From 55a42b33f2e9b9f6330396fc6d89878a5deacc75 Mon Sep 17 00:00:00 2001 From: Peng Fan Date: Thu, 11 Aug 2016 14:02:57 +0800 Subject: [PATCH] arm: imx: add i.MX6ULL 14x14 EVK board support Add i.MX6ULL EVK board support: Add device tree file, which is copied from NXP Linux. Enabled DM_MMC, DM_GPIO, DM_I2C, DM_SPI, PINCTRL, DM_REGULATOR. The uart iomux settings are still keeped in board file. Boot Log: U-Boot 2016.09-rc1-00366-gbb419ef-dirty (Aug 11 2016 - 13:08:58 +0800) CPU: Freescale i.MX6ULL rev1.0 at 396MHz CPU: Commercial temperature grade (0C to 95C) at 15C Reset cause: POR Model: Freescale i.MX6 ULL 14x14 EVK Board Board: MX6ULL 14x14 EVK DRAM: 512 MiB MMC: initialized IMX pinctrl driver FSL_SDHC: 0, FSL_SDHC: 1 In: serial Out: serial Err: serial Net: CPU Net Initialization Failed No ethernet found. Hit any key to stop autoboot: 0 => mmc dev 1 switch to partitions #0, OK mmc1 is current device Signed-off-by: Peng Fan Cc: Stefano Babic --- arch/arm/cpu/armv7/mx6/Kconfig | 7 + arch/arm/dts/Makefile | 2 + arch/arm/dts/imx6ull-14x14-evk.dts | 527 +++++++++++++++++++++++++ board/freescale/mx6ullevk/Kconfig | 12 + board/freescale/mx6ullevk/MAINTAINERS | 6 + board/freescale/mx6ullevk/Makefile | 6 + board/freescale/mx6ullevk/imximage.cfg | 116 ++++++ board/freescale/mx6ullevk/mx6ullevk.c | 99 +++++ configs/mx6ull_14x14_evk_defconfig | 30 ++ include/configs/mx6ullevk.h | 180 +++++++++ 10 files changed, 985 insertions(+) create mode 100644 arch/arm/dts/imx6ull-14x14-evk.dts create mode 100644 board/freescale/mx6ullevk/Kconfig create mode 100644 board/freescale/mx6ullevk/MAINTAINERS create mode 100644 board/freescale/mx6ullevk/Makefile create mode 100644 board/freescale/mx6ullevk/imximage.cfg create mode 100644 board/freescale/mx6ullevk/mx6ullevk.c create mode 100644 configs/mx6ull_14x14_evk_defconfig create mode 100644 include/configs/mx6ullevk.h diff --git a/arch/arm/cpu/armv7/mx6/Kconfig b/arch/arm/cpu/armv7/mx6/Kconfig index 32405c6fe4..d851b264ea 100644 --- a/arch/arm/cpu/armv7/mx6/Kconfig +++ b/arch/arm/cpu/armv7/mx6/Kconfig @@ -137,6 +137,12 @@ config TARGET_MX6UL_14X14_EVK select DM_THERMAL select SUPPORT_SPL +config TARGET_MX6ULL_14X14_EVK + bool "Support mx6ull_14x14_evk" + select MX6ULL + select DM + select DM_THERMAL + config TARGET_NITROGEN6X bool "nitrogen6x" @@ -226,6 +232,7 @@ source "board/freescale/mx6slevk/Kconfig" source "board/freescale/mx6sxsabresd/Kconfig" source "board/freescale/mx6sxsabreauto/Kconfig" source "board/freescale/mx6ul_14x14_evk/Kconfig" +source "board/freescale/mx6ullevk/Kconfig" source "board/phytec/pcm058/Kconfig" source "board/gateworks/gw_ventana/Kconfig" source "board/kosagi/novena/Kconfig" diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile index 032c5aebc1..19140b48ca 100644 --- a/arch/arm/dts/Makefile +++ b/arch/arm/dts/Makefile @@ -280,6 +280,8 @@ dtb-$(CONFIG_VF610) += vf500-colibri.dtb \ vf610-twr.dtb \ pcm052.dtb +dtb-$(CONFIG_MX6) += imx6ull-14x14-evk.dtb + dtb-$(CONFIG_SOC_KEYSTONE) += k2hk-evm.dtb \ k2l-evm.dtb \ k2e-evm.dtb \ diff --git a/arch/arm/dts/imx6ull-14x14-evk.dts b/arch/arm/dts/imx6ull-14x14-evk.dts new file mode 100644 index 0000000000..375bd4ea31 --- /dev/null +++ b/arch/arm/dts/imx6ull-14x14-evk.dts @@ -0,0 +1,527 @@ +/* + * Copyright (C) 2016 Freescale Semiconductor, Inc. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +/dts-v1/; + +#include +#include "imx6ull.dtsi" + +/ { + model = "Freescale i.MX6 ULL 14x14 EVK Board"; + compatible = "fsl,imx6ull-14x14-evk", "fsl,imx6ull"; + + chosen { + stdout-path = &uart1; + }; + + memory { + reg = <0x80000000 0x20000000>; + }; + + backlight { + compatible = "pwm-backlight"; + pwms = <&pwm1 0 5000000>; + brightness-levels = <0 4 8 16 32 64 128 255>; + default-brightness-level = <6>; + status = "okay"; + }; + + regulators { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <0>; + + reg_can_3v3: regulator@0 { + compatible = "regulator-fixed"; + reg = <0>; + regulator-name = "can-3v3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpios = <&gpio_spi 3 GPIO_ACTIVE_LOW>; + }; + + reg_sd1_vmmc: regulator@1 { + compatible = "regulator-fixed"; + regulator-name = "VSD_3V3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpio1 9 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + reg_gpio_dvfs: regulator-gpio { + compatible = "regulator-gpio"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_dvfs>; + regulator-min-microvolt = <1300000>; + regulator-max-microvolt = <1400000>; + regulator-name = "gpio_dvfs"; + regulator-type = "voltage"; + gpios = <&gpio5 3 GPIO_ACTIVE_HIGH>; + states = <1300000 0x1 1400000 0x0>; + }; + }; + + spi4 { + compatible = "spi-gpio"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_spi4>; + status = "okay"; + gpio-sck = <&gpio5 11 0>; + gpio-mosi = <&gpio5 10 0>; + cs-gpios = <&gpio5 7 0>; + num-chipselects = <1>; + #address-cells = <1>; + #size-cells = <0>; + + gpio_spi: gpio_spi@0 { + compatible = "fairchild,74hc595"; + gpio-controller; + oe-gpios = <&gpio5 8 0>; + #gpio-cells = <2>; + reg = <0>; + registers-number = <1>; + registers-default = /bits/ 8 <0x57>; + spi-max-frequency = <100000>; + }; + }; +}; + +&cpu0 { + arm-supply = <®_arm>; + soc-supply = <®_soc>; + dc-supply = <®_gpio_dvfs>; +}; + +&clks { + assigned-clocks = <&clks IMX6UL_CLK_PLL4_AUDIO_DIV>; + assigned-clock-rates = <786432000>; +}; + +&fec1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_enet1>; + phy-mode = "rmii"; + phy-handle = <ðphy0>; + status = "okay"; +}; + +&fec2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_enet2>; + phy-mode = "rmii"; + phy-handle = <ðphy1>; + status = "okay"; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + ethphy0: ethernet-phy@2 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <2>; + }; + + ethphy1: ethernet-phy@1 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <1>; + }; + }; +}; + +&gpc { + fsl,cpu_pupscr_sw2iso = <0x1>; + fsl,cpu_pupscr_sw = <0x0>; + fsl,cpu_pdnscr_iso2sw = <0x1>; + fsl,cpu_pdnscr_iso = <0x1>; + fsl,ldo-bypass = <0>; /* DCDC, ldo-enable */ +}; + +&i2c1 { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c1>; + status = "okay"; + + mag3110@0e { + compatible = "fsl,mag3110"; + reg = <0x0e>; + position = <2>; + }; + + fxls8471@1e { + compatible = "fsl,fxls8471"; + reg = <0x1e>; + position = <0>; + interrupt-parent = <&gpio5>; + interrupts = <0 8>; + }; +}; + +&i2c2 { + clock_frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c2>; + status = "okay"; +}; + +&iomuxc { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_hog_1>; + imx6ul-evk { + pinctrl_hog_1: hoggrp-1 { + fsl,pins = < + MX6UL_PAD_UART1_RTS_B__GPIO1_IO19 0x17059 /* SD1 CD */ + MX6UL_PAD_GPIO1_IO05__USDHC1_VSELECT 0x17059 /* SD1 VSELECT */ + MX6UL_PAD_GPIO1_IO09__GPIO1_IO09 0x17059 /* SD1 RESET */ + >; + }; + + pinctrl_csi1: csi1grp { + fsl,pins = < + MX6UL_PAD_CSI_MCLK__CSI_MCLK 0x1b088 + MX6UL_PAD_CSI_PIXCLK__CSI_PIXCLK 0x1b088 + MX6UL_PAD_CSI_VSYNC__CSI_VSYNC 0x1b088 + MX6UL_PAD_CSI_HSYNC__CSI_HSYNC 0x1b088 + MX6UL_PAD_CSI_DATA00__CSI_DATA02 0x1b088 + MX6UL_PAD_CSI_DATA01__CSI_DATA03 0x1b088 + MX6UL_PAD_CSI_DATA02__CSI_DATA04 0x1b088 + MX6UL_PAD_CSI_DATA03__CSI_DATA05 0x1b088 + MX6UL_PAD_CSI_DATA04__CSI_DATA06 0x1b088 + MX6UL_PAD_CSI_DATA05__CSI_DATA07 0x1b088 + MX6UL_PAD_CSI_DATA06__CSI_DATA08 0x1b088 + MX6UL_PAD_CSI_DATA07__CSI_DATA09 0x1b088 + >; + }; + + pinctrl_enet1: enet1grp { + fsl,pins = < + MX6UL_PAD_ENET1_RX_EN__ENET1_RX_EN 0x1b0b0 + MX6UL_PAD_ENET1_RX_ER__ENET1_RX_ER 0x1b0b0 + MX6UL_PAD_ENET1_RX_DATA0__ENET1_RDATA00 0x1b0b0 + MX6UL_PAD_ENET1_RX_DATA1__ENET1_RDATA01 0x1b0b0 + MX6UL_PAD_ENET1_TX_EN__ENET1_TX_EN 0x1b0b0 + MX6UL_PAD_ENET1_TX_DATA0__ENET1_TDATA00 0x1b0b0 + MX6UL_PAD_ENET1_TX_DATA1__ENET1_TDATA01 0x1b0b0 + MX6UL_PAD_ENET1_TX_CLK__ENET1_REF_CLK1 0x4001b031 + >; + }; + + pinctrl_enet2: enet2grp { + fsl,pins = < + MX6UL_PAD_GPIO1_IO07__ENET2_MDC 0x1b0b0 + MX6UL_PAD_GPIO1_IO06__ENET2_MDIO 0x1b0b0 + MX6UL_PAD_ENET2_RX_EN__ENET2_RX_EN 0x1b0b0 + MX6UL_PAD_ENET2_RX_ER__ENET2_RX_ER 0x1b0b0 + MX6UL_PAD_ENET2_RX_DATA0__ENET2_RDATA00 0x1b0b0 + MX6UL_PAD_ENET2_RX_DATA1__ENET2_RDATA01 0x1b0b0 + MX6UL_PAD_ENET2_TX_EN__ENET2_TX_EN 0x1b0b0 + MX6UL_PAD_ENET2_TX_DATA0__ENET2_TDATA00 0x1b0b0 + MX6UL_PAD_ENET2_TX_DATA1__ENET2_TDATA01 0x1b0b0 + MX6UL_PAD_ENET2_TX_CLK__ENET2_REF_CLK2 0x4001b031 + >; + }; + + pinctrl_flexcan1: flexcan1grp{ + fsl,pins = < + MX6UL_PAD_UART3_RTS_B__FLEXCAN1_RX 0x1b020 + MX6UL_PAD_UART3_CTS_B__FLEXCAN1_TX 0x1b020 + >; + }; + + pinctrl_flexcan2: flexcan2grp{ + fsl,pins = < + MX6UL_PAD_UART2_RTS_B__FLEXCAN2_RX 0x1b020 + MX6UL_PAD_UART2_CTS_B__FLEXCAN2_TX 0x1b020 + >; + }; + + pinctrl_i2c1: i2c1grp { + fsl,pins = < + MX6UL_PAD_UART4_TX_DATA__I2C1_SCL 0x4001b8b0 + MX6UL_PAD_UART4_RX_DATA__I2C1_SDA 0x4001b8b0 + >; + }; + + pinctrl_i2c2: i2c2grp { + fsl,pins = < + MX6UL_PAD_UART5_TX_DATA__I2C2_SCL 0x4001b8b0 + MX6UL_PAD_UART5_RX_DATA__I2C2_SDA 0x4001b8b0 + >; + }; + + pinctrl_lcdif_dat: lcdifdatgrp { + fsl,pins = < + MX6UL_PAD_LCD_DATA00__LCDIF_DATA00 0x79 + MX6UL_PAD_LCD_DATA01__LCDIF_DATA01 0x79 + MX6UL_PAD_LCD_DATA02__LCDIF_DATA02 0x79 + MX6UL_PAD_LCD_DATA03__LCDIF_DATA03 0x79 + MX6UL_PAD_LCD_DATA04__LCDIF_DATA04 0x79 + MX6UL_PAD_LCD_DATA05__LCDIF_DATA05 0x79 + MX6UL_PAD_LCD_DATA06__LCDIF_DATA06 0x79 + MX6UL_PAD_LCD_DATA07__LCDIF_DATA07 0x79 + MX6UL_PAD_LCD_DATA08__LCDIF_DATA08 0x79 + MX6UL_PAD_LCD_DATA09__LCDIF_DATA09 0x79 + MX6UL_PAD_LCD_DATA10__LCDIF_DATA10 0x79 + MX6UL_PAD_LCD_DATA11__LCDIF_DATA11 0x79 + MX6UL_PAD_LCD_DATA12__LCDIF_DATA12 0x79 + MX6UL_PAD_LCD_DATA13__LCDIF_DATA13 0x79 + MX6UL_PAD_LCD_DATA14__LCDIF_DATA14 0x79 + MX6UL_PAD_LCD_DATA15__LCDIF_DATA15 0x79 + MX6UL_PAD_LCD_DATA16__LCDIF_DATA16 0x79 + MX6UL_PAD_LCD_DATA17__LCDIF_DATA17 0x79 + MX6UL_PAD_LCD_DATA18__LCDIF_DATA18 0x79 + MX6UL_PAD_LCD_DATA19__LCDIF_DATA19 0x79 + MX6UL_PAD_LCD_DATA20__LCDIF_DATA20 0x79 + MX6UL_PAD_LCD_DATA21__LCDIF_DATA21 0x79 + MX6UL_PAD_LCD_DATA22__LCDIF_DATA22 0x79 + MX6UL_PAD_LCD_DATA23__LCDIF_DATA23 0x79 + >; + }; + + pinctrl_lcdif_ctrl: lcdifctrlgrp { + fsl,pins = < + MX6UL_PAD_LCD_CLK__LCDIF_CLK 0x79 + MX6UL_PAD_LCD_ENABLE__LCDIF_ENABLE 0x79 + MX6UL_PAD_LCD_HSYNC__LCDIF_HSYNC 0x79 + MX6UL_PAD_LCD_VSYNC__LCDIF_VSYNC 0x79 + >; + }; + + pinctrl_pwm1: pwm1grp { + fsl,pins = < + MX6UL_PAD_GPIO1_IO08__PWM1_OUT 0x110b0 + >; + }; + + pinctrl_qspi: qspigrp { + fsl,pins = < + MX6UL_PAD_NAND_WP_B__QSPI_A_SCLK 0x70a1 + MX6UL_PAD_NAND_READY_B__QSPI_A_DATA00 0x70a1 + MX6UL_PAD_NAND_CE0_B__QSPI_A_DATA01 0x70a1 + MX6UL_PAD_NAND_CE1_B__QSPI_A_DATA02 0x70a1 + MX6UL_PAD_NAND_CLE__QSPI_A_DATA03 0x70a1 + MX6UL_PAD_NAND_DQS__QSPI_A_SS0_B 0x70a1 + >; + }; + + pinctrl_uart1: uart1grp { + fsl,pins = < + MX6UL_PAD_UART1_TX_DATA__UART1_DCE_TX 0x1b0b1 + MX6UL_PAD_UART1_RX_DATA__UART1_DCE_RX 0x1b0b1 + >; + }; + + pinctrl_uart2: uart2grp { + fsl,pins = < + MX6UL_PAD_UART2_TX_DATA__UART2_DCE_TX 0x1b0b1 + MX6UL_PAD_UART2_RX_DATA__UART2_DCE_RX 0x1b0b1 + MX6UL_PAD_UART3_RX_DATA__UART2_DCE_RTS 0x1b0b1 + MX6UL_PAD_UART3_TX_DATA__UART2_DCE_CTS 0x1b0b1 + >; + }; + + pinctrl_uart2dte: uart2dtegrp { + fsl,pins = < + MX6UL_PAD_UART2_TX_DATA__UART2_DTE_RX 0x1b0b1 + MX6UL_PAD_UART2_RX_DATA__UART2_DTE_TX 0x1b0b1 + MX6UL_PAD_UART3_RX_DATA__UART2_DTE_CTS 0x1b0b1 + MX6UL_PAD_UART3_TX_DATA__UART2_DTE_RTS 0x1b0b1 + >; + }; + + pinctrl_usdhc1: usdhc1grp { + fsl,pins = < + MX6UL_PAD_SD1_CMD__USDHC1_CMD 0x17059 + MX6UL_PAD_SD1_CLK__USDHC1_CLK 0x10071 + MX6UL_PAD_SD1_DATA0__USDHC1_DATA0 0x17059 + MX6UL_PAD_SD1_DATA1__USDHC1_DATA1 0x17059 + MX6UL_PAD_SD1_DATA2__USDHC1_DATA2 0x17059 + MX6UL_PAD_SD1_DATA3__USDHC1_DATA3 0x17059 + >; + }; + + pinctrl_usdhc2: usdhc2grp { + fsl,pins = < + MX6UL_PAD_NAND_RE_B__USDHC2_CLK 0x10069 + MX6UL_PAD_NAND_WE_B__USDHC2_CMD 0x17059 + MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x17059 + MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x17059 + MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x17059 + MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x17059 + >; + }; + + pinctrl_wdog: wdoggrp { + fsl,pins = < + MX6UL_PAD_LCD_RESET__WDOG1_WDOG_ANY 0x30b0 + >; + }; + }; +}; + +&iomuxc_snvs { + pinctrl-names = "default_snvs"; + pinctrl-0 = <&pinctrl_hog_2>; + imx6ul-evk { + pinctrl_hog_2: hoggrp-2 { + fsl,pins = < + MX6ULL_PAD_SNVS_TAMPER0__GPIO5_IO00 0x80000000 + >; + }; + + pinctrl_dvfs: dvfsgrp { + fsl,pins = < + MX6ULL_PAD_SNVS_TAMPER3__GPIO5_IO03 0x79 + >; + }; + + pinctrl_lcdif_reset: lcdifresetgrp { + fsl,pins = < + /* used for lcd reset */ + MX6ULL_PAD_SNVS_TAMPER9__GPIO5_IO09 0x79 + >; + }; + + pinctrl_spi4: spi4grp { + fsl,pins = < + MX6ULL_PAD_BOOT_MODE0__GPIO5_IO10 0x70a1 + MX6ULL_PAD_BOOT_MODE1__GPIO5_IO11 0x70a1 + MX6ULL_PAD_SNVS_TAMPER7__GPIO5_IO07 0x70a1 + MX6ULL_PAD_SNVS_TAMPER8__GPIO5_IO08 0x80000000 + >; + }; + + pinctrl_sai2_hp_det_b: sai2_hp_det_grp { + fsl,pins = < + MX6ULL_PAD_SNVS_TAMPER4__GPIO5_IO04 0x17059 + >; + }; + }; +}; + + +&lcdif { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_lcdif_dat + &pinctrl_lcdif_ctrl + &pinctrl_lcdif_reset>; + display = <&display0>; + status = "okay"; + + display0: display { + bits-per-pixel = <16>; + bus-width = <24>; + + display-timings { + native-mode = <&timing0>; + timing0: timing0 { + clock-frequency = <9200000>; + hactive = <480>; + vactive = <272>; + hfront-porch = <8>; + hback-porch = <4>; + hsync-len = <41>; + vback-porch = <2>; + vfront-porch = <4>; + vsync-len = <10>; + + hsync-active = <0>; + vsync-active = <0>; + de-active = <1>; + pixelclk-active = <0>; + }; + }; + }; +}; + +&pwm1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pwm1>; + status = "okay"; +}; + +&qspi { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_qspi>; + status = "okay"; + ddrsmp=<0>; + + flash0: n25q256a@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "micron,n25q256a"; + spi-max-frequency = <29000000>; + spi-nor,ddr-quad-read-dummy = <6>; + reg = <0>; + }; +}; + +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart1>; + status = "okay"; +}; + +&uart2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart2>; + fsl,uart-has-rtscts; + /* for DTE mode, add below change */ + /* fsl,dte-mode; */ + /* pinctrl-0 = <&pinctrl_uart2dte>; */ + status = "okay"; +}; + +&usbotg1 { + dr_mode = "otg"; + srp-disable; + hnp-disable; + adp-disable; + status = "okay"; +}; + +&usbotg2 { + dr_mode = "host"; + disable-over-current; + status = "okay"; +}; + +&usbphy1 { + tx-d-cal = <0x5>; +}; + +&usbphy2 { + tx-d-cal = <0x5>; +}; + +&usdhc1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usdhc1>; + cd-gpios = <&gpio1 19 GPIO_ACTIVE_LOW>; + keep-power-in-suspend; + enable-sdio-wakeup; + vmmc-supply = <®_sd1_vmmc>; + status = "okay"; +}; + +&usdhc2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usdhc2>; + no-1-8-v; + non-removable; + keep-power-in-suspend; + enable-sdio-wakeup; + status = "okay"; +}; + +&wdog1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_wdog>; + fsl,wdog_b; +}; diff --git a/board/freescale/mx6ullevk/Kconfig b/board/freescale/mx6ullevk/Kconfig new file mode 100644 index 0000000000..7eec497e3e --- /dev/null +++ b/board/freescale/mx6ullevk/Kconfig @@ -0,0 +1,12 @@ +if TARGET_MX6ULL_14X14_EVK + +config SYS_BOARD + default "mx6ullevk" + +config SYS_VENDOR + default "freescale" + +config SYS_CONFIG_NAME + default "mx6ullevk" + +endif diff --git a/board/freescale/mx6ullevk/MAINTAINERS b/board/freescale/mx6ullevk/MAINTAINERS new file mode 100644 index 0000000000..4137674d36 --- /dev/null +++ b/board/freescale/mx6ullevk/MAINTAINERS @@ -0,0 +1,6 @@ +MX6ULLEVK BOARD +M: Peng Fan +S: Maintained +F: board/freescale/mx6ullevk/ +F: include/configs/mx6ullevk.h +F: configs/mx6ull_14x14_evk_defconfig diff --git a/board/freescale/mx6ullevk/Makefile b/board/freescale/mx6ullevk/Makefile new file mode 100644 index 0000000000..c64fba407e --- /dev/null +++ b/board/freescale/mx6ullevk/Makefile @@ -0,0 +1,6 @@ +# (C) Copyright 2016 Freescale Semiconductor, Inc. +# +# SPDX-License-Identifier: GPL-2.0+ +# + +obj-y := mx6ullevk.o diff --git a/board/freescale/mx6ullevk/imximage.cfg b/board/freescale/mx6ullevk/imximage.cfg new file mode 100644 index 0000000000..4604b62485 --- /dev/null +++ b/board/freescale/mx6ullevk/imximage.cfg @@ -0,0 +1,116 @@ +/* + * Copyright (C) 2016 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + * + * Refer docs/README.imxmage for more details about how-to configure + * and create imximage boot image + * + * The syntax is taken as close as possible with the kwbimage + */ + +#define __ASSEMBLY__ +#include + +/* image version */ + +IMAGE_VERSION 2 + +/* + * Boot Device : one of + * spi/sd/nand/onenand, qspi/nor + */ + +#ifdef CONFIG_SYS_BOOT_QSPI +BOOT_FROM qspi +#elif defined(CONFIG_SYS_BOOT_EIMNOR) +BOOT_FROM nor +#else +BOOT_FROM sd +#endif + +#ifdef CONFIG_USE_PLUGIN +/*PLUGIN plugin-binary-file IRAM_FREE_START_ADDR*/ +PLUGIN board/freescale/mx6ullevk/plugin.bin 0x00907000 +#else + +#ifdef CONFIG_SECURE_BOOT +CSF CONFIG_CSF_SIZE +#endif + +/* + * Device Configuration Data (DCD) + * + * Each entry must have the format: + * Addr-type Address Value + * + * where: + * Addr-type register length (1,2 or 4 bytes) + * Address absolute address of the register + * value value to be stored in the register + */ + +/* Enable all clocks */ +DATA 4 0x020c4068 0xffffffff +DATA 4 0x020c406c 0xffffffff +DATA 4 0x020c4070 0xffffffff +DATA 4 0x020c4074 0xffffffff +DATA 4 0x020c4078 0xffffffff +DATA 4 0x020c407c 0xffffffff +DATA 4 0x020c4080 0xffffffff + +DATA 4 0x020E04B4 0x000C0000 +DATA 4 0x020E04AC 0x00000000 +DATA 4 0x020E027C 0x00000030 +DATA 4 0x020E0250 0x00000030 +DATA 4 0x020E024C 0x00000030 +DATA 4 0x020E0490 0x00000030 +DATA 4 0x020E0288 0x000C0030 +DATA 4 0x020E0270 0x00000000 +DATA 4 0x020E0260 0x00000030 +DATA 4 0x020E0264 0x00000030 +DATA 4 0x020E04A0 0x00000030 +DATA 4 0x020E0494 0x00020000 +DATA 4 0x020E0280 0x00000030 +DATA 4 0x020E0284 0x00000030 +DATA 4 0x020E04B0 0x00020000 +DATA 4 0x020E0498 0x00000030 +DATA 4 0x020E04A4 0x00000030 +DATA 4 0x020E0244 0x00000030 +DATA 4 0x020E0248 0x00000030 +DATA 4 0x021B001C 0x00008000 +DATA 4 0x021B0800 0xA1390003 +DATA 4 0x021B080C 0x00000004 +DATA 4 0x021B083C 0x41640158 +DATA 4 0x021B0848 0x40403237 +DATA 4 0x021B0850 0x40403C33 +DATA 4 0x021B081C 0x33333333 +DATA 4 0x021B0820 0x33333333 +DATA 4 0x021B082C 0xf3333333 +DATA 4 0x021B0830 0xf3333333 +DATA 4 0x021B08C0 0x00944009 +DATA 4 0x021B08b8 0x00000800 +DATA 4 0x021B0004 0x0002002D +DATA 4 0x021B0008 0x1B333030 +DATA 4 0x021B000C 0x676B52F3 +DATA 4 0x021B0010 0xB66D0B63 +DATA 4 0x021B0014 0x01FF00DB +DATA 4 0x021B0018 0x00201740 +DATA 4 0x021B001C 0x00008000 +DATA 4 0x021B002C 0x000026D2 +DATA 4 0x021B0030 0x006B1023 +DATA 4 0x021B0040 0x0000004F +DATA 4 0x021B0000 0x84180000 +DATA 4 0x021B0890 0x00400000 +DATA 4 0x021B001C 0x02008032 +DATA 4 0x021B001C 0x00008033 +DATA 4 0x021B001C 0x00048031 +DATA 4 0x021B001C 0x15208030 +DATA 4 0x021B001C 0x04008040 +DATA 4 0x021B0020 0x00000800 +DATA 4 0x021B0818 0x00000227 +DATA 4 0x021B0004 0x0002552D +DATA 4 0x021B0404 0x00011006 +DATA 4 0x021B001C 0x00000000 + +#endif diff --git a/board/freescale/mx6ullevk/mx6ullevk.c b/board/freescale/mx6ullevk/mx6ullevk.c new file mode 100644 index 0000000000..489bf2114b --- /dev/null +++ b/board/freescale/mx6ullevk/mx6ullevk.c @@ -0,0 +1,99 @@ +/* + * Copyright (C) 2016 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +DECLARE_GLOBAL_DATA_PTR; + +#define UART_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \ + PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \ + PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST | PAD_CTL_HYS) + +int dram_init(void) +{ + gd->ram_size = imx_ddr_size(); + + return 0; +} + +static iomux_v3_cfg_t const uart1_pads[] = { + MX6_PAD_UART1_TX_DATA__UART1_DCE_TX | MUX_PAD_CTRL(UART_PAD_CTRL), + MX6_PAD_UART1_RX_DATA__UART1_DCE_RX | MUX_PAD_CTRL(UART_PAD_CTRL), +}; + +static void setup_iomux_uart(void) +{ + imx_iomux_v3_setup_multiple_pads(uart1_pads, ARRAY_SIZE(uart1_pads)); +} + +int board_mmc_get_env_dev(int devno) +{ + return devno; +} + +int mmc_map_to_kernel_blk(int devno) +{ + return devno; +} + +int board_early_init_f(void) +{ + setup_iomux_uart(); + + return 0; +} + +int board_init(void) +{ + /* Address of boot parameters */ + gd->bd->bi_boot_params = PHYS_SDRAM + 0x100; + + return 0; +} + +#ifdef CONFIG_CMD_BMODE +static const struct boot_mode board_boot_modes[] = { + /* 4 bit bus width */ + {"sd1", MAKE_CFGVAL(0x42, 0x20, 0x00, 0x00)}, + {"sd2", MAKE_CFGVAL(0x40, 0x28, 0x00, 0x00)}, + {"qspi1", MAKE_CFGVAL(0x10, 0x00, 0x00, 0x00)}, + {NULL, 0}, +}; +#endif + +int board_late_init(void) +{ +#ifdef CONFIG_CMD_BMODE + add_board_boot_modes(board_boot_modes); +#endif + +#ifdef CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG + setenv("board_name", "EVK"); + setenv("board_rev", "14X14"); +#endif + + return 0; +} + +int checkboard(void) +{ + puts("Board: MX6ULL 14x14 EVK\n"); + + return 0; +} diff --git a/configs/mx6ull_14x14_evk_defconfig b/configs/mx6ull_14x14_evk_defconfig new file mode 100644 index 0000000000..a106b5d9a1 --- /dev/null +++ b/configs/mx6ull_14x14_evk_defconfig @@ -0,0 +1,30 @@ +CONFIG_ARM=y +CONFIG_ARCH_MX6=y +CONFIG_TARGET_MX6ULL_14X14_EVK=y +CONFIG_DM_GPIO=y +CONFIG_DEFAULT_DEVICE_TREE="imx6ull-14x14-evk" +CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/freescale/mx6ullevk/imximage.cfg" +CONFIG_BOOTDELAY=3 +CONFIG_HUSH_PARSER=y +CONFIG_CMD_BOOTZ=y +# CONFIG_CMD_IMLS is not set +CONFIG_CMD_MEMTEST=y +CONFIG_CMD_MMC=y +CONFIG_CMD_I2C=y +CONFIG_CMD_GPIO=y +CONFIG_CMD_DHCP=y +CONFIG_CMD_PING=y +CONFIG_CMD_CACHE=y +CONFIG_CMD_EXT2=y +CONFIG_CMD_EXT4=y +CONFIG_CMD_EXT4_WRITE=y +CONFIG_CMD_FAT=y +CONFIG_CMD_FS_GENERIC=y +CONFIG_OF_CONTROL=y +CONFIG_DM_74X164=y +CONFIG_DM_I2C=y +CONFIG_DM_MMC=y +CONFIG_PINCTRL=y +CONFIG_PINCTRL_IMX6=y +CONFIG_DM_REGULATOR=y +CONFIG_DM_SPI=y diff --git a/include/configs/mx6ullevk.h b/include/configs/mx6ullevk.h new file mode 100644 index 0000000000..ccce9546b7 --- /dev/null +++ b/include/configs/mx6ullevk.h @@ -0,0 +1,180 @@ +/* + * Copyright (C) 2016 Freescale Semiconductor, Inc. + * + * Configuration settings for the Freescale i.MX6UL 14x14 EVK board. + * + * SPDX-License-Identifier: GPL-2.0+ + */ +#ifndef __MX6ULLEVK_CONFIG_H +#define __MX6ULLEVK_CONFIG_H + + +#include +#include +#include "mx6_common.h" +#include + +#ifdef CONFIG_SECURE_BOOT +#ifndef CONFIG_CSF_SIZE +#define CONFIG_CSF_SIZE 0x4000 +#endif +#endif + +#define PHYS_SDRAM_SIZE SZ_512M + +#define CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG + +#define CONFIG_DISPLAY_CPUINFO +#define CONFIG_DISPLAY_BOARDINFO + +/* Size of malloc() pool */ +#define CONFIG_SYS_MALLOC_LEN (16 * SZ_1M) + +#define CONFIG_BOARD_EARLY_INIT_F +#define CONFIG_BOARD_LATE_INIT + +#define CONFIG_MXC_GPIO + +#define CONFIG_MXC_UART +#define CONFIG_MXC_UART_BASE UART1_BASE + +/* MMC Configs */ +#ifdef CONFIG_FSL_USDHC +#define CONFIG_SYS_FSL_ESDHC_ADDR USDHC2_BASE_ADDR + +/* NAND pin conflicts with usdhc2 */ +#ifdef CONFIG_SYS_USE_NAND +#define CONFIG_SYS_FSL_USDHC_NUM 1 +#else +#define CONFIG_SYS_FSL_USDHC_NUM 2 +#endif +#endif + +/* I2C configs */ +#ifdef CONFIG_CMD_I2C +#define CONFIG_SYS_I2C_MXC +#define CONFIG_SYS_I2C_MXC_I2C1 /* enable I2C bus 1 */ +#define CONFIG_SYS_I2C_MXC_I2C2 /* enable I2C bus 2 */ +#define CONFIG_SYS_I2C_SPEED 100000 +#endif + +#define CONFIG_SYS_MMC_IMG_LOAD_PART 1 + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "script=boot.scr\0" \ + "image=zImage\0" \ + "console=ttymxc0\0" \ + "fdt_high=0xffffffff\0" \ + "initrd_high=0xffffffff\0" \ + "fdt_file=imx6ull-14x14-evk.dtb\0" \ + "fdt_addr=0x83000000\0" \ + "boot_fdt=try\0" \ + "ip_dyn=yes\0" \ + "videomode=video=ctfb:x:480,y:272,depth:24,pclk:108695,le:8,ri:4,up:2,lo:4,hs:41,vs:10,sync:0,vmode:0\0" \ + "mmcdev="__stringify(CONFIG_SYS_MMC_ENV_DEV)"\0" \ + "mmcpart=" __stringify(CONFIG_SYS_MMC_IMG_LOAD_PART) "\0" \ + "mmcroot=" CONFIG_MMCROOT " rootwait rw\0" \ + "mmcautodetect=yes\0" \ + "mmcargs=setenv bootargs console=${console},${baudrate} " \ + "root=${mmcroot}\0" \ + "loadbootscript=" \ + "fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \ + "bootscript=echo Running bootscript from mmc ...; " \ + "source\0" \ + "loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \ + "loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \ + "mmcboot=echo Booting from mmc ...; " \ + "run mmcargs; " \ + "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \ + "if run loadfdt; then " \ + "bootz ${loadaddr} - ${fdt_addr}; " \ + "else " \ + "if test ${boot_fdt} = try; then " \ + "bootz; " \ + "else " \ + "echo WARN: Cannot load the DT; " \ + "fi; " \ + "fi; " \ + "else " \ + "bootz; " \ + "fi;\0" \ + "netargs=setenv bootargs console=${console},${baudrate} " \ + "root=/dev/nfs " \ + "ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \ + "netboot=echo Booting from net ...; " \ + "run netargs; " \ + "if test ${ip_dyn} = yes; then " \ + "setenv get_cmd dhcp; " \ + "else " \ + "setenv get_cmd tftp; " \ + "fi; " \ + "${get_cmd} ${image}; " \ + "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \ + "if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \ + "bootz ${loadaddr} - ${fdt_addr}; " \ + "else " \ + "if test ${boot_fdt} = try; then " \ + "bootz; " \ + "else " \ + "echo WARN: Cannot load the DT; " \ + "fi; " \ + "fi; " \ + "else " \ + "bootz; " \ + "fi;\0" \ + +#define CONFIG_BOOTCOMMAND \ + "mmc dev ${mmcdev};" \ + "mmc dev ${mmcdev}; if mmc rescan; then " \ + "if run loadbootscript; then " \ + "run bootscript; " \ + "else " \ + "if run loadimage; then " \ + "run mmcboot; " \ + "else run netboot; " \ + "fi; " \ + "fi; " \ + "else run netboot; fi" + +/* Miscellaneous configurable options */ +#define CONFIG_SYS_MEMTEST_START 0x80000000 +#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MEMTEST_START + 0x8000000) + +#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR +#define CONFIG_SYS_HZ 1000 + +#define CONFIG_STACKSIZE SZ_128K + +/* Physical Memory Map */ +#define CONFIG_NR_DRAM_BANKS 1 +#define PHYS_SDRAM MMDC0_ARB_BASE_ADDR + +#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM +#define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR +#define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE + +#define CONFIG_SYS_INIT_SP_OFFSET \ + (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_ADDR \ + (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET) + +/* FLASH and environment organization */ +#define CONFIG_SYS_NO_FLASH + +#define CONFIG_SYS_MMC_ENV_DEV 1 /* USDHC2 */ +#define CONFIG_SYS_MMC_ENV_PART 0 /* user area */ +#define CONFIG_MMCROOT "/dev/mmcblk1p2" /* USDHC2 */ + +#define CONFIG_ENV_IS_IN_MMC +#define CONFIG_ENV_SIZE SZ_8K +#define CONFIG_ENV_OFFSET (12 * SZ_64K) + +#define CONFIG_CMD_BMODE + +#define CONFIG_IMX_THERMAL + +#define CONFIG_IOMUX_LPSR + +#define CONFIG_SOFT_SPI + +#endif -- 2.39.5