From 2eadf1e847f4880c698cae8dca857714e464e471 Mon Sep 17 00:00:00 2001 From: Matthias Welwarsky Date: Thu, 19 Apr 2018 09:56:14 +0200 Subject: [PATCH] board: add configuration for stm32f103c8 "Blue Pill" The "Blue Pill" is a popular development board with an STM32F103C8 micro controller. According to sources, it has a 128kB Flash on board even though the option bytes only report 64kB. This patch therefore also modifies target/stm32f1x.cfg to take an optional FLASH_SIZE variable into account which the board file sets to 0x20000. Change-Id: I8a78ccd2b5faf637c539ee3cf8136789ee15c95d Signed-off-by: Matthias Welwarsky Reviewed-on: http://openocd.zylin.com/4495 Tested-by: jenkins Reviewed-by: Tomas Vanek --- tcl/board/stm32f103c8_blue_pill.cfg | 14 ++++++++++++++ tcl/target/stm32f1x.cfg | 10 +++++++++- 2 files changed, 23 insertions(+), 1 deletion(-) create mode 100644 tcl/board/stm32f103c8_blue_pill.cfg diff --git a/tcl/board/stm32f103c8_blue_pill.cfg b/tcl/board/stm32f103c8_blue_pill.cfg new file mode 100644 index 00000000..2487f350 --- /dev/null +++ b/tcl/board/stm32f103c8_blue_pill.cfg @@ -0,0 +1,14 @@ +# STM32F103C8 "Blue Pill" + +# NOTE: +# There is a fair bit of confusion about whether the "Blue Pill" has 128kB or 64kB flash size. +# The most likely cause is that there exist a -C8 and a -CB variant of the STM32F103, where +# the C8 has 64kB, the CB has 128kB as per specification. "Blue Pill" boards are manufactured +# by a lot of different vendors, some may actually use the CB variant but from a cursory look +# it very hard to tell them apart ("C8" and "CB" look very similar). Nevertheless, people have +# tried using the full 128kB of flash on the C8 and found it to be working. Hence this board file +# overrides the internal size detection. Be aware though that you may be using you particular +# board outside of its specification. If in doubt, comment the following line. +set FLASH_SIZE 0x20000 + +source [find target/stm32f1x.cfg] diff --git a/tcl/target/stm32f1x.cfg b/tcl/target/stm32f1x.cfg index e0f6ede9..471878d7 100644 --- a/tcl/target/stm32f1x.cfg +++ b/tcl/target/stm32f1x.cfg @@ -22,6 +22,14 @@ if { [info exists WORKAREASIZE] } { set _WORKAREASIZE 0x1000 } +# Allow overriding the Flash bank size +if { [info exists FLASH_SIZE] } { + set _FLASH_SIZE $FLASH_SIZE +} else { + # autodetect size + set _FLASH_SIZE 0 +} + #jtag scan chain if { [info exists CPUTAPID] } { set _CPUTAPID $CPUTAPID @@ -49,7 +57,7 @@ $_TARGETNAME configure -work-area-phys 0x20000000 -work-area-size $_WORKAREASIZE # flash size will be probed set _FLASHNAME $_CHIPNAME.flash -flash bank $_FLASHNAME stm32f1x 0x08000000 0 0 0 $_TARGETNAME +flash bank $_FLASHNAME stm32f1x 0x08000000 $_FLASH_SIZE 0 0 $_TARGETNAME # JTAG speed should be <= F_CPU/6. F_CPU after reset is 8MHz, so use F_JTAG = 1MHz adapter_khz 1000 -- 2.39.5