpu/arm920t/interrupts.c b/cpu/arm920t/interrupts.c index 521c4f479d..ea58f154d4 100644 --- a/cpu/arm920t/interrupts.c +++ b/cpu/arm920t/interrupts.c @@ -30,25 +30,11 @@ */ #include -#include -#if defined(CONFIG_S3C2400) -#include -#elif defined(CONFIG_S3C2410) -#include -#endif +#include #include extern void reset_cpu(ulong addr); -int timer_load_val = 0; - -/* macro to read the 16 bit timer */ -static inline ulong READ_TIMER(void) -{ - S3C24X0_TIMERS * const timers = S3C24X0_GetBase_TIMERS(); - - return (timers->TCNTO4 & 0xffff); -} #ifdef CONFIG_USE_IRQ /* enable IRQ interrupts */ @@ -182,130 +168,3 @@ void do_irq (struct pt_regs *pt_regs) show_regs (pt_regs); bad_mode (); } - -static ulong timestamp; -static ulong lastdec; - -int interrupt_init (void) -{ - S3C24X0_TIMERS * const timers = S3C24X0_GetBase_TIMERS(); - - /* use PWM Timer 4 because it has no output */ - /* prescaler for Timer 4 is 16 */ - timers->TCFG0 = 0x0f00; - if (timer_load_val == 0) - { - /* - * for 10 ms clock period @ PCLK with 4 bit divider = 1/2 - * (default) and prescaler = 16. Should be 10390 - * @33.25MHz and 15625 @ 50 MHz - */ - timer_load_val = get_PCLK()/(2 * 16 * 100); - } - /* load value for 10 ms timeout */ - lastdec = timers->TCNTB4 = timer_load_val; - /* auto load, manual update of Timer 4 */ - timers->TCON = (timers->TCON & ~0x0700000) | 0x600000; - /* auto load, start Timer 4 */ - timers->TCON = (timers->TCON & ~0x0700000) | 0x500000; - timestamp = 0; - - return (0); -} - -/* - * timer without interrupts - */ - -void reset_timer (void) -{ - reset_timer_masked (); -} - -ulong get_timer (ulong base) -{ - return get_timer_masked () - base; -} - -void set_timer (ulong t) -{ - timestamp = t; -} - -void udelay (unsigned long usec) -{ - ulong tmo; - ulong start = get_timer(0); - - tmo = usec / 1000; - tmo *= (timer_load_val * 100); - tmo /= 1000; - - while ((ulong)(get_timer_masked () - start) < tmo) - /*NOP*/; -} - -void reset_timer_masked (void) -{ - /* reset time */ - lastdec = READ_TIMER(); - timestamp = 0; -} - -ulong get_timer_masked (void) -{ - ulong now = READ_TIMER(); - - if (lastdec >= now) { - /* normal mode */ - timestamp += lastdec - now; - } else { - /* we have an overflow ... */ - timestamp += lastdec + timer_load_val - now; - } - lastdec = now; - - return timestamp; -} - -void udelay_masked (unsigned long usec) -{ - ulong tmo; - - tmo = usec / 1000; - tmo *= (timer_load_val * 100); - tmo /= 1000; - - reset_timer_masked (); - - while (get_timer_masked () < tmo) - /*NOP*/; -} - -/* - * This function is derived from PowerPC code (read timebase as long long). - * On ARM it just returns the timer value. - */ -unsigned long long get_ticks(void) -{ - return get_timer(0); -} - -/* - * This function is derived from PowerPC code (timebase clock frequency). - * On ARM it returns the number of timer ticks per second. - */ -ulong get_tbclk (void) -{ - ulong tbclk; - -#if defined(CONFIG_SMDK2400) || defined(CONFIG_TRAB) - tbclk = timer_load_val * 100; -#elif defined(CONFIG_SMDK2410) || defined(CONFIG_VCMA9) - tbclk = CFG_HZ; -#else -# error "tbclk not configured" -#endif - - return tbclk; -} diff --git a/cpu/arm920t/s3c24x0_interrupts.c b/cpu/arm920t/s3c24x0_interrupts.c new file mode 100644 index 0000000000..92298b09f0 --- /dev/null +++ b/cpu/arm920t/s3c24x0_interrupts.c @@ -0,0 +1,180 @@ +/* + * (C) Copyright 2002 + * Sysgo Real-Time Solutions, GmbH + * Marius Groeger + * + * (C) Copyright 2002 + * Sysgo Real-Time Solutions, GmbH + * Alex Zuepke + * + * (C) Copyright 2002 + * Gary Jennejohn, DENX Software Engineering, + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include +#if defined(CONFIG_S3C2400) || defined (CONFIG_S3C2410) || defined (CONFIG_TRAB) + +#include +#if defined(CONFIG_S3C2400) +#include +#elif defined(CONFIG_S3C2410) +#include +#endif + +extern void reset_cpu(ulong addr); +int timer_load_val = 0; + +/* macro to read the 16 bit timer */ +static inline ulong READ_TIMER(void) +{ + S3C24X0_TIMERS * const timers = S3C24X0_GetBase_TIMERS(); + + return (timers->TCNTO4 & 0xffff); +} + +static ulong timestamp; +static ulong lastdec; + +int interrupt_init (void) +{ + S3C24X0_TIMERS * const timers = S3C24X0_GetBase_TIMERS(); + + /* use PWM Timer 4 because it has no output */ + /* prescaler for Timer 4 is 16 */ + timers->TCFG0 = 0x0f00; + if (timer_load_val == 0) + { + /* + * for 10 ms clock period @ PCLK with 4 bit divider = 1/2 + * (default) and prescaler = 16. Should be 10390 + * @33.25MHz and 15625 @ 50 MHz + */ + timer_load_val = get_PCLK()/(2 * 16 * 100); + } + /* load value for 10 ms timeout */ + lastdec = timers->TCNTB4 = timer_load_val; + /* auto load, manual update of Timer 4 */ + timers->TCON = (timers->TCON & ~0x0700000) | 0x600000; + /* auto load, start Timer 4 */ + timers->TCON = (timers->TCON & ~0x0700000) | 0x500000; + timestamp = 0; + + return (0); +} + +/* + * timer without interrupts + */ + +void reset_timer (void) +{ + reset_timer_masked (); +} + +ulong get_timer (ulong base) +{ + return get_timer_masked () - base; +} + +void set_timer (ulong t) +{ + timestamp = t; +} + +void udelay (unsigned long usec) +{ + ulong tmo; + ulong start = get_timer(0); + + tmo = usec / 1000; + tmo *= (timer_load_val * 100); + tmo /= 1000; + + while ((ulong)(get_timer_masked () - start) < tmo) + /*NOP*/; +} + +void reset_timer_masked (void) +{ + /* reset time */ + lastdec = READ_TIMER(); + timestamp = 0; +} + +ulong get_timer_masked (void) +{ + ulong now = READ_TIMER(); + + if (lastdec >= now) { + /* normal mode */ + timestamp += lastdec - now; + } else { + /* we have an overflow ... */ + timestamp += lastdec + timer_load_val - now; + } + lastdec = now; + + return timestamp; +} + +void udelay_masked (unsigned long usec) +{ + ulong tmo; + + tmo = usec / 1000; + tmo *= (timer_load_val * 100); + tmo /= 1000; + + reset_timer_masked (); + + while (get_timer_masked () < tmo) + /*NOP*/; +} + +/* + * This function is derived from PowerPC code (read timebase as long long). + * On ARM it just returns the timer value. + */ +unsigned long long get_ticks(void) +{ + return get_timer(0); +} + +/* + * This function is derived from PowerPC code (timebase clock frequency). + * On ARM it returns the number of timer ticks per second. + */ +ulong get_tbclk (void) +{ + ulong tbclk; + +#if defined(CONFIG_SMDK2400) || defined(CONFIG_TRAB) + tbclk = timer_load_val * 100; +#elif defined(CONFIG_SMDK2410) || defined(CONFIG_VCMA9) + tbclk = CFG_HZ; +#else +# error "tbclk not configured" +#endif + + return tbclk; +} + +#endif /* defined(CONFIG_S3C2400) || defined (CONFIG_S3C2410) || defined (CONFIG_TRAB) */ diff --git a/cpu/arm920t/serial.c b/cpu/arm920t/s3c24x0_serial.c similarity index 78% rename from cpu/arm920t/serial.c rename to cpu/arm920t/s3c24x0_serial.c index 1749e820a1..83274432e4 100644 --- a/cpu/arm920t/serial.c +++ b/cpu/arm920t/s3c24x0_serial.c @@ -1,24 +1,26 @@ - /* - * (C) Copyright 2002 - * Gary Jennejohn, DENX Software Engineering, - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License +/* + * (C) Copyright 2002 + * Gary Jennejohn, DENX Software Engineering, + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License * along with this program; if not, write to the Free Software * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA * */ #include +#if defined(CONFIG_S3C2400) || defined (CONFIG_S3C2410) || defined (CONFIG_TRAB) + #if defined(CONFIG_S3C2400) || defined(CONFIG_TRAB) #include #elif defined(CONFIG_S3C2410) @@ -176,3 +178,5 @@ serial_puts (const char *s) serial_putc (*s++); } } + +#endif /* defined(CONFIG_S3C2400) || defined (CONFIG_S3C2410) || defined (CONFIG_TRAB) */ diff --git a/cpu/arm920t/speed.c b/cpu/arm920t/s3c24x0_speed.c similarity index 93% rename from cpu/arm920t/speed.c rename to cpu/arm920t/s3c24x0_speed.c index 1f435436b0..e0dca62563 100644 --- a/cpu/arm920t/speed.c +++ b/cpu/arm920t/s3c24x0_speed.c @@ -1,5 +1,5 @@ /* - * (C) Copyright 2001-2002 + * (C) Copyright 2001-2004 * Wolfgang Denk, DENX Software Engineering, wd@denx.de. * * (C) Copyright 2002 @@ -30,6 +30,8 @@ */ #include +#if defined(CONFIG_S3C2400) || defined (CONFIG_S3C2410) || defined (CONFIG_TRAB) + #if defined(CONFIG_S3C2400) #include #elif defined(CONFIG_S3C2410) @@ -95,3 +97,5 @@ ulong get_UCLK(void) { return(get_PLLCLK(UPLL)); } + +#endif /* defined(CONFIG_S3C2400) || defined (CONFIG_S3C2410) || defined (CONFIG_TRAB) */ diff --git a/cpu/arm920t/start.S b/cpu/arm920t/start.S index 0e372d0e4c..78c470d7b6 100644 --- a/cpu/arm920t/start.S +++ b/cpu/arm920t/start.S @@ -118,20 +118,17 @@ reset: /* turn off the watchdog */ #if defined(CONFIG_S3C2400) -#define pWTCON 0x15300000 -/* Interupt-Controller base addresses */ -#define INTMSK 0x14400008 -/* clock divisor register */ -#define CLKDIVN 0x14800014 +# define pWTCON 0x15300000 +# define INTMSK 0x14400008 /* Interupt-Controller base addresses */ +# define CLKDIVN 0x14800014 /* clock divisor register */ #elif defined(CONFIG_S3C2410) -#define pWTCON 0x53000000 -/* Interupt-Controller base addresses */ -#define INTMSK 0x4A000008 -#define INTSUBMSK 0x4A00001C -/* clock divisor register */ -#define CLKDIVN 0x4C000014 +# define pWTCON 0x53000000 +# define INTMSK 0x4A000008 /* Interupt-Controller base addresses */ +# define INTSUBMSK 0x4A00001C +# define CLKDIVN 0x4C000014 /* clock divisor register */ #endif +#if defined(CONFIG_S3C2400) || defined(CONFIG_S3C2410) ldr r0, =pWTCON mov r1, #0x0 str r1, [r0] @@ -142,17 +139,18 @@ reset: mov r1, #0xffffffff ldr r0, =INTMSK str r1, [r0] -#if defined(CONFIG_S3C2410) +# if defined(CONFIG_S3C2410) ldr r1, =0x3ff ldr r0, =INTSUBMSK str r1, [r0] -#endif +# endif /* FCLK:HCLK:PCLK = 1:2:4 */ /* default FCLK is 120 MHz ! */ ldr r0, =CLKDIVN mov r1, #3 str r1, [r0] +#endif /* CONFIG_S3C2400 || CONFIG_S3C2410 */ /* * we do sys-critical inits only at reboot, diff --git a/cpu/mc9328/cpu.c b/cpu/mc9328/cpu.c deleted file mode 100644 index 2a2b578017..0000000000 --- a/cpu/mc9328/cpu.c +++ /dev/null @@ -1,183 +0,0 @@ -/* - * (C) Copyright 2002 - * Sysgo Real-Time Solutions, GmbH - * Marius Groeger - * - * (C) Copyright 2002 - * Gary Jennejohn, DENX Software Engineering, - * - * See file CREDITS for list of people who contributed to this - * project. - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation; either version 2 of - * the License, or (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, - * MA 02111-1307 USA - */ - -/* - * CPU specific code - */ - -#include -#include -#include - -/* read co-processor 15, register #1 (control register) */ -static unsigned long read_p15_c1 (void) -{ - unsigned long value; - - __asm__ __volatile__( - "mrc p15, 0, %0, c1, c0, 0 @ read control reg\n" - : "=r" (value) - : - : "memory"); - -#ifdef MMU_DEBUG - printf ("p15/c1 is = %08lx\n", value); -#endif - return value; -} - -/* write to co-processor 15, register #1 (control register) */ -static void write_p15_c1 (unsigned long value) -{ -#ifdef MMU_DEBUG - printf ("write %08lx to p15/c1\n", value); -#endif - __asm__ __volatile__( - "mcr p15, 0, %0, c1, c0, 0 @ write it back\n" - : - : "r" (value) - : "memory"); - - read_p15_c1 (); -} - -static void cp_delay (void) -{ - volatile int i; - - /* copro seems to need some delay between reading and writing */ - for (i = 0; i < 100; i++); -} - -/* See also ARM Ref. Man. */ -#define C1_MMU (1<<0) /* mmu off/on */ -#define C1_ALIGN (1<<1) /* alignment faults off/on */ -#define C1_DC (1<<2) /* dcache off/on */ -#define C1_BIG_ENDIAN (1<<7) /* big endian off/on */ -#define C1_SYS_PROT (1<<8) /* system protection */ -#define C1_ROM_PROT (1<<9) /* ROM protection */ -#define C1_IC (1<<12) /* icache off/on */ -#define C1_HIGH_VECTORS (1<<13) /* location of vectors: low/high addresses */ -#define RESERVED_1 (0xf << 3) /* must be 111b for R/W */ - -int cpu_init (void) -{ - /* - * setup up stacks if necessary - */ -#ifdef CONFIG_USE_IRQ - DECLARE_GLOBAL_DATA_PTR; - - IRQ_STACK_START = _armboot_start - CFG_MALLOC_LEN - CFG_GBL_DATA_SIZE - 4; - FIQ_STACK_START = IRQ_STACK_START - CONFIG_STACKSIZE_IRQ; -#endif - return 0; -} - -int cleanup_before_linux (void) -{ - /* - * this function is called just before we call linux - * it prepares the processor for linux - * - * we turn off caches etc ... - */ - - unsigned long i; - - disable_interrupts (); - - /* turn off I/D-cache */ - asm ("mrc p15, 0, %0, c1, c0, 0":"=r" (i)); - i &= ~(C1_DC | C1_IC); - asm ("mcr p15, 0, %0, c1, c0, 0": :"r" (i)); - - /* flush I/D-cache */ - i = 0; - asm ("mcr p15, 0, %0, c7, c7, 0": :"r" (i)); - return (0); -} - -int do_reset (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]) -{ - extern void reset_cpu (ulong addr); - - disable_interrupts (); - reset_cpu (0); - /*NOTREACHED*/ - return (0); -} - -void icache_enable (void) -{ - ulong reg; - - reg = read_p15_c1 (); - cp_delay (); - write_p15_c1 (reg | C1_IC); -} - -void icache_disable (void) -{ - ulong reg; - - reg = read_p15_c1 (); - cp_delay (); - write_p15_c1 (reg & ~C1_IC); -} - -int icache_status (void) -{ - return (read_p15_c1 () & C1_IC) != 0; -} - -#ifdef USE_920T_MMU -/* It makes no sense to use the dcache if the MMU is not enabled */ -void dcache_enable (void) -{ - ulong reg; - - reg = read_p15_c1 (); - cp_delay (); - write_p15_c1 (reg | C1_DC); -} - -void dcache_disable (void) -{ - ulong reg; - - reg = read_p15_c1 (); - cp_delay (); - reg &= ~C1_DC; - write_p15_c1 (reg); -} - -int dcache_status (void) -{ - return (read_p15_c1 () & C1_DC) != 0; -} -#endif diff --git a/cpu/mc9328/interrupts.c b/cpu/mc9328/interrupts.c deleted file mode 100644 index 2407db609f..0000000000 --- a/cpu/mc9328/interrupts.c +++ /dev/null @@ -1,249 +0,0 @@ -/* - * (C) Copyright 2002 - * Sysgo Real-Time Solutions, GmbH - * Marius Groeger - * - * (C) Copyright 2002 - * Sysgo Real-Time Solutions, GmbH - * Alex Zuepke - * - * (C) Copyright 2002 - * Gary Jennejohn, DENX Software Engineering, - * - * See file CREDITS for list of people who contributed to this - * project. - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation; either version 2 of - * the License, or (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, - * MA 02111-1307 USA - */ - -#include -#include -#include - -#include - -extern void reset_cpu(ulong addr); -int timer_load_val = 0; - -#ifdef CONFIG_USE_IRQ -/* enable IRQ interrupts */ -void enable_interrupts (void) -{ - unsigned long temp; - __asm__ __volatile__("mrs %0, cpsr\n" - "bic %0, %0, #0x80\n" - "msr cpsr_c, %0" - : "=r" (temp) - : - : "memory"); -} - - -/* - * disable IRQ/FIQ interrupts - * returns true if interrupts had been enabled before we disabled them - */ -int disable_interrupts (void) -{ - unsigned long old,temp; - __asm__ __volatile__("mrs %0, cpsr\n" - "orr %1, %0, #0xc0\n" - "msr cpsr_c, %1" - : "=r" (old), "=r" (temp) - : - : "memory"); - return (old & 0x80) == 0; -} -#else -void enable_interrupts (void) -{ - return; -} -int disable_interrupts (void) -{ - return 0; -} -#endif - - -void bad_mode (void) -{ - panic ("Resetting CPU ...\n"); - reset_cpu (0); -} - -void show_regs (struct pt_regs *regs) -{ - unsigned long flags; - const char *processor_modes[] = { - "USER_26", "FIQ_26", "IRQ_26", "SVC_26", - "UK4_26", "UK5_26", "UK6_26", "UK7_26", - "UK8_26", "UK9_26", "UK10_26", "UK11_26", - "UK12_26", "UK13_26", "UK14_26", "UK15_26", - "USER_32", "FIQ_32", "IRQ_32", "SVC_32", - "UK4_32", "UK5_32", "UK6_32", "ABT_32", - "UK8_32", "UK9_32", "UK10_32", "UND_32", - "UK12_32", "UK13_32", "UK14_32", "SYS_32", - }; - - flags = condition_codes (regs); - - printf ("pc : [<%08lx>] lr : [<%08lx>]\n" - "sp : %08lx ip : %08lx fp : %08lx\n", - instruction_pointer (regs), - regs->ARM_lr, regs->ARM_sp, regs->ARM_ip, regs->ARM_fp); - printf ("r10: %08lx r9 : %08lx r8 : %08lx\n", - regs->ARM_r10, regs->ARM_r9, regs->ARM_r8); - printf ("r7 : %08lx r6 : %08lx r5 : %08lx r4 : %08lx\n", - regs->ARM_r7, regs->ARM_r6, regs->ARM_r5, regs->ARM_r4); - printf ("r3 : %08lx r2 : %08lx r1 : %08lx r0 : %08lx\n", - regs->ARM_r3, regs->ARM_r2, regs->ARM_r1, regs->ARM_r0); - printf ("Flags: %c%c%c%c", - flags & CC_N_BIT ? 'N' : 'n', - flags & CC_Z_BIT ? 'Z' : 'z', - flags & CC_C_BIT ? 'C' : 'c', flags & CC_V_BIT ? 'V' : 'v'); - printf (" IRQs %s FIQs %s Mode %s%s\n", - interrupts_enabled (regs) ? "on" : "off", - fast_interrupts_enabled (regs) ? "on" : "off", - processor_modes[processor_mode (regs)], - thumb_mode (regs) ? " (T)" : ""); -} - -void do_undefined_instruction (struct pt_regs *pt_regs) -{ - printf ("undefined instruction\n"); - show_regs (pt_regs); - bad_mode (); -} - -void do_software_interrupt (struct pt_regs *pt_regs) -{ - printf ("software interrupt\n"); - show_regs (pt_regs); - bad_mode (); -} - -void do_prefetch_abort (struct pt_regs *pt_regs) -{ - printf ("prefetch abort\n"); - show_regs (pt_regs); - bad_mode (); -} - -void do_data_abort (struct pt_regs *pt_regs) -{ - printf ("data abort\n"); - show_regs (pt_regs); - bad_mode (); -} - -void do_not_used (struct pt_regs *pt_regs) -{ - printf ("not used\n"); - show_regs (pt_regs); - bad_mode (); -} - -void do_fiq (struct pt_regs *pt_regs) -{ - printf ("fast interrupt request\n"); - show_regs (pt_regs); - bad_mode (); -} - -void do_irq (struct pt_regs *pt_regs) -{ - printf ("interrupt request\n"); - show_regs (pt_regs); - bad_mode (); -} - - -int interrupt_init (void) -{ - -/* we don't use interrupt */ - return(0); -} - -/* - * timer without interrupts - */ - -void reset_timer (void) -{ - reset_timer_masked (); -} - -ulong get_timer (ulong base) -{ - return get_timer_masked (); -} - -void set_timer (ulong t) -{ -/* Nop */ -} - -void udelay (unsigned long usec) -{ - udelay_masked (usec); -} - -void reset_timer_masked (void) -{ - u32 tmp; - MX1_TCTL1 = 0x09; - tmp = 0x1f; /* a little delay for timer to reset */ - MX1_TPRER1 = 0x1f; - MX1_TCTL1 = 0x19; -} - -ulong get_timer_masked (void) -{ - return MX1_TCN1; -} - -void udelay_masked (unsigned long usec) -{ - ulong tmo; - - tmo = usec / 1000; - tmo *= CFG_HZ; - tmo /= 1000; - - reset_timer_masked (); - - while (get_timer_masked () < tmo); -} - -/* - * This function is derived from PowerPC code (read timebase as long long). - * On ARM it just returns the timer value. - */ -unsigned long long get_ticks(void) -{ - return get_timer(0); -} - -/* - * This function is derived from PowerPC code (timebase clock frequency). - * On ARM it returns the number of timer ticks per second. - */ - -ulong get_tbclk (void) { - return CFG_HZ; -} diff --git a/cpu/mc9328/serial.c b/cpu/mc9328/serial.c deleted file mode 100644 index 8dcfb80274..0000000000 --- a/cpu/mc9328/serial.c +++ /dev/null @@ -1,133 +0,0 @@ -/* - * cpu/mc9328/serial.c - * - * (c) Copyright 2004 - * Techware Information Technology, Inc. - * http://www.techware.com.tw/ - * - * Ming-Len Wu - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation; either version 2 of - * the License, or (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, - * MA 02111-1307 USA - */ - -#include -#include - -#if defined(CONFIG_UART1) -/* GPIO PORT B */ - -#define reg_GIUS MX1_GIUS_C -#define reg_GPR MX1_GPR_B -#define GPIO_MASK 0xFFFFE1FF -#define UART_BASE 0x00206000 - -#elif defined (CONFIG_UART2) -/* GPIO PORT C */ - -#define reg_GIUS MX1_GIUS_C -#define reg_GPR MX1_GPR_C -#define GPIO_MASK 0x0FFFFFFF -#define UART_BASE 0x207000 - -#endif - -#define reg_URXD (*((volatile u32 *)(UART_BASE+0x00))) -#define reg_UTXD (*((volatile u32 *)(UART_BASE+0x40))) -#define reg_UCR1 (*((volatile u32 *)(UART_BASE+0x80))) -#define reg_UCR2 (*((volatile u32 *)(UART_BASE+0x84))) -#define reg_UCR3 (*((volatile u32 *)(UART_BASE+0x88))) -#define reg_UCR4 (*((volatile u32 *)(UART_BASE+0x8C))) -#define reg_UFCR (*((volatile u32 *)(UART_BASE+0x90))) -#define reg_USR1 (*((volatile u32 *)(UART_BASE+0x94))) -#define reg_USR2 (*((volatile u32 *)(UART_BASE+0x98))) -#define reg_UESC (*((volatile u32 *)(UART_BASE+0x9C))) -#define reg_UTIM (*((volatile u32 *)(UART_BASE+0xA0))) -#define reg_UBIR (*((volatile u32 *)(UART_BASE+0xA4))) -#define reg_UBMR (*((volatile u32 *)(UART_BASE+0xA8))) -#define reg_UBRC (*((volatile u32 *)(UART_BASE+0xAC))) - -#define TXFE_MASK 0x4000 /* Tx buffer empty */ -#define RDR_MASK 0x0001 /* receive data ready */ - -void serial_setbrg (void) { - - /* config I/O pins for UART */ - reg_GIUS &= GPIO_MASK; - reg_GPR &= GPIO_MASK; - - /* config UART */ - reg_UCR1 = 5; - reg_UCR2 = 0x4027; - reg_UCR4 = 1; - reg_UFCR = 0xA81; - - reg_UBIR = 0xF; - reg_UBMR = 0x8A; - reg_UBRC = 8; -} - -/* - * Initialise the serial port with the given baudrate. The settings - * are always 8 data bits, no parity, 1 stop bit, no start bits. - * - */ - -int serial_init (void) { - serial_setbrg (); - - return (0); -} - -/* - * Read a single byte from the serial port. Returns 1 on success, 0 - * otherwise. When the function is succesfull, the character read is - * written into its argument c. - */ -int serial_getc (void) { - - while (!(reg_USR2 & RDR_MASK)) ; /* wait until RDR bit set */ - - return (u8)reg_URXD; -} - -/* - * Output a single byte to the serial port. - */ -void serial_putc (const char c) { - - while (!(reg_USR2 & TXFE_MASK)); /* wait until TXFE bit set */ - - reg_UTXD = (u16) c; - - if (c == '\n') { /* carriage return ? append line-feed */ - while (!(reg_USR2 & TXFE_MASK)); /* wait until TXFE bit set */ - reg_UTXD = '\r'; - } - -} - -/* - * Test whether a character is in the RX buffer - */ -int serial_tstc (void) { - return reg_USR2 & RDR_MASK; -} - -void serial_puts (const char *s) { - while (*s) { - serial_putc (*s++); - } -} diff --git a/cpu/mc9328/start.S b/cpu/mc9328/start.S deleted file mode 100644 index edfce121b7..0000000000 --- a/cpu/mc9328/start.S +++ /dev/null @@ -1,388 +0,0 @@ -/* - * armboot - Startup Code for ARM920 CPU-core - * - * Copyright (c) 2001 Marius Gröger - * Copyright (c) 2002 Alex Züpke - * Copyright (c) 2002 Gary Jennejohn - * - * See file CREDITS for list of people who contributed to this - * project. - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation; either version 2 of - * the License, or (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, - * MA 02111-1307 USA - */ - - -#include -#include - - -/* - ************************************************************************* - * - * Jump vector table as in table 3.1 in [1] - * - ************************************************************************* - */ - - -.globl _start -_start: b reset - ldr pc, _undefined_instruction - ldr pc, _software_interrupt - ldr pc, _prefetch_abort - ldr pc, _data_abort - ldr pc, _not_used - ldr pc, _irq - ldr pc, _fiq - -_undefined_instruction: .word undefined_instruction -_software_interrupt: .word software_interrupt -_prefetch_abort: .word prefetch_abort -_data_abort: .word data_abort -_not_used: .word not_used -_irq: .word irq -_fiq: .word fiq - - .balignl 16,0xdeadbeef - - -/* - ************************************************************************* - * - * Startup Code (reset vector) - * - * do important init only if we don't start from memory! - * relocate armboot to ram - * setup stack - * jump to second stage - * - ************************************************************************* - */ - -_TEXT_BASE: - .word TEXT_BASE - -.globl _armboot_start -_armboot_start: - .word _start - -/* - * These are defined in the board-specific linker script. - */ -.globl _bss_start -_bss_start: - .word __bss_start - -.globl _bss_end -_bss_end: - .word _end - -#ifdef CONFIG_USE_IRQ -/* IRQ stack memory (calculated at run-time) */ -.globl IRQ_STACK_START -IRQ_STACK_START: - .word 0x0badc0de - -/* IRQ stack memory (calculated at run-time) */ -.globl FIQ_STACK_START -FIQ_STACK_START: - .word 0x0badc0de -#endif - - -/* - * the actual reset code - */ - -reset: - /* - * set the cpu to SVC32 mode - */ - mrs r0,cpsr - bic r0,r0,#0x1f - orr r0,r0,#0xd3 - msr cpsr,r0 - - /* - * we do sys-critical inits only at reboot, - * not when booting from ram! - */ -#ifdef CONFIG_INIT_CRITICAL - bl cpu_init_crit -#endif - -relocate: /* relocate U-Boot to RAM */ - adr r0, _start /* r0 <- current position of code */ - ldr r1, _TEXT_BASE /* test if we run from flash or RAM */ - cmp r0, r1 /* don't reloc during debug */ - beq stack_setup - - ldr r2, _armboot_start - ldr r3, _bss_start - sub r2, r3, r2 /* r2 <- size of armboot */ - add r2, r0, r2 /* r2 <- source end address */ - -copy_loop: - ldmia r0!, {r3-r10} /* copy from source address [r0] */ - stmia r1!, {r3-r10} /* copy to target address [r1] */ - cmp r0, r2 /* until source end addreee [r2] */ - ble copy_loop - - /* Set up the stack */ -stack_setup: - ldr r0, _TEXT_BASE /* upper 128 KiB: relocated uboot */ - sub r0, r0, #CFG_MALLOC_LEN /* malloc area */ - sub r0, r0, #CFG_GBL_DATA_SIZE /* bdinfo */ -#ifdef CONFIG_USE_IRQ - sub r0, r0, #(CONFIG_STACKSIZE_IRQ+CONFIG_STACKSIZE_FIQ) -#endif - sub sp, r0, #12 /* leave 3 words for abort-stack */ - -clear_bss: - ldr r0, _bss_start /* find start of bss segment */ - ldr r1, _bss_end /* stop here */ - mov r2, #0x00000000 /* clear */ - -clbss_l:str r2, [r0] /* clear loop... */ - add r0, r0, #4 - cmp r0, r1 - bne clbss_l - - ldr pc, _start_armboot - -_start_armboot: .word start_armboot - - -/* - ************************************************************************* - * - * CPU_init_critical registers - * - * setup important registers - * setup memory timing - * - ************************************************************************* - */ - - -cpu_init_crit: - /* - * flush v4 I/D caches - */ - mov r0, #0 - mcr p15, 0, r0, c7, c7, 0 /* flush v3/v4 cache */ - mcr p15, 0, r0, c8, c7, 0 /* flush v4 TLB */ - - /* - * disable MMU stuff and caches - */ - mrc p15, 0, r0, c1, c0, 0 - bic r0, r0, #0x00002300 @ clear bits 13, 9:8 (--V- --RS) - bic r0, r0, #0x00000087 @ clear bits 7, 2:0 (B--- -CAM) - orr r0, r0, #0x00000002 @ set bit 2 (A) Align - orr r0, r0, #0x00001000 @ set bit 12 (I) I-Cache - mcr p15, 0, r0, c1, c0, 0 - - - /* - * before relocating, we have to setup RAM timing - * because memory timing is board-dependend, you will - * find a memsetup.S in your board directory. - */ - mov ip, lr - bl memsetup - mov lr, ip - - mov pc, lr - - -/* - ************************************************************************* - * - * Interrupt handling - * - ************************************************************************* - */ - -@ -@ IRQ stack frame. -@ -#define S_FRAME_SIZE 72 - -#define S_OLD_R0 68 -#define S_PSR 64 -#define S_PC 60 -#define S_LR 56 -#define S_SP 52 - -#define S_IP 48 -#define S_FP 44 -#define S_R10 40 -#define S_R9 36 -#define S_R8 32 -#define S_R7 28 -#define S_R6 24 -#define S_R5 20 -#define S_R4 16 -#define S_R3 12 -#define S_R2 8 -#define S_R1 4 -#define S_R0 0 - -#define MODE_SVC 0x13 -#define I_BIT 0x80 - -/* - * use bad_save_user_regs for abort/prefetch/undef/swi ... - * use irq_save_user_regs / irq_restore_user_regs for IRQ/FIQ handling - */ - - .macro bad_save_user_regs - sub sp, sp, #S_FRAME_SIZE - stmia sp, {r0 - r12} @ Calling r0-r12 - ldr r2, _armboot_start - sub r2, r2, #(CONFIG_STACKSIZE+CFG_MALLOC_LEN) - sub r2, r2, #(CFG_GBL_DATA_SIZE+8) @ set base 2 words into abort stack - ldmia r2, {r2 - r3} @ get pc, cpsr - add r0, sp, #S_FRAME_SIZE @ restore sp_SVC - - add r5, sp, #S_SP - mov r1, lr - stmia r5, {r0 - r3} @ save sp_SVC, lr_SVC, pc, cpsr - mov r0, sp - .endm - - .macro irq_save_user_regs - sub sp, sp, #S_FRAME_SIZE - stmia sp, {r0 - r12} @ Calling r0-r12 - add r8, sp, #S_PC - stmdb r8, {sp, lr}^ @ Calling SP, LR - str lr, [r8, #0] @ Save calling PC - mrs r6, spsr - str r6, [r8, #4] @ Save CPSR - str r0, [r8, #8] @ Save OLD_R0 - mov r0, sp - .endm - - .macro irq_restore_user_regs - ldmia sp, {r0 - lr}^ @ Calling r0 - lr - mov r0, r0 - ldr lr, [sp, #S_PC] @ Get PC - add sp, sp, #S_FRAME_SIZE - subs pc, lr, #4 @ return & move spsr_svc into cpsr - .endm - - .macro get_bad_stack - ldr r13, _armboot_start @ setup our mode stack - sub r13, r13, #(CONFIG_STACKSIZE+CFG_MALLOC_LEN) - sub r13, r13, #(CFG_GBL_DATA_SIZE+8) @ reserved a couple spots in abort stack - - str lr, [r13] @ save caller lr / spsr - mrs lr, spsr - str lr, [r13, #4] - - mov r13, #MODE_SVC @ prepare SVC-Mode - @ msr spsr_c, r13 - msr spsr, r13 - mov lr, pc - movs pc, lr - .endm - - .macro get_irq_stack @ setup IRQ stack - ldr sp, IRQ_STACK_START - .endm - - .macro get_fiq_stack @ setup FIQ stack - ldr sp, FIQ_STACK_START - .endm - -/* - * exception handlers - */ - .align 5 -undefined_instruction: - get_bad_stack - bad_save_user_regs - bl do_undefined_instruction - - .align 5 -software_interrupt: - get_bad_stack - bad_save_user_regs - bl do_software_interrupt - - .align 5 -prefetch_abort: - get_bad_stack - bad_save_user_regs - bl do_prefetch_abort - - .align 5 -data_abort: - get_bad_stack - bad_save_user_regs - bl do_data_abort - - .align 5 -not_used: - get_bad_stack - bad_save_user_regs - bl do_not_used - -#ifdef CONFIG_USE_IRQ - - .align 5 -irq: - get_irq_stack - irq_save_user_regs - bl do_irq - irq_restore_user_regs - - .align 5 -fiq: - get_fiq_stack - /* someone ought to write a more effiction fiq_save_user_regs */ - irq_save_user_regs - bl do_fiq - irq_restore_user_regs - -#else - - .align 5 -irq: - get_bad_stack - bad_save_user_regs - bl do_irq - - .align 5 -fiq: - get_bad_stack - bad_save_user_regs - bl do_fiq - -#endif - - .align 5 -.globl reset_cpu -reset_cpu: - mov ip, #0 - mcr p15, 0, ip, c7, c7, 0 @ invalidate cache - mcr p15, 0, ip, c8, c7, 0 @ flush TLB (v4) - mrc p15, 0, ip, c1, c0, 0 @ get ctrl register - bic ip, ip, #0x000f @ ............wcam - bic ip, ip, #0x2100 @ ..v....s........ - mcr p15, 0, ip, c1, c0, 0 @ ctrl register - mov pc, r0 diff --git a/cpu/mpc824x/cpu_init.c b/cpu/mpc824x/cpu_init.c index 08f5c4ab13..d0c7a3bcab 100644 --- a/cpu/mpc824x/cpu_init.c +++ b/cpu/mpc824x/cpu_init.c @@ -108,7 +108,7 @@ cpu_init_f (void) CONFIG_READ_BYTE(PCMBCR,val); /* in order not to corrupt data which is being read over the PCI bus - * with the PPC as master, we need to reduce the number of PCMRBs to 1, + * with the PPC as slave, we need to reduce the number of PCMRBs to 1, * 4.11 in the processor user manual * */ @@ -117,6 +117,10 @@ cpu_init_f (void) #else CONFIG_WRITE_BYTE(PCMBCR,(val|0x80)); /* 2 PCMRBs */ CONFIG_WRITE_BYTE(PCMBCR,(val|0x40)); /* 3 PCMRBs */ + /* default, 4 PCMRBs are used, so don't change the + * register is this is _really_ what you want: data + * corruption with no performance gain + */ #endif #endif diff --git a/cpu/mpc85xx/speed.c b/cpu/mpc85xx/speed.c index d40cd8c486..787f7fadc9 100644 --- a/cpu/mpc85xx/speed.c +++ b/cpu/mpc85xx/speed.c @@ -33,7 +33,6 @@ void get_sys_info (sys_info_t * sysInfo) { - DECLARE_GLOBAL_DATA_PTR; volatile immap_t *immap = (immap_t *)CFG_IMMR; volatile ccsr_gur_t *gur = &immap->im_gur; uint plat_ratio,e500_ratio; diff --git a/cpu/mpc8xx/scc.c b/cpu/mpc8xx/scc.c index 78b2f9914d..6b9110f130 100644 --- a/cpu/mpc8xx/scc.c +++ b/cpu/mpc8xx/scc.c @@ -193,6 +193,10 @@ static int scc_init (struct eth_device *dev, bd_t * bis) volatile immap_t *immr = (immap_t *) CFG_IMMR; +#if defined(CONFIG_LWMON) + reset_phy(); +#endif + #ifdef CONFIG_FADS #if defined(CONFIG_MPC86xADS) || defined(CONFIG_MPC860T) /* The MPC86xADS/FADS860T don't use the MODEM_EN or DATA_VOICE signals. */ @@ -550,6 +554,8 @@ static void scc_halt (struct eth_device *dev) immr->im_cpm.cp_scc[SCC_ENET].scc_gsmrl &= ~(SCC_GSMRL_ENR | SCC_GSMRL_ENT); + + immr->im_ioport.iop_pcso &= ~(PC_ENET_CLSN | PC_ENET_RENA); } #if 0 diff --git a/cpu/mpc8xx/serial.c b/cpu/mpc8xx/serial.c index 71f3ae1f45..fa0405f198 100644 --- a/cpu/mpc8xx/serial.c +++ b/cpu/mpc8xx/serial.c @@ -24,49 +24,44 @@ #include #include #include +#include #include #if !defined(CONFIG_8xx_CONS_NONE) /* No Console at all */ #if defined(CONFIG_8xx_CONS_SMC1) /* Console on SMC1 */ #define SMC_INDEX 0 -#undef SCC_INDEX #define PROFF_SMC PROFF_SMC1 #define CPM_CR_CH_SMC CPM_CR_CH_SMC1 #elif defined(CONFIG_8xx_CONS_SMC2) /* Console on SMC2 */ #define SMC_INDEX 1 -#undef SCC_INDEX #define PROFF_SMC PROFF_SMC2 #define CPM_CR_CH_SMC CPM_CR_CH_SMC2 -#elif defined(CONFIG_8xx_CONS_SCC1) /* Console on SCC1 */ -#undef SMC_INDEX +#endif /* CONFIG_8xx_CONS_SMCx */ + +#if defined(CONFIG_8xx_CONS_SCC1) /* Console on SCC1 */ #define SCC_INDEX 0 #define PROFF_SCC PROFF_SCC1 #define CPM_CR_CH_SCC CPM_CR_CH_SCC1 #elif defined(CONFIG_8xx_CONS_SCC2) /* Console on SCC2 */ -#undef SMC_INDEX #define SCC_INDEX 1 #define PROFF_SCC PROFF_SCC2 #define CPM_CR_CH_SCC CPM_CR_CH_SCC2 #elif defined(CONFIG_8xx_CONS_SCC3) /* Console on SCC3 */ -#undef SMC_INDEX #define SCC_INDEX 2 #define PROFF_SCC PROFF_SCC3 #define CPM_CR_CH_SCC CPM_CR_CH_SCC3 #elif defined(CONFIG_8xx_CONS_SCC4) /* Console on SCC4 */ -#undef SMC_INDEX #define SCC_INDEX 3 #define PROFF_SCC PROFF_SCC4 #define CPM_CR_CH_SCC CPM_CR_CH_SCC4 -#else /* CONFIG_8xx_CONS_? */ -#error "console not correctly defined" -#endif +#endif /* CONFIG_8xx_CONS_SCCx */ static void serial_setdivisor(volatile cpm8xx_t *cp) { @@ -96,7 +91,23 @@ static void serial_setdivisor(volatile cpm8xx_t *cp) * as serial console interface. */ -int serial_init (void) +static void smc_setbrg (void) +{ + volatile immap_t *im = (immap_t *)CFG_IMMR; + volatile cpm8xx_t *cp = &(im->im_cpm); + + /* Set up the baud rate generator. + * See 8xx_io/commproc.c for details. + * + * Wire BRG1 to SMCx + */ + + cp->cp_simode = 0x00000000; + + serial_setdivisor(cp); +} + +static int smc_init (void) { volatile immap_t *im = (immap_t *)CFG_IMMR; volatile smc_t *sp; @@ -217,7 +228,7 @@ int serial_init (void) /* Set up the baud rate generator. */ - serial_setbrg (); + smc_setbrg (); /* Make the first buffer the only buffer. */ @@ -247,39 +258,8 @@ int serial_init (void) return (0); } -void -serial_setbrg (void) -{ - volatile immap_t *im = (immap_t *)CFG_IMMR; - volatile cpm8xx_t *cp = &(im->im_cpm); - - /* Set up the baud rate generator. - * See 8xx_io/commproc.c for details. - * - * Wire BRG1 to SMCx - */ - - cp->cp_simode = 0x00000000; - - serial_setdivisor(cp); -} - -#ifdef CONFIG_MODEM_SUPPORT -void disable_putc(void) -{ - DECLARE_GLOBAL_DATA_PTR; - gd->be_quiet = 1; -} - -void enable_putc(void) -{ - DECLARE_GLOBAL_DATA_PTR; - gd->be_quiet = 0; -} -#endif - -void -serial_putc(const char c) +static void +smc_putc(const char c) { volatile cbd_t *tbdf; volatile char *buf; @@ -295,7 +275,7 @@ serial_putc(const char c) #endif if (c == '\n') - serial_putc ('\r'); + smc_putc ('\r'); up = (smc_uart_t *)&cpmp->cp_dparam[PROFF_SMC]; @@ -317,8 +297,16 @@ serial_putc(const char c) } } -int -serial_getc(void) +static void +smc_puts (const char *s) +{ + while (*s) { + smc_putc (*s++); + } +} + +static int +smc_getc(void) { volatile cbd_t *rbdf; volatile unsigned char *buf; @@ -344,8 +332,8 @@ serial_getc(void) return(c); } -int -serial_tstc() +static int +smc_tstc(void) { volatile cbd_t *rbdf; volatile smc_uart_t *up; @@ -359,9 +347,41 @@ serial_tstc() return(!(rbdf->cbd_sc & BD_SC_EMPTY)); } -#else /* ! CONFIG_8xx_CONS_SMC1, CONFIG_8xx_CONS_SMC2 */ +struct serial_device serial_smc_device = +{ + "serial_smc", + "SMC", + smc_init, + smc_setbrg, + smc_getc, + smc_tstc, + smc_putc, + smc_puts, +}; + +#endif /* CONFIG_8xx_CONS_SMC1 || CONFIG_8xx_CONS_SMC2 */ + +#if defined(CONFIG_8xx_CONS_SCC1) || defined(CONFIG_8xx_CONS_SCC2) || \ + defined(CONFIG_8xx_CONS_SCC3) || defined(CONFIG_8xx_CONS_SCC4) + +static void +scc_setbrg (void) +{ + volatile immap_t *im = (immap_t *)CFG_IMMR; + volatile cpm8xx_t *cp = &(im->im_cpm); -int serial_init (void) + /* Set up the baud rate generator. + * See 8xx_io/commproc.c for details. + * + * Wire BRG1 to SCCx + */ + + cp->cp_sicr &= ~(0x000000FF << (8 * SCC_INDEX)); + + serial_setdivisor(cp); +} + +static int scc_init (void) { volatile immap_t *im = (immap_t *)CFG_IMMR; volatile scc_t *sp; @@ -426,7 +446,7 @@ int serial_init (void) #ifdef CFG_ALLOC_DPRAM dpaddr = dpram_alloc_align (sizeof(cbd_t)*2 + 2, 8) ; #else - dpaddr = CPM_SERIAL_BASE ; + dpaddr = CPM_SERIAL2_BASE ; #endif /* Enable SDMA. @@ -446,7 +466,7 @@ int serial_init (void) /* Set up the baud rate generator. */ - serial_setbrg (); + scc_setbrg (); /* Set up the uart parameters in the parameter ram. */ @@ -497,9 +517,11 @@ int serial_init (void) /* Set UART mode, clock divider 16 on Tx and Rx */ + sp->scc_gsmrl &= ~0xF; sp->scc_gsmrl |= (SCC_GSMRL_MODE_UART | SCC_GSMRL_TDCR_16 | SCC_GSMRL_RDCR_16); + sp->scc_psmr = 0; sp->scc_psmr |= SCU_PSMR_CL; /* Mask all interrupts and remove anything pending. @@ -521,25 +543,8 @@ int serial_init (void) return (0); } -void -serial_setbrg (void) -{ - volatile immap_t *im = (immap_t *)CFG_IMMR; - volatile cpm8xx_t *cp = &(im->im_cpm); - - /* Set up the baud rate generator. - * See 8xx_io/commproc.c for details. - * - * Wire BRG1 to SCCx - */ - - cp->cp_sicr &= ~(0x000000FF << (8 * SCC_INDEX)); - - serial_setdivisor(cp); -} - -void -serial_putc(const char c) +static void +scc_putc(const char c) { volatile cbd_t *tbdf; volatile char *buf; @@ -547,8 +552,15 @@ serial_putc(const char c) volatile immap_t *im = (immap_t *)CFG_IMMR; volatile cpm8xx_t *cpmp = &(im->im_cpm); +#ifdef CONFIG_MODEM_SUPPORT + DECLARE_GLOBAL_DATA_PTR; + + if (gd->be_quiet) + return; +#endif + if (c == '\n') - serial_putc ('\r'); + scc_putc ('\r'); up = (scc_uart_t *)&cpmp->cp_dparam[PROFF_SCC]; @@ -570,8 +582,16 @@ serial_putc(const char c) } } -int -serial_getc(void) +static void +scc_puts (const char *s) +{ + while (*s) { + scc_putc (*s++); + } +} + +static int +scc_getc(void) { volatile cbd_t *rbdf; volatile unsigned char *buf; @@ -597,8 +617,8 @@ serial_getc(void) return(c); } -int -serial_tstc() +static int +scc_tstc(void) { volatile cbd_t *rbdf; volatile scc_uart_t *up; @@ -612,36 +632,66 @@ serial_tstc() return(!(rbdf->cbd_sc & BD_SC_EMPTY)); } -#endif /* CONFIG_8xx_CONS_SMC1, CONFIG_8xx_CONS_SMC2 */ - +struct serial_device serial_scc_device = +{ + "serial_scc", + "SCC", + scc_init, + scc_setbrg, + scc_getc, + scc_tstc, + scc_putc, + scc_puts, +}; + +#endif /* CONFIG_8xx_CONS_SCCx */ -void -serial_puts (const char *s) +#ifdef CONFIG_MODEM_SUPPORT +void disable_putc(void) { - while (*s) { - serial_putc (*s++); - } + DECLARE_GLOBAL_DATA_PTR; + gd->be_quiet = 1; } +void enable_putc(void) +{ + DECLARE_GLOBAL_DATA_PTR; + gd->be_quiet = 0; +} +#endif #if (CONFIG_COMMANDS & CFG_CMD_KGDB) void kgdb_serial_init(void) { + int i = -1; + + if (strcmp(default_serial_console()->ctlr, "SMC") == 0) + { #if defined(CONFIG_8xx_CONS_SMC1) - serial_printf("[on SMC1] "); + i = 1; #elif defined(CONFIG_8xx_CONS_SMC2) - serial_printf("[on SMC2] "); -#elif defined(CONFIG_8xx_CONS_SCC1) - serial_printf("[on SCC1] "); + i = 2; +#endif + } + else if (strcmp(default_serial_console()->ctlr, "SMC") == 0) + { +#if defined(CONFIG_8xx_CONS_SCC1) + i = 1; #elif defined(CONFIG_8xx_CONS_SCC2) - serial_printf("[on SCC2] "); + i = 2; #elif defined(CONFIG_8xx_CONS_SCC3) - serial_printf("[on SCC3] "); + i = 3; #elif defined(CONFIG_8xx_CONS_SCC4) - serial_printf("[on SCC4] "); + i = 4; #endif + } + + if (i >= 0) + { + serial_printf("[on %s%d] ", default_serial_console()->ctlr, i); + } } void diff --git a/cpu/mpc8xx/spi.c b/cpu/mpc8xx/spi.c index 5d75207733..9213d101a7 100644 --- a/cpu/mpc8xx/spi.c +++ b/cpu/mpc8xx/spi.c @@ -39,7 +39,7 @@ #include #include #include -#include +#include #if (defined(CONFIG_SPI)) || (CONFIG_POST & CFG_POST_SPI) @@ -542,13 +542,13 @@ int spi_post_test (int flags) cp->cp_spmode &= ~SPMODE_LOOP; /* - * SCC2 Ethernet parameter RAM space overlaps + * SCC2 parameter RAM space overlaps * the SPI parameter RAM space. So we need to restore - * the SCC2 configuration if it is used by UART or Ethernet. + * the SCC2 configuration if it is used by UART. */ -#if defined(CONFIG_8xx_CONS_SCC2) - serial_init (); +#if !defined(CONFIG_8xx_CONS_NONE) + serial_reinit_all (); #endif if (res != 0) { diff --git a/doc/README.serial_multi b/doc/README.serial_multi new file mode 100644 index 0000000000..1d73376b2c --- /dev/null +++ b/doc/README.serial_multi @@ -0,0 +1,37 @@ +The support for multiple serial interfaces as implemented is mainly +intended to allow for modem dial-in / dial-out while still being able +to use a serial console on a (different) serial port. + +At the moment, the ports must be split on a SMC and a SCC port on a +8xx processor; other configurations are not (yet) supported. + +Support for hardware handshake has not been implemented yet (but is +in the works). + +*) The default console depends on the keys pressed: + - SMC if keys not pressed (modem not enabled) + - SCC if keys pressed (modem enabled) + +*) The console can be switched to SCC by any of the following commands: + + setenv stdout serial_scc + setenv stdin serial_scc + setenv stderr serial_scc + +*) The console can be switched to SMC by any of the following commands: + + setenv stdout serial_smc + setenv stdin serial_smc + setenv stderr serial_smc + +*) If a file descriptor is set to "serial" then the current serial device +will be used which, in turn, can be switched by above commands. + +*) The baudrate is the same for all serial devices. But it can be switched +just after switching the console: + + setenv sout serial_scc; setenv baudrate 38400 + +After that press 'enter' at the SCC console. Note that baudrates <38400 +are not allowed on LWMON with watchdog enabled (see CFG_BAUDRATE_TABLE in +include/configs/lwmon.h). diff --git a/drivers/Makefile b/drivers/Makefile index 11738b9999..afca70e2d0 100644 --- a/drivers/Makefile +++ b/drivers/Makefile @@ -29,23 +29,23 @@ LIB = libdrivers.a OBJS = 3c589.o 5701rls.o ali512x.o \ bcm570x.o bcm570x_autoneg.o cfb_console.o cfi_flash.o \ - cs8900.o ct69000.o dataflash.o dc2114x.o \ + cs8900.o ct69000.o dataflash.o dc2114x.o dm9000x.o \ e1000.o eepro100.o \ i8042.o i82365.o inca-ip_sw.o keyboard.o \ lan91c96.o natsemi.o netarm_eth.o \ - ns16550.o ns8382x.o ns87308.o \ + ns16550.o ns8382x.o ns87308.o omap1510_i2c.o \ pci.o pci_auto.o pci_indirect.o \ pcnet.o plb2800_eth.o \ ps2ser.o ps2mult.o pc_keyb.o \ rtl8019.o rtl8139.o rtl8169.o \ s3c24x0_i2c.o s3c4510b_eth.o s3c4510b_uart.o \ sed13806.o sed156x.o \ - serial.o serial_max3100.o serial_pl010.o serial_pl011.o \ - serial_xuartlite.o sl811_usb.o \ - smc91111.o smiLynxEM.o status_led.o sym53c8xx.o \ - ti_pci1410a.o tigon3.o w83c553f.o omap1510_i2c.o \ + serial.o serial_imx.o serial_max3100.o \ + serial_pl010.o serial_pl011.o serial_xuartlite.o \ + sl811_usb.o smc91111.o smiLynxEM.o status_led.o sym53c8xx.o \ + ti_pci1410a.o tigon3.o \ usbdcore.o usbdcore_ep0.o usbdcore_omap1510.o usbtty.o \ - videomodes.o + videomodes.o w83c553f.o all: $(LIB) diff --git a/drivers/cfb_console.c b/drivers/cfb_console.c index 6a8df79277..3d26ae2d50 100644 --- a/drivers/cfb_console.c +++ b/drivers/cfb_console.c @@ -1169,7 +1169,6 @@ int drv_video_init (void) { int skip_dev_init; device_t console_dev; - char *penv; skip_dev_init = 0; diff --git a/drivers/dm9000x.c b/drivers/dm9000x.c new file mode 100644 index 0000000000..0e475d4723 --- /dev/null +++ b/drivers/dm9000x.c @@ -0,0 +1,590 @@ +/* + dm9000.c: Version 1.2 12/15/2003 + + A Davicom DM9000 ISA NIC fast Ethernet driver for Linux. + Copyright (C) 1997 Sten Wang + + This program is free software; you can redistribute it and/or + modify it under the terms of the GNU General Public License + as published by the Free Software Foundation; either version 2 + of the License, or (at your option) any later version. + + This program is distributed in the hope that it will be useful, + but WITHOUT ANY WARRANTY; without even the implied warranty of + MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + GNU General Public License for more details. + + (C)Copyright 1997-1998 DAVICOM Semiconductor,Inc. All Rights Reserved. + +V0.11 06/20/2001 REG_0A bit3=1, default enable BP with DA match + 06/22/2001 Support DM9801 progrmming + E3: R25 = ((R24 + NF) & 0x00ff) | 0xf000 + E4: R25 = ((R24 + NF) & 0x00ff) | 0xc200 + R17 = (R17 & 0xfff0) | NF + 3 + E5: R25 = ((R24 + NF - 3) & 0x00ff) | 0xc200 + R17 = (R17 & 0xfff0) | NF + +v1.00 modify by simon 2001.9.5 + change for kernel 2.4.x + +v1.1 11/09/2001 fix force mode bug + +v1.2 03/18/2003 Weilun Huang : + Fixed phy reset. + Added tx/rx 32 bit mode. + Cleaned up for kernel merge. + +-------------------------------------- + + 12/15/2003 Initial port to u-boot by Sascha Hauer + +TODO: Homerun NIC and longrun NIC are not functional, only internal at the + moment. +*/ + +#include +#include +#include +#include + +#ifdef CONFIG_DRIVER_DM9000 + +#include "dm9000x.h" + +/* Board/System/Debug information/definition ---------------- */ + +#define DM9801_NOISE_FLOOR 0x08 +#define DM9802_NOISE_FLOOR 0x05 + +/* #define CONFIG_DM9000_DEBUG */ + +#ifdef CONFIG_DM9000_DEBUG +#define DM9000_DBG(fmt,args...) printf(fmt ,##args) +#else /* */ +#define DM9000_DBG(fmt,args...) +#endif /* */ +enum DM9000_PHY_mode { DM9000_10MHD = 0, DM9000_100MHD = + 1, DM9000_10MFD = 4, DM9000_100MFD = 5, DM9000_AUTO = + 8, DM9000_1M_HPNA = 0x10 +}; +enum DM9000_NIC_TYPE { FASTETHER_NIC = 0, HOMERUN_NIC = 1, LONGRUN_NIC = 2 +}; + +/* Structure/enum declaration ------------------------------- */ +typedef struct board_info { + u32 runt_length_counter; /* counter: RX length < 64byte */ + u32 long_length_counter; /* counter: RX length > 1514byte */ + u32 reset_counter; /* counter: RESET */ + u32 reset_tx_timeout; /* RESET caused by TX Timeout */ + u32 reset_rx_status; /* RESET caused by RX Statsus wrong */ + u16 tx_pkt_cnt; + u16 queue_start_addr; + u16 dbug_cnt; + u8 phy_addr; + u8 device_wait_reset; /* device state */ + u8 nic_type; /* NIC type */ + unsigned char srom[128]; +} board_info_t; +board_info_t dmfe_info; + +/* For module input parameter */ +static int media_mode = DM9000_AUTO; +static u8 nfloor = 0; + +/* function declaration ------------------------------------- */ +int eth_init(bd_t * bd); +int eth_send(volatile void *, int); +int eth_rx(void); +void eth_halt(void); +static int dm9000_probe(void); +static u16 phy_read(int); +static void phy_write(int, u16); +static u16 read_srom_word(int); +static u8 DM9000_ior(int); +static void DM9000_iow(int reg, u8 value); + +/* DM9000 network board routine ---------------------------- */ + +#define DM9000_outb(d,r) ( *(volatile u8 *)r = d ) +#define DM9000_outw(d,r) ( *(volatile u16 *)r = d ) +#define DM9000_outl(d,r) ( *(volatile u32 *)r = d ) +#define DM9000_inb(r) (*(volatile u8 *)r) +#define DM9000_inw(r) (*(volatile u16 *)r) +#define DM9000_inl(r) (*(volatile u32 *)r) + +#ifdef CONFIG_DM9000_DEBUG +static void +dump_regs(void) +{ + DM9000_DBG("\n"); + DM9000_DBG("NCR (0x00): %02x\n", DM9000_ior(0)); + DM9000_DBG("NSR (0x01): %02x\n", DM9000_ior(1)); + DM9000_DBG("TCR (0x02): %02x\n", DM9000_ior(2)); + DM9000_DBG("TSRI (0x03): %02x\n", DM9000_ior(3)); + DM9000_DBG("TSRII (0x04): %02x\n", DM9000_ior(4)); + DM9000_DBG("RCR (0x05): %02x\n", DM9000_ior(5)); + DM9000_DBG("RSR (0x06): %02x\n", DM9000_ior(6)); + DM9000_DBG("ISR (0xFE): %02x\n", DM9000_ior(ISR)); + DM9000_DBG("\n"); +} +#endif /* */ + +/* + Search DM9000 board, allocate space and register it +*/ +int +dm9000_probe(void) +{ + u32 id_val; + id_val = DM9000_ior(DM9000_VIDL); + id_val |= DM9000_ior(DM9000_VIDH) << 8; + id_val |= DM9000_ior(DM9000_PIDL) << 16; + id_val |= DM9000_ior(DM9000_PIDH) << 24; + if (id_val == DM9000_ID) { + printf("dm9000 i/o: 0x%x, id: 0x%x \n", CONFIG_DM9000_BASE, + id_val); + return 0; + } else { + printf("dm9000 not found at 0x%08x id: 0x%08x\n", + CONFIG_DM9000_BASE, id_val); + return -1; + } +} + +/* Set PHY operationg mode +*/ +static void +set_PHY_mode(void) +{ + u16 phy_reg4 = 0x01e1, phy_reg0 = 0x1000; + if (!(media_mode & DM9000_AUTO)) { + switch (media_mode) { + case DM9000_10MHD: + phy_reg4 = 0x21; + phy_reg0 = 0x0000; + break; + case DM9000_10MFD: + phy_reg4 = 0x41; + phy_reg0 = 0x1100; + break; + case DM9000_100MHD: + phy_reg4 = 0x81; + phy_reg0 = 0x2000; + break; + case DM9000_100MFD: + phy_reg4 = 0x101; + phy_reg0 = 0x3100; + break; + } + phy_write(4, phy_reg4); /* Set PHY media mode */ + phy_write(0, phy_reg0); /* Tmp */ + } + DM9000_iow(DM9000_GPCR, 0x01); /* Let GPIO0 output */ + DM9000_iow(DM9000_GPR, 0x00); /* Enable PHY */ +} + +/* + Init HomeRun DM9801 +*/ +static void +program_dm9801(u16 HPNA_rev) +{ + __u16 reg16, reg17, reg24, reg25; + if (!nfloor) + nfloor = DM9801_NOISE_FLOOR; + reg16 = phy_read(16); + reg17 = phy_read(17); + reg24 = phy_read(24); + reg25 = phy_read(25); + switch (HPNA_rev) { + case 0xb900: /* DM9801 E3 */ + reg16 |= 0x1000; + reg25 = ((reg24 + nfloor) & 0x00ff) | 0xf000; + break; + case 0xb901: /* DM9801 E4 */ + reg25 = ((reg24 + nfloor) & 0x00ff) | 0xc200; + reg17 = (reg17 & 0xfff0) + nfloor + 3; + break; + case 0xb902: /* DM9801 E5 */ + case 0xb903: /* DM9801 E6 */ + default: + reg16 |= 0x1000; + reg25 = ((reg24 + nfloor - 3) & 0x00ff) | 0xc200; + reg17 = (reg17 & 0xfff0) + nfloor; + } + phy_write(16, reg16); + phy_write(17, reg17); + phy_write(25, reg25); +} + +/* + Init LongRun DM9802 +*/ +static void +program_dm9802(void) +{ + __u16 reg25; + if (!nfloor) + nfloor = DM9802_NOISE_FLOOR; + reg25 = phy_read(25); + reg25 = (reg25 & 0xff00) + nfloor; + phy_write(25, reg25); +} + +/* Identify NIC type +*/ +static void +identify_nic(void) +{ + struct board_info *db = &dmfe_info; /* Point a board information structure */ + u16 phy_reg3; + DM9000_iow(DM9000_NCR, NCR_EXT_PHY); + phy_reg3 = phy_read(3); + switch (phy_reg3 & 0xfff0) { + case 0xb900: + if (phy_read(31) == 0x4404) { + db->nic_type = HOMERUN_NIC; + program_dm9801(phy_reg3); + DM9000_DBG("found homerun NIC\n"); + } else { + db->nic_type = LONGRUN_NIC; + DM9000_DBG("found longrun NIC\n"); + program_dm9802(); + } + break; + default: + db->nic_type = FASTETHER_NIC; + break; + } + DM9000_iow(DM9000_NCR, 0); +} + +/* General Purpose dm9000 reset routine */ +static void +dm9000_reset(void) +{ + DM9000_DBG("resetting\n"); + DM9000_iow(DM9000_NCR, NCR_RST); + udelay(1000); /* delay 1ms */ +} + +/* Initilize dm9000 board +*/ +int +eth_init(bd_t * bd) +{ + int i, oft, lnk; + DM9000_DBG("eth_init()\n"); + + /* RESET device */ + dm9000_reset(); + dm9000_probe(); + + /* NIC Type: FASTETHER, HOMERUN, LONGRUN */ + identify_nic(); + + /* GPIO0 on pre-activate PHY */ + DM9000_iow(DM9000_GPR, 0x00); /*REG_1F bit0 activate phyxcer */ + + /* Set PHY */ + set_PHY_mode(); + + /* Program operating register */ + DM9000_iow(DM9000_NCR, 0x0); /* only intern phy supported by now */ + DM9000_iow(DM9000_TCR, 0); /* TX Polling clear */ + DM9000_iow(DM9000_BPTR, 0x3f); /* Less 3Kb, 200us */ + DM9000_iow(DM9000_FCTR, FCTR_HWOT(3) | FCTR_LWOT(8)); /* Flow Control : High/Low Water */ + DM9000_iow(DM9000_FCR, 0x0); /* SH FIXME: This looks strange! Flow Control */ + DM9000_iow(DM9000_SMCR, 0); /* Special Mode */ + DM9000_iow(DM9000_NSR, NSR_WAKEST | NSR_TX2END | NSR_TX1END); /* clear TX status */ + DM9000_iow(DM9000_ISR, 0x0f); /* Clear interrupt status */ + + /* Set Node address */ + for (i = 0; i < 6; i++) + ((u16 *) bd->bi_enetaddr)[i] = read_srom_word(i); + printf("MAC: %02x:%02x:%02x:%02x:%02x:%02x\n", bd->bi_enetaddr[0], + bd->bi_enetaddr[1], bd->bi_enetaddr[2], bd->bi_enetaddr[3], + bd->bi_enetaddr[4], bd->bi_enetaddr[5]); + for (i = 0, oft = 0x10; i < 6; i++, oft++) + DM9000_iow(oft, bd->bi_enetaddr[i]); + for (i = 0, oft = 0x16; i < 8; i++, oft++) + DM9000_iow(oft, 0xff); + + /* read back mac, just to be sure */ + for (i = 0, oft = 0x10; i < 6; i++, oft++) + DM9000_DBG("%02x:", DM9000_ior(oft)); + DM9000_DBG("\n"); + + /* Activate DM9000 */ + DM9000_iow(DM9000_RCR, RCR_DIS_LONG | RCR_DIS_CRC | RCR_RXEN); /* RX enable */ + DM9000_iow(DM9000_IMR, IMR_PAR); /* Enable TX/RX interrupt mask */ + i = 0; + while (!(phy_read(1) & 0x20)) { /* autonegation complete bit */ + udelay(1000); + i++; + if (i == 10000) { + printf("could not establish link\n"); + return 0; + } + } + + /* see what we've got */ + lnk = phy_read(17) >> 12; + printf("operating at "); + switch (lnk) { + case 1: + printf("10M half duplex "); + break; + case 2: + printf("10M full duplex "); + break; + case 4: + printf("100M half duplex "); + break; + case 8: + printf("100M full duplex "); + break; + default: + printf("unknown: %d ", lnk); + break; + } + printf("mode\n"); + return 0; +} + +/* + Hardware start transmission. + Send a packet to media from the upper layer. +*/ +int +eth_send(volatile void *packet, int length) +{ + char *data_ptr; + u32 tmplen, i; + int tmo; + DM9000_DBG("eth_send: length: %d\n", length); + for (i = 0; i < length; i++) { + if (i % 8 == 0) + DM9000_DBG("\nSend: 02x: ", i); + DM9000_DBG("%02x ", ((unsigned char *) packet)[i]); + } DM9000_DBG("\n"); + + /* Move data to DM9000 TX RAM */ + data_ptr = (char *) packet; + DM9000_outb(DM9000_MWCMD, DM9000_IO); + +#ifdef CONFIG_DM9000_USE_8BIT + /* Byte mode */ + for (i = 0; i < length; i++) + DM9000_outb((data_ptr[i] & 0xff), DM9000_DATA); + +#endif /* */ +#ifdef CONFIG_DM9000_USE_16BIT + tmplen = (length + 1) / 2; + for (i = 0; i < tmplen; i++) + DM9000_outw(((u16 *) data_ptr)[i], DM9000_DATA); + +#endif /* */ +#ifdef CONFIG_DM9000_USE_32BIT + tmplen = (length + 3) / 4; + for (i = 0; i < tmplen; i++) + DM9000_outl(((u32 *) data_ptr)[i], DM9000_DATA); + +#endif /* */ + + /* Set TX length to DM9000 */ + DM9000_iow(DM9000_TXPLL, length & 0xff); + DM9000_iow(DM9000_TXPLH, (length >> 8) & 0xff); + + /* Issue TX polling command */ + DM9000_iow(DM9000_TCR, TCR_TXREQ); /* Cleared after TX complete */ + + /* wait for end of transmission */ + tmo = get_timer(0) + 5 * CFG_HZ; + while (DM9000_ior(DM9000_TCR) & TCR_TXREQ) { + if (get_timer(0) >= tmo) { + printf("transmission timeout\n"); + break; + } + } + DM9000_DBG("transmit done\n\n"); + return 0; +} + +/* + Stop the interface. + The interface is stopped when it is brought. +*/ +void +eth_halt(void) +{ + DM9000_DBG("eth_halt\n"); + + /* RESET devie */ + phy_write(0, 0x8000); /* PHY RESET */ + DM9000_iow(DM9000_GPR, 0x01); /* Power-Down PHY */ + DM9000_iow(DM9000_IMR, 0x80); /* Disable all interrupt */ + DM9000_iow(DM9000_RCR, 0x00); /* Disable RX */ +} + +/* + Received a packet and pass to upper layer +*/ +int +eth_rx(void) +{ + u8 rxbyte, *rdptr = (u8 *) NetRxPackets[0]; + u16 RxStatus, RxLen = 0; + u32 tmplen, i; + + /* Check packet ready or not */ + DM9000_ior(DM9000_MRCMDX); /* Dummy read */ + rxbyte = DM9000_inb(DM9000_DATA); /* Got most updated data */ + if (rxbyte == 0) + return 0; + + /* Status check: this byte must be 0 or 1 */ + if (rxbyte > 1) { + DM9000_iow(DM9000_RCR, 0x00); /* Stop Device */ + DM9000_iow(DM9000_ISR, 0x80); /* Stop INT request */ + DM9000_DBG("rx status check: %d\n", rxbyte); + } + DM9000_DBG("receiving packet\n"); + + /* A packet ready now & Get status/length */ + DM9000_outb(DM9000_MRCMD, DM9000_IO); + +#ifdef CONFIG_DM9000_USE_8BIT + RxStatus = DM9000_inb(DM9000_DATA) + (DM9000_inb(DM9000_DATA) << 8); + RxLen = DM9000_inb(DM9000_DATA) + (DM9000_inb(DM9000_DATA) << 8); + +#endif /* */ +#ifdef CONFIG_DM9000_USE_16BIT + RxStatus = DM9000_inw(DM9000_DATA); + RxLen = DM9000_inw(DM9000_DATA); + +#endif /* */ +#ifdef CONFIG_DM9000_USE_32BIT + tmpdata = DM9000_inl(DM9000_DATA); + RxStatus = tmpdata; + RxLen = tmpdata >> 16; + +#endif /* */ + DM9000_DBG("rx status: 0x%04x rx len: %d\n", RxStatus, RxLen); + + /* Move data from DM9000 */ + /* Read received packet from RX SRAM */ +#ifdef CONFIG_DM9000_USE_8BIT + for (i = 0; i < RxLen; i++) + rdptr[i] = DM9000_inb(DM9000_DATA); + +#endif /* */ +#ifdef CONFIG_DM9000_USE_16BIT + tmplen = (RxLen + 1) / 2; + for (i = 0; i < tmplen; i++) + ((u16 *) rdptr)[i] = DM9000_inw(DM9000_DATA); + +#endif /* */ +#ifdef CONFIG_DM9000_USE_32BIT + tmplen = (RxLen + 3) / 4; + for (i = 0; i < tmplen; i++) + ((u32 *) rdptr)[i] = DM9000_inl(DM9000_DATA); + +#endif /* */ + if ((RxStatus & 0xbf00) || (RxLen < 0x40) + || (RxLen > DM9000_PKT_MAX)) { + if (RxStatus & 0x100) { + printf("rx fifo error\n"); + } + if (RxStatus & 0x200) { + printf("rx crc error\n"); + } + if (RxStatus & 0x8000) { + printf("rx length error\n"); + } + if (RxLen > DM9000_PKT_MAX) { + printf("rx length too big\n"); + dm9000_reset(); + } + } else { + + /* Pass to upper layer */ + DM9000_DBG("passing packet to upper layer\n"); + NetReceive(NetRxPackets[0], RxLen); + return RxLen; + } + return 0; +} + +/* + Read a word data from SROM +*/ +static u16 +read_srom_word(int offset) +{ + DM9000_iow(DM9000_EPAR, offset); + DM9000_iow(DM9000_EPCR, 0x4); + udelay(200); + DM9000_iow(DM9000_EPCR, 0x0); + return (DM9000_ior(DM9000_EPDRL) + (DM9000_ior(DM9000_EPDRH) << 8)); +} + +/* + Read a byte from I/O port +*/ +static u8 +DM9000_ior(int reg) +{ + DM9000_outb(reg, DM9000_IO); + return DM9000_inb(DM9000_DATA); +} + +/* + Write a byte to I/O port +*/ +static void +DM9000_iow(int reg, u8 value) +{ + DM9000_outb(reg, DM9000_IO); + DM9000_outb(value, DM9000_DATA); +} + +/* + Read a word from phyxcer +*/ +static u16 +phy_read(int reg) +{ + u16 val; + + /* Fill the phyxcer register into REG_0C */ + DM9000_iow(DM9000_EPAR, DM9000_PHY | reg); + DM9000_iow(DM9000_EPCR, 0xc); /* Issue phyxcer read command */ + udelay(100); /* Wait read complete */ + DM9000_iow(DM9000_EPCR, 0x0); /* Clear phyxcer read command */ + val = (DM9000_ior(DM9000_EPDRH) << 8) | DM9000_ior(DM9000_EPDRL); + + /* The read data keeps on REG_0D & REG_0E */ + DM9000_DBG("phy_read(%d): %d\n", reg, val); + return val; +} + +/* + Write a word to phyxcer +*/ +static void +phy_write(int reg, u16 value) +{ + + /* Fill the phyxcer register into REG_0C */ + DM9000_iow(DM9000_EPAR, DM9000_PHY | reg); + + /* Fill the written data into REG_0D & REG_0E */ + DM9000_iow(DM9000_EPDRL, (value & 0xff)); + DM9000_iow(DM9000_EPDRH, ((value >> 8) & 0xff)); + DM9000_iow(DM9000_EPCR, 0xa); /* Issue phyxcer write command */ + udelay(500); /* Wait write complete */ + DM9000_iow(DM9000_EPCR, 0x0); /* Clear phyxcer write command */ + DM9000_DBG("phy_write(reg:%d, value:%d)\n", reg, value); +} +#endif /* CONFIG_DRIVER_DM9000 */ diff --git a/drivers/dm9000x.h b/drivers/dm9000x.h new file mode 100644 index 0000000000..f47ff8cb34 --- /dev/null +++ b/drivers/dm9000x.h @@ -0,0 +1,119 @@ +/* + * dm9000 Ethernet + */ + +#ifdef CONFIG_DRIVER_DM9000 + +#define DM9000_ID 0x90000A46 +#define DM9000_PKT_MAX 1536 /* Received packet max size */ +#define DM9000_PKT_RDY 0x01 /* Packet ready to receive */ + +/* although the registers are 16 bit, they are 32-bit aligned. + */ + +#define DM9000_NCR 0x00 +#define DM9000_NSR 0x01 +#define DM9000_TCR 0x02 +#define DM9000_TSR1 0x03 +#define DM9000_TSR2 0x04 +#define DM9000_RCR 0x05 +#define DM9000_RSR 0x06 +#define DM9000_ROCR 0x07 +#define DM9000_BPTR 0x08 +#define DM9000_FCTR 0x09 +#define DM9000_FCR 0x0A +#define DM9000_EPCR 0x0B +#define DM9000_EPAR 0x0C +#define DM9000_EPDRL 0x0D +#define DM9000_EPDRH 0x0E +#define DM9000_WCR 0x0F + +#define DM9000_PAR 0x10 +#define DM9000_MAR 0x16 + +#define DM9000_GPCR 0x1e +#define DM9000_GPR 0x1f +#define DM9000_TRPAL 0x22 +#define DM9000_TRPAH 0x23 +#define DM9000_RWPAL 0x24 +#define DM9000_RWPAH 0x25 + +#define DM9000_VIDL 0x28 +#define DM9000_VIDH 0x29 +#define DM9000_PIDL 0x2A +#define DM9000_PIDH 0x2B + +#define DM9000_CHIPR 0x2C +#define DM9000_SMCR 0x2F + +#define DM9000_PHY 0x40 /* PHY address 0x01 */ + +#define DM9000_MRCMDX 0xF0 +#define DM9000_MRCMD 0xF2 +#define DM9000_MRRL 0xF4 +#define DM9000_MRRH 0xF5 +#define DM9000_MWCMDX 0xF6 +#define DM9000_MWCMD 0xF8 +#define DM9000_MWRL 0xFA +#define DM9000_MWRH 0xFB +#define DM9000_TXPLL 0xFC +#define DM9000_TXPLH 0xFD +#define DM9000_ISR 0xFE +#define DM9000_IMR 0xFF + +#define NCR_EXT_PHY (1<<7) +#define NCR_WAKEEN (1<<6) +#define NCR_FCOL (1<<4) +#define NCR_FDX (1<<3) +#define NCR_LBK (3<<1) +#define NCR_RST (1<<0) + +#define NSR_SPEED (1<<7) +#define NSR_LINKST (1<<6) +#define NSR_WAKEST (1<<5) +#define NSR_TX2END (1<<3) +#define NSR_TX1END (1<<2) +#define NSR_RXOV (1<<1) + +#define TCR_TJDIS (1<<6) +#define TCR_EXCECM (1<<5) +#define TCR_PAD_DIS2 (1<<4) +#define TCR_CRC_DIS2 (1<<3) +#define TCR_PAD_DIS1 (1<<2) +#define TCR_CRC_DIS1 (1<<1) +#define TCR_TXREQ (1<<0) + +#define TSR_TJTO (1<<7) +#define TSR_LC (1<<6) +#define TSR_NC (1<<5) +#define TSR_LCOL (1<<4) +#define TSR_COL (1<<3) +#define TSR_EC (1<<2) + +#define RCR_WTDIS (1<<6) +#define RCR_DIS_LONG (1<<5) +#define RCR_DIS_CRC (1<<4) +#define RCR_ALL (1<<3) +#define RCR_RUNT (1<<2) +#define RCR_PRMSC (1<<1) +#define RCR_RXEN (1<<0) + +#define RSR_RF (1<<7) +#define RSR_MF (1<<6) +#define RSR_LCS (1<<5) +#define RSR_RWTO (1<<4) +#define RSR_PLE (1<<3) +#define RSR_AE (1<<2) +#define RSR_CE (1<<1) +#define RSR_FOE (1<<0) + +#define FCTR_HWOT(ot) (( ot & 0xf ) << 4 ) +#define FCTR_LWOT(ot) ( ot & 0xf ) + +#define IMR_PAR (1<<7) +#define IMR_ROOM (1<<3) +#define IMR_ROM (1<<2) +#define IMR_PTM (1<<1) +#define IMR_PRM (1<<0) + +#endif diff --git a/drivers/serial_imx.c b/drivers/serial_imx.c new file mode 100644 index 0000000000..9dbaa569a0 --- /dev/null +++ b/drivers/serial_imx.c @@ -0,0 +1,201 @@ +/* + * (c) 2004 Sascha Hauer + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + * + */ + +#include +#if defined (CONFIG_IMX) + +#include + +#ifndef CONFIG_IMX_SERIAL_NONE + +#if defined CONFIG_IMX_SERIAL1 +#define UART_BASE IMX_UART1_BASE +#elif defined CONFIG_IMX_SERIAL2 +#define UART_BASE IMX_UART2_BASE +#else +#error "define CONFIG_IMX_SERIAL1, CONFIG_IMX_SERIAL2 or CONFIG_IMX_SERIAL_NONE" +#endif + +struct imx_serial { + volatile uint32_t urxd[16]; + volatile uint32_t utxd[16]; + volatile uint32_t ucr1; + volatile uint32_t ucr2; + volatile uint32_t ucr3; + volatile uint32_t ucr4; + volatile uint32_t ufcr; + volatile uint32_t usr1; + volatile uint32_t usr2; + volatile uint32_t uesc; + volatile uint32_t utim; + volatile uint32_t ubir; + volatile uint32_t ubmr; + volatile uint32_t ubrc; + volatile uint32_t bipr[4]; + volatile uint32_t bmpr[4]; + volatile uint32_t uts; +}; + +void serial_setbrg (void) +{ + serial_init(); +} + +extern void imx_gpio_mode(int gpio_mode); + +/* + * Initialise the serial port with the given baudrate. The settings + * are always 8 data bits, no parity, 1 stop bit, no start bits. + * + */ +int serial_init (void) +{ + volatile struct imx_serial* base = (struct imx_serial *)UART_BASE; +#ifdef CONFIG_IMX_SERIAL1 + imx_gpio_mode(PC11_PF_UART1_TXD); + imx_gpio_mode(PC12_PF_UART1_RXD); +#else + imx_gpio_mode(PB30_PF_UART2_TXD); + imx_gpio_mode(PB31_PF_UART2_RXD); +#endif + + /* Disable UART */ + base->ucr1 &= ~UCR1_UARTEN; + + /* Set to default POR state */ + + base->ucr1 = 0x00000004; + base->ucr2 = 0x00000000; + base->ucr3 = 0x00000000; + base->ucr4 = 0x00008040; + base->uesc = 0x0000002B; + base->utim = 0x00000000; + base->ubir = 0x00000000; + base->ubmr = 0x00000000; + base->uts = 0x00000000; + /* Set clocks */ + base->ucr4 |= UCR4_REF16; + + /* Configure FIFOs */ + base->ufcr = 0xa81; + + /* Set the numerator value minus one of the BRM ratio */ + base->ubir = (CONFIG_BAUDRATE / 100) - 1; + + /* Set the denominator value minus one of the BRM ratio */ + base->ubmr = 10000 - 1; + + /* Set to 8N1 */ + base->ucr2 &= ~UCR2_PREN; + base->ucr2 |= UCR2_WS; + base->ucr2 &= ~UCR2_STPB; + + /* Ignore RTS */ + base->ucr2 |= UCR2_IRTS; + + /* Enable UART */ + base->ucr1 |= UCR1_UARTEN | UCR1_UARTCLKEN; + + /* Enable FIFOs */ + base->ucr2 |= UCR2_SRST | UCR2_RXEN | UCR2_TXEN; + + /* Clear status flags */ + base->usr2 |= USR2_ADET | + USR2_DTRF | + USR2_IDLE | + USR2_IRINT | + USR2_WAKE | + USR2_RTSF | + USR2_BRCD | + USR2_ORE | + USR2_RDR; + + /* Clear status flags */ + base->usr1 |= USR1_PARITYERR | + USR1_RTSD | + USR1_ESCF | + USR1_FRAMERR | + USR1_AIRINT | + USR1_AWAKE; + return (0); +} + +/* + * Read a single byte from the serial port. Returns 1 on success, 0 + * otherwise. When the function is successful, the character read is + * written into its argument c. + */ +int serial_getc (void) +{ + volatile struct imx_serial* base = (struct imx_serial *)UART_BASE; + unsigned char ch; + + while(base->uts & UTS_RXEMPTY); + + ch = (char)base->urxd[0]; + + return ch; +} + +#ifdef CONFIG_HWFLOW +static int hwflow = 0; /* turned off by default */ +int hwflow_onoff(int on) +{ +} +#endif + +/* + * Output a single byte to the serial port. + */ +void serial_putc (const char c) +{ + volatile struct imx_serial* base = (struct imx_serial *)UART_BASE; + + /* Wait for Tx FIFO not full */ + while (base->uts & UTS_TXFULL); + + base->utxd[0] = c; + + /* If \n, also do \r */ + if (c == '\n') + serial_putc ('\r'); +} + +/* + * Test whether a character is in the RX buffer + */ +int serial_tstc (void) +{ + volatile struct imx_serial* base = (struct imx_serial *)UART_BASE; + + /* If receive fifo is empty, return false */ + if (base->uts & UTS_RXEMPTY) + return 0; + return 1; +} + +void +serial_puts (const char *s) +{ + while (*s) { + serial_putc (*s++); + } +} +#endif /* CONFIG_IMX_SERIAL_NONE */ +#endif /* defined CONFIG_IMX */ diff --git a/include/asm-arm/arch-arm920t/imx-regs.h b/include/asm-arm/arch-arm920t/imx-regs.h new file mode 100644 index 0000000000..1486b74c2a --- /dev/null +++ b/include/asm-arm/arch-arm920t/imx-regs.h @@ -0,0 +1,571 @@ +#ifndef _IMX_REGS_H +#define _IMX_REGS_H +/* ------------------------------------------------------------------------ + * Motorola IMX system registers + * ------------------------------------------------------------------------ + * + */ + +# ifndef __ASSEMBLY__ +# define __REG(x) (*((volatile u32 *)(x))) +# define __REG2(x,y) \ + ( __builtin_constant_p(y) ? (__REG((x) + (y))) \ + : (*(volatile u32 *)((u32)&__REG(x) + (y))) ) +# else +# define __REG(x) (x) +# define __REG2(x,y) ((x)+(y)) +#endif + +#define IMX_IO_BASE 0x00200000 + +/* + * Register BASEs, based on OFFSETs + * + */ +#define IMX_AIPI1_BASE (0x00000 + IMX_IO_BASE) +#define IMX_WDT_BASE (0x01000 + IMX_IO_BASE) +#define IMX_TIM1_BASE (0x02000 + IMX_IO_BASE) +#define IMX_TIM2_BASE (0x03000 + IMX_IO_BASE) +#define IMX_RTC_BASE (0x04000 + IMX_IO_BASE) +#define IMX_LCDC_BASE (0x05000 + IMX_IO_BASE) +#define IMX_UART1_BASE (0x06000 + IMX_IO_BASE) +#define IMX_UART2_BASE (0x07000 + IMX_IO_BASE) +#define IMX_PWM_BASE (0x08000 + IMX_IO_BASE) +#define IMX_DMAC_BASE (0x09000 + IMX_IO_BASE) +#define IMX_AIPI2_BASE (0x10000 + IMX_IO_BASE) +#define IMX_SIM_BASE (0x11000 + IMX_IO_BASE) +#define IMX_USBD_BASE (0x12000 + IMX_IO_BASE) +#define IMX_SPI1_BASE (0x13000 + IMX_IO_BASE) +#define IMX_MMC_BASE (0x14000 + IMX_IO_BASE) +#define IMX_ASP_BASE (0x15000 + IMX_IO_BASE) +#define IMX_BTA_BASE (0x16000 + IMX_IO_BASE) +#define IMX_I2C_BASE (0x17000 + IMX_IO_BASE) +#define IMX_SSI_BASE (0x18000 + IMX_IO_BASE) +#define IMX_SPI2_BASE (0x19000 + IMX_IO_BASE) +#define IMX_MSHC_BASE (0x1A000 + IMX_IO_BASE) +#define IMX_PLL_BASE (0x1B000 + IMX_IO_BASE) +#define IMX_SYSCTRL_BASE (0x1B800 + IMX_IO_BASE) +#define IMX_GPIO_BASE (0x1C000 + IMX_IO_BASE) +#define IMX_EIM_BASE (0x20000 + IMX_IO_BASE) +#define IMX_SDRAMC_BASE (0x21000 + IMX_IO_BASE) +#define IMX_MMA_BASE (0x22000 + IMX_IO_BASE) +#define IMX_AITC_BASE (0x23000 + IMX_IO_BASE) +#define IMX_CSI_BASE (0x24000 + IMX_IO_BASE) + +/* SYSCTRL Registers */ +#define SIDR __REG(IMX_SYSCTRL_BASE + 0x4) /* Silicon ID Register */ +#define FMCR __REG(IMX_SYSCTRL_BASE + 0x8) /* Function Multiplex Control Register */ +#define GPCR __REG(IMX_SYSCTRL_BASE + 0xC) /* Function Multiplex Control Register */ + +/* Chip Select Registers */ +#define CS0U __REG(IMX_EIM_BASE) /* Chip Select 0 Upper Register */ +#define CS0L __REG(IMX_EIM_BASE + 0x4) /* Chip Select 0 Lower Register */ +#define CS1U __REG(IMX_EIM_BASE + 0x8) /* Chip Select 1 Upper Register */ +#define CS1L __REG(IMX_EIM_BASE + 0xc) /* Chip Select 1 Lower Register */ +#define CS2U __REG(IMX_EIM_BASE + 0x10) /* Chip Select 2 Upper Register */ +#define CS2L __REG(IMX_EIM_BASE + 0x14) /* Chip Select 2 Lower Register */ +#define CS3U __REG(IMX_EIM_BASE + 0x18) /* Chip Select 3 Upper Register */ +#define CS3L __REG(IMX_EIM_BASE + 0x1c) /* Chip Select 3 Lower Register */ +#define CS4U __REG(IMX_EIM_BASE + 0x20) /* Chip Select 4 Upper Register */ +#define CS4L __REG(IMX_EIM_BASE + 0x24) /* Chip Select 4 Lower Register */ +#define CS5U __REG(IMX_EIM_BASE + 0x28) /* Chip Select 5 Upper Register */ +#define CS5L __REG(IMX_EIM_BASE + 0x2c) /* Chip Select 5 Lower Register */ +#define EIM __REG(IMX_EIM_BASE + 0x30) /* EIM Configuration Register */ + +/* SDRAM controller registers */ + +#define SDCTL0 __REG(IMX_SDRAMC_BASE) /* SDRAM 0 Control Register */ +#define SDCTL1 __REG(IMX_SDRAMC_BASE + 0x4) /* SDRAM 1 Control Register */ +#define SDMISC __REG(IMX_SDRAMC_BASE + 0x14) /* Miscellaneous Register */ +#define SDRST __REG(IMX_SDRAMC_BASE + 0x18) /* SDRAM Reset Register */ + +/* PLL registers */ +#define CSCR __REG(IMX_PLL_BASE) /* Clock Source Control Register */ +#define MPCTL0 __REG(IMX_PLL_BASE + 0x4) /* MCU PLL Control Register 0 */ +#define MPCTL1 __REG(IMX_PLL_BASE + 0x8) /* MCU PLL and System Clock Register 1 */ +#define SPCTL0 __REG(IMX_PLL_BASE + 0xc) /* System PLL Control Register 0 */ +#define SPCTL1 __REG(IMX_PLL_BASE + 0x10) /* System PLL Control Register 1 */ +#define PCDR __REG(IMX_PLL_BASE + 0x20) /* Peripheral Clock Divider Register */ + +#define CSCR_MPLL_RESTART (1<<21) + +/* + * GPIO Module and I/O Multiplexer + * x = 0..3 for reg_A, reg_B, reg_C, reg_D + */ +#define DDIR(x) __REG2(IMX_GPIO_BASE + 0x00, ((x) & 3) << 8) +#define OCR1(x) __REG2(IMX_GPIO_BASE + 0x04, ((x) & 3) << 8) +#define OCR2(x) __REG2(IMX_GPIO_BASE + 0x08, ((x) & 3) << 8) +#define ICONFA1(x) __REG2(IMX_GPIO_BASE + 0x0c, ((x) & 3) << 8) +#define ICONFA2(x) __REG2(IMX_GPIO_BASE + 0x10, ((x) & 3) << 8) +#define ICONFB1(x) __REG2(IMX_GPIO_BASE + 0x14, ((x) & 3) << 8) +#define ICONFB2(x) __REG2(IMX_GPIO_BASE + 0x18, ((x) & 3) << 8) +#define DR(x) __REG2(IMX_GPIO_BASE + 0x1c, ((x) & 3) << 8) +#define GIUS(x) __REG2(IMX_GPIO_BASE + 0x20, ((x) & 3) << 8) +#define SSR(x) __REG2(IMX_GPIO_BASE + 0x24, ((x) & 3) << 8) +#define ICR1(x) __REG2(IMX_GPIO_BASE + 0x28, ((x) & 3) << 8) +#define ICR2(x) __REG2(IMX_GPIO_BASE + 0x2c, ((x) & 3) << 8) +#define IMR(x) __REG2(IMX_GPIO_BASE + 0x30, ((x) & 3) << 8) +#define ISR(x) __REG2(IMX_GPIO_BASE + 0x34, ((x) & 3) << 8) +#define GPR(x) __REG2(IMX_GPIO_BASE + 0x38, ((x) & 3) << 8) +#define SWR(x) __REG2(IMX_GPIO_BASE + 0x3c, ((x) & 3) << 8) +#define PUEN(x) __REG2(IMX_GPIO_BASE + 0x40, ((x) & 3) << 8) + +#define GPIO_PIN_MASK 0x1f +#define GPIO_PORT_MASK (0x3 << 5) + +#define GPIO_PORTA (0<<5) +#define GPIO_PORTB (1<<5) +#define GPIO_PORTC (2<<5) +#define GPIO_PORTD (3<<5) + +#define GPIO_OUT (1<<7) +#define GPIO_IN (0<<7) +#define GPIO_PUEN (1<<8) + +#define GPIO_PF (0<<9) +#define GPIO_AF (1<<9) + +#define GPIO_OCR_MASK (3<<10) +#define GPIO_AIN (0<<10) +#define GPIO_BIN (1<<10) +#define GPIO_CIN (2<<10) +#define GPIO_GPIO (3<<10) + +#define GPIO_AOUT (1<<12) +#define GPIO_BOUT (1<<13) + +/* assignements for GPIO alternate/primary functions */ + +/* FIXME: This list is not completed. The correct directions are + * missing on some (many) pins + */ +#define PA0_PF_A24 ( GPIO_PORTA | GPIO_PF | 0 ) +#define PA0_AIN_SPI2_CLK ( GPIO_PORTA | GPIO_OUT | GPIO_AIN | 0 ) +#define PA0_AF_ETMTRACESYNC ( GPIO_PORTA | GPIO_AF | 0 ) +#define PA1_AOUT_SPI2_RXD ( GPIO_PORTA | GPIO_IN | GPIO_AOUT | 1 ) +#define PA1_PF_TIN ( GPIO_PORTA | GPIO_PF | 1 ) +#define PA2_PF_PWM0 ( GPIO_PORTA | GPIO_OUT | GPIO_PF | 2 ) +#define PA3_PF_CSI_MCLK ( GPIO_PORTA | GPIO_PF | 3 ) +#define PA4_PF_CSI_D0 ( GPIO_PORTA | GPIO_PF | 4 ) +#define PA5_PF_CSI_D1 ( GPIO_PORTA | GPIO_PF | 5 ) +#define PA6_PF_CSI_D2 ( GPIO_PORTA | GPIO_PF | 6 ) +#define PA7_PF_CSI_D3 ( GPIO_PORTA | GPIO_PF | 7 ) +#define PA8_PF_CSI_D4 ( GPIO_PORTA | GPIO_PF | 8 ) +#define PA9_PF_CSI_D5 ( GPIO_PORTA | GPIO_PF | 9 ) +#define PA10_PF_CSI_D6 ( GPIO_PORTA | GPIO_PF | 10 ) +#define PA11_PF_CSI_D7 ( GPIO_PORTA | GPIO_PF | 11 ) +#define PA12_PF_CSI_VSYNC ( GPIO_PORTA | GPIO_PF | 12 ) +#define PA13_PF_CSI_HSYNC ( GPIO_PORTA | GPIO_PF | 13 ) +#define PA14_PF_CSI_PIXCLK ( GPIO_PORTA | GPIO_PF | 14 ) +#define PA15_PF_I2C_SDA ( GPIO_PORTA | GPIO_OUT | GPIO_PF | 15 ) +#define PA16_PF_I2C_SCL ( GPIO_PORTA | GPIO_OUT | GPIO_PF | 16 ) +#define PA17_AF_ETMTRACEPKT4 ( GPIO_PORTA | GPIO_AF | 17 ) +#define PA17_AIN_SPI2_SS ( GPIO_PORTA | GPIO_AIN | 17 ) +#define PA18_AF_ETMTRACEPKT5 ( GPIO_PORTA | GPIO_AF | 18 ) +#define PA19_AF_ETMTRACEPKT6 ( GPIO_PORTA | GPIO_AF | 19 ) +#define PA20_AF_ETMTRACEPKT7 ( GPIO_PORTA | GPIO_AF | 20 ) +#define PA21_PF_A0 ( GPIO_PORTA | GPIO_PF | 21 ) +#define PA22_PF_CS4 ( GPIO_PORTA | GPIO_PF | 22 ) +#define PA23_PF_CS5 ( GPIO_PORTA | GPIO_PF | 23 ) +#define PA24_PF_A16 ( GPIO_PORTA | GPIO_PF | 24 ) +#define PA24_AF_ETMTRACEPKT0 ( GPIO_PORTA | GPIO_AF | 24 ) +#define PA25_PF_A17 ( GPIO_PORTA | GPIO_PF | 25 ) +#define PA25_AF_ETMTRACEPKT1 ( GPIO_PORTA | GPIO_AF | 25 ) +#define PA26_PF_A18 ( GPIO_PORTA | GPIO_PF | 26 ) +#define PA26_AF_ETMTRACEPKT2 ( GPIO_PORTA | GPIO_AF | 26 ) +#define PA27_PF_A19 ( GPIO_PORTA | GPIO_PF | 27 ) +#define PA27_AF_ETMTRACEPKT3 ( GPIO_PORTA | GPIO_AF | 27 ) +#define PA28_PF_A20 ( GPIO_PORTA | GPIO_PF | 28 ) +#define PA28_AF_ETMPIPESTAT0 ( GPIO_PORTA | GPIO_AF | 28 ) +#define PA29_PF_A21 ( GPIO_PORTA | GPIO_PF | 29 ) +#define PA29_AF_ETMPIPESTAT1 ( GPIO_PORTA | GPIO_AF | 29 ) +#define PA30_PF_A22 ( GPIO_PORTA | GPIO_PF | 30 ) +#define PA30_AF_ETMPIPESTAT2 ( GPIO_PORTA | GPIO_AF | 30 ) +#define PA31_PF_A23 ( GPIO_PORTA | GPIO_PF | 31 ) +#define PA31_AF_ETMTRACECLK ( GPIO_PORTA | GPIO_AF | 31 ) +#define PB8_PF_SD_DAT0 ( GPIO_PORTB | GPIO_PF | GPIO_PUEN | 8 ) +#define PB8_AF_MS_PIO ( GPIO_PORTB | GPIO_AF | 8 ) +#define PB9_PF_SD_DAT1 ( GPIO_PORTB | GPIO_PF | GPIO_PUEN | 9 ) +#define PB9_AF_MS_PI1 ( GPIO_PORTB | GPIO_AF | 9 ) +#define PB10_PF_SD_DAT2 ( GPIO_PORTB | GPIO_PF | GPIO_PUEN | 10 ) +#define PB10_AF_MS_SCLKI ( GPIO_PORTB | GPIO_AF | 10 ) +#define PB11_PF_SD_DAT3 ( GPIO_PORTB | GPIO_PF | GPIO_PUEN | 11 ) +#define PB11_AF_MS_SDIO ( GPIO_PORTB | GPIO_AF | 11 ) +#define PB12_PF_SD_CLK ( GPIO_PORTB | GPIO_PF | GPIO_OUT | 12 ) +#define PB12_AF_MS_SCLK0 ( GPIO_PORTB | GPIO_AF | 12 ) +#define PB13_PF_SD_CMD ( GPIO_PORTB | GPIO_PF | GPIO_OUT | GPIO_PUEN | 13 ) +#define PB13_AF_MS_BS ( GPIO_PORTB | GPIO_AF | 13 ) +#define PB14_AF_SSI_RXFS ( GPIO_PORTB | GPIO_AF | 14 ) +#define PB15_AF_SSI_RXCLK ( GPIO_PORTB | GPIO_AF | 15 ) +#define PB16_AF_SSI_RXDAT ( GPIO_PORTB | GPIO_IN | GPIO_AF | 16 ) +#define PB17_AF_SSI_TXDAT ( GPIO_PORTB | GPIO_OUT | GPIO_AF | 17 ) +#define PB18_AF_SSI_TXFS ( GPIO_PORTB | GPIO_AF | 18 ) +#define PB19_AF_SSI_TXCLK ( GPIO_PORTB | GPIO_AF | 19 ) +#define PB20_PF_USBD_AFE ( GPIO_PORTB | GPIO_PF | 20 ) +#define PB21_PF_USBD_OE ( GPIO_PORTB | GPIO_PF | 21 ) +#define PB22_PFUSBD_RCV ( GPIO_PORTB | GPIO_PF | 22 ) +#define PB23_PF_USBD_SUSPND ( GPIO_PORTB | GPIO_PF | 23 ) +#define PB24_PF_USBD_VP ( GPIO_PORTB | GPIO_PF | 24 ) +#define PB25_PF_USBD_VM ( GPIO_PORTB | GPIO_PF | 25 ) +#define PB26_PF_USBD_VPO ( GPIO_PORTB | GPIO_PF | 26 ) +#define PB27_PF_USBD_VMO ( GPIO_PORTB | GPIO_PF | 27 ) +#define PB28_PF_UART2_CTS ( GPIO_PORTB | GPIO_OUT | GPIO_PF | 28 ) +#define PB29_PF_UART2_RTS ( GPIO_PORTB | GPIO_IN | GPIO_PF | 29 ) +#define PB30_PF_UART2_TXD ( GPIO_PORTB | GPIO_OUT | GPIO_PF | 30 ) +#define PB31_PF_UART2_RXD ( GPIO_PORTB | GPIO_IN | GPIO_PF | 31 ) +#define PC3_PF_SSI_RXFS ( GPIO_PORTC | GPIO_PF | 3 ) +#define PC4_PF_SSI_RXCLK ( GPIO_PORTC | GPIO_PF | 4 ) +#define PC5_PF_SSI_RXDAT ( GPIO_PORTC | GPIO_IN | GPIO_PF | 5 ) +#define PC6_PF_SSI_TXDAT ( GPIO_PORTC | GPIO_OUT | GPIO_PF | 6 ) +#define PC7_PF_SSI_TXFS ( GPIO_PORTC | GPIO_PF | 7 ) +#define PC8_PF_SSI_TXCLK ( GPIO_PORTC | GPIO_PF | 8 ) +#define PC9_PF_UART1_CTS ( GPIO_PORTC | GPIO_OUT | GPIO_PF | 9 ) +#define PC10_PF_UART1_RTS ( GPIO_PORTC | GPIO_IN | GPIO_PF | 10 ) +#define PC11_PF_UART1_TXD ( GPIO_PORTC | GPIO_OUT | GPIO_PF | 11 ) +#define PC12_PF_UART1_RXD ( GPIO_PORTC | GPIO_IN | GPIO_PF | 12 ) +#define PC13_PF_SPI1_SPI_RDY ( GPIO_PORTC | GPIO_PF | 13 ) +#define PC14_PF_SPI1_SCLK ( GPIO_PORTC | GPIO_PF | 14 ) +#define PC15_PF_SPI1_SS ( GPIO_PORTC | GPIO_PF | 15 ) +#define PC16_PF_SPI1_MISO ( GPIO_PORTC | GPIO_PF | 16 ) +#define PC17_PF_SPI1_MOSI ( GPIO_PORTC | GPIO_PF | 17 ) +#define PD6_PF_LSCLK ( GPIO_PORTD | GPIO_OUT | GPIO_PF | 6 ) +#define PD7_PF_REV ( GPIO_PORTD | GPIO_PF | 7 ) +#define PD7_AF_UART2_DTR ( GPIO_PORTD | GPIO_IN | GPIO_AF | 7 ) +#define PD7_AIN_SPI2_SCLK ( GPIO_PORTD | GPIO_AIN | 7 ) +#define PD8_PF_CLS ( GPIO_PORTD | GPIO_PF | 8 ) +#define PD8_AF_UART2_DCD ( GPIO_PORTD | GPIO_OUT | GPIO_AF | 8 ) +#define PD8_AIN_SPI2_SS ( GPIO_PORTD | GPIO_AIN | 8 ) +#define PD9_PF_PS ( GPIO_PORTD | GPIO_PF | 9 ) +#define PD9_AF_UART2_RI ( GPIO_PORTD | GPIO_OUT | GPIO_AF | 9 ) +#define PD9_AOUT_SPI2_RXD ( GPIO_PORTD | GPIO_IN | GPIO_AOUT | 9 ) +#define PD10_PF_SPL_SPR ( GPIO_PORTD | GPIO_OUT | GPIO_PF | 10 ) +#define PD10_AF_UART2_DSR ( GPIO_PORTD | GPIO_OUT | GPIO_AF | 10 ) +#define PD10_AIN_SPI2_TXD ( GPIO_PORTD | GPIO_OUT | GPIO_AIN | 10 ) +#define PD11_PF_CONTRAST ( GPIO_PORTD | GPIO_OUT | GPIO_PF | 11 ) +#define PD12_PF_ACD_OE ( GPIO_PORTD | GPIO_OUT | GPIO_PF | 12 ) +#define PD13_PF_LP_HSYNC ( GPIO_PORTD | GPIO_OUT | GPIO_PF | 13 ) +#define PD14_PF_FLM_VSYNC ( GPIO_PORTD | GPIO_OUT | GPIO_PF | 14 ) +#define PD15_PF_LD0 ( GPIO_PORTD | GPIO_OUT | GPIO_PF | 15 ) +#define PD16_PF_LD1 ( GPIO_PORTD | GPIO_OUT | GPIO_PF | 16 ) +#define PD17_PF_LD2 ( GPIO_PORTD | GPIO_OUT | GPIO_PF | 17 ) +#define PD18_PF_LD3 ( GPIO_PORTD | GPIO_OUT | GPIO_PF | 18 ) +#define PD19_PF_LD4 ( GPIO_PORTD | GPIO_OUT | GPIO_PF | 19 ) +#define PD20_PF_LD5 ( GPIO_PORTD | GPIO_OUT | GPIO_PF | 20 ) +#define PD21_PF_LD6 ( GPIO_PORTD | GPIO_OUT | GPIO_PF | 21 ) +#define PD22_PF_LD7 ( GPIO_PORTD | GPIO_OUT | GPIO_PF | 22 ) +#define PD23_PF_LD8 ( GPIO_PORTD | GPIO_OUT | GPIO_PF | 23 ) +#define PD24_PF_LD9 ( GPIO_PORTD | GPIO_OUT | GPIO_PF | 24 ) +#define PD25_PF_LD10 ( GPIO_PORTD | GPIO_OUT | GPIO_PF | 25 ) +#define PD26_PF_LD11 ( GPIO_PORTD | GPIO_OUT | GPIO_PF | 26 ) +#define PD27_PF_LD12 ( GPIO_PORTD | GPIO_OUT | GPIO_PF | 27 ) +#define PD28_PF_LD13 ( GPIO_PORTD | GPIO_OUT | GPIO_PF | 28 ) +#define PD29_PF_LD14 ( GPIO_PORTD | GPIO_OUT | GPIO_PF | 29 ) +#define PD30_PF_LD15 ( GPIO_PORTD | GPIO_OUT | GPIO_PF | 30 ) +#define PD31_PF_TMR2OUT ( GPIO_PORTD | GPIO_PF | 31 ) +#define PD31_BIN_SPI2_TXD ( GPIO_PORTD | GPIO_BIN | 31 ) + +/* + * DMA Controller + */ +#define DCR __REG(IMX_DMAC_BASE +0x00) /* DMA Control Register */ +#define DISR __REG(IMX_DMAC_BASE +0x04) /* DMA Interrupt status Register */ +#define DIMR __REG(IMX_DMAC_BASE +0x08) /* DMA Interrupt mask Register */ +#define DBTOSR __REG(IMX_DMAC_BASE +0x0c) /* DMA Burst timeout status Register */ +#define DRTOSR __REG(IMX_DMAC_BASE +0x10) /* DMA Request timeout Register */ +#define DSESR __REG(IMX_DMAC_BASE +0x14) /* DMA Transfer Error Status Register */ +#define DBOSR __REG(IMX_DMAC_BASE +0x18) /* DMA Buffer overflow status Register */ +#define DBTOCR __REG(IMX_DMAC_BASE +0x1c) /* DMA Burst timeout control Register */ +#define WSRA __REG(IMX_DMAC_BASE +0x40) /* W-Size Register A */ +#define XSRA __REG(IMX_DMAC_BASE +0x44) /* X-Size Register A */ +#define YSRA __REG(IMX_DMAC_BASE +0x48) /* Y-Size Register A */ +#define WSRB __REG(IMX_DMAC_BASE +0x4c) /* W-Size Register B */ +#define XSRB __REG(IMX_DMAC_BASE +0x50) /* X-Size Register B */ +#define YSRB __REG(IMX_DMAC_BASE +0x54) /* Y-Size Register B */ +#define SAR(x) __REG2( IMX_DMAC_BASE + 0x80, (x) << 6) /* Source Address Registers */ +#define DAR(x) __REG2( IMX_DMAC_BASE + 0x84, (x) << 6) /* Destination Address Registers */ +#define CNTR(x) __REG2( IMX_DMAC_BASE + 0x88, (x) << 6) /* Count Registers */ +#define CCR(x) __REG2( IMX_DMAC_BASE + 0x8c, (x) << 6) /* Control Registers */ +#define RSSR(x) __REG2( IMX_DMAC_BASE + 0x90, (x) << 6) /* Request source select Registers */ +#define BLR(x) __REG2( IMX_DMAC_BASE + 0x94, (x) << 6) /* Burst length Registers */ +#define RTOR(x) __REG2( IMX_DMAC_BASE + 0x98, (x) << 6) /* Request timeout Registers */ +#define BUCR(x) __REG2( IMX_DMAC_BASE + 0x98, (x) << 6) /* Bus Utilization Registers */ + +/* TODO: define DMA_REQ lines */ + +#define DCR_DRST (1<<1) +#define DCR_DEN (1<<0) +#define DBTOCR_EN (1<<15) +#define DBTOCR_CNT(x) ((x) & 0x7fff ) +#define CNTR_CNT(x) ((x) & 0xffffff ) +#define CCR_DMOD_LINEAR ( 0x0 << 12 ) +#define CCR_DMOD_2D ( 0x1 << 12 ) +#define CCR_DMOD_FIFO ( 0x2 << 12 ) +#define CCR_DMOD_EOBFIFO ( 0x3 << 12 ) +#define CCR_SMOD_LINEAR ( 0x0 << 10 ) +#define CCR_SMOD_2D ( 0x1 << 10 ) +#define CCR_SMOD_FIFO ( 0x2 << 10 ) +#define CCR_SMOD_EOBFIFO ( 0x3 << 10 ) +#define CCR_MDIR_DEC (1<<9) +#define CCR_MSEL_B (1<<8) +#define CCR_DSIZ_32 ( 0x0 << 6 ) +#define CCR_DSIZ_8 ( 0x1 << 6 ) +#define CCR_DSIZ_16 ( 0x2 << 6 ) +#define CCR_SSIZ_32 ( 0x0 << 4 ) +#define CCR_SSIZ_8 ( 0x1 << 4 ) +#define CCR_SSIZ_16 ( 0x2 << 4 ) +#define CCR_REN (1<<3) +#define CCR_RPT (1<<2) +#define CCR_FRC (1<<1) +#define CCR_CEN (1<<0) +#define RTOR_EN (1<<15) +#define RTOR_CLK (1<<14) +#define RTOR_PSC (1<<13) + +/* + * LCD Controller + */ + +#define LCDC_SSA __REG(IMX_LCDC_BASE+0x00) + +#define LCDC_SIZE __REG(IMX_LCDC_BASE+0x04) +#define SIZE_XMAX(x) ((((x) >> 4) & 0x3f) << 20) +#define SIZE_YMAX(y) ( (y) & 0x1ff ) + +#define LCDC_VPW __REG(IMX_LCDC_BASE+0x08) +#define VPW_VPW(x) ( (x) & 0x3ff ) + +#define LCDC_CPOS __REG(IMX_LCDC_BASE+0x0C) +#define CPOS_CC1 (1<<31) +#define CPOS_CC0 (1<<30) +#define CPOS_OP (1<<28) +#define CPOS_CXP(x) (((x) & 3ff) << 16) +#define CPOS_CYP(y) ((y) & 0x1ff) + +#define LCDC_LCWHB __REG(IMX_LCDC_BASE+0x10) +#define LCWHB_BK_EN (1<<31) +#define LCWHB_CW(w) (((w) & 0x1f) << 24) +#define LCWHB_CH(h) (((h) & 0x1f) << 16) +#define LCWHB_BD(x) ((x) & 0xff) + +#define LCDC_LCHCC __REG(IMX_LCDC_BASE+0x14) +#define LCHCC_CUR_COL_R(r) (((r) & 0x1f) << 11) +#define LCHCC_CUR_COL_G(g) (((g) & 0x3f) << 5) +#define LCHCC_CUR_COL_B(b) ((b) & 0x1f) + +#define LCDC_PCR __REG(IMX_LCDC_BASE+0x18) +#define PCR_TFT (1<<31) +#define PCR_COLOR (1<<30) +#define PCR_PBSIZ_1 (0<<28) +#define PCR_PBSIZ_2 (1<<28) +#define PCR_PBSIZ_4 (2<<28) +#define PCR_PBSIZ_8 (3<<28) +#define PCR_BPIX_1 (0<<25) +#define PCR_BPIX_2 (1<<25) +#define PCR_BPIX_4 (2<<25) +#define PCR_BPIX_8 (3<<25) +#define PCR_BPIX_12 (4<<25) +#define PCR_BPIX_16 (4<<25) +#define PCR_PIXPOL (1<<24) +#define PCR_FLMPOL (1<<23) +#define PCR_LPPOL (1<<22) +#define PCR_CLKPOL (1<<21) +#define PCR_OEPOL (1<<20) +#define PCR_SCLKIDLE (1<<19) +#define PCR_END_SEL (1<<18) +#define PCR_END_BYTE_SWAP (1<<17) +#define PCR_REV_VS (1<<16) +#define PCR_ACD_SEL (1<<15) +#define PCR_ACD(x) (((x) & 0x7f) << 8) +#define PCR_SCLK_SEL (1<<7) +#define PCR_SHARP (1<<6) +#define PCR_PCD(x) ((x) & 0x3f) + +#define LCDC_HCR __REG(IMX_LCDC_BASE+0x1C) +#define HCR_H_WIDTH(x) (((x) & 0x3f) << 26) +#define HCR_H_WAIT_1(x) (((x) & 0xff) << 8) +#define HCR_H_WAIT_2(x) ((x) & 0xff) + +#define LCDC_VCR __REG(IMX_LCDC_BASE+0x20) +#define VCR_V_WIDTH(x) (((x) & 0x3f) << 26) +#define VCR_V_WAIT_1(x) (((x) & 0xff) << 8) +#define VCR_V_WAIT_2(x) ((x) & 0xff) + +#define LCDC_POS __REG(IMX_LCDC_BASE+0x24) +#define POS_POS(x) ((x) & 1f) + +#define LCDC_LSCR1 __REG(IMX_LCDC_BASE+0x28) +#define LSCR1_GRAY1(x) (((x) & 0xf) << 4) +#define LSCR1_GRAY2(x) ((x) & 0xf) + +#define LCDC_PWMR __REG(IMX_LCDC_BASE+0x2C) +#define PWMR_CLS(x) (((x) & 0x1ff) << 16) +#define PWMR_LDMSK (1<<15) +#define PWMR_SCR1 (1<<10) +#define PWMR_SCR0 (1<<9) +#define PWMR_CC_EN (1<<8) +#define PWMR_PW(x) ((x) & 0xff) + +#define LCDC_DMACR __REG(IMX_LCDC_BASE+0x30) +#define DMACR_BURST (1<<31) +#define DMACR_HM(x) (((x) & 0xf) << 16) +#define DMACR_TM(x) ((x) &0xf) + +#define LCDC_RMCR __REG(IMX_LCDC_BASE+0x34) +#define RMCR_LCDC_EN (1<<1) +#define RMCR_SELF_REF (1<<0) + +#define LCDC_LCDICR __REG(IMX_LCDC_BASE+0x38) +#define LCDICR_INT_SYN (1<<2) +#define LCDICR_INT_CON (1) + +#define LCDC_LCDISR __REG(IMX_LCDC_BASE+0x40) +#define LCDISR_UDR_ERR (1<<3) +#define LCDISR_ERR_RES (1<<2) +#define LCDISR_EOF (1<<1) +#define LCDISR_BOF (1<<0) +/* + * UART Module + */ +#define URXD0(x) __REG2( IMX_UART1_BASE + 0x0, ((x) & 1) << 12) /* Receiver Register */ +#define URTX0(x) __REG2( IMX_UART1_BASE + 0x40, ((x) & 1) << 12) /* Transmitter Register */ +#define UCR1(x) __REG2( IMX_UART1_BASE + 0x80, ((x) & 1) << 12) /* Control Register 1 */ +#define UCR2(x) __REG2( IMX_UART1_BASE + 0x84, ((x) & 1) << 12) /* Control Register 2 */ +#define UCR3(x) __REG2( IMX_UART1_BASE + 0x88, ((x) & 1) << 12) /* Control Register 3 */ +#define UCR4(x) __REG2( IMX_UART1_BASE + 0x8c, ((x) & 1) << 12) /* Control Register 4 */ +#define UFCR(x) __REG2( IMX_UART1_BASE + 0x90, ((x) & 1) << 12) /* FIFO Control Register */ +#define USR1(x) __REG2( IMX_UART1_BASE + 0x94, ((x) & 1) << 12) /* Status Register 1 */ +#define USR2(x) __REG2( IMX_UART1_BASE + 0x98, ((x) & 1) << 12) /* Status Register 2 */ +#define UESC(x) __REG2( IMX_UART1_BASE + 0x9c, ((x) & 1) << 12) /* Escape Character Register */ +#define UTIM(x) __REG2( IMX_UART1_BASE + 0xa0, ((x) & 1) << 12) /* Escape Timer Register */ +#define UBIR(x) __REG2( IMX_UART1_BASE + 0xa4, ((x) & 1) << 12) /* BRM Incremental Register */ +#define UBMR(x) __REG2( IMX_UART1_BASE + 0xa8, ((x) & 1) << 12) /* BRM Modulator Register */ +#define UBRC(x) __REG2( IMX_UART1_BASE + 0xac, ((x) & 1) << 12) /* Baud Rate Count Register */ +#define BIPR1(x) __REG2( IMX_UART1_BASE + 0xb0, ((x) & 1) << 12) /* Incremental Preset Register 1 */ +#define BIPR2(x) __REG2( IMX_UART1_BASE + 0xb4, ((x) & 1) << 12) /* Incremental Preset Register 2 */ +#define BIPR3(x) __REG2( IMX_UART1_BASE + 0xb8, ((x) & 1) << 12) /* Incremental Preset Register 3 */ +#define BIPR4(x) __REG2( IMX_UART1_BASE + 0xbc, ((x) & 1) << 12) /* Incremental Preset Register 4 */ +#define BMPR1(x) __REG2( IMX_UART1_BASE + 0xc0, ((x) & 1) << 12) /* BRM Modulator Register 1 */ +#define BMPR2(x) __REG2( IMX_UART1_BASE + 0xc4, ((x) & 1) << 12) /* BRM Modulator Register 2 */ +#define BMPR3(x) __REG2( IMX_UART1_BASE + 0xc8, ((x) & 1) << 12) /* BRM Modulator Register 3 */ +#define BMPR4(x) __REG2( IMX_UART1_BASE + 0xcc, ((x) & 1) << 12) /* BRM Modulator Register 4 */ +#define UTS(x) __REG2( IMX_UART1_BASE + 0xd0, ((x) & 1) << 12) /* UART Test Register */ + +/* UART Control Register Bit Fields.*/ +#define URXD_CHARRDY (1<<15) +#define URXD_ERR (1<<14) +#define URXD_OVRRUN (1<<13) +#define URXD_FRMERR (1<<12) +#define URXD_BRK (1<<11) +#define URXD_PRERR (1<<10) +#define UCR1_ADEN (1<<15) /* Auto dectect interrupt */ +#define UCR1_ADBR (1<<14) /* Auto detect baud rate */ +#define UCR1_TRDYEN (1<<13) /* Transmitter ready interrupt enable */ +#define UCR1_IDEN (1<<12) /* Idle condition interrupt */ +#define UCR1_RRDYEN (1<<9) /* Recv ready interrupt enable */ +#define UCR1_RDMAEN (1<<8) /* Recv ready DMA enable */ +#define UCR1_IREN (1<<7) /* Infrared interface enable */ +#define UCR1_TXMPTYEN (1<<6) /* Transimitter empty interrupt enable */ +#define UCR1_RTSDEN (1<<5) /* RTS delta interrupt enable */ +#define UCR1_SNDBRK (1<<4) /* Send break */ +#define UCR1_TDMAEN (1<<3) /* Transmitter ready DMA enable */ +#define UCR1_UARTCLKEN (1<<2) /* UART clock enabled */ +#define UCR1_DOZE (1<<1) /* Doze */ +#define UCR1_UARTEN (1<<0) /* UART enabled */ +#define UCR2_ESCI (1<<15) /* Escape seq interrupt enable */ +#define UCR2_IRTS (1<<14) /* Ignore RTS pin */ +#define UCR2_CTSC (1<<13) /* CTS pin control */ +#define UCR2_CTS (1<<12) /* Clear to send */ +#define UCR2_ESCEN (1<<11) /* Escape enable */ +#define UCR2_PREN (1<<8) /* Parity enable */ +#define UCR2_PROE (1<<7) /* Parity odd/even */ +#define UCR2_STPB (1<<6) /* Stop */ +#define UCR2_WS (1<<5) /* Word size */ +#define UCR2_RTSEN (1<<4) /* Request to send interrupt enable */ +#define UCR2_TXEN (1<<2) /* Transmitter enabled */ +#define UCR2_RXEN (1<<1) /* Receiver enabled */ +#define UCR2_SRST (1<<0) /* SW reset */ +#define UCR3_DTREN (1<<13) /* DTR interrupt enable */ +#define UCR3_PARERREN (1<<12) /* Parity enable */ +#define UCR3_FRAERREN (1<<11) /* Frame error interrupt enable */ +#define UCR3_DSR (1<<10) /* Data set ready */ +#define UCR3_DCD (1<<9) /* Data carrier detect */ +#define UCR3_RI (1<<8) /* Ring indicator */ +#define UCR3_TIMEOUTEN (1<<7) /* Timeout interrupt enable */ +#define UCR3_RXDSEN (1<<6) /* Receive status interrupt enable */ +#define UCR3_AIRINTEN (1<<5) /* Async IR wake interrupt enable */ +#define UCR3_AWAKEN (1<<4) /* Async wake interrupt enable */ +#define UCR3_REF25 (1<<3) /* Ref freq 25 MHz */ +#define UCR3_REF30 (1<<2) /* Ref Freq 30 MHz */ +#define UCR3_INVT (1<<1) /* Inverted Infrared transmission */ +#define UCR3_BPEN (1<<0) /* Preset registers enable */ +#define UCR4_CTSTL_32 (32<<10) /* CTS trigger level (32 chars) */ +#define UCR4_INVR (1<<9) /* Inverted infrared reception */ +#define UCR4_ENIRI (1<<8) /* Serial infrared interrupt enable */ +#define UCR4_WKEN (1<<7) /* Wake interrupt enable */ +#define UCR4_REF16 (1<<6) /* Ref freq 16 MHz */ +#define UCR4_IRSC (1<<5) /* IR special case */ +#define UCR4_TCEN (1<<3) /* Transmit complete interrupt enable */ +#define UCR4_BKEN (1<<2) /* Break condition interrupt enable */ +#define UCR4_OREN (1<<1) /* Receiver overrun interrupt enable */ +#define UCR4_DREN (1<<0) /* Recv data ready interrupt enable */ +#define UFCR_RXTL_SHF 0 /* Receiver trigger level shift */ +#define UFCR_RFDIV (7<<7) /* Reference freq divider mask */ +#define UFCR_TXTL_SHF 10 /* Transmitter trigger level shift */ +#define USR1_PARITYERR (1<<15) /* Parity error interrupt flag */ +#define USR1_RTSS (1<<14) /* RTS pin status */ +#define USR1_TRDY (1<<13) /* Transmitter ready interrupt/dma flag */ +#define USR1_RTSD (1<<12) /* RTS delta */ +#define USR1_ESCF (1<<11) /* Escape seq interrupt flag */ +#define USR1_FRAMERR (1<<10) /* Frame error interrupt flag */ +#define USR1_RRDY (1<<9) /* Receiver ready interrupt/dma flag */ +#define USR1_TIMEOUT (1<<7) /* Receive timeout interrupt status */ +#define USR1_RXDS (1<<6) /* Receiver idle interrupt flag */ +#define USR1_AIRINT (1<<5) /* Async IR wake interrupt flag */ +#define USR1_AWAKE (1<<4) /* Aysnc wake interrupt flag */ +#define USR2_ADET (1<<15) /* Auto baud rate detect complete */ +#define USR2_TXFE (1<<14) /* Transmit buffer FIFO empty */ +#define USR2_DTRF (1<<13) /* DTR edge interrupt flag */ +#define USR2_IDLE (1<<12) /* Idle condition */ +#define USR2_IRINT (1<<8) /* Serial infrared interrupt flag */ +#define USR2_WAKE (1<<7) /* Wake */ +#define USR2_RTSF (1<<4) /* RTS edge interrupt flag */ +#define USR2_TXDC (1<<3) /* Transmitter complete */ +#define USR2_BRCD (1<<2) /* Break condition */ +#define USR2_ORE (1<<1) /* Overrun error */ +#define USR2_RDR (1<<0) /* Recv data ready */ +#define UTS_FRCPERR (1<<13) /* Force parity error */ +#define UTS_LOOP (1<<12) /* Loop tx and rx */ +#define UTS_TXEMPTY (1<<6) /* TxFIFO empty */ +#define UTS_RXEMPTY (1<<5) /* RxFIFO empty */ +#define UTS_TXFULL (1<<4) /* TxFIFO full */ +#define UTS_RXFULL (1<<3) /* RxFIFO full */ +#define UTS_SOFTRST (1<<0) /* Software reset */ + +/* General purpose timers registers */ +#define TCTL1 __REG(IMX_TIM1_BASE) +#define TPRER1 __REG(IMX_TIM1_BASE + 0x4) +#define TCMP1 __REG(IMX_TIM1_BASE + 0x8) +#define TCR1 __REG(IMX_TIM1_BASE + 0xc) +#define TCN1 __REG(IMX_TIM1_BASE + 0x10) +#define TSTAT1 __REG(IMX_TIM1_BASE + 0x14) +#define TCTL2 __REG(IMX_TIM2_BASE) +#define TPRER2 __REG(IMX_TIM2_BASE + 0x4) +#define TCMP2 __REG(IMX_TIM2_BASE + 0x8) +#define TCR2 __REG(IMX_TIM2_BASE + 0xc) +#define TCN2 __REG(IMX_TIM2_BASE + 0x10) +#define TSTAT2 __REG(IMX_TIM2_BASE + 0x14) + +/* General purpose timers bitfields */ +#define TCTL_SWR (1<<15) /* Software reset */ +#define TCTL_FRR (1<<8) /* Freerun / restart */ +#define TCTL_CAP (3<<6) /* Capture Edge */ +#define TCTL_OM (1<<5) /* output mode */ +#define TCTL_IRQEN (1<<4) /* interrupt enable */ +#define TCTL_CLKSOURCE (7<<1) /* Clock source */ +#define TCTL_TEN (1) /* Timer enable */ +#define TPRER_PRES (0xff) /* Prescale */ +#define TSTAT_CAPT (1<<1) /* Capture event */ +#define TSTAT_COMP (1) /* Compare event */ + +#endif /* _IMX_REGS_H */ diff --git a/include/common.h b/include/common.h index 02efba3c7a..48e38b965d 100644 --- a/include/common.h +++ b/include/common.h @@ -126,6 +126,17 @@ typedef void (interrupt_handler_t)(void *); # endif #endif +#ifndef CONFIG_SERIAL_MULTI + +#if defined(CONFIG_8xx_CONS_SMC1) || defined(CONFIG_8xx_CONS_SMC2) \ + || defined(CONFIG_8xx_CONS_SCC1) || defined(CONFIG_8xx_CONS_SCC2) \ + || defined(CONFIG_8xx_CONS_SCC3) || defined(CONFIG_8xx_CONS_SCC4) + +#define CONFIG_SERIAL_MULTI 1 + +#endif + +#endif /* CONFIG_SERIAL_MULTI */ /* * General Purpose Utilities @@ -403,6 +414,15 @@ ulong get_PLLCLK (void); #if defined CONFIG_INCA_IP uint incaip_get_cpuclk (void); #endif +#if defined(CONFIG_IMX) +ulong get_systemPLLCLK(void); +ulong get_FCLK(void); +ulong get_HCLK(void); +ulong get_BCLK(void); +ulong get_PERCLK1(void); +ulong get_PERCLK2(void); +ulong get_PERCLK3(void); +#endif ulong get_bus_freq (ulong); #if defined(CONFIG_MPC85xx) diff --git a/include/commproc.h b/include/commproc.h index f87620ebf1..83119717a9 100644 --- a/include/commproc.h +++ b/include/commproc.h @@ -74,9 +74,10 @@ #define CPM_I2C_BASE 0x0820 #define CPM_SPI_BASE 0x0840 #define CPM_FEC_BASE 0x0860 -#define CPM_WLKBD_BASE 0x0880 +#define CPM_SERIAL2_BASE 0x0880 #define CPM_SCC_BASE 0x0900 #define CPM_POST_BASE 0x0980 +#define CPM_WLKBD_BASE 0x0a00 #endif @@ -1041,7 +1042,7 @@ typedef struct scc_enet { /*** LWMON **********************************************************/ -#if defined(CONFIG_LWMON) && !defined(CONFIG_8xx_CONS_SCC2) +#if defined(CONFIG_LWMON) /* Bits in parallel I/O port registers that have to be set/cleared * to configure the pins for SCC2 use. */ diff --git a/include/configs/PPChameleonEVB.h b/include/configs/PPChameleonEVB.h index bb8ce43bab..b1f41a1727 100644 --- a/include/configs/PPChameleonEVB.h +++ b/include/configs/PPChameleonEVB.h @@ -43,6 +43,9 @@ * CONFIG_PPCHAMELEON_CLK_25 * CONFIG_PPCHAMELEON_CLK_33 */ +#if (!defined(CONFIG_PPCHAMELEON_CLK_25) && !defined(CONFIG_PPCHAMELEON_CLK_33)) +#define CONFIG_PPCHAMELEON_CLK_33 +#endif #if (defined(CONFIG_PPCHAMELEON_CLK_25) && defined(CONFIG_PPCHAMELEON_CLK_33)) #error "* Two external frequencies (SysClk) are defined! *" @@ -74,11 +77,11 @@ #ifdef CONFIG_PPCHAMELEON_CLK_25 - #define CONFIG_SYS_CLK_FREQ 25000000 /* external frequency to pll */ +# define CONFIG_SYS_CLK_FREQ 25000000 /* external frequency to pll */ #elif (defined (CONFIG_PPCHAMELEON_CLK_33)) -#define CONFIG_SYS_CLK_FREQ 33333333 /* external frequency to pll */ +# define CONFIG_SYS_CLK_FREQ 33333333 /* external frequency to pll */ #else -#error "* External frequency (SysClk) not defined! *" +# error "* External frequency (SysClk) not defined! *" #endif #define CONFIG_BAUDRATE 115200 diff --git a/include/configs/Total5200.h b/include/configs/Total5200.h index 830bf81a45..47f24be520 100644 --- a/include/configs/Total5200.h +++ b/include/configs/Total5200.h @@ -64,6 +64,7 @@ * Video console */ #if 1 +#define CONFIG_VIDEO #define CONFIG_VIDEO_SED13806 #define CONFIG_VIDEO_SED13806_16BPP diff --git a/include/configs/lwmon.h b/include/configs/lwmon.h index d944ed88cd..a76ec23652 100644 --- a/include/configs/lwmon.h +++ b/include/configs/lwmon.h @@ -47,11 +47,9 @@ #define CONFIG_SPLASH_SCREEN /* ... with splashscreen support*/ -#if 1 +#define CONFIG_SERIAL_MULTI 1 #define CONFIG_8xx_CONS_SMC2 1 /* Console is on SMC2 */ -#else -#define CONFIG_8xx_CONS_SCC2 -#endif +#define CONFIG_8xx_CONS_SCC2 1 /* Console is on SCC2 */ #define CONFIG_BAUDRATE 115200 /* with watchdog >= 38400 needed */ @@ -151,17 +149,6 @@ #define CFG_CMD_POST_DIAG 0 #endif -#ifdef CONFIG_8xx_CONS_SCC2 /* Can't use ethernet, then */ -#define CONFIG_COMMANDS ( (CONFIG_CMD_DFL & ~CFG_CMD_NET) | \ - CFG_CMD_ASKENV | \ - CFG_CMD_DATE | \ - CFG_CMD_I2C | \ - CFG_CMD_EEPROM | \ - CFG_CMD_IDE | \ - CFG_CMD_BSP | \ - CFG_CMD_BMP | \ - CFG_CMD_POST_DIAG ) -#else #define CONFIG_COMMANDS ( CONFIG_CMD_DFL | \ CFG_CMD_ASKENV | \ CFG_CMD_DHCP | \ @@ -172,7 +159,6 @@ CFG_CMD_BSP | \ CFG_CMD_BMP | \ CFG_CMD_POST_DIAG ) -#endif #define CONFIG_MAC_PARTITION #define CONFIG_DOS_PARTITION diff --git a/include/configs/mx1ads.h b/include/configs/mx1ads.h index 5cf092af55..df951e2d74 100644 --- a/include/configs/mx1ads.h +++ b/include/configs/mx1ads.h @@ -16,7 +16,7 @@ * * This program is distributed in the hope that it will be useful, * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. * * You should have received a copy of the GNU General Public License @@ -25,7 +25,6 @@ * MA 02111-1307 USA */ - #ifndef __CONFIG_H #define __CONFIG_H @@ -40,14 +39,19 @@ * (easy to change) */ #define CONFIG_ARM920T 1 /* This is an ARM920T Core */ -#define CONFIG_MC9328 1 /* It's a Motorola MC9328 SoC */ -#define CONFIG_MX1ADS 1 /* on a Motorola MX1ADS Board */ - -#define BOARD_LATE_INIT 1 +#define CONFIG_IMX 1 /* It's a Motorola MC9328 SoC */ +#define CONFIG_MX1ADS 1 /* on a Motorola MX1ADS Board */ +#undef CONFIG_USE_IRQ /* we don't need IRQ/FIQ stuff */ +/* + * Select serial console configuration + */ +#define CONFIG_IMX_SERIAL1 /* internal uart 1 */ +/* #define _CONFIG_UART2 */ /* internal uart 2 */ +/* #define CONFIG_SILENT_CONSOLE */ /* use this to disable output */ +#define BOARD_LATE_INIT 1 #define USE_920T_MMU 1 -#undef CONFIG_USE_IRQ /* we don't need IRQ/FIQ stuff */ #if 0 #define CFG_MX1_GPCR 0x000003AB /* for MX1ADS 0L44N */ @@ -60,6 +64,8 @@ */ #define CFG_MALLOC_LEN (CFG_ENV_SIZE + 128*1024) + + #define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */ /* @@ -67,13 +73,13 @@ */ #define CONFIG_DRIVER_CS8900 1 /* we have a CS8900 on-board */ #define CS8900_BASE 0x15000300 -#define CS8900_BUS16 1 /* the Linux driver does accesses as shorts */ +#define CS8900_BUS16 1 /* the Linux driver does accesses as shorts */ /* * select serial console configuration */ -#define CONFIG_UART1 1 +/* #define CONFIG_UART1 */ /* #define CONFIG_UART2 1 */ #define CONFIG_BAUDRATE 115200 @@ -85,24 +91,20 @@ #define CONFIG_COMMANDS \ (CONFIG_CMD_DFL | \ CFG_CMD_CACHE | \ - /*CFG_CMD_NAND |*/ \ - /*CFG_CMD_EEPROM |*/ \ - /*CFG_CMD_I2C |*/ \ - /*CFG_CMD_USB |*/ \ - CFG_CMD_REGINFO | \ + CFG_CMD_REGINFO | \ CFG_CMD_ELF) /* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ #include #define CONFIG_BOOTDELAY 3 -#define CONFIG_BOOTARGS "root=/dev/docbp mem=48M" +#define CONFIG_BOOTARGS "root=/dev/msdk mem=48M" #define CONFIG_ETHADDR 08:00:3e:26:0a:5c -#define CONFIG_NETMASK 255.255.255.0 +#define CONFIG_NETMASK 255.255.255.0 #define CONFIG_IPADDR 192.168.0.22 #define CONFIG_SERVERIP 192.168.0.11 #define CONFIG_BOOTFILE "mx1ads" -/*#define CONFIG_BOOTCOMMAND "tftp; bootm" */ +#define CONFIG_BOOTCOMMAND "tftp; bootm" #if (CONFIG_COMMANDS & CFG_CMD_KGDB) #define CONFIG_KGDB_BAUDRATE 115200 /* speed to run kgdb serial port */ @@ -114,10 +116,10 @@ * Miscellaneous configurable options */ -#define CFG_HUSH_PARSER 1 +#define CFG_HUSH_PARSER 1 #define CFG_PROMPT_HUSH_PS2 "> " -#define CFG_LONGHELP /* undef to save memory */ +#define CFG_LONGHELP /* undef to save memory */ #ifdef CFG_HUSH_PARSER #define CFG_PROMPT "MX1ADS$ " /* Monitor Command Prompt */ @@ -125,21 +127,20 @@ #define CFG_PROMPT "MX1ADS=> " /* Monitor Command Prompt */ #endif -#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ -#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) +#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ -#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_MAXARGS 16 /* max number of command args */ #define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ #define CFG_MEMTEST_START 0x09000000 /* memtest works on */ #define CFG_MEMTEST_END 0x0AF00000 /* 63 MB in DRAM */ -#undef CFG_CLKS_IN_HZ /* everything, incl board info, in Hz */ - -#define CFG_LOAD_ADDR 0x08800000 /* default load address */ - - -#define CFG_HZ 1000 +#undef CFG_CLKS_IN_HZ /* everything, incl board info, in Hz */ +#define CFG_LOAD_ADDR 0x08800000 /* default load address */ +/*#define CFG_HZ 1000 */ +#define CFG_HZ 3686400 +#define CFG_CPUSPEED 0x141 /* valid baudrates */ #define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } @@ -159,27 +160,35 @@ * Physical Memory Map */ +#define CONFIG_NR_DRAM_BANKS 1 /* we have 1 bank of SDRAM */ +#define PHYS_SDRAM_1 0x08000000 /* SDRAM on CSD0 */ +#define PHYS_SDRAM_1_SIZE 0x04000000 /* 64 MB */ -#define CONFIG_NR_DRAM_BANKS 1 /* we have 1 bank of SDRAM */ -#define PHYS_SDRAM_1 0x08000000 /* SDRAM on CSD0 */ -#define PHYS_SDRAM_1_SIZE 0x04000000 /* 64 MB */ - -#define CFG_MAX_FLASH_BANKS 1 /* 1 bank of SyncFlash */ -#define CFG_FLASH_BASE 0x0C000000 /* SyncFlash on CSD1 */ -#define FLASH_BANK_SIZE 0x01000000 /* 16 MB Total */ - +#define CFG_MAX_FLASH_BANKS 1 /* 1 bank of SyncFlash */ +#define CFG_FLASH_BASE 0x0C000000 /* SyncFlash on CSD1 */ +#define FLASH_BANK_SIZE 0x01000000 /* 16 MB Total */ /*----------------------------------------------------------------------- * FLASH and environment organization */ - #define CONFIG_SYNCFLASH 1 #define PHYS_FLASH_SIZE 0x01000000 #define CFG_MAX_FLASH_SECT (16) -#define CFG_ENV_ADDR (CFG_FLASH_BASE+0x00ff0000) +#define CFG_ENV_ADDR (CFG_FLASH_BASE+0x00ff8000) -#define CFG_ENV_IS_IN_FLASH 1 -#define CFG_ENV_SIZE 0x0f000 /* Total Size of Environment Sector */ +#define CFG_ENV_IS_IN_FLASH 1 +#define CFG_ENV_SIZE 0x04000 /* Total Size of Environment Sector */ #define CFG_ENV_SECT_SIZE 0x100000 + +/*----------------------------------------------------------------------- + * Enable passing ATAGS + */ + +#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */ +#define CONFIG_SETUP_MEMORY_TAGS 1 + +#define CONFIG_SYS_CLK_FREQ 16780000 +#define CONFIG_SYSPLL_CLK_FREQ 16000000 + #endif /* __CONFIG_H */ diff --git a/include/configs/mx1fs2.h b/include/configs/mx1fs2.h new file mode 100644 index 0000000000..61a3b29612 --- /dev/null +++ b/include/configs/mx1fs2.h @@ -0,0 +1,291 @@ +/* + * Copyright (C) 2004 Sascha Hauer, Pengutronix + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +#define CONFIG_ARM920T 1 /* this is an ARM920T CPU */ +#define CONFIG_IMX 1 /* in a Motorola MC9328MXL Chip */ +#define CONFIG_MX1FS2 1 /* on a mx1fs2 board */ +#undef CONFIG_USE_IRQ /* don't need use IRQ/FIQ */ + +/* + * Select serial console configuration + */ +#undef _CONFIG_UART1 /* internal uart 1 */ +#define _CONFIG_UART2 /* internal uart 2 */ +#undef _CONFIG_UART3 /* internal uart 3 */ +#undef _CONFIG_UART4 /* internal uart 4 */ +#undef CONFIG_SILENT_CONSOLE /* use this to disable output */ + +/* + * Definition of u-boot build in commands. Check out CONFIG_CMD_DFL if + * neccessary in include/cmd_confdefs.h file. (Un)comment for getting + * functionality or size of u-boot code. + */ +#define CONFIG_COMMANDS (CONFIG_CMD_DFL \ + & ~CFG_CMD_LOADS \ + & ~CFG_CMD_CONSOLE \ + & ~CFG_CMD_AUTOSCRIPT \ + & ~CFG_CMD_NET \ + & ~CFG_CMD_PING \ + & ~CFG_CMD_DHCP \ + | CFG_CMD_JFFS2 \ + ) + +#include + +/* + * Boot options. Setting delay to -1 stops autostart count down. + */ +#define CONFIG_BOOTDELAY 10 +#define CONFIG_BOOTARGS "root=/dev/mtdblock4 console=ttySMX0,115200n8 rootfstype=jffs2" +#define CONFIG_BOOTCOMMAND "bootm 10080000" +#define CONFIG_SHOW_BOOT_PROGRESS + +/* + * General options for u-boot. Modify to save memory foot print + */ +#define CFG_LONGHELP /* undef saves memory */ +#define CFG_PROMPT "mx1fs2> " /* prompt string */ +#define CFG_CBSIZE 256 /* console I/O buffer */ +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* print buffer size */ +#define CFG_MAXARGS 16 /* max command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* boot args buf size */ + +#define CFG_MEMTEST_START 0x08100000 /* memtest test area */ +#define CFG_MEMTEST_END 0x08F00000 + +#undef CFG_CLKS_IN_HZ /* use HZ for freq. display */ + +#define CFG_HZ 3686400 /* incrementer freq: 3.6864 MHz */ +#define CFG_CPUSPEED 0x141 /* core clock - register value */ + +#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } +#define CONFIG_BAUDRATE 115200 +/* + * Definitions related to passing arguments to kernel. + */ +#define CONFIG_CMDLINE_TAG 1 /* send commandline to Kernel */ +#define CONFIG_SETUP_MEMORY_TAGS 1 /* send memory definition to kernel */ +#define CONFIG_INITRD_TAG 1 /* send initrd params */ +#undef CONFIG_VFD /* do not send framebuffer setup */ + +#define CFG_JFFS_CUSTOM_PART +/* + * Malloc pool need to host env + 128 Kb reserve for other allocations. + */ +#define CFG_MALLOC_LEN (CFG_ENV_SIZE + (128<<10) ) + + +#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */ + +#define CONFIG_STACKSIZE (120<<10) /* stack size */ + +#ifdef CONFIG_USE_IRQ +#define CONFIG_STACKSIZE_IRQ (4<<10) /* IRQ stack */ +#define CONFIG_STACKSIZE_FIQ (4<<10) /* FIQ stack */ +#endif + +/* SDRAM Setup Values + * 0x910a8300 Precharge Command CAS 3 + * 0x910a8200 Precharge Command CAS 2 + * + * 0xa10a8300 AutoRefresh Command CAS 3 + * 0xa10a8200 Set AutoRefresh Command CAS 2 + */ +#define PRECHARGE_CMD 0x910a8300 +#define AUTOREFRESH_CMD 0xa10a8300 + +#define CONFIG_INIT_CRITICAL + +#define BUS32BIT_VERSION +/* + * SDRAM Memory Map + */ +#define CONFIG_NR_DRAM_BANKS 1 /* we have 1 bank of SDRAM */ +#define MX1FS2_SDRAM_1 0x08000000 /* SDRAM bank #1 */ +#ifdef BUS32BIT_VERSION +#define MX1FS2_SDRAM_1_SIZE (0x04000000 - 0x100000) /* 64 MB - 1M Framebuffer */ +#else +#define MX1FS2_SDRAM_1_SIZE (0x01FC0000 - 0x100000) /* 32 MB - 1M Framebuffer */ +#endif +/* + * Flash Controller settings + */ + +#define CFG_MAX_FLASH_BANKS 1 /* FLASH banks count (not chip count)*/ +#define CFG_MAX_FLASH_SECT 256 /* number of sector in FLASH bank */ + +#ifdef BUS32BIT_VERSION +#define MX1FS2_FLASH_BUS_WIDTH 4 /* we use 32 bit FLASH memory... */ +#define MX1FS2_FLASH_INTERLEAVE 2 /* ... made of 2 chips */ +#define MX1FS2_FLASH_BANK_SIZE 0x02000000 /* size of one flash bank*/ +#define MX1FS2_FLASH_SECT_SIZE 0x00020000 /* size of erase sector */ +#define MX1FS2_JFFS2_PART0_START 0x10200000 +#define MX1FS2_JFFS2_PART0_SIZE 0x00500000 +#define MX1FS2_JFFS2_PART1_START 0x10700000 +#define MX1FS2_JFFS2_PART1_SIZE 0x00900000 +#else +#define MX1FS2_FLASH_BUS_WIDTH 2 /* we use 16 bit FLASH memory... */ +#define MX1FS2_FLASH_INTERLEAVE 1 /* ... made of 1 chip */ +#define MX1FS2_FLASH_BANK_SIZE 0x01000000 /* size of one flash bank*/ +#define MX1FS2_FLASH_SECT_SIZE 0x00010000 /* size of erase sector */ +#endif +#define MX1FS2_FLASH_BASE 0x10000000 /* location of flash memory */ +#define MX1FS2_FLASH_UNLOCK 1 /* perform hw unlock first */ + +/* This should be defined if CFI FLASH device is present. Actually benefit + is not so clear to me. In other words we can provide more informations + to user, but this expects more complex flash handling we do not provide + now.*/ +#undef CFG_FLASH_CFI + +#define CFG_FLASH_ERASE_TOUT (2*CFG_HZ) /* timeout for Erase operation */ +#define CFG_FLASH_WRITE_TOUT (2*CFG_HZ) /* timeout for Write operation */ + +#define CFG_FLASH_BASE MX1FS2_FLASH_BASE + +/* + * This is setting for JFFS2 support in u-boot. + * Right now there is no gain for user, but later on booting kernel might be + * possible. Consider using XIP kernel running from flash to save RAM + * footprint. + * NOTE: Enable CFG_CMD_JFFS2 for JFFS2 support. + */ +#define CFG_JFFS2_FIRST_BANK 0 +#define CFG_JFFS2_FIRST_SECTOR 5 +#define CFG_JFFS2_NUM_BANKS 1 + +/* + * Environment setup. Definitions of monitor location and size with + * definition of environment setup ends up in 2 possibilities. + * 1. Embeded environment - in u-boot code is space for environment + * 2. Environment is read from predefined sector of flash + * Right now we support 2. possiblity, but expecting no env placed + * on mentioned address right now. This also needs to provide whole + * sector for it - for us 256Kb is really waste of memory. U-boot uses + * default env. and until kernel parameters could be sent to kernel + * env. has no sense to us. + */ + +#define CFG_MONITOR_BASE 0x10000000 +#define CFG_MONITOR_LEN 0x20000 /* 128b ( 1 flash sector ) */ +#define CFG_ENV_IS_IN_FLASH 1 +#define CFG_ENV_ADDR 0x10020000 /* absolute address for now */ +#define CFG_ENV_SIZE 0x20000 + +#define CONFIG_ENV_OVERWRITE 1 /* env is not writable now */ + +/* Setup CS4 and CS5 */ +#define CFG_GIUS_A_VAL 0x0003fffe + +/* + * CSxU_VAL: + * 63| x x x x | x x x x | x x x x | x x x x | x x x x | x x x x | x x x x | x x x x|32 + * |DTACK_SEL|0|BCD | BCS | PSZ|PME|SYNC| DOL | CNC| WSC | 0| WWS | EDC | + * + * CSxL_VAL: + * 31| x x x x | x x x x | x x x x | x x x x | x x x x | x x x x | x x x x | x x x x| 0 + * | OEA | OEN | WEA | WEN | CSA |EBC| DSZ | 0|SP|0|WP| 0 0|PA|CSEN| + */ + +#define CFG_CS0U_VAL 0x00008C00 +#define CFG_CS0L_VAL 0x22222601 +#define CFG_CS1U_VAL 0x00008C00 +#define CFG_CS1L_VAL 0x22222301 +#define CFG_CS4U_VAL 0x00008C00 +#define CFG_CS4L_VAL 0x22222301 +#define CFG_CS5U_VAL 0x00008C00 +#define CFG_CS5L_VAL 0x22222301 + +/* f_{dpll}=2*f{ref}*(MFI+MFN/(MFD+1))/(PD+1) + f_ref=16,777MHz + + 0x002a141f: 191,9944MHz + 0x040b2007: 144MHz + 0x042a141f: 96MHz + 0x0811140d: 64MHz + 0x040e200e: 150MHz + 0x00321431: 200MHz + + 0x08001800: 64MHz mit 16er Quarz + 0x04001800: 96MHz mit 16er Quarz + 0x04002400: 144MHz mit 16er Quarz + + 31 |x x x x|x x x x|x x x x|x x x x|x x x x|x x x x|x x x x|x x x x| 0 + |XXX|--PD---|-------MFD---------|XXX|--MFI--|-----MFN-----------| */ + +#define CFG_MPCTL0_VAL 0x07E723AD +#define CFG_MPCTL1_VAL 0x00000040 +#define CFG_PCDR_VAL 0x00010005 +#define CFG_GPCR_VAL 0x00000FFB + +#define USE_16M_OSZI /* If you have one, you want to use it + The internal 32kHz oszillator jitters */ +#ifdef USE_16M_OSZI + +#define CFG_SPCTL0_VAL 0x04001401 +#define CFG_SPCTL1_VAL 0x0C000040 +#define CFG_CSCR_VAL 0x07030003 +#define CONFIG_SYS_CLK_FREQ 16780000 +#define CONFIG_SYSPLL_CLK_FREQ 16000000 + +#else + +#define CFG_SPCTL0_VAL 0x07E716D1 +#define CFG_CSCR_VAL 0x06000003 +#define CONFIG_SYS_CLK_FREQ 16780000 +#define CONFIG_SYSPLL_CLK_FREQ 16780000 + +#endif + +/* + * Well this has to be defined, but on the other hand it is used differently + * one may expect. For instance loadb command do not cares :-) + * So advice is - do not relay on this... + */ +#define CFG_LOAD_ADDR 0x08400000 + +#define CFG_FMCR_VAL 0x00000003 /* Reset Default */ + +/* Bit[0:3] contain PERCLK1DIV for UART 1 + 0x000b00b ->b<- -> 192MHz/12=16MHz + 0x000b00b ->8<- -> 144MHz/09=16MHz + 0x000b00b ->3<- -> 64MHz/4=16MHz */ + +#ifdef _CONFIG_UART1 +#define CONFIG_IMX_SERIAL1 +#elif defined _CONFIG_UART2 +#define CONFIG_IMX_SERIAL2 +#elif defined _CONFIG_UART3 | defined _CONFIG_UART4 +#define CONFIG_IMX_SERIAL_NONE +#define CFG_NS16550 +#define CFG_NS16550_SERIAL +#define CFG_NS16550_CLK 3686400 +#define CFG_NS16550_REG_SIZE 1 +#define CONFIG_CONS_INDEX 1 +#ifdef _CONFIG_UART3 +#define CFG_NS16550_COM1 0x15000000 +#elif defined _CONFIG_UART4 +#define CFG_NS16550_COM1 0x16000000 +#endif +#endif + +#endif /* __CONFIG_H */ diff --git a/include/configs/scb9328.h b/include/configs/scb9328.h new file mode 100644 index 0000000000..6cd91269d4 --- /dev/null +++ b/include/configs/scb9328.h @@ -0,0 +1,357 @@ +/* + * Copyright (C) 2003 ETC s.r.o. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + * + * Written by Peter Figuli , 2003. + * + * 2003/13/06 Initial MP10 Support copied from wepep250 + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +#define CONFIG_ARM920T 1 /* this is an ARM920T CPU */ +#define CONFIG_IMX 1 /* in a Motorola MC9328MXL Chip */ +#define CONFIG_SCB9328 1 /* on a scb9328tronix board */ +#undef CONFIG_USE_IRQ /* don't need use IRQ/FIQ */ + +#define CONFIG_IMX_SERIAL1 +/* + * Select serial console configuration + */ + + +/* + * Definition of u-boot build in commands. Check out CONFIG_CMD_DFL if + * neccessary in include/cmd_confdefs.h file. (Un)comment for getting + * functionality or size of u-boot code. + */ +#define CONFIG_COMMANDS (CONFIG_CMD_DFL \ + & ~CFG_CMD_LOADS \ + & ~CFG_CMD_CONSOLE \ + & ~CFG_CMD_AUTOSCRIPT \ + | CFG_CMD_NET \ + | CFG_CMD_PING \ + | CFG_CMD_DHCP \ + ) + +#include + +/* + * Boot options. Setting delay to -1 stops autostart count down. + * NOTE: Sending parameters to kernel depends on kernel version and + * 2.4.19-rmk6-pxa1 patch used while my u-boot coding didn't accept + * parameters at all! Do not get confused by them so. + */ +#define CONFIG_BOOTDELAY -1 +#define CONFIG_BOOTARGS "console=ttySMX0,115200n8 root=/dev/mtdblock3 rootfstype=jffs2 mtdparts=scb9328_flash:128k(U-boot)ro,128k(U-boot_env),1m(kernel),4m(root),4m(fs) eval_board=evk9328" +#define CONFIG_BOOTCOMMAND "bootm 10040000" +#define CONFIG_SHOW_BOOT_PROGRESS +#define CONFIG_ETHADDR 80:81:82:83:84:85 +#define CONFIG_NETMASK 255.255.255.0 +#define CONFIG_IPADDR 10.10.10.9 +#define CONFIG_SERVERIP 10.10.10.10 + +/* + * General options for u-boot. Modify to save memory foot print + */ +#define CFG_LONGHELP /* undef saves memory */ +#define CFG_PROMPT "scb9328> " /* prompt string */ +#define CFG_CBSIZE 256 /* console I/O buffer */ +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* print buffer size */ +#define CFG_MAXARGS 16 /* max command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* boot args buf size */ + +#define CFG_MEMTEST_START 0x08100000 /* memtest test area */ +#define CFG_MEMTEST_END 0x08F00000 + +#undef CFG_CLKS_IN_HZ /* use HZ for freq. display */ + +#define CFG_HZ 3686400 /* incrementer freq: 3.6864 MHz */ +#define CFG_CPUSPEED 0x141 /* core clock - register value */ + +#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } +#define CONFIG_BAUDRATE 115200 +/* + * Definitions related to passing arguments to kernel. + */ +#define CONFIG_CMDLINE_TAG 1 /* send commandline to Kernel */ +#define CONFIG_SETUP_MEMORY_TAGS 1 /* send memory definition to kernel */ +#define CONFIG_INITRD_TAG 1 /* send initrd params */ +#undef CONFIG_VFD /* do not send framebuffer setup */ + + +/* + * Malloc pool need to host env + 128 Kb reserve for other allocations. + */ +#define CFG_MALLOC_LEN (CFG_ENV_SIZE + (128<<10) ) + + +#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */ + +#define CONFIG_STACKSIZE (120<<10) /* stack size */ + +#ifdef CONFIG_USE_IRQ +#define CONFIG_STACKSIZE_IRQ (4<<10) /* IRQ stack */ +#define CONFIG_STACKSIZE_FIQ (4<<10) /* FIQ stack */ +#endif + +/* SDRAM Setup Values +0x910a8300 Precharge Command CAS 3 +0x910a8200 Precharge Command CAS 2 + +0xa10a8300 AutoRefresh Command CAS 3 +0xa10a8200 Set AutoRefresh Command CAS 2 */ + +#define PRECHARGE_CMD 0x910a8200 +#define AUTOREFRESH_CMD 0xa10a8200 +#define CONFIG_INIT_CRITICAL + +/* + * SDRAM Memory Map + */ +/* SH FIXME */ +#define CONFIG_NR_DRAM_BANKS 1 /* we have 1 bank of SDRAM */ +#define SCB9328_SDRAM_1 0x08000000 /* SDRAM bank #1 */ +#define SCB9328_SDRAM_1_SIZE 0x01000000 /* 16 MB */ + +/* + * Flash Controller settings + */ + +/* + * Hardware drivers + */ + + +/* + * Configuration for FLASH memory for the Synertronixx board + */ + +/* #define SCB9328_FLASH_32M */ + +/* 32MB */ +#ifdef SCB9328_FLASH_32M +#define CFG_MAX_FLASH_BANKS 1 /* FLASH banks count (not chip count)*/ +#define CFG_MAX_FLASH_SECT 256 /* number of sector in FLASH bank */ +#define SCB9328_FLASH_BUS_WIDTH 2 /* we use 16 bit FLASH memory... */ +#define SCB9328_FLASH_INTERLEAVE 1 /* ... made of 1 chip */ +#define SCB9328_FLASH_BANK_SIZE 0x02000000 /* size of one flash bank */ +#define SCB9328_FLASH_SECT_SIZE 0x00020000 /* size of erase sector */ +#define SCB9328_FLASH_BASE 0x10000000 /* location of flash memory */ +#define SCB9328_FLASH_UNLOCK 1 /* perform hw unlock first */ +#else + +/* 16MB */ +#define CFG_MAX_FLASH_BANKS 1 /* FLASH banks count (not chip count)*/ +#define CFG_MAX_FLASH_SECT 128 /* number of sector in FLASH bank */ +#define SCB9328_FLASH_BUS_WIDTH 2 /* we use 16 bit FLASH memory... */ +#define SCB9328_FLASH_INTERLEAVE 1 /* ... made of 1 chip */ +#define SCB9328_FLASH_BANK_SIZE 0x01000000 /* size of one flash bank */ +#define SCB9328_FLASH_SECT_SIZE 0x00020000 /* size of erase sector */ +#define SCB9328_FLASH_BASE 0x10000000 /* location of flash memory */ +#define SCB9328_FLASH_UNLOCK 1 /* perform hw unlock first */ +#endif /* SCB9328_FLASH_32M */ + +/* This should be defined if CFI FLASH device is present. Actually benefit + is not so clear to me. In other words we can provide more informations + to user, but this expects more complex flash handling we do not provide + now.*/ +#undef CFG_FLASH_CFI + +#define CFG_FLASH_ERASE_TOUT (2*CFG_HZ) /* timeout for Erase operation */ +#define CFG_FLASH_WRITE_TOUT (2*CFG_HZ) /* timeout for Write operation */ + +#define CFG_FLASH_BASE SCB9328_FLASH_BASE + +/* + * This is setting for JFFS2 support in u-boot. + * Right now there is no gain for user, but later on booting kernel might be + * possible. Consider using XIP kernel running from flash to save RAM + * footprint. + * NOTE: Enable CFG_CMD_JFFS2 for JFFS2 support. + */ +#define CFG_JFFS2_FIRST_BANK 0 +#define CFG_JFFS2_FIRST_SECTOR 5 +#define CFG_JFFS2_NUM_BANKS 1 + +/* + * Environment setup. Definitions of monitor location and size with + * definition of environment setup ends up in 2 possibilities. + * 1. Embeded environment - in u-boot code is space for environment + * 2. Environment is read from predefined sector of flash + * Right now we support 2. possiblity, but expecting no env placed + * on mentioned address right now. This also needs to provide whole + * sector for it - for us 256Kb is really waste of memory. U-boot uses + * default env. and until kernel parameters could be sent to kernel + * env. has no sense to us. + */ + +/* Setup for PA23 which is Reset Default PA23 but has to become + CS5 */ + +#define CFG_GPR_A_VAL 0x00800000 +#define CFG_GIUS_A_VAL 0x0043fffe + +#define CFG_MONITOR_BASE 0x10000000 +#define CFG_MONITOR_LEN 0x20000 /* 128b ( 1 flash sector ) */ +#define CFG_ENV_IS_IN_FLASH 1 +#define CFG_ENV_ADDR 0x10020000 /* absolute address for now */ +#define CFG_ENV_SIZE 0x20000 + +#define CONFIG_ENV_OVERWRITE 1 /* env is not writable now */ + +/* + * CSxU_VAL: + * 63| x x x x | x x x x | x x x x | x x x x | x x x x | x x x x | x x x x | x x x x|32 + * |DTACK_SEL|0|BCD | BCS | PSZ|PME|SYNC| DOL | CNC| WSC | 0| WWS | EDC | + * + * CSxL_VAL: + * 31| x x x x | x x x x | x x x x | x x x x | x x x x | x x x x | x x x x | x x x x| 0 + * | OEA | OEN | WEA | WEN | CSA |EBC| DSZ | 0|SP|0|WP| 0 0|PA|CSEN| + */ + +#define CFG_CS0U_VAL 0x000F2000 +#define CFG_CS0L_VAL 0x11110d01 +#define CFG_CS1U_VAL 0x000F0a00 +#define CFG_CS1L_VAL 0x11110601 +#define CFG_CS2U_VAL 0x0 +#define CFG_CS2L_VAL 0x0 + +#define CFG_CS3U_VAL 0x000FFFFF +#define CFG_CS3L_VAL 0x00000303 + +#define CFG_CS4U_VAL 0x000F0a00 +#define CFG_CS4L_VAL 0x11110301 + +/* CNC == 3 too long + #define CFG_CS5U_VAL 0x0000C210 */ + +/* #define CFG_CS5U_VAL 0x00008400 + mal laenger mahcen, ob der bei 150MHz laenger haelt dann und + kaum langsamer ist */ +/* #define CFG_CS5U_VAL 0x00009400 + #define CFG_CS5L_VAL 0x11010D03 */ + +#define CFG_CS5U_VAL 0x00008400 +#define CFG_CS5L_VAL 0x00000D03 + +#define CONFIG_DRIVER_DM9000 1 +#define CONFIG_DRIVER_DM9000 1 +#define CONFIG_DM9000_BASE 0x16000000 +#define DM9000_IO CONFIG_DM9000_BASE +#define DM9000_DATA (CONFIG_DM9000_BASE+4) +/* #define CONFIG_DM9000_USE_8BIT */ +#define CONFIG_DM9000_USE_16BIT +/* #define CONFIG_DM9000_USE_32BIT */ + +/* f_{dpll}=2*f{ref}*(MFI+MFN/(MFD+1))/(PD+1) + f_ref=16,777MHz + + 0x002a141f: 191,9944MHz + 0x040b2007: 144MHz + 0x042a141f: 96MHz + 0x0811140d: 64MHz + 0x040e200e: 150MHz + 0x00321431: 200MHz + + 0x08001800: 64MHz mit 16er Quarz + 0x04001800: 96MHz mit 16er Quarz + 0x04002400: 144MHz mit 16er Quarz + + 31 |x x x x|x x x x|x x x x|x x x x|x x x x|x x x x|x x x x|x x x x| 0 + |XXX|--PD---|-------MFD---------|XXX|--MFI--|-----MFN-----------| */ + +#define CPU200 + +#ifdef CPU200 +#define CFG_MPCTL0_VAL 0x00321431 +#else +#define CFG_MPCTL0_VAL 0x040e200e +#endif + +/* #define BUS64 */ +#define BUS72 + +#ifdef BUS72 +#define CFG_SPCTL0_VAL 0x04002400 +#endif + +#ifdef BUS96 +#define CFG_SPCTL0_VAL 0x04001800 +#endif + +#ifdef BUS64 +#define CFG_SPCTL0_VAL 0x08001800 +#endif + +/* Das ist der BCLK Divider, der aus der System PLL + BCLK und HCLK erzeugt: + 31 | xxxx xxxx xxxx xxxx xx10 11xx xxxx xxxx | 0 + 0x2f008403 : 192MHz/2=96MHz, 144MHz/2=72MHz PRESC=1->BCLKDIV=2 + 0x2f008803 : 192MHz/3=64MHz, 240MHz/3=80MHz PRESC=1->BCLKDIV=2 + 0x2f001003 : 192MHz/5=38,4MHz + 0x2f000003 : 64MHz/1 + Bit 22: SPLL Restart + Bit 21: MPLL Restart */ + +#ifdef BUS64 +#define CFG_CSCR_VAL 0x2f030003 +#endif + +#ifdef BUS72 +#define CFG_CSCR_VAL 0x2f030403 +#endif + +/* + * Well this has to be defined, but on the other hand it is used differently + * one may expect. For instance loadb command do not cares :-) + * So advice is - do not relay on this... + */ +#define CFG_LOAD_ADDR 0x08400000 + +#define MHZ16QUARZINUSE + +#ifdef MHZ16QUARZINUSE +#define CONFIG_SYSPLL_CLK_FREQ 16000000 +#else +#define CONFIG_SYSPLL_CLK_FREQ 16780000 +#endif + +#define CONFIG_SYS_CLK_FREQ 16780000 + +/* FMCR Bit 0 becomes 0 to make CS3 CS3 :P */ +#define CFG_FMCR_VAL 0x00000001 + +/* Bit[0:3] contain PERCLK1DIV for UART 1 + 0x000b00b ->b<- -> 192MHz/12=16MHz + 0x000b00b ->8<- -> 144MHz/09=16MHz + 0x000b00b ->3<- -> 64MHz/4=16MHz */ + +#ifdef BUS96 +#define CFG_PCDR_VAL 0x000b00b5 +#endif + +#ifdef BUS64 +#define CFG_PCDR_VAL 0x000b00b3 +#endif + +#ifdef BUS72 +#define CFG_PCDR_VAL 0x000b00b8 +#endif + +#endif /* __CONFIG_H */ diff --git a/include/devices.h b/include/devices.h index 9f2a0c34ac..09c2c5f511 100644 --- a/include/devices.h +++ b/include/devices.h @@ -39,7 +39,7 @@ typedef struct { int flags; /* Device flags: input/output/system */ int ext; /* Supported extensions */ - char name[8]; /* Device name */ + char name[16]; /* Device name */ /* GENERAL functions */ diff --git a/include/mc9328.h b/include/mc9328.h deleted file mode 100644 index 2a6e7577fb..0000000000 --- a/include/mc9328.h +++ /dev/null @@ -1,1051 +0,0 @@ -/* - * include/mc9328.h - * - * (c) Copyright 2004 - * Techware Information Technology, Inc. - * http://www.techware.com.tw/ - * - * Ming-Len Wu - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation; either version 2 of - * the License, or (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, - * MA 02111-1307 USA - */ - -#ifndef __MC9328_H__ -#define __MC9328_H__ - -typedef volatile unsigned long VU32; -typedef VU32 * P_VU32; - -#define __REG(x) (*((volatile u32 *)(x))) - -/* - * MX1 Chip selects & internal memory's - */ -#define MX1_DMI_PHYS 0x00000000 /* double map image */ -#define MX1_BROM_PHYS 0x00100000 /* Bootstrape ROM */ -#define MX1_ESRAM_PHYS 0x00300000 /* Embedded SRAM (128KB)*/ - -#define MX1_CSD0_PHYS 0x08000000 /* CSD0 64MB (SDRAM) */ -#define MX1_CSD1_PHYS 0x0C000000 /* CSD1 64MB (SDRAM) */ -#define MX1_CS0_PHYS 0x10000000 /* CS0 32MB (Flash) */ -#define MX1_CS1_PHYS 0x12000000 /* CS1 16MB (Flash) */ -#define MX1_CS2_PHYS 0x13000000 /* CS2 16MB (Ext SRAM) */ -#define MX1_CS3_PHYS 0x14000000 /* CS3 16MB (Spare) */ -#define MX1_CS4_PHYS 0x15000000 /* CS4 16MB (Spare) */ -#define MX1_CS5_PHYS 0x16000000 /* CS5 16MB (Spare) */ - -/* - * MX1 Watchdog registers - */ -#define MX1_WCR __REG(0x00201000) /* Watchdog Control Register */ -#define MX1_WSR __REG(0x00201004) /* Watchdog Service Register */ -#define MX1_WSTR __REG(0x00201008) /* Watchdog Status Register */ - -/* - * MX1 Timer registers - */ -#define MX1_TCTL1 __REG(0x00202000) /* Timer 1 Control Register */ -#define MX1_TPRER1 __REG(0x00202004) /* Timer 1 Prescaler Register */ -#define MX1_TCMP1 __REG(0x00202008) /* Timer 1 Compare Register */ -#define MX1_TCR1 __REG(0x0020200C) /* Timer 1 Capture Register */ -#define MX1_TCN1 __REG(0x00202010) /* Timer 1 Counter Register */ -#define MX1_TSTAT1 __REG(0x00202014) /* Timer 1 Status Register */ - -#define MX1_TCTL2 __REG(0x00203000) /* Timer 2 Control Register */ -#define MX1_TPRER2 __REG(0x00203004) /* Timer 2 Prescaler Register */ -#define MX1_TCMP2 __REG(0x00203008) /* Timer 2 Compare Register */ -#define MX1_TCR2 __REG(0x0020300C) /* Timer 2 Capture Register */ -#define MX1_TCN2 __REG(0x00203010) /* Timer 2 Counter Register */ -#define MX1_TSTAT2 __REG(0x00203014) /* Timer 2 Status Register */ - -/* - * MX1 RTC registers - */ -#define MX1_HOURMIN __REG(0x00204000) /* RTC Hour & Min Counter Registers */ -#define MX1_SECONDS __REG(0x00204004) /* RTC Seconds Counter Registers */ -#define MX1_ALRM_HM __REG(0x00204008) /* RTC Hour & Min Alarm Registers */ -#define MX1_ALRM_SEC __REG(0x0020400C) /* RTC Seconds Alarm Registers */ -#define MX1_RCCTL __REG(0x00204010) /* RTC Control Registers */ -#define MX1_RTCISR __REG(0x00204014) /* RTC Interrupt Status Registers */ -#define MX1_RTCIENR __REG(0x00204018) /* RTC Interrupt Enable Registers */ -#define MX1_STPWCH __REG(0x0020401C) /* RTC Stopwatch Minutes Registers */ -#define MX1_DAYR __REG(0x00204020) /* RTC Days Counter Registers */ -#define MX1_DAYALARM __REG(0x00204020) /* RTC Day Alarm Registers */ - -/* - * MX1 LCD Controller registers - */ -#define MX1_SSA __REG(0x00205000) /* Screen Start Address Register */ -#define MX1_SIZE __REG(0x00205004) /* Size Register */ -#define MX1_VPW __REG(0x00205008) /* Virtual Page Width Register */ -#define MX1_CPOS __REG(0x0020500C) /* LCD Cursor Position Register */ -#define MX1_LCWHB __REG(0x00205010) /* LCD Cursor Width Height & Blink Register */ -#define MX1_LCHCC __REG(0x00205014) /* LCD Color Cursor Mapping Register */ -#define MX1_PCR __REG(0x00205018) /* LCD Panel Configuration Register */ -#define MX1_HCR __REG(0x0020501C) /* Horizontal Configuration Register */ -#define MX1_VCR __REG(0x00205020) /* Vertical Configuration Register */ -#define MX1_POS __REG(0x00205024) /* Panning Offset Register */ -#define MX1_LGPMR __REG(0x00205028) /* LCD Gray Palette Mapping Register */ -#define MX1_PWMR __REG(0x0020502C) /* PWM Contrast Control Register */ -#define MX1_DMACR __REG(0x00205030) /* DMA Control Register */ -#define MX1_RMCR __REG(0x00205034) /* Refresh Mode Control Register */ -#define MX1_LCDICR __REG(0x00205038) /* Interrupt Configuration Register */ -#define MX1_LCDISR __REG(0x00205040) /* Interrupt Status Register */ - -/* - * MX1 UART registers - */ - -/* UART 1 */ -#define MX1_URX0D_1 __REG(0x00206000) /* UART 1 Receiver Register 0 */ -#define MX1_URX1D_1 __REG(0x00206004) /* UART 1 Receiver Register 1 */ -#define MX1_URX2D_1 __REG(0x00206008) /* UART 1 Receiver Register 2 */ -#define MX1_URX3D_1 __REG(0x0020600C) /* UART 1 Receiver Register 3 */ -#define MX1_URX4D_1 __REG(0x00206010) /* UART 1 Receiver Register 4 */ -#define MX1_URX5D_1 __REG(0x00206014) /* UART 1 Receiver Register 5 */ -#define MX1_URX6D_1 __REG(0x00206018) /* UART 1 Receiver Register 6 */ -#define MX1_URX7D_1 __REG(0x0020601C) /* UART 1 Receiver Register 7 */ -#define MX1_URX8D_1 __REG(0x00206020) /* UART 1 Receiver Register 8 */ -#define MX1_URX9D_1 __REG(0x00206024) /* UART 1 Receiver Register 9 */ -#define MX1_URX10D_1 __REG(0x00206028) /* UART 1 Receiver Register 10 */ -#define MX1_URX11D_1 __REG(0x0020602C) /* UART 1 Receiver Register 11 */ -#define MX1_URX12D_1 __REG(0x00206030) /* UART 1 Receiver Register 12 */ -#define MX1_URX13D_1 __REG(0x00206034) /* UART 1 Receiver Register 13 */ -#define MX1_URX14D_1 __REG(0x00206038) /* UART 1 Receiver Register 14 */ -#define MX1_URX15D_1 __REG(0x0020603c) /* UART 1 Receiver Register 15 */ - -#define MX1_UTX0D_1 __REG(0x00206040) /* UART 1 Transmitter Register 0 */ -#define MX1_UTX1D_1 __REG(0x00206044) /* UART 1 Transmitter Register 1 */ -#define MX1_UTX2D_1 __REG(0x00206048) /* UART 1 Transmitter Register 2 */ -#define MX1_UTX3D_1 __REG(0x0020604C) /* UART 1 Transmitter Register 3 */ -#define MX1_UTX4D_1 __REG(0x00206050) /* UART 1 Transmitter Register 4 */ -#define MX1_UTX5D_1 __REG(0x00206054) /* UART 1 Transmitter Register 5 */ -#define MX1_UTX6D_1 __REG(0x00206058) /* UART 1 Transmitter Register 6 */ -#define MX1_UTX7D_1 __REG(0x0020605C) /* UART 1 Transmitter Register 7 */ -#define MX1_UTX8D_1 __REG(0x00206060) /* UART 1 Transmitter Register 8 */ -#define MX1_UTX9D_1 __REG(0x00206064) /* UART 1 Transmitter Register 9 */ -#define MX1_UTX10D_1 __REG(0x00206068) /* UART 1 Transmitter Register 10 */ -#define MX1_UTX11D_1 __REG(0x0020606C) /* UART 1 Transmitter Register 11 */ -#define MX1_UTX12D_1 __REG(0x00206060) /* UART 1 Transmitter Register 12 */ -#define MX1_UTX13D_1 __REG(0x00206074) /* UART 1 Transmitter Register 13 */ -#define MX1_UTX14D_1 __REG(0x00206078) /* UART 1 Transmitter Register 14 */ -#define MX1_UTX15D_1 __REG(0x0020607c) /* UART 1 Transmitter Register 15 */ - -#define MX1_UCR1_1 __REG(0x00206080) /* UART 1 Control Register 1 */ -#define MX1_UCR2_1 __REG(0x00206084) /* UART 1 Control Register 2 */ -#define MX1_UCR3_1 __REG(0x00206088) /* UART 1 Control Register 3 */ -#define MX1_UCR4_1 __REG(0x0020608C) /* UART 1 Control Register 4 */ -#define MX1_UFCR_1 __REG(0x00206090) /* UART 1 FIFO Control Register */ -#define MX1_USR1_1 __REG(0x00206094) /* UART 1 Status Register 1 */ -#define MX1_USR2_1 __REG(0x00206098) /* UART 1 Status Register 2 */ -#define MX1_UESC_1 __REG(0x0020609C) /* UART 1 Escape Character Register */ -#define MX1_UTIM_1 __REG(0x002060A0) /* UART 1 Escape Timer Register */ -#define MX1_UBIR_1 __REG(0x002060A4) /* UART 1 BRM Incremental Register */ -#define MX1_UBMR_1 __REG(0x002060A8) /* UART 1 BRM Modulator Register */ -#define MX1_UBRC_1 __REG(0x002060AC) /* UART 1 Baud Rate Count Register */ -#define MX1_BIPR1_1 __REG(0x002060B0) /* UART 1 BRM Incremental Preset Register 1 */ -#define MX1_BIPR2_1 __REG(0x002060B4) /* UART 1 BRM Incremental Preset Register 2 */ -#define MX1_BIPR3_1 __REG(0x002060B8) /* UART 1 BRM Incremental Preset Register 3 */ -#define MX1_BIPR4_1 __REG(0x002060BC) /* UART 1 BRM Incremental Preset Register 4 */ -#define MX1_BMPR1_1 __REG(0x002060C0) /* UART 1 BRM Modulator Preset Register 1 */ -#define MX1_BMPR2_1 __REG(0x002060C4) /* UART 1 BRM Modulator Preset Register 2 */ -#define MX1_BMPR3_1 __REG(0x002060C8) /* UART 1 BRM Modulator Preset Register 3 */ -#define MX1_BMPR4_1 __REG(0x002060CC) /* UART 1 BRM Modulator Preset Register 4 */ -#define MX1_UTS_1 __REG(0x002060D0) /* UART 1 Test Register 1 */ - -/* UART 2 */ -#define MX1_URX0D_2 __REG(0x00207000) /* UART 2 Receiver Register 0 */ -#define MX1_URX1D_2 __REG(0x00207004) /* UART 2 Receiver Register 1 */ -#define MX1_URX2D_2 __REG(0x00207008) /* UART 2 Receiver Register 2 */ -#define MX1_URX3D_2 __REG(0x0020700C) /* UART 2 Receiver Register 3 */ -#define MX1_URX4D_2 __REG(0x00207010) /* UART 2 Receiver Register 4 */ -#define MX1_URX5D_2 __REG(0x00207014) /* UART 2 Receiver Register 5 */ -#define MX1_URX6D_2 __REG(0x00207018) /* UART 2 Receiver Register 6 */ -#define MX1_URX7D_2 __REG(0x0020701C) /* UART 2 Receiver Register 7 */ -#define MX1_URX8D_2 __REG(0x00207020) /* UART 2 Receiver Register 8 */ -#define MX1_URX9D_2 __REG(0x00207024) /* UART 2 Receiver Register 9 */ -#define MX1_URX10D_2 __REG(0x00207028) /* UART 2 Receiver Register 10 */ -#define MX1_URX11D_2 __REG(0x0020702C) /* UART 2 Receiver Register 11 */ -#define MX1_URX12D_2 __REG(0x00207030) /* UART 2 Receiver Register 12 */ -#define MX1_URX13D_2 __REG(0x00207034) /* UART 2 Receiver Register 13 */ -#define MX1_URX14D_2 __REG(0x00207038) /* UART 2 Receiver Register 14 */ -#define MX1_URX15D_2 __REG(0x0020703c) /* UART 2 Receiver Register 15 */ - -#define MX1_UTX0D_2 __REG(0x00207040) /* UART 2 Transmitter Register 0 */ -#define MX1_UTX1D_2 __REG(0x00207044) /* UART 2 Transmitter Register 1 */ -#define MX1_UTX2D_2 __REG(0x00207048) /* UART 2 Transmitter Register 2 */ -#define MX1_UTX3D_2 __REG(0x0020704C) /* UART 2 Transmitter Register 3 */ -#define MX1_UTX4D_2 __REG(0x00207050) /* UART 2 Transmitter Register 4 */ -#define MX1_UTX5D_2 __REG(0x00207054) /* UART 2 Transmitter Register 5 */ -#define MX1_UTX6D_2 __REG(0x00207058) /* UART 2 Transmitter Register 6 */ -#define MX1_UTX7D_2 __REG(0x0020705C) /* UART 2 Transmitter Register 7 */ -#define MX1_UTX8D_2 __REG(0x00207060) /* UART 2 Transmitter Register 8 */ -#define MX1_UTX9D_2 __REG(0x00207064) /* UART 2 Transmitter Register 9 */ -#define MX1_UTX10D_2 __REG(0x00207068) /* UART 2 Transmitter Register 10 */ -#define MX1_UTX11D_2 __REG(0x0020706C) /* UART 2 Transmitter Register 11 */ -#define MX1_UTX12D_2 __REG(0x00207060) /* UART 2 Transmitter Register 12 */ -#define MX1_UTX13D_2 __REG(0x00207074) /* UART 2 Transmitter Register 13 */ -#define MX1_UTX14D_2 __REG(0x00207078) /* UART 2 Transmitter Register 14 */ -#define MX1_UTX15D_2 __REG(0x0020707c) /* UART 2 Transmitter Register 15 */ - -#define MX1_UCR1_2 __REG(0x00207080) /* UART 2 Control Register 1 */ -#define MX1_UCR2_2 __REG(0x00207084) /* UART 2 Control Register 2 */ -#define MX1_UCR3_2 __REG(0x00207088) /* UART 2 Control Register 3 */ -#define MX1_UCR4_2 __REG(0x0020708C) /* UART 2 Control Register 4 */ -#define MX1_UFCR_2 __REG(0x00207090) /* UART 2 FIFO Control Register */ -#define MX1_USR1_2 __REG(0x00207094) /* UART 2 Status Register 1 */ -#define MX1_USR2_2 __REG(0x00207098) /* UART 2 Status Register 2 */ -#define MX1_UESC_2 __REG(0x0020709C) /* UART 2 Escape Character Register */ -#define MX1_UTIM_2 __REG(0x002070A0) /* UART 2 Escape Timer Register */ -#define MX1_UBIR_2 __REG(0x002070A4) /* UART 2 BRM Incremental Register */ -#define MX1_UBMR_2 __REG(0x002070A8) /* UART 2 BRM Modulator Register */ -#define MX1_UBRC_2 __REG(0x002070AC) /* UART 2 Baud Rate Count Register */ -#define MX1_BIPR1_2 __REG(0x002070B0) /* UART 2 BRM Incremental Preset Register 1 */ -#define MX1_BIPR2_2 __REG(0x002070B4) /* UART 2 BRM Incremental Preset Register 2 */ -#define MX1_BIPR3_2 __REG(0x002070B8) /* UART 2 BRM Incremental Preset Register 3 */ -#define MX1_BIPR4_2 __REG(0x002070BC) /* UART 2 BRM Incremental Preset Register 4 */ -#define MX1_BMPR1_2 __REG(0x002070C0) /* UART 2 BRM Modulator Preset Register 1 */ -#define MX1_BMPR2_2 __REG(0x002070C4) /* UART 2 BRM Modulator Preset Register 2 */ -#define MX1_BMPR3_2 __REG(0x002070C8) /* UART 2 BRM Modulator Preset Register 3 */ -#define MX1_BMPR4_2 __REG(0x002070CC) /* UART 2 BRM Modulator Preset Register 4 */ -#define MX1_UTS_2 __REG(0x002070D0) /* UART 2 Test Register 1 */ - -/* - * MX1 PWM registers - */ -#define MX1_PWMC __REG(0x00208000) /* PWM Control Register */ -#define MX1_PWMS __REG(0x00208004) /* PWM Sample Register */ -#define MX1_PWMP __REG(0x00208008) /* PWM Period Register */ -#define MX1_PWMCNT __REG(0x0020800C) /* PWM Counter Register */ - -/* - * MX1 DMAC registers - */ -#define MX1_DCR __REG(0x00209000) /* DMA Control Register */ -#define MX1_DISR __REG(0x00209004) /* DMA Interrupt Status Register */ -#define MX1_DIMR __REG(0x00209008) /* DMA Interrupt Mask Register */ -#define MX1_DBTOSR __REG(0x0020900C) /* DMA Burst Time-Out Status Register */ -#define MX1_DRTOSR __REG(0x00209010) /* DMA Request Time-Out Status Register */ -#define MX1_DSESR __REG(0x00209014) /* DMA Request Time-Out Status Register */ -#define MX1_DBOSR __REG(0x00209018) /* DMA Buffer Overflow Status Register */ -#define MX1_DBTOCR __REG(0x0020901C) /* DMA Burst Time-Out Control Register */ - -#define MX1_WSRA __REG(0x00209040) /* DMA W-Size Register A */ -#define MX1_XSRA __REG(0x00209044) /* DMA X-Size Register A */ -#define MX1_YSRA __REG(0x00209048) /* DMA Y-Size Register A */ - -#define MX1_WSRB __REG(0x0020904C) /* DMA W-Size Register B */ -#define MX1_XSRB __REG(0x00209050) /* DMA X-Size Register B */ -#define MX1_YSRB __REG(0x00209054) /* DMA Y-Size Register B */ - -/* Channel 0 */ - -#define MX1_SAR0 __REG(0x00209080) /* Channel 0 Source Address Register */ -#define MX1_DAR0 __REG(0x00209084) /* Channel 0 Destination Address Register */ -#define MX1_CNTR0 __REG(0x00209088) /* Channel 0 Count Register */ -#define MX1_CCR0 __REG(0x0020908C) /* Channel 0 Control Register */ -#define MX1_RSSR0 __REG(0x00209090) /* Channel 0 Request Source Select Register */ -#define MX1_BLR0 __REG(0x00209094) /* Channel 0 Burst Length Register */ -#define MX1_RTOR0 __REG(0x00209098) /* Channel 0 Request Time-Out Register */ -#define MX1_BUCR0 __REG(0x00209098) /* Channel 0 Bus Utilization Control Register */ - -/* Channel 1 */ - -#define MX1_SAR1 __REG(0x002090C0) /* Channel 1 Source Address Register */ -#define MX1_DAR1 __REG(0x002090C4) /* Channel 1 Destination Address Register */ -#define MX1_CNTR1 __REG(0x002090C8) /* Channel 1 Count Register */ -#define MX1_CCR1 __REG(0x002090CC) /* Channel 1 Control Register */ -#define MX1_RSSR1 __REG(0x002090D0) /* Channel 1 Request Source Select Register */ -#define MX1_BLR1 __REG(0x002090D4) /* Channel 1 Burst Length Register */ -#define MX1_RTOR1 __REG(0x002090D8) /* Channel 1 Request Time-Out Register */ -#define MX1_BUCR1 __REG(0x002090D8) /* Channel 1 Bus Utilization Control Register */ - -/* Channel 2 */ - -#define MX1_SAR2 __REG(0x00209100) /* Channel 2 Source Address Register */ -#define MX1_DAR2 __REG(0x00209104) /* Channel 2 Destination Address Register */ -#define MX1_CNTR2 __REG(0x00209108) /* Channel 2 Count Register */ -#define MX1_CCR2 __REG(0x0020910C) /* Channel 2 Control Register */ -#define MX1_RSSR2 __REG(0x00209110) /* Channel 2 Request Source Select Register */ -#define MX1_BLR2 __REG(0x00209114) /* Channel 2 Burst Length Register */ -#define MX1_RTOR2 __REG(0x00209118) /* Channel 2 Request Time-Out Register */ -#define MX1_BUCR2 __REG(0x00209118) /* Channel 2 Bus Utilization Control Register */ - -/* Channel 3 */ - -#define MX1_SAR3 __REG(0x00209140) /* Channel 3 Source Address Register */ -#define MX1_DAR3 __REG(0x00209144) /* Channel 3 Destination Address Register */ -#define MX1_CNTR3 __REG(0x00209148) /* Channel 3 Count Register */ -#define MX1_CCR3 __REG(0x0020914C) /* Channel 3 Control Register */ -#define MX1_RSSR3 __REG(0x00209150) /* Channel 3 Request Source Select Register */ -#define MX1_BLR3 __REG(0x00209154) /* Channel 3 Burst Length Register */ -#define MX1_RTOR3 __REG(0x00209158) /* Channel 3 Request Time-Out Register */ -#define MX1_BUCR3 __REG(0x00209158) /* Channel 3 Bus Utilization Control Register */ - -/* Channel 4 */ - -#define MX1_SAR4 __REG(0x00209180) /* Channel 4 Source Address Register */ -#define MX1_DAR4 __REG(0x00209184) /* Channel 4 Destination Address Register */ -#define MX1_CNTR4 __REG(0x00209188) /* Channel 4 Count Register */ -#define MX1_CCR4 __REG(0x0020918C) /* Channel 4 Control Register */ -#define MX1_RSSR4 __REG(0x00209190) /* Channel 4 Request Source Select Register */ -#define MX1_BLR4 __REG(0x00209194) /* Channel 4 Burst Length Register */ -#define MX1_RTOR4 __REG(0x00209198) /* Channel 4 Request Time-Out Register */ -#define MX1_BUCR4 __REG(0x00209198) /* Channel 4 Bus Utilization Control Register */ - -/* Channel 5 */ - -#define MX1_SAR5 __REG(0x002091C0) /* Channel 5 Source Address Register */ -#define MX1_DAR5 __REG(0x002091C4) /* Channel 5 Destination Address Register */ -#define MX1_CNTR5 __REG(0x002091C8) /* Channel 5 Count Register */ -#define MX1_CCR5 __REG(0x002091CC) /* Channel 5 Control Register */ -#define MX1_RSSR5 __REG(0x002091D0) /* Channel 5 Request Source Select Register */ -#define MX1_BLR5 __REG(0x002091D4) /* Channel 5 Burst Length Register */ -#define MX1_RTOR5 __REG(0x002091D8) /* Channel 5 Request Time-Out Register */ -#define MX1_BUCR5 __REG(0x002091D8) /* Channel 5 Bus Utilization Control Register */ - -/* Channel 6 */ - -#define MX1_SAR6 __REG(0x00209200) /* Channel 6 Source Address Register */ -#define MX1_DAR6 __REG(0x00209204) /* Channel 6 Destination Address Register */ -#define MX1_CNTR6 __REG(0x00209208) /* Channel 6 Count Register */ -#define MX1_CCR6 __REG(0x0020920C) /* Channel 6 Control Register */ -#define MX1_RSSR6 __REG(0x00209210) /* Channel 6 Request Source Select Register */ -#define MX1_BLR6 __REG(0x00209214) /* Channel 6 Burst Length Register */ -#define MX1_RTOR6 __REG(0x00209218) /* Channel 6 Request Time-Out Register */ -#define MX1_BUCR6 __REG(0x00209218) /* Channel 6 Bus Utilization Control Register */ - -/* Channel 7 */ - -#define MX1_SAR7 __REG(0x00209240) /* Channel 7 Source Address Register */ -#define MX1_DAR7 __REG(0x00209244) /* Channel 7 Destination Address Register */ -#define MX1_CNTR7 __REG(0x00209248) /* Channel 7 Count Register */ -#define MX1_CCR7 __REG(0x0020924C) /* Channel 7 Control Register */ -#define MX1_RSSR7 __REG(0x00209250) /* Channel 7 Request Source Select Register */ -#define MX1_BLR7 __REG(0x00209254) /* Channel 7 Burst Length Register */ -#define MX1_RTOR7 __REG(0x00209258) /* Channel 7 Request Time-Out Register */ -#define MX1_BUCR7 __REG(0x00209258) /* Channel 7 Bus Utilization Control Register */ - -/* Channel 8 */ - -#define MX1_SAR8 __REG(0x00209280) /* Channel 8 Source Address Register */ -#define MX1_DAR8 __REG(0x00209284) /* Channel 8 Destination Address Register */ -#define MX1_CNTR8 __REG(0x00209288) /* Channel 8 Count Register */ -#define MX1_CCR8 __REG(0x0020928C) /* Channel 8 Control Register */ -#define MX1_RSSR8 __REG(0x00209290) /* Channel 8 Request Source Select Register */ -#define MX1_BLR8 __REG(0x00209294) /* Channel 8 Burst Length Register */ -#define MX1_RTOR8 __REG(0x00209298) /* Channel 8 Request Time-Out Register */ -#define MX1_BUCR8 __REG(0x00209298) /* Channel 8 Bus Utilization Control Register */ - -/* Channel 9 */ - -#define MX1_SAR9 __REG(0x002092C0) /* Channel 9 Source Address Register */ -#define MX1_DAR9 __REG(0x002092C4) /* Channel 9 Destination Address Register */ -#define MX1_CNTR9 __REG(0x002092C8) /* Channel 9 Count Register */ -#define MX1_CCR9 __REG(0x002092CC) /* Channel 9 Control Register */ -#define MX1_RSSR9 __REG(0x002092D0) /* Channel 9 Request Source Select Register */ -#define MX1_BLR9 __REG(0x002092D4) /* Channel 9 Burst Length Register */ -#define MX1_RTOR9 __REG(0x002092D8) /* Channel 9 Request Time-Out Register */ -#define MX1_BUCR9 __REG(0x002092D8) /* Channel 9 Bus Utilization Control Register */ - -/* Channel 10 */ - -#define MX1_SAR10 __REG(0x00209300) /* Channel 10 Source Address Register */ -#define MX1_DAR10 __REG(0x00209304) /* Channel 10 Destination Address Register */ -#define MX1_CNTR10 __REG(0x00209308) /* Channel 10 Count Register */ -#define MX1_CCR10 __REG(0x0020930C) /* Channel 10 Control Register */ -#define MX1_RSSR10 __REG(0x00209310) /* Channel 10 Request Source Select Register */ -#define MX1_BLR10 __REG(0x00209314) /* Channel 10 Burst Length Register */ -#define MX1_RTOR10 __REG(0x00209318) /* Channel 10 Request Time-Out Register */ -#define MX1_BUCR10 __REG(0x00209318) /* Channel 10 Bus Utilization Control Register */ - -#define MX1_TCR __REG(0x00209340) /* Test Control Register */ -#define MX1_TFIFOAR __REG(0x00209344) /* Test FIFO A Register */ -#define MX1_TDRR __REG(0x00209348) /* Test DMA Request Register */ -#define MX1_TDIPR __REG(0x0020934C) /* Test DMA In Progress Register */ -#define MX1_TFIFOBR __REG(0x00209350) /* Test FIFO B Register */ - -/* - * MX1 SIM registers - */ - -#define MX1_PORT_CNTL __REG(0x00211000) /* Port Control Register */ -#define MX1_CNTL __REG(0x00211004) /* Control Register */ -#define MX1_RCV_THRESHOLD __REG(0x00211008)/* Receive Threshold Register */ -#define MX1_ENABLE __REG(0x0021100C) /* Transmit/Receive Enable Register */ -#define MX1_XMT_STATUS __REG(0x00211010) /* Transmit Status Register */ -#define MX1_RCV_STATUS __REG(0x00211014) /* Receive Status Register */ -#define MX1_SIM_INT_MASK __REG(0x00211018) /* Interrupt Mask Register */ -#define MX1_XMT_BUF __REG(0x0021101C) /* Port Transmit Buffer Register */ -#define MX1_RCV_BUF __REG(0x00211020) /* Receive Buffer Register */ -#define MX1_PORT_DETECT __REG(0x00211024) /* Detect Register */ -#define MX1_XMT_THRESHOLD __REG(0x00211028)/* Transmit Threshold Register */ -#define MX1_GUARD_CNTL __REG(0x0021102C) /* Transmit Guard Control Register */ -#define MX1_OD_CONFIG __REG(0x00211030) /* Open-Drain Configuration Control Register */ -#define MX1_RESET_CNTL __REG(0x00211034) /* Reset Control Register */ -#define MX1_CHAR_WAIT __REG(0x00211038) /* Charactor Wait Timer Register */ -#define MX1_GPCNT __REG(0x0021103C) /* General Purpose Counter Register */ -#define MX1_DIVISOR __REG(0x00211040) /* Divisor Register */ - -/* - * MX1 USBD registers - */ - -#define MX1_USB_FRAME __REG(0x00212000) /* USB Frame Number and Match Register */ -#define MX1_USB_SPEC __REG(0x00212004) /* USB Spec & Release Number Register */ -#define MX1_USB_STAT __REG(0x00212008) /* USB Status Register */ -#define MX1_USB_CTRL __REG(0x0021200C) /* USB Control Register */ -#define MX1_USB_DADR __REG(0x00212010) /* USB Descriptor RAM Address Register */ -#define MX1_USB_DDAT __REG(0x00212014) /* USB Descriptor RAM/Endpoint buffer Data Register */ -#define MX1_USB_INTR __REG(0x00212018) /* USB Interrupt Status Register */ -#define MX1_USB_MASK __REG(0x0021201C) /* USB Interrupt Mask Register */ -#define MX1_USB_ENAB __REG(0x00212024) /* USB Enable Register */ - -/* Endpoint 0 */ -#define MX1_USB_EP0_STAT __REG(0x00212030) /* Endpoint 0 Status/Control Register */ -#define MX1_USB_EP0_INTR __REG(0x00212034) /* Endpoint 0 Interrupt Status Register */ -#define MX1_USB_EP0_MASK __REG(0x00212038) /* Endpoint 0 Interrupt Mask Register */ -#define MX1_USB_EP0_FDAT __REG(0x0021203C) /* Endpoint 0 FIFO Data Register */ -#define MX1_USB_EP0_FSTAT __REG(0x00212040) /* Endpoint 0 FIFO Status Register */ -#define MX1_USB_EP0_FCTRL __REG(0x00212044) /* Endpoint 0 FIFO Control Register */ -#define MX1_USB_EP0_LRFP __REG(0x00212048) /* Endpoint 0 Last Read Frame Pointer Register */ -#define MX1_USB_EP0_LWFP __REG(0x0021204C) /* Endpoint 0 Last Write Frame Pointer Register */ -#define MX1_USB_EP0_FALRM __REG(0x00212050) /* Endpoint 0 FIFO Alarm Register */ -#define MX1_USB_EP0_FRDP __REG(0x00212054) /* Endpoint 0 FIFO Read Pointer Register */ -#define MX1_USB_EP0_FWRP __REG(0x00212058) /* Endpoint 0 FIFO Write Pointer Register */ - -/* Endpoint 1 */ -#define MX1_USB_EP1_STAT __REG(0x00212060) /* Endpoint 1 Status/Control Register */ -#define MX1_USB_EP1_INTR __REG(0x00212064) /* Endpoint 1 Interrupt Status Register */ -#define MX1_USB_EP1_MASK __REG(0x00212068) /* Endpoint 1 Interrupt Mask Register */ -#define MX1_USB_EP1_FDAT __REG(0x0021206C) /* Endpoint 1 FIFO Data Register */ -#define MX1_USB_EP1_FSTAT __REG(0x00212070) /* Endpoint 1 FIFO Status Register */ -#define MX1_USB_EP1_FCTRL __REG(0x00212074) /* Endpoint 1 FIFO Control Register */ -#define MX1_USB_EP1_LRFP __REG(0x00212078) /* Endpoint 1 Last Read Frame Pointer Register */ -#define MX1_USB_EP1_LWFP __REG(0x0021207C) /* Endpoint 1 Last Write Frame Pointer Register */ -#define MX1_USB_EP1_FALRM __REG(0x00212080) /* Endpoint 1 FIFO Alarm Register */ -#define MX1_USB_EP1_FRDP __REG(0x00212084) /* Endpoint 1 FIFO Read Pointer Register */ -#define MX1_USB_EP1_FWRP __REG(0x00212088) /* Endpoint 1 FIFO Write Pointer Register */ - -/* Endpoint 2 */ -#define MX1_USB_EP2_STAT __REG(0x00212090) /* Endpoint 2 Status/Control Register */ -#define MX1_USB_EP2_INTR __REG(0x00212094) /* Endpoint 2 Interrupt Status Register */ -#define MX1_USB_EP2_MASK __REG(0x00212098) /* Endpoint 2 Interrupt Mask Register */ -#define MX1_USB_EP2_FDAT __REG(0x0021209C) /* Endpoint 2 FIFO Data Register */ -#define MX1_USB_EP2_FSTAT __REG(0x002120A0) /* Endpoint 2 FIFO Status Register */ -#define MX1_USB_EP2_FCTRL __REG(0x002120A4) /* Endpoint 2 FIFO Control Register */ -#define MX1_USB_EP2_LRFP __REG(0x002120A8) /* Endpoint 2 Last Read Frame Pointer Register */ -#define MX1_USB_EP2_LWFP __REG(0x002120AC) /* Endpoint 2 Last Write Frame Pointer Register */ -#define MX1_USB_EP2_FALRM __REG(0x002120B0) /* Endpoint 2 FIFO Alarm Register */ -#define MX1_USB_EP2_FRDP __REG(0x002120B4) /* Endpoint 2 FIFO Read Pointer Register */ -#define MX1_USB_EP2_FWRP __REG(0x002120B8) /* Endpoint 2 FIFO Write Pointer Register */ - -/* Endpoint 3 */ -#define MX1_USB_EP3_STAT __REG(0x002120C0) /* Endpoint 3 Status/Control Register */ -#define MX1_USB_EP3_INTR __REG(0x002120C4) /* Endpoint 3 Interrupt Status Register */ -#define MX1_USB_EP3_MASK __REG(0x002120C8) /* Endpoint 3 Interrupt Mask Register */ -#define MX1_USB_EP3_FDAT __REG(0x002120CC) /* Endpoint 3 FIFO Data Register */ -#define MX1_USB_EP3_FSTAT __REG(0x002120D0) /* Endpoint 3 FIFO Status Register */ -#define MX1_USB_EP3_FCTRL __REG(0x002120D4) /* Endpoint 3 FIFO Control Register */ -#define MX1_USB_EP3_LRFP __REG(0x002120D8) /* Endpoint 3 Last Read Frame Pointer Register */ -#define MX1_USB_EP3_LWFP __REG(0x002120DC) /* Endpoint 3 Last Write Frame Pointer Register */ -#define MX1_USB_EP3_FALRM __REG(0x002120E0) /* Endpoint 3 FIFO Alarm Register */ -#define MX1_USB_EP3_FRDP __REG(0x002120E4) /* Endpoint 3 FIFO Read Pointer Register */ -#define MX1_USB_EP3_FWRP __REG(0x002120E8) /* Endpoint 3 FIFO Write Pointer Register */ - -/* Endpoint 4 */ -#define MX1_USB_EP4_STAT __REG(0x002120F0) /* Endpoint 4 Status/Control Register */ -#define MX1_USB_EP4_INTR __REG(0x002120F4) /* Endpoint 4 Interrupt Status Register */ -#define MX1_USB_EP4_MASK __REG(0x002120F8) /* Endpoint 4 Interrupt Mask Register */ -#define MX1_USB_EP4_FDAT __REG(0x002120FC) /* Endpoint 4 FIFO Data Register */ -#define MX1_USB_EP4_FSTAT __REG(0x00212100) /* Endpoint 4 FIFO Status Register */ -#define MX1_USB_EP4_FCTRL __REG(0x00212104) /* Endpoint 4 FIFO Control Register */ -#define MX1_USB_EP4_LRFP __REG(0x00212108) /* Endpoint 4 Last Read Frame Pointer Register */ -#define MX1_USB_EP4_LWFP __REG(0x0021210C) /* Endpoint 4 Last Write Frame Pointer Register */ -#define MX1_USB_EP4_FALRM __REG(0x00212110) /* Endpoint 4 FIFO Alarm Register */ -#define MX1_USB_EP4_FRDP __REG(0x00212114) /* Endpoint 4 FIFO Read Pointer Register */ -#define MX1_USB_EP4_FWRP __REG(0x00212118) /* Endpoint 4 FIFO Write Pointer Register */ - -/* Endpoint 5 */ -#define MX1_USB_EP5_STAT __REG(0x00212120) /* Endpoint 5 Status/Control Register */ -#define MX1_USB_EP5_INTR __REG(0x00212124) /* Endpoint 5 Interrupt Status Register */ -#define MX1_USB_EP5_MASK __REG(0x00212128) /* Endpoint 5 Interrupt Mask Register */ -#define MX1_USB_EP5_FDAT __REG(0x0021212C) /* Endpoint 5 FIFO Data Register */ -#define MX1_USB_EP5_FSTAT __REG(0x00212130) /* Endpoint 5 FIFO Status Register */ -#define MX1_USB_EP5_FCTRL __REG(0x00212134) /* Endpoint 5 FIFO Control Register */ -#define MX1_USB_EP5_LRFP __REG(0x00212138) /* Endpoint 5 Last Read Frame Pointer Register */ -#define MX1_USB_EP5_LWFP __REG(0x0021213C) /* Endpoint 5 Last Write Frame Pointer Register */ -#define MX1_USB_EP5_FALRM __REG(0x00212140) /* Endpoint 5 FIFO Alarm Register */ -#define MX1_USB_EP5_FRDP __REG(0x00212144) /* Endpoint 5 FIFO Read Pointer Register */ -#define MX1_USB_EP5_FWRP __REG(0x00212148) /* Endpoint 5 FIFO Write Pointer Register */ - -/* - * MX1 SPI 1 registers - */ -#define MX1_RXDATAREG1 __REG(0x00213000) /* SPI 1 Rx Data Register */ -#define MX1_TXDATAREG1 __REG(0x00213004) /* SPI 1 Tx Data Register */ -#define MX1_CONTROLREG1 __REG(0x00213008) /* SPI 1 Control Register */ -#define MX1_INTREG1 __REG(0x0021300C) /* SPI 1 Interrupt Control/Status Register */ -#define MX1_TESTREG1 __REG(0x00213010) /* SPI 1 Test Register */ -#define MX1_PERIODREG1 __REG(0x00213014) /* SPI 1 Sample Period Control Register */ -#define MX1_DMAREG1 __REG(0x00213018) /* SPI 1 DMA Control Register */ -#define MX1_RESETREG1 __REG(0x00213018) /* SPI 1 Soft Reset Register */ - -/* - * MX1 MMC/SDHC registers - */ -#define MX1_STR_STP_CLK __REG(0x00214000) /* MMC/SD Clock Control Register */ -#define MX1_STATUS __REG(0x00214004) /* MMC/SD Status Register */ -#define MX1_CLK_RATE __REG(0x00214008) /* MMC/SD Clock Rate Register */ -#define MX1_CMD_DAT_CONT __REG(0x0021400C) /* MMC/SD Command & Data Control Register */ -#define MX1_RES_TO __REG(0x00214010) /* MMC/SD Response Time Out Register */ -#define MX1_READ_TO __REG(0x00214014) /* MMC/SD Read Time Out Register */ -#define MX1_BLK_LEN __REG(0x00214018) /* MMC/SD Block Length Register */ -#define MX1_NOB __REG(0x0021401C) /* MMC/SD Number of Block Register */ -#define MX1_REV_NO __REG(0x00214020) /* MMC/SD Revision Number Register */ -#define MX1_MMC_INT_MASK __REG(0x00214024) /* MMC/SD Interrupt Mask Register */ -#define MX1_CMD __REG(0x00214028) /* MMC/SD Command Number Register */ -#define MX1_ARGH __REG(0x0021402C) /* MMC/SD Higher Argument Register */ -#define MX1_ARGL __REG(0x00214030) /* MMC/SD Lower Argument Register */ -#define MX1_RES_FIFO __REG(0x00214034) /* MMC/SD Response FIFO Register */ -#define MX1_BUFFER_ACCESS __REG(0x00214038) /* MMC/SD Buffer Access Register */ - -/* - * MX1 ASP registers - */ -#define MX1_ASP_PADFIFO __REG(0x00215000) /* Pen Sample FIFO */ -#define MX1_ASP_VADFIFO __REG(0x00215004) /* Voice ADC Register */ -#define MX1_ASP_VDAFIFO __REG(0x00215008) /* Voice DAC Register */ -#define MX1_ASP_VADCOEF __REG(0x0021500C) /* Voice ADC FIR Coefficients RAM */ -#define MX1_ASP_ACNTLCR __REG(0x00215010) /* Control Register */ -#define MX1_ASP_PSMPLRG __REG(0x00215014) /* Pen A/D Sample Rate Control Register */ -#define MX1_ASP_ICNTLR __REG(0x00215018) /* Interrupt Control Register */ -#define MX1_ASP_ISTATR __REG(0x0021501C) /* Interrupt/Error Status Register */ -#define MX1_ASP_VADGAIN __REG(0x00215020) /* Voice ADC Control Register */ -#define MX1_ASP_VDAGAIN __REG(0x00215024) /* Voice DAC Control Register */ -#define MX1_ASP_VDACOEF __REG(0x00215028) /* Voice DAC FIR Coefficients RAM */ -#define MX1_ASP_CLKDIV __REG(0x0021502C) /* Clock Divide Register */ -#define MX1_ASP_CMPCNTL __REG(0x0021502C) /* Compare Control Register */ - -/* - * MX1 BTA registers - */ - -/* - * MX1 I2C registers - */ -#define MX1_IADR __REG(0x00217000) /* I2C Address Register */ -#define MX1_IFDR __REG(0x00217004) /* I2C Frequency Divider Register */ -#define MX1_I2CR __REG(0x00217008) /* I2C Control Register */ -#define MX1_I2CSR __REG(0x0021700C) /* I2C Status Register */ -#define MX1_I2DR __REG(0x00217010) /* I2C Data I/O Register */ - -/* - * MX1 SSI registers - */ -#define MX1_STX __REG(0x00218000) /* SSI Transmit Data Register */ -#define MX1_SRX __REG(0x00218004) /* SSI Receive Data Register */ -#define MX1_SCSR __REG(0x00218008) /* SSI Control/Status Register */ -#define MX1_STCR __REG(0x0021800C) /* SSI Transmit Configuration Register */ -#define MX1_SRCR __REG(0x00218010) /* SSI Recieve Configuration Register */ -#define MX1_STCCR __REG(0x00218014) /* SSI Transmit Clock Control Register */ -#define MX1_SRCCR __REG(0x00218018) /* SSI Receive Clock Control Register */ -#define MX1_STSR __REG(0x0021801C) /* SSI Time Slot Register */ -#define MX1_SFCSR __REG(0x00218020) /* SSI FIFO Control/Status Register */ -#define MX1_SOR __REG(0x00218024) /* SSI Option Register */ - -/* - * MX1 SPI 2 registers - */ -#define MX1_RXDATAREG2 __REG(0x00219000) /* SPI 2 Rx Data Register */ -#define MX1_TXDATAREG2 __REG(0x00219004) /* SPI 2 Tx Data Register */ -#define MX1_CONTROLREG2 __REG(0x00219008) /* SPI 2 Control Register */ -#define MX1_INTREG2 __REG(0x0021900C) /* SPI 2 Interrupt Control/Status Register */ -#define MX1_TESTREG2 __REG(0x00219010) /* SPI 2 Test Register */ -#define MX1_PERIODREG2 __REG(0x00219014) /* SPI 2 Sample Period Control Register */ -#define MX1_DMAREG2 __REG(0x00219018) /* SPI 2 DMA Control Register */ -#define MX1_RESETREG2 __REG(0x00219018) /* SPI 2 Soft Reset Register */ - -/* - * MX1 MSHC registers - */ -#define MX1_MSCMD __REG(0x0021A000) /* Memory Stick Command Register */ -#define MX1_MSCS __REG(0x0021A002) /* Memory Stick Control/Status Register */ -#define MX1_MSTDATA __REG(0x0021A004) /* Memory Stick Transmit FIFO Data Register */ -#define MX1_MSRDATA __REG(0x0021A004) /* Memory Stick Recieve FIFO Data Register */ -#define MX1_MSICS __REG(0x0021A006) /* Memory Stick Interrupt Control/Status Register */ -#define MX1_MSPPCD __REG(0x0021A008) /* Memory Stick Parallel Port Control/Data Register */ -#define MX1_MSC2 __REG(0x0021A00A) /* Memory Stick Control 2 Register */ -#define MX1_MSACD __REG(0x0021A00C) /* Memory Stick Auto Command Register */ -#define MX1_MSFAECS __REG(0x0021A00E) /* Memory Stick FIFO Access Error Control/Status Register */ -#define MX1_MSCLKD __REG(0x0021A010) /* Memory Stick Serial Clock divider Register */ -#define MX1_MSDRQC __REG(0x0021A012) /* Memory Stick DMA Request Control Register */ - -/* - * MX1 PLLCLK registers - */ -#define MX1_CSCR __REG(0x0021B000) /* Clock Source Control Register */ -#define MX1_MPCTL0 __REG(0x0021B004) /* MCU PLL Control Register 0 */ -#define MX1_MPCTL1 __REG(0x0021B008) /* MCU PLL & System Clock Control Register 1 */ -#define MX1_UPCTL0 __REG(0x0021B00C) /* USB PLL Control Register 0 */ -#define MX1_UPCTL1 __REG(0x0021B010) /* USB PLL Control Register 1 */ -#define MX1_PCDR __REG(0x0021B020) /* Peripheral Clock Divider Register */ - -/* - * MX1 RESET registers - */ -#define MX1_RSR __REG(0x0021B800) /* Reset Source Register */ - -/* - * MX1 SYS CTRL registers - */ -#define MX1_SIDR __REG(0x0021B804) /* Silicon ID Register */ -#define MX1_FMCR __REG(0x0021B808) /* Function MultiPlexing Control Register */ -#define MX1_GPCR __REG(0x0021B80C) /* Global Peripheral Control Register */ - -/* - * MX1 GPIO registers - */ - -/* Port A */ -#define MX1_DDIR_A __REG(0x0021C000) /* Port A Data Direction Register */ -#define MX1_OCR1_A __REG(0x0021C004) /* Port A Output Configuration Register 1 */ -#define MX1_OCR2_A __REG(0x0021C008) /* Port A Output Configuration Register 2 */ -#define MX1_ICONFA1_A __REG(0x0021C00C) /* Port A Input Configuration Register A1 */ -#define MX1_ICONFA2_A __REG(0x0021C010) /* Port A Input Configuration Register A2 */ -#define MX1_ICONFB1_A __REG(0x0021C014) /* Port A Input Configuration Register B1 */ -#define MX1_ICONFB2_A __REG(0x0021C018) /* Port A Input Configuration Register B2 */ -#define MX1_DR_A __REG(0x0021C01C) /* Port A Data Register */ -#define MX1_GIUS_A __REG(0x0021C020) /* Port A GPIO In Use Register */ -#define MX1_SSR_A __REG(0x0021C024) /* Port A Sample Status Register */ -#define MX1_ICR1_A __REG(0x0021C028) /* Port A Interrupt Configuration Register 1 */ -#define MX1_ICR2_A __REG(0x0021C02C) /* Port A Interrupt Configuration Register 2 */ -#define MX1_IMR_A __REG(0x0021C030) /* Port A Interrupt Mask Register */ -#define MX1_ISR_A __REG(0x0021C034) /* Port A Interrupt Status Register */ -#define MX1_GPR_A __REG(0x0021C038) /* Port A General Purpose Register */ -#define MX1_SWR_A __REG(0x0021C03C) /* Port A Software Reset Register */ -#define MX1_PUEN_A __REG(0x0021C040) /* Port A Pull Up Enable Register */ - -/* Port B */ -#define MX1_DDIR_B __REG(0x0021C100) /* Port B Data Direction Register */ -#define MX1_OCR1_B __REG(0x0021C104) /* Port B Output Configuration Register 1 */ -#define MX1_OCR2_B __REG(0x0021C108) /* Port B Output Configuration Register 2 */ -#define MX1_ICONFA1_B __REG(0x0021C10C) /* Port B Input Configuration Register A1 */ -#define MX1_ICONFA2_B __REG(0x0021C110) /* Port B Input Configuration Register A2 */ -#define MX1_ICONFB1_B __REG(0x0021C114) /* Port B Input Configuration Register B1 */ -#define MX1_ICONFB2_B __REG(0x0021C118) /* Port B Input Configuration Register B2 */ -#define MX1_DR_B __REG(0x0021C11C) /* Port B Data Register */ -#define MX1_GIUS_B __REG(0x0021C120) /* Port B GPIO In Use Register */ -#define MX1_SSR_B __REG(0x0021C124) /* Port B Sample Status Register */ -#define MX1_ICR1_B __REG(0x0021C128) /* Port B Interrupt Configuration Register 1 */ -#define MX1_ICR2_B __REG(0x0021C12C) /* Port B Interrupt Configuration Register 2 */ -#define MX1_IMR_B __REG(0x0021C130) /* Port B Interrupt Mask Register */ -#define MX1_ISR_B __REG(0x0021C134) /* Port B Interrupt Status Register */ -#define MX1_GPR_B __REG(0x0021C138) /* Port B General Purpose Register */ -#define MX1_SWR_B __REG(0x0021C13C) /* Port B Software Reset Register */ -#define MX1_PUEN_B __REG(0x0021C140) /* Port B Pull Up Enable Register */ - -/* Port C */ -#define MX1_DDIR_C __REG(0x0021C200) /* Port C Data Direction Register */ -#define MX1_OCR1_C __REG(0x0021C204) /* Port C Output Configuration Register 1 */ -#define MX1_OCR2_C __REG(0x0021C208) /* Port C Output Configuration Register 2 */ -#define MX1_ICONFA1_C __REG(0x0021C20C) /* Port C Input Configuration Register A1 */ -#define MX1_ICONFA2_C __REG(0x0021C210) /* Port C Input Configuration Register A2 */ -#define MX1_ICONFB1_C __REG(0x0021C214) /* Port C Input Configuration Register B1 */ -#define MX1_ICONFB2_C __REG(0x0021C218) /* Port C Input Configuration Register B2 */ -#define MX1_DR_C __REG(0x0021C21C) /* Port C Data Register */ -#define MX1_GIUS_C __REG(0x0021C220) /* Port C GPIO In Use Register */ -#define MX1_SSR_C __REG(0x0021C224) /* Port C Sample Status Register */ -#define MX1_ICR1_C __REG(0x0021C228) /* Port C Interrupt Configuration Register 1 */ -#define MX1_ICR2_C __REG(0x0021C22C) /* Port C Interrupt Configuration Register 2 */ -#define MX1_IMR_C __REG(0x0021C230) /* Port C Interrupt Mask Register */ -#define MX1_ISR_C __REG(0x0021C234) /* Port C Interrupt Status Register */ -#define MX1_GPR_C __REG(0x0021C238) /* Port C General Purpose Register */ -#define MX1_SWR_C __REG(0x0021C23C) /* Port C Software Reset Register */ -#define MX1_PUEN_C __REG(0x0021C240) /* Port C Pull Up Enable Register */ - -/* Port D */ -#define MX1_DDIR_D __REG(0x0021C300) /* Port D Data Direction Register */ -#define MX1_OCR1_D __REG(0x0021C304) /* Port D Output Configuration Register 1 */ -#define MX1_OCR2_D __REG(0x0021C308) /* Port D Output Configuration Register 2 */ -#define MX1_ICONFA1_D __REG(0x0021C30C) /* Port D Input Configuration Register A1 */ -#define MX1_ICONFA2_D __REG(0x0021C310) /* Port D Input Configuration Register A2 */ -#define MX1_ICONFB1_D __REG(0x0021C314) /* Port D Input Configuration Register B1 */ -#define MX1_ICONFB2_D __REG(0x0021C318) /* Port D Input Configuration Register B2 */ -#define MX1_DR_D __REG(0x0021C31C) /* Port D Data Register */ -#define MX1_GIUS_D __REG(0x0021C320) /* Port D GPIO In Use Register */ -#define MX1_SSR_D __REG(0x0021C324) /* Port D Sample Status Register */ -#define MX1_ICR1_D __REG(0x0021C328) /* Port D Interrupt Configuration Register 1 */ -#define MX1_ICR2_D __REG(0x0021C32C) /* Port D Interrupt Configuration Register 2 */ -#define MX1_IMR_D __REG(0x0021C330) /* Port D Interrupt Mask Register */ -#define MX1_ISR_D __REG(0x0021C334) /* Port D Interrupt Status Register */ -#define MX1_GPR_D __REG(0x0021C338) /* Port D General Purpose Register */ -#define MX1_SWR_D __REG(0x0021C33C) /* Port D Software Reset Register */ -#define MX1_PUEN_D __REG(0x0021C340) /* Port D Pull Up Enable Register */ - -/* - * MX1 EIM registers - */ -#define MX1_CS0U __REG(0x00220000) /* Chip Select 0 Upper Control Register */ -#define MX1_CS0L __REG(0x00220004) /* Chip Select 0 Lower Control Register */ -#define MX1_CS1U __REG(0x00220008) /* Chip Select 1 Upper Control Register */ -#define MX1_CS1L __REG(0x0022000C) /* Chip Select 1 Lower Control Register */ -#define MX1_CS2U __REG(0x00220010) /* Chip Select 2 Upper Control Register */ -#define MX1_CS2L __REG(0x00220014) /* Chip Select 2 Lower Control Register */ -#define MX1_CS3U __REG(0x00220018) /* Chip Select 3 Upper Control Register */ -#define MX1_CS3L __REG(0x0022001C) /* Chip Select 3 Lower Control Register */ -#define MX1_CS4U __REG(0x00220020) /* Chip Select 4 Upper Control Register */ -#define MX1_CS4L __REG(0x00220024) /* Chip Select 4 Lower Control Register */ -#define MX1_CS5U __REG(0x00220028) /* Chip Select 5 Upper Control Register */ -#define MX1_CS5L __REG(0x0022002C) /* Chip Select 5 Lower Control Register */ -#define MX1_WEIM __REG(0x00220030) /* weim cONFIGURATION Register */ - -/* - * MX1 SDRAMC registers - */ -#define MX1_SDCTL0 __REG(0x00221000) /* SDRAM 0 Control Register */ -#define MX1_SDCTL1 __REG(0x00221004) /* SDRAM 1 Control Register */ -#define MX1_MISCELLANEOUS __REG(0x00221014) /* Miscellaneous Register */ -#define MX1_SDRST __REG(0x00221018) /* SDRAM Reset Register */ - -/* - * MX1 MMA registers - */ -#define MX1_MMA_MAC_MOD __REG(0x00222000) /* MMA MAC Module Register */ -#define MX1_MMA_MAC_CTRL __REG(0x00222004) /* MMA MAC Control Register */ -#define MX1_MMA_MAC_MULT __REG(0x00222008) /* MMA MAC Multiply Counter Register */ -#define MX1_MMA_MAC_ACCU __REG(0x0022200C) /* MMA MAC Accumulate Counter Register */ -#define MX1_MMA_MAC_INTR __REG(0x00222010) /* MMA MAC Interrupt Register */ -#define MX1_MMA_MAC_INTR_MASK __REG(0x00222014) /* MMA MAC Interrupt Mask Register */ -#define MX1_MMA_MAC_FIFO __REG(0x00222018) /* MMA MAC FIFO Register */ -#define MX1_MMA_MAC_FIFO_STAT __REG(0x0022201C) /* MMA MAC FIFO Status Register */ -#define MX1_MMA_MAC_BURST __REG(0x00222020) /* MMA MAC Burst Count Register */ -#define MX1_MMA_MAC_BITSEL __REG(0x00222024) /* MMA MAC Bit Select Register */ - -#define MX1_MMA_MAC_XBASE __REG(0x00222200) /* MMA MAC X Base Address Register */ -#define MX1_MMA_MAC_XINDEX __REG(0x00222204) /* MMA MAC X Index Register */ -#define MX1_MMA_MAC_XLENGTH __REG(0x00222208) /* MMA MAC X Length Register */ -#define MX1_MMA_MAC_XMODIFY __REG(0x0022220C) /* MMA MAC X Modify Register */ -#define MX1_MMA_MAC_XINCR __REG(0x00222210) /* MMA MAC X Increment Register */ -#define MX1_MMA_MAC_XCOUNT __REG(0x00222214) /* MMA MAC X Count Register */ - -#define MX1_MMA_MAC_YBASE __REG(0x00222300) /* MMA MAC Y Base Address Register */ -#define MX1_MMA_MAC_YINDEX __REG(0x00222304) /* MMA MAC Y Index Register */ -#define MX1_MMA_MAC_YLENGTH __REG(0x00222308) /* MMA MAC Y Length Register */ -#define MX1_MMA_MAC_YMODIFY __REG(0x0022230C) /* MMA MAC Y Modify Register */ -#define MX1_MMA_MAC_YINCR __REG(0x00222310) /* MMA MAC Y Increment Register */ -#define MX1_MMA_MAC_YCOUNT __REG(0x00222314) /* MMA MAC Y Count Register */ - -#define MX1_MMA_DCTCTRL __REG(0x00222400) /* DCT/iDCT Control Register */ -#define MX1_MMA_DCTVERSION __REG(0x00222404) /* DCT/iDCT Version Register */ -#define MX1_MMA_DCTIRQENA __REG(0x00222408) /* DCT/iDCT IRQ Enable Register */ -#define MX1_MMA_DCTIRQSTAT __REG(0x0022240C) /* DCT/iDCT IRQ Status Register */ -#define MX1_MMA_DCTSRCDATA __REG(0x00222410) /* DCT/iDCT Source Data Address */ -#define MX1_MMA_DCTDESDATA __REG(0x00222414) /* DCT/iDCT Destination Data Address */ -#define MX1_MMA_DCTXOFF __REG(0x00222418) /* DCT/iDCT X-Offset Address */ -#define MX1_MMA_DCTYOFF __REG(0x0022241C) /* DCT/iDCT Y-Offset Address */ -#define MX1_MMA_DCTXYCNT __REG(0x00222420) /* DCT/iDCT XY Count */ -#define MX1_MMA_DCTSKIP __REG(0x00222424) /* DCT/iDCT Skip Address */ -#define MX1_MMA_DCTFIFO __REG(0x00222500) /* DCT/iDCT Data FIFO */ - -/* - * MX1 AITC registers - */ -#define MX1_INTCNTL __REG(0x00223000) /* Interrupt Control Register */ -#define MX1_NIMASK __REG(0x00223004) /* Normal Interrupt Mask Register */ -#define MX1_INTENNUM __REG(0x00223008) /* Interrupt Enable Number Register */ -#define MX1_INTDISNUM __REG(0x0022300C) /* Interrupt Disable Number Register */ -#define MX1_INTENABLEH __REG(0x00223010) /* Interrupt Enable Register High */ -#define MX1_INTENABLEL __REG(0x00223014) /* Interrupt Enable Register Low */ -#define MX1_INTTYPEH __REG(0x00223018) /* Interrupt Type Register High */ -#define MX1_INTTYPEL __REG(0x0022301C) /* Interrupt Type Register Low */ -#define MX1_NIPRIORITY7 __REG(0x00223020) /* Normal Interrupt Priority Level Register 7*/ -#define MX1_NIPRIORITY6 __REG(0x00223024) /* Normal Interrupt Priority Level Register 6*/ -#define MX1_NIPRIORITY5 __REG(0x00223028) /* Normal Interrupt Priority Level Register 5*/ -#define MX1_NIPRIORITY4 __REG(0x0022302C) /* Normal Interrupt Priority Level Register 4*/ -#define MX1_NIPRIORITY3 __REG(0x00223030) /* Normal Interrupt Priority Level Register 3*/ -#define MX1_NIPRIORITY2 __REG(0x00223034) /* Normal Interrupt Priority Level Register 2*/ -#define MX1_NIPRIORITY1 __REG(0x00223038) /* Normal Interrupt Priority Level Register 1*/ -#define MX1_NIPRIORITY0 __REG(0x0022303C) /* Normal Interrupt Priority Level Register 0*/ -#define MX1_NIVECSR __REG(0x00223040) /* Normal Interrupt Vector & Status Register */ -#define MX1_FIVECSR __REG(0x00223044) /* Fast Interrupt Vector & Status Register */ -#define MX1_INTSRCH __REG(0x00223048) /* Interrupt Source Register High */ -#define MX1_INTSRCL __REG(0x0022304C) /* Interrupt Source Register Low */ -#define MX1_INTFRCH __REG(0x00223050) /* Interrupt Force Register High */ -#define MX1_INTFRCL __REG(0x00223054) /* Interrupt Force Register Low */ -#define MX1_NIPNDH __REG(0x00223058) /* Normal Interrupt Pending Register High */ -#define MX1_NIPNDL __REG(0x0022305C) /* Normal Interrupt Pending Register Low */ -#define MX1_FIPNDH __REG(0x00223060) /* Fast Interrupt Pending Register High */ -#define MX1_FIPNDL __REG(0x00223064) /* Fast Interrupt Pending Register Low */ - -/* - * MX1 CSI registers - */ -#define MX1_CSICR1 __REG(0x00224000) /* CSI Control Register 1 */ -#define MX1_CSICR2 __REG(0x00224004) /* CSI Control Register 2 */ -#define MX1_CSISR __REG(0x00224008) /* CSI Status Register 1 */ -#define MX1_CSISTATR __REG(0x0022400C) /* CSI Statistic FIFO Register 1 */ -#define MX1_CSIRXR __REG(0x00224010) /* CSI RxFIFO Register 1 */ - -#endif /* __MC9328_H__ */ - -#if 0 -/* - MX1 dma definition -*/ - -#define MAX_DMA_ADDRESS 0xffffffff - -/*#define MAX_DMA_CHANNELS 0 */ - -#define MAX_DMA_CHANNELS 11 -#define MAX_DMA_2D_REGSET 2 - -/* MX1 DMA module registers' address */ - -#define MX1_DMA_BASE IO_ADDRESS(0x00209000) -#define MX1_DMA_DCR (MX1_DMA_BASE + 0x00) /* DMA control register */ -#define MX1_DMA_DISR (MX1_DMA_BASE + 0x04) /* DMA interrupt status register */ -#define MX1_DMA_DIMR (MX1_DMA_BASE + 0x08) /* DMA interrupt mask register */ -#define MX1_DMA_DBTOSR (MX1_DMA_BASE + 0x0C) /* DMA burst time-out status register */ -#define MX1_DMA_DRTOSR (MX1_DMA_BASE + 0x10) /* DMA request time-out status register */ -#define MX1_DMA_DSESR (MX1_DMA_BASE + 0x14) /* DMA transfer error status register */ -#define MX1_DMA_DBOSR (MX1_DMA_BASE + 0x18) /* DMA buffer overflow status register */ -#define MX1_DMA_DBTOCR (MX1_DMA_BASE + 0x1C) /* DMA burst time-out control register */ -#define MX1_DMA_WSRA (MX1_DMA_BASE + 0x40) /* W-size register A */ -#define MX1_DMA_XSRA (MX1_DMA_BASE + 0x44) /* X-size register A */ -#define MX1_DMA_YSRA (MX1_DMA_BASE + 0x48) /* Y-size register A */ -#define MX1_DMA_WSRB (MX1_DMA_BASE + 0x4C) /* W-size register B */ -#define MX1_DMA_XSRB (MX1_DMA_BASE + 0x50) /* X-size register B */ -#define MX1_DMA_YSRB (MX1_DMA_BASE + 0x54) /* Y-size register B */ - -#define MX1_DMA_SAR0 (MX1_DMA_BASE + 0x80) /* source address register 0 */ -#define MX1_DMA_DAR0 (MX1_DMA_BASE + 0x84) /* destination address register 0 */ -#define MX1_DMA_CNTR0 (MX1_DMA_BASE + 0x88) /* count register 0 */ -#define MX1_DMA_CCR0 (MX1_DMA_BASE + 0x8C) /* channel control register 0 */ -#define MX1_DMA_RSSR0 (MX1_DMA_BASE + 0x90) /* request source select register 0 */ -#define MX1_DMA_BLR0 (MX1_DMA_BASE + 0x94) /* burst length register 0 */ -#define MX1_DMA_RTOR0 (MX1_DMA_BASE + 0x98) /* request time-out register 0 */ -#define MX1_DMA_BUCR0 (MX1_DMA_BASE + 0x98) /* bus utilization control register 0 */ - -/* register set 1 to 10 are offseted by 0x40 each = 0x10 pointers away */ - -#define DMA_REG_SET_OFS 0x10 - -/* MX1 DMA module registers */ -#define _reg_DMA_DCR (*((P_VU32)MX1_DMA_DCR)) -#define _reg_DMA_DISR (*((P_VU32)MX1_DMA_DISR)) -#define _reg_DMA_DIMR (*((P_VU32)MX1_DMA_DIMR)) -#define _reg_DMA_DBTOSR (*((P_VU32)MX1_DMA_DBTOSR)) -#define _reg_DMA_DRTOSR (*((P_VU32)MX1_DMA_DRTOSR)) -#define _reg_DMA_DSESR (*((P_VU32)MX1_DMA_DSESR)) -#define _reg_DMA_DBOSR (*((P_VU32)MX1_DMA_DBOSR)) -#define _reg_DMA_DBTOCR (*((P_VU32)MX1_DMA_DBTOCR)) -#define _reg_DMA_WSRA (*((P_VU32)MX1_DMA_WSRA)) -#define _reg_DMA_XSRA (*((P_VU32)MX1_DMA_XSRA)) -#define _reg_DMA_YSRA (*((P_VU32)MX1_DMA_YSRA)) -#define _reg_DMA_WSRB (*((P_VU32)MX1_DMA_WSRB)) -#define _reg_DMA_XSRB (*((P_VU32)MX1_DMA_XSRB)) -#define _reg_DMA_YSRB (*((P_VU32)MX1_DMA_YSRB)) -#define _reg_DMA_SAR0 (*((P_VU32)MX1_DMA_SAR0)) -#define _reg_DMA_DAR0 (*((P_VU32)MX1_DMA_DAR0)) -#define _reg_DMA_CNTR0 (*((P_VU32)MX1_DMA_CNTR0)) -#define _reg_DMA_CCR0 (*((P_VU32)MX1_DMA_CCR0)) -#define _reg_DMA_RSSR0 (*((P_VU32)MX1_DMA_RSSR0)) -#define _reg_DMA_BLR0 (*((P_VU32)MX1_DMA_BLR0)) -#define _reg_DMA_RTOR0 (*((P_VU32)MX1_DMA_RTOR0)) -#define _reg_DMA_BUCR0 (*((P_VU32)MX1_DMA_BUCR0)) - -/* DMA error type definition */ -#define MX1_DMA_ERR_BTO 0 /* burst time-out */ -#define MX1_DMA_ERR_RTO 1 /* request time-out */ -#define MX1_DMA_ERR_TE 2 /* transfer error */ -#define MX1_DMA_ERR_BO 3 /* buffer overflow */ - -/* Embedded SRAM */ - -#define MX1_SRAM_BASE 0x00300000 -#define MX1_SRAM_SIZE 0x00020000 - -#define - -#define MX1ADS_SFLASH_BASE 0x0C000000 -#define MX1ADS_SFLASH_SIZE SZ_16M - -#define MX1ADS_IO_BASE 0x00200000 -#define MX1ADS_IO_SIZE SZ_256K - -#define MX1ADS_VID_BASE 0x00300000 -#define MX1ADS_VID_SIZE 0x26000 - -#define MX1ADS_VID_START IO_ADDRESS(MX1ADS_VID_BASE) - -#define MX1_GPIO_BASE 0x0021C000 /* GPIO */ -#define MX1_EXT_UART_BASE 0x15000000 /* external UART */ -#define MX1_TMR1_BASE 0x00202000 /* Timer1 */ -#define MX1ADS_FLASH_BASE 0x0C000000 /* sync FLASH */ -#define MX1_ESRAM_BASE 0x00300000 /* embedded SRAM */ -#define MX1ADS_SDRAM_DISK_BASE 0x0B000000 /* SDRAM disk base (last 16M of SDRAM) */ - -/* ------------------------------------------------------------------------ - * Motorola MX1 system registers - * ------------------------------------------------------------------------ - * - */ - -/* - * Register offests. - * - */ - -#define MX1ADS_AIPI1_OFFSET 0x00000 -#define MX1ADS_WDT_OFFSET 0x01000 -#define MX1ADS_TIM1_OFFSET 0x02000 -#define MX1ADS_TIM2_OFFSET 0x03000 -#define MX1ADS_RTC_OFFSET 0x04000 -#define MX1ADS_LCDC_OFFSET 0x05000 -#define MX1ADS_UART1_OFFSET 0x06000 -#define MX1ADS_UART2_OFFSET 0x07000 -#define MX1ADS_PWM_OFFSET 0x08000 -#define MX1ADS_DMAC_OFFSET 0x09000 -#define MX1ADS_AIPI2_OFFSET 0x10000 -#define MX1ADS_SIM_OFFSET 0x11000 -#define MX1ADS_USBD_OFFSET 0x12000 -#define MX1ADS_SPI1_OFFSET 0x13000 -#define MX1ADS_MMC_OFFSET 0x14000 -#define MX1ADS_ASP_OFFSET 0x15000 -#define MX1ADS_BTA_OFFSET 0x16000 -#define MX1ADS_I2C_OFFSET 0x17000 -#define MX1ADS_SSI_OFFSET 0x18000 -#define MX1ADS_SPI2_OFFSET 0x19000 -#define MX1ADS_MSHC_OFFSET 0x1A000 -#define MX1ADS_PLL_OFFSET 0x1B000 -#define MX1ADS_GPIO_OFFSET 0x1C000 -#define MX1ADS_EIM_OFFSET 0x20000 -#define MX1ADS_SDRAMC_OFFSET 0x21000 -#define MX1ADS_MMA_OFFSET 0x22000 -#define MX1ADS_AITC_OFFSET 0x23000 -#define MX1ADS_CSI_OFFSET 0x24000 - -/* - * Register BASEs, based on OFFSETs - * - */ - -#define MX1ADS_AIPI1_BASE (MX1ADS_AIPI1_OFFSET + MX1ADS_IO_BASE) -#define MX1ADS_WDT_BASE (MX1ADS_WDT_OFFSET + MX1ADS_IO_BASE) -#define MX1ADS_TIM1_BASE (MX1ADS_TIM1_OFFSET + MX1ADS_IO_BASE) -#define MX1ADS_TIM2_BASE (MX1ADS_TIM2_OFFSET + MX1ADS_IO_BASE) -#define MX1ADS_RTC_BASE (MX1ADS_RTC_OFFSET + MX1ADS_IO_BASE) -#define MX1ADS_LCDC_BASE (MX1ADS_LCDC_OFFSET + MX1ADS_IO_BASE) -#define MX1ADS_UART1_BASE (MX1ADS_UART1_OFFSET + MX1ADS_IO_BASE) -#define MX1ADS_UART2_BASE (MX1ADS_UART2_OFFSET + MX1ADS_IO_BASE) -#define MX1ADS_PWM_BASE (MX1ADS_PWM_OFFSET + MX1ADS_IO_BASE) -#define MX1ADS_DMAC_BASE (MX1ADS_DMAC_OFFSET + MX1ADS_IO_BASE) -#define MX1ADS_AIPI2_BASE (MX1ADS_AIPI2_OFFSET + MX1ADS_IO_BASE) -#define MX1ADS_SIM_BASE (MX1ADS_SIM_OFFSET + MX1ADS_IO_BASE) -#define MX1ADS_USBD_BASE (MX1ADS_USBD_OFFSET + MX1ADS_IO_BASE) -#define MX1ADS_SPI1_BASE (MX1ADS_SPI1_OFFSET + MX1ADS_IO_BASE) -#define MX1ADS_MMC_BASE (MX1ADS_MMC_OFFSET + MX1ADS_IO_BASE) -#define MX1ADS_ASP_BASE (MX1ADS_ASP_OFFSET + MX1ADS_IO_BASE) -#define MX1ADS_BTA_BASE (MX1ADS_BTA_OFFSET + MX1ADS_IO_BASE) -#define MX1ADS_I2C_BASE (MX1ADS_I2C_OFFSET + MX1ADS_IO_BASE) -#define MX1ADS_SSI_BASE (MX1ADS_SSI_OFFSET + MX1ADS_IO_BASE) -#define MX1ADS_SPI2_BASE (MX1ADS_SPI2_OFFSET + MX1ADS_IO_BASE) -#define MX1ADS_MSHC_BASE (MX1ADS_MSHC_OFFSET + MX1ADS_IO_BASE) -#define MX1ADS_PLL_BASE (MX1ADS_PLL_OFFSET + MX1ADS_IO_BASE) -#define MX1ADS_GPIO_BASE (MX1ADS_GPIO_OFFSET + MX1ADS_IO_BASE) -#define MX1ADS_EIM_BASE (MX1ADS_EIM_OFFSET + MX1ADS_IO_BASE) -#define MX1ADS_SDRAMC_BASE (MX1ADS_SDRAMC_OFFSET + MX1ADS_IO_BASE) -#define MX1ADS_MMA_BASE (MX1ADS_MMA_OFFSET + MX1ADS_IO_BASE) -#define MX1ADS_AITC_BASE (MX1ADS_AITC_OFFSET + MX1ADS_IO_BASE) -#define MX1ADS_CSI_BASE (MX1ADS_CSI_OFFSET + MX1ADS_IO_BASE) - -/* - * MX1 Interrupt numbers - * - */ -#define INT_SOFTINT 0 -#define CSI_INT 6 -#define DSPA_MAC_INT 7 -#define DSPA_INT 8 -#define COMP_INT 9 -#define MSHC_XINT 10 -#define GPIO_INT_PORTA 11 -#define GPIO_INT_PORTB 12 -#define GPIO_INT_PORTC 13 -#define LCDC_INT 14 -#define SIM_INT 15 -#define SIM_DATA_INT 16 -#define RTC_INT 17 -#define RTC_SAMINT 18 -#define UART2_MINT_PFERR 19 -#define UART2_MINT_RTS 20 -#define UART2_MINT_DTR 21 -#define UART2_MINT_UARTC 22 -#define UART2_MINT_TX 23 -#define UART2_MINT_RX 24 -#define UART1_MINT_PFERR 25 -#define UART1_MINT_RTS 26 -#define UART1_MINT_DTR 27 -#define UART1_MINT_UARTC 28 -#define UART1_MINT_TX 29 -#define UART1_MINT_RX 30 -#define VOICE_DAC_INT 31 -#define VOICE_ADC_INT 32 -#define PEN_DATA_INT 33 -#define PWM_INT 34 -#define SDHC_INT 35 -#define I2C_INT 39 -#define CSPI_INT 41 -#define SSI_TX_INT 42 -#define SSI_TX_ERR_INT 43 -#define SSI_RX_INT 44 -#define SSI_RX_ERR_INT 45 -#define TOUCH_INT 46 -#define USBD_INT0 47 -#define USBD_INT1 48 -#define USBD_INT2 49 -#define USBD_INT3 50 -#define USBD_INT4 51 -#define USBD_INT5 52 -#define USBD_INT6 53 -#define BTSYS_INT 55 -#define BTTIM_INT 56 -#define BTWUI_INT 57 -#define TIMER2_INT 58 -#define TIMER1_INT 59 -#define DMA_ERR 60 -#define DMA_INT 61 -#define GPIO_INT_PORTD 62 - -#define MAXIRQNUM 62 -#define MAXFIQNUM 62 -#define MAXSWINUM 62 - -#define TICKS_PER_uSEC 24 - -/* - * These are useconds NOT ticks. - * - */ -#define mSEC_1 1000 -#define mSEC_5 (mSEC_1 * 5) -#define mSEC_10 (mSEC_1 * 10) -#define mSEC_25 (mSEC_1 * 25) -#define SEC_1 (mSEC_1 * 1000) - -#endif diff --git a/include/mpc824x.h b/include/mpc824x.h index 0cd7898e13..30fc795382 100644 --- a/include/mpc824x.h +++ b/include/mpc824x.h @@ -297,6 +297,7 @@ #define PBESR 0x800000c7 /* PCI Bus Error Status Register */ #define PBEAR 0x800000c8 /* Processor/PCI Bus Error Status Register */ #define AMBOR 0x800000e0 /* Address Map B Options Register */ +#define PCMBCR 0x800000e1 /* PCI/Memory Buffer Configuration */ #define MCCR1 0x800000f0 /* Memory Control Configuration Register 1 */ #define MCCR2 0x800000f4 /* Memory Control Configuration Register 2 */ #define MCCR3 0x800000f8 /* Memory Control Configuration Register 3 */ diff --git a/include/serial.h b/include/serial.h new file mode 100644 index 0000000000..c206540cc6 --- /dev/null +++ b/include/serial.h @@ -0,0 +1,30 @@ +#ifndef __SERIAL_H__ +#define __SERIAL_H__ + +#define NAMESIZE 16 +#define CTLRSIZE 8 + +struct serial_device { + char name[NAMESIZE]; + char ctlr[CTLRSIZE]; + + int (*init) (void); + void (*setbrg) (void); + int (*getc) (void); + int (*tstc) (void); + void (*putc) (const char c); + void (*puts) (const char *s); + + struct serial_device *next; +}; + +extern struct serial_device serial_smc_device; +extern struct serial_device serial_scc_device; +extern struct serial_device * default_serial_console (void); + +extern void serial_initialize(void); +extern void serial_devices_init(void); +extern int serial_assign(char * name); +extern void serial_reinit_all(void); + +#endif diff --git a/lib_arm/board.c b/lib_arm/board.c index 9cffb4ec24..6f8c7fec6f 100644 --- a/lib_arm/board.c +++ b/lib_arm/board.c @@ -250,6 +250,9 @@ void start_armboot (void) #endif /* CONFIG_VFD */ #ifdef CONFIG_LCD +# ifndef PAGE_SIZE +# define PAGE_SIZE 4096 +# endif /* * reserve memory for LCD display (always full pages) */ diff --git a/lib_ppc/board.c b/lib_ppc/board.c index 42b467131f..97753b3139 100644 --- a/lib_ppc/board.c +++ b/lib_ppc/board.c @@ -48,6 +48,7 @@ #include #endif #include +#include #ifdef CFG_ALLOC_DPRAM #if !(defined(CONFIG_8260)||defined(CONFIG_MPC8560)) #include @@ -582,6 +583,10 @@ void board_init_r (gd_t *id, ulong dest_addr) monitor_flash_len = (ulong)&__init_end - dest_addr; +#ifdef CONFIG_SERIAL_MULTI + serial_initialize(); +#endif + /* * We have to relocate the command table manually */ @@ -872,7 +877,6 @@ void board_init_r (gd_t *id, ulong dest_addr) defined(CONFIG_IP860) || \ defined(CONFIG_IVML24) || \ defined(CONFIG_IVMS8) || \ - defined(CONFIG_LWMON) || \ defined(CONFIG_MPC8260ADS) || \ defined(CONFIG_MPC8266ADS) || \ defined(CONFIG_MPC8560ADS) || \ diff --git a/post/ether.c b/post/ether.c index 47aa3526b8..660620e8f6 100644 --- a/post/ether.c +++ b/post/ether.c @@ -49,6 +49,7 @@ #include #include +#include #define MIN_PACKET_LENGTH 64 #define MAX_PACKET_LENGTH 256 @@ -77,8 +78,6 @@ static struct { static char *ctlr_name[1] = { "SCC" }; -static int used_by_uart[1] = { -1 }; - /* Ethernet Transmit and Receive Buffers */ #define DBUF_LENGTH 1520 @@ -458,6 +457,7 @@ static void scc_halt (int scc_index) immr->im_cpm.cp_scc[scc_index].scc_gsmrl &= ~(SCC_GSMRL_ENR | SCC_GSMRL_ENT); + immr->im_ioport.iop_pcso &= ~(PC_ENET_CLSN | PC_ENET_RENA); } static int scc_send (int index, volatile void *packet, int length) @@ -513,7 +513,7 @@ static int scc_recv (int index, void *packet, int max_length) rxIdx++; } - Done: +Done: return length; } @@ -579,16 +579,10 @@ static int test_ctlr (int ctlr, int index) res = 0; - Done: +Done: ctlr_proc[ctlr].halt (index); -#if !defined(CONFIG_8xx_CONS_NONE) - if (used_by_uart[ctlr] == index) { - serial_init (); - } -#endif - /* * SCC2 Ethernet parameter RAM space overlaps * the SPI parameter RAM space. So we need to restore @@ -614,16 +608,6 @@ int ether_post_test (int flags) int res = 0; int i; -#if defined(CONFIG_8xx_CONS_SCC1) - used_by_uart[CTLR_SCC] = 0; -#elif defined(CONFIG_8xx_CONS_SCC2) - used_by_uart[CTLR_SCC] = 1; -#elif defined(CONFIG_8xx_CONS_SCC3) - used_by_uart[CTLR_SCC] = 2; -#elif defined(CONFIG_8xx_CONS_SCC4) - used_by_uart[CTLR_SCC] = 3; -#endif - ctlr_proc[CTLR_SCC].init = scc_init; ctlr_proc[CTLR_SCC].halt = scc_halt; ctlr_proc[CTLR_SCC].send = scc_send; @@ -635,6 +619,9 @@ int ether_post_test (int flags) } } +#if !defined(CONFIG_8xx_CONS_NONE) + serial_reinit_all (); +#endif return res; } diff --git a/post/uart.c b/post/uart.c index f6936ca7fc..23bf036ba4 100644 --- a/post/uart.c +++ b/post/uart.c @@ -48,7 +48,7 @@ #error "Apparently a bad configuration, please fix." #endif #include -#include +#include #define CTLR_SMC 0 #define CTLR_SCC 1 @@ -65,14 +65,13 @@ static int ctlr_list[][2] = { }; static struct { void (*init) (int index); + void (*halt) (int index); void (*putc) (int index, const char c); int (*getc) (int index); } ctlr_proc[2]; static char *ctlr_name[2] = { "SMC", "SCC" }; -static int used_by_uart[2] = { -1, -1 }; - static int proff_smc[] = { PROFF_SMC1, PROFF_SMC2 }; static int proff_scc[] = { PROFF_SCC1, PROFF_SCC2, PROFF_SCC3, PROFF_SCC4 }; @@ -212,6 +211,10 @@ static void smc_init (int smc_index) sp->smc_smcmr |= SMCMR_REN | SMCMR_TEN; } +static void smc_halt(int smc_index) +{ +} + static void smc_putc (int smc_index, const char c) { volatile cbd_t *tbdf; @@ -419,6 +422,15 @@ static void scc_init (int scc_index) sp->scc_gsmrl |= (SCC_GSMRL_ENR | SCC_GSMRL_ENT); } +static void scc_halt(int scc_index) +{ + volatile immap_t *im = (immap_t *) CFG_IMMR; + volatile cpm8xx_t *cp = &(im->im_cpm); + volatile scc_t *sp = (scc_t *) & (cp->cp_scc[scc_index]); + + sp->scc_gsmrl &= ~(SCC_GSMRL_ENR | SCC_GSMRL_ENT | SCC_GSMRL_DIAG_LE); +} + static void scc_putc (int scc_index, const char c) { volatile cbd_t *tbdf; @@ -496,12 +508,6 @@ static int test_ctlr (int ctlr, int index) char test_str[] = "*** UART Test String ***\r\n"; int i; -#if !defined(CONFIG_8xx_CONS_NONE) - if (used_by_uart[ctlr] == index) { - while (ctlr_proc[ctlr].getc (index) != -1); - } -#endif - ctlr_proc[ctlr].init (index); for (i = 0; i < sizeof (test_str) - 1; i++) { @@ -512,13 +518,8 @@ static int test_ctlr (int ctlr, int index) res = 0; - Done: - -#if !defined(CONFIG_8xx_CONS_NONE) - if (used_by_uart[ctlr] == index) { - serial_init (); - } -#endif +Done: + ctlr_proc[ctlr].halt (index); if (res != 0) { post_log ("uart %s%d test failed\n", @@ -533,25 +534,13 @@ int uart_post_test (int flags) int res = 0; int i; -#if defined(CONFIG_8xx_CONS_SMC1) - used_by_uart[CTLR_SMC] = 0; -#elif defined(CONFIG_8xx_CONS_SMC2) - used_by_uart[CTLR_SMC] = 1; -#elif defined(CONFIG_8xx_CONS_SCC1) - used_by_uart[CTLR_SCC] = 0; -#elif defined(CONFIG_8xx_CONS_SCC2) - used_by_uart[CTLR_SCC] = 1; -#elif defined(CONFIG_8xx_CONS_SCC3) - used_by_uart[CTLR_SCC] = 2; -#elif defined(CONFIG_8xx_CONS_SCC4) - used_by_uart[CTLR_SCC] = 3; -#endif - ctlr_proc[CTLR_SMC].init = smc_init; + ctlr_proc[CTLR_SMC].halt = smc_halt; ctlr_proc[CTLR_SMC].putc = smc_putc; ctlr_proc[CTLR_SMC].getc = smc_getc; ctlr_proc[CTLR_SCC].init = scc_init; + ctlr_proc[CTLR_SCC].halt = scc_halt; ctlr_proc[CTLR_SCC].putc = scc_putc; ctlr_proc[CTLR_SCC].getc = scc_getc; @@ -561,6 +550,10 @@ int uart_post_test (int flags) } } +#if !defined(CONFIG_8xx_CONS_NONE) + serial_reinit_all (); +#endif + return res; } -- 2.39.5