From 2c4ef30b11f459028c20185f41320e856db8c3a1 Mon Sep 17 00:00:00 2001 From: =?utf8?q?=C3=98yvind=20Harboe?= Date: Tue, 17 Aug 2010 21:51:36 +0200 Subject: [PATCH] mcb1700: Keil MCB1700 w/1768 config script MIME-Version: 1.0 Content-Type: text/plain; charset=utf8 Content-Transfer-Encoding: 8bit Ca. 93kBytes/s flashing speed @ 10MHz JTAG clock Signed-off-by: Øyvind Harboe --- tcl/board/mcb1700.cfg | 75 ++++++++++++++++++++++++++++++++++++++++++ tcl/target/lpc1768.cfg | 16 +++------ 2 files changed, 79 insertions(+), 12 deletions(-) create mode 100644 tcl/board/mcb1700.cfg diff --git a/tcl/board/mcb1700.cfg b/tcl/board/mcb1700.cfg new file mode 100644 index 00000000..845c7e20 --- /dev/null +++ b/tcl/board/mcb1700.cfg @@ -0,0 +1,75 @@ +# Keil MCB1700 PCB with 1768 +# +# Reset init script sets it to 100MHz +set CCLK 100000 + +source [find target/lpc1768.cfg] + +global MCB1700_CCLK +set MCB1700_CCLK $CCLK + +$_TARGETNAME configure -event reset-start { + # Start *real slow* as we do not know the + # state the boot rom left the clock in + jtag_khz 10 +} + +# Set up 100MHz clock to CPU +$_TARGETNAME configure -event reset-init { + # PLL0CON: Disable PLL + mww 0x400FC080 0x00000000 + # PLLFEED + mww 0x400FC08C 0x000000AA + # PLLFEED + mww 0x400FC08C 0x00000055 + + # CCLK=PLL/4 (=100 MHz) + mww 0x400FC104 0x00000003 + # CLKSRCSEL: Clock source = internal RC oscillator + mww 0x400FC10C 0x00000000 + + # PLL0CFG: M=50,N=1 -> PLL=400 MHz + mww 0x400FC084 0x00000031 + # PLLFEED + mww 0x400FC08C 0x000000AA + # PLLFEED + mww 0x400FC08C 0x00000055 + + # PLL0CON: Enable PLL + mww 0x400FC080 0x00000001 + # PLLFEED + mww 0x400FC08C 0x000000AA + # PLLFEED + mww 0x400FC08C 0x00000055 + + sleep 50 + + # PLL0CON: Connect PLL + mww 0x400FC080 0x00000003 + # PLLFEED + mww 0x400FC08C 0x000000AA + # PLLFEED + mww 0x400FC08C 0x00000055 + + # Dividing CPU clock by 8 should be pretty conservative + # + # + global MCB1700_CCLK + jtag_khz [expr $MCB1700_CCLK / 8] + + # Do not remap 0x0000-0x0020 to anything but the flash (i.e. select + # "User Flash Mode" where interrupt vectors are _not_ remapped, + # and reside in flash instead). + # + # See Table 612. Memory Mapping Control register (MEMMAP - 0x400F C040) bit description + # Bit Symbol Value Description Reset + # value + # 0 MAP Memory map control. 0 + # 0 Boot mode. A portion of the Boot ROM is mapped to address 0. + # 1 User mode. The on-chip Flash memory is mapped to address 0. + # 31:1 - Reserved. The value read from a reserved bit is not defined. NA + # + # http://ics.nxp.com/support/documents/microcontrollers/?scope=LPC1768&type=user + + mww 0x400FC040 0x01 +} diff --git a/tcl/target/lpc1768.cfg b/tcl/target/lpc1768.cfg index 07c5ab83..4a1ff0bc 100644 --- a/tcl/target/lpc1768.cfg +++ b/tcl/target/lpc1768.cfg @@ -47,18 +47,10 @@ set _FLASHNAME $_CHIPNAME.flash flash bank $_FLASHNAME lpc2000 0x0 0x80000 0 0 $_TARGETNAME \ lpc1700 $_CCLK calc_checksum -# Although rclk "appears to work", it turns out that this yields -# 4MHz whereas the "correct" rate is CCLK/6, which is not what -# you get with rclk. -# -# Also, crank down the frequency further as we're running of an -# RC oscillator instead of crystal. -# -# Setting up XTAL in the reset-init sequence could be worth -# the effort if you need to program the flash which is pretty -# big on these devices. -# -jtag_khz 100 +# Run with *real slow* clock by default since the +# boot rom could have been playing with the PLL, so +# we have no idea what clock the target is running at. +jtag_khz 10 $_TARGETNAME configure -event reset-init { # Do not remap 0x0000-0x0020 to anything but the flash (i.e. select -- 2.39.5