From 48b6c32d7706e58f5113b539cf695ec0403c3b45 Mon Sep 17 00:00:00 2001 From: Simon Glass Date: Thu, 2 Jul 2015 18:16:18 -0600 Subject: [PATCH] dts: exynos: pit: Add a new node for the parade video bridge driver The new driver supports driver model and configuration via device tree. Add a node for pit, which needs this driver. Signed-off-by: Simon Glass --- arch/arm/dts/exynos5420-peach-pit.dts | 128 +++++++++++++++++++++++++- 1 file changed, 123 insertions(+), 5 deletions(-) diff --git a/arch/arm/dts/exynos5420-peach-pit.dts b/arch/arm/dts/exynos5420-peach-pit.dts index 5182b2b1c1..2d2b7c9bde 100644 --- a/arch/arm/dts/exynos5420-peach-pit.dts +++ b/arch/arm/dts/exynos5420-peach-pit.dts @@ -65,11 +65,129 @@ compatible = "maxim,max98090-codec"; }; - edp-lvds-bridge@48 { - compatible = "parade,ps8625"; - reg = <0x48>; - sleep-gpio = <&gpx3 5 GPIO_ACTIVE_HIGH>; - reset-gpio = <&gpy7 7 GPIO_ACTIVE_HIGH>; + edp-lvds-bridge@48 { + compatible = "parade,ps8625"; + reg = <0x48>; + sleep-gpios = <&gpx3 5 GPIO_ACTIVE_LOW>; + reset-gpios = <&gpy7 7 GPIO_ACTIVE_LOW>; + parade,regs = /bits/ 8 < + 0x02 0xa1 0x01 /* HPD low */ + /* + * SW setting + * [1:0] SW output 1.2V voltage is lower to 96% + */ + 0x04 0x14 0x01 + /* + * RCO SS setting + * [5:4] = b01 0.5%, b10 1%, b11 1.5% + */ + 0x04 0xe3 0x20 + 0x04 0xe2 0x80 /* [7] RCO SS enable */ + /* + * RPHY Setting + * [3:2] CDR tune wait cycle before + * measure for fine tune b00: 1us, + * 01: 0.5us, 10:2us, 11:4us. + */ + 0x04 0x8a 0x0c + 0x04 0x89 0x08 /* [3] RFD always on */ + /* + * CTN lock in/out: + * 20000ppm/80000ppm. Lock out 2 + * times. + */ + 0x04 0x71 0x2d + /* + * 2.7G CDR settings + * NOF=40LSB for HBR CDR setting + */ + 0x04 0x7d 0x07 + 0x04 0x7b 0x00 /* [1:0] Fmin=+4bands */ + 0x04 0x7a 0xfd /* [7:5] DCO_FTRNG=+-40% */ + /* + * 1.62G CDR settings + * [5:2]NOF=64LSB [1:0]DCO scale is 2/5 + */ + 0x04 0xc0 0x12 + 0x04 0xc1 0x92 /* Gitune=-37% */ + 0x04 0xc2 0x1c /* Fbstep=100% */ + 0x04 0x32 0x80 /* [7]LOS signal disable */ + /* + * RPIO Setting + * [7:4] LVDS driver bias current : + * 75% (250mV swing) + */ + 0x04 0x00 0xb0 + /* + * [7:6] Right-bar GPIO output strength is 8mA + */ + 0x04 0x15 0x40 + /* EQ Training State Machine Setting */ + 0x04 0x54 0x10 /* RCO calibration start */ + /* [4:0] MAX_LANE_COUNT set to one lane */ + 0x01 0x02 0x81 + /* [4:0] LANE_COUNT_SET set to one lane */ + 0x01 0x21 0x81 + 0x00 0x52 0x20 + 0x00 0xf1 0x03 /* HPD CP toggle enable */ + 0x00 0x62 0x41 + /* Counter number add 1ms counter delay */ + 0x00 0xf6 0x01 + /* + * [6]PWM function control by + * DPCD0040f[7], default is PWM + * block always works. + */ + 0x00 0x77 0x06 + /* + * 04h Adjust VTotal tolerance to + * fix the 30Hz no display issue + */ + 0x00 0x4c 0x04 + /* DPCD00400='h00, Parade OUI = 'h001cf8 */ + 0x01 0xc0 0x00 + 0x01 0xc1 0x1c /* DPCD00401='h1c */ + 0x01 0xc2 0xf8 /* DPCD00402='hf8 */ + /* + * DPCD403~408 = ASCII code + * D2SLV5='h4432534c5635 + */ + 0x01 0xc3 0x44 + 0x01 0xc4 0x32 /* DPCD404 */ + 0x01 0xc5 0x53 /* DPCD405 */ + 0x01 0xc6 0x4c /* DPCD406 */ + 0x01 0xc7 0x56 /* DPCD407 */ + 0x01 0xc8 0x35 /* DPCD408 */ + /* + * DPCD40A, Initial Code major revision + * '01' + */ + 0x01 0xca 0x01 + /* DPCD40B Initial Code minor revision '05' */ + 0x01 0xcb 0x05 + /* DPCD720 Select internal PWM */ + 0x01 0xa5 0xa0 + /* + * FFh for 100% PWM of brightness, 0h for 0% + * brightness + */ + 0x01 0xa7 0xff + /* + * Set LVDS output as 6bit-VESA mapping, + * single LVDS channel + */ + 0x01 0xcc 0x13 + /* Enable SSC set by register */ + 0x02 0xb1 0x20 + /* + * Set SSC enabled and +/-1% central + * spreading + */ + 0x04 0x10 0x16 + /* MPU Clock source: LC => RCO */ + 0x04 0x59 0x60 + 0x04 0x54 0x14 /* LC -> RCO */ + 0x02 0xa1 0x91>; /* HPD high */ }; }; -- 2.39.5