From 68964dbc838077c8ecd796fd43b0aa43bb309a50 Mon Sep 17 00:00:00 2001 From: Simon Glass Date: Mon, 3 Aug 2015 08:19:34 -0600 Subject: [PATCH] video: Remove the old parade driver We have a new one which uses driver model and device tree configuration. Remove the old one. Signed-off-by: Simon Glass --- drivers/video/Makefile | 1 - drivers/video/parade.c | 231 ------------------------------------ include/configs/peach-pi.h | 2 - include/configs/peach-pit.h | 2 - include/fdtdec.h | 1 - include/parade.h | 18 --- lib/fdtdec.c | 1 - 7 files changed, 256 deletions(-) delete mode 100644 drivers/video/parade.c delete mode 100644 include/parade.h diff --git a/drivers/video/Makefile b/drivers/video/Makefile index 599fe83b33..c2c4dfc57e 100644 --- a/drivers/video/Makefile +++ b/drivers/video/Makefile @@ -51,7 +51,6 @@ obj-$(CONFIG_VIDEO_VESA) += vesa_fb.o obj-$(CONFIG_FORMIKE) += formike.o obj-$(CONFIG_LG4573) += lg4573.o obj-$(CONFIG_AM335X_LCD) += am335x-fb.o -obj-$(CONFIG_VIDEO_PARADE) += parade.o obj-${CONFIG_VIDEO_TEGRA124} += tegra124/ diff --git a/drivers/video/parade.c b/drivers/video/parade.c deleted file mode 100644 index ae5097160f..0000000000 --- a/drivers/video/parade.c +++ /dev/null @@ -1,231 +0,0 @@ -/* - * Copyright (c) 2014 The Chromium OS Authors. All rights reserved. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -/* - * This file is a driver for Parade dP<->LVDS bridges. The original submission - * is for the ps8625 chip. - */ -#include -#include -#include -#include -#include - -/* - * Initialization of the chip is a process of writing certaing values into - * certain registers over i2c bus. The chip in fact responds to a range of - * addresses on the i2c bus, so for each written value three parameters are - * required: i2c address, register address and the actual value. - * - * The base address is derived from the device tree, only address offset is - * stored in the table below. - */ -/** - * struct reg_data() - data for a parade register write - * - * @addr_off offset from the i2c base address for parade - * @reg_addr register address to write - * @value value to be written - */ -struct reg_data { - uint8_t addr_off; - uint8_t reg; - uint8_t value; -} _packed; - -#define END_OF_TABLE 0xff /* Ficticious offset */ - -static const struct reg_data parade_values[] = { - {0x02, 0xa1, 0x01}, /* HPD low */ - /* - * SW setting - * [1:0] SW output 1.2V voltage is lower to 96% - */ - {0x04, 0x14, 0x01}, - /* - * RCO SS setting - * [5:4] = b01 0.5%, b10 1%, b11 1.5% - */ - {0x04, 0xe3, 0x20}, - {0x04, 0xe2, 0x80}, /* [7] RCO SS enable */ - /* - * RPHY Setting - * [3:2] CDR tune wait cycle before - * measure for fine tune b00: 1us, - * 01: 0.5us, 10:2us, 11:4us. - */ - {0x04, 0x8a, 0x0c}, - {0x04, 0x89, 0x08}, /* [3] RFD always on */ - /* - * CTN lock in/out: - * 20000ppm/80000ppm. Lock out 2 - * times. - */ - {0x04, 0x71, 0x2d}, - /* - * 2.7G CDR settings - * NOF=40LSB for HBR CDR setting - */ - {0x04, 0x7d, 0x07}, - {0x04, 0x7b, 0x00}, /* [1:0] Fmin=+4bands */ - {0x04, 0x7a, 0xfd}, /* [7:5] DCO_FTRNG=+-40% */ - /* - * 1.62G CDR settings - * [5:2]NOF=64LSB [1:0]DCO scale is 2/5 - */ - {0x04, 0xc0, 0x12}, - {0x04, 0xc1, 0x92}, /* Gitune=-37% */ - {0x04, 0xc2, 0x1c}, /* Fbstep=100% */ - {0x04, 0x32, 0x80}, /* [7] LOS signal disable */ - /* - * RPIO Setting - * [7:4] LVDS driver bias current : - * 75% (250mV swing) - */ - {0x04, 0x00, 0xb0}, - /* - * [7:6] Right-bar GPIO output strength is 8mA - */ - {0x04, 0x15, 0x40}, - /* EQ Training State Machine Setting */ - {0x04, 0x54, 0x10}, /* RCO calibration start */ - /* [4:0] MAX_LANE_COUNT set to one lane */ - {0x01, 0x02, 0x81}, - /* [4:0] LANE_COUNT_SET set to one lane */ - {0x01, 0x21, 0x81}, - {0x00, 0x52, 0x20}, - {0x00, 0xf1, 0x03}, /* HPD CP toggle enable */ - {0x00, 0x62, 0x41}, - /* Counter number, add 1ms counter delay */ - {0x00, 0xf6, 0x01}, - /* - * [6]PWM function control by - * DPCD0040f[7], default is PWM - * block always works. - */ - {0x00, 0x77, 0x06}, - /* - * 04h Adjust VTotal tolerance to - * fix the 30Hz no display issue - */ - {0x00, 0x4c, 0x04}, - /* DPCD00400='h00, Parade OUI = 'h001cf8 */ - {0x01, 0xc0, 0x00}, - {0x01, 0xc1, 0x1c}, /* DPCD00401='h1c */ - {0x01, 0xc2, 0xf8}, /* DPCD00402='hf8 */ - /* - * DPCD403~408 = ASCII code - * D2SLV5='h4432534c5635 - */ - {0x01, 0xc3, 0x44}, - {0x01, 0xc4, 0x32}, /* DPCD404 */ - {0x01, 0xc5, 0x53}, /* DPCD405 */ - {0x01, 0xc6, 0x4c}, /* DPCD406 */ - {0x01, 0xc7, 0x56}, /* DPCD407 */ - {0x01, 0xc8, 0x35}, /* DPCD408 */ - /* - * DPCD40A, Initial Code major revision - * '01' - */ - {0x01, 0xca, 0x01}, - /* DPCD40B, Initial Code minor revision '05' */ - {0x01, 0xcb, 0x05}, - /* DPCD720, Select internal PWM */ - {0x01, 0xa5, 0xa0}, - /* - * FFh for 100% PWM of brightness, 0h for 0% - * brightness - */ - {0x01, 0xa7, 0xff}, - /* - * Set LVDS output as 6bit-VESA mapping, - * single LVDS channel - */ - {0x01, 0xcc, 0x13}, - /* Enable SSC set by register */ - {0x02, 0xb1, 0x20}, - /* - * Set SSC enabled and +/-1% central - * spreading - */ - {0x04, 0x10, 0x16}, - /* MPU Clock source: LC => RCO */ - {0x04, 0x59, 0x60}, - {0x04, 0x54, 0x14}, /* LC -> RCO */ - {0x02, 0xa1, 0x91}, /* HPD high */ - {END_OF_TABLE} -}; - -/** - * Write values table into the Parade eDP bridge - * - * @return 0 on success, non-0 on failure - */ - -static int parade_write_regs(int base_addr, const struct reg_data *table) -{ - int ret = 0; - - while (!ret && (table->addr_off != END_OF_TABLE)) { - ret = i2c_write(base_addr + table->addr_off, - table->reg, 1, - (uint8_t *)&table->value, - sizeof(table->value)); - table++; - } - return ret; -} - -int parade_init(const void *blob) -{ - struct gpio_desc rst_gpio; - struct gpio_desc slp_gpio; - int bus, old_bus; - int parent; - int node; - int addr; - int ret; - - node = fdtdec_next_compatible(blob, 0, COMPAT_PARADE_PS8625); - if (node < 0) - return 0; - - parent = fdt_parent_offset(blob, node); - if (parent < 0) { - debug("%s: Could not find parent i2c node\n", __func__); - return -1; - } - addr = fdtdec_get_int(blob, node, "reg", -1); - if (addr < 0) { - debug("%s: Could not find i2c address\n", __func__); - return -1; - } - - gpio_request_by_name_nodev(blob, node, "sleep-gpio", 0, &slp_gpio, - GPIOD_IS_OUT | GPIOD_IS_OUT_ACTIVE); - - mdelay(10); - - gpio_request_by_name_nodev(blob, node, "reset-gpio", 0, &rst_gpio, - GPIOD_IS_OUT | GPIOD_IS_OUT_ACTIVE); - - bus = i2c_get_bus_num_fdt(parent); - old_bus = i2c_get_bus_num(); - - debug("%s: Using i2c bus %d\n", __func__, bus); - - /* - * TODO(sjg@chromium.org): Hmmm we seem to need some sort of delay - * here. - */ - mdelay(40); - i2c_set_bus_num(bus); - ret = parade_write_regs(addr, parade_values); - - i2c_set_bus_num(old_bus); - - return ret; -} diff --git a/include/configs/peach-pi.h b/include/configs/peach-pi.h index b97faf2c3b..0f5e9feeac 100644 --- a/include/configs/peach-pi.h +++ b/include/configs/peach-pi.h @@ -32,8 +32,6 @@ #define CONFIG_SYS_PROMPT "Peach-Pi # " #define CONFIG_IDENT_STRING " for Peach-Pi" -#define CONFIG_VIDEO_PARADE - /* Display */ #define CONFIG_LCD #ifdef CONFIG_LCD diff --git a/include/configs/peach-pit.h b/include/configs/peach-pit.h index beb65b007d..f2594345c3 100644 --- a/include/configs/peach-pit.h +++ b/include/configs/peach-pit.h @@ -32,8 +32,6 @@ #define CONFIG_SYS_PROMPT "Peach-Pit # " #define CONFIG_IDENT_STRING " for Peach-Pit" -#define CONFIG_VIDEO_PARADE - /* DRAM Memory Banks */ #define CONFIG_NR_DRAM_BANKS 4 #define SDRAM_BANK_SIZE (512UL << 20UL) /* 512 MB */ diff --git a/include/fdtdec.h b/include/fdtdec.h index 12dc5fd2fa..b994f2c783 100644 --- a/include/fdtdec.h +++ b/include/fdtdec.h @@ -172,7 +172,6 @@ enum fdt_compat_id { COMPAT_SANDBOX_LCD_SDL, /* Sandbox LCD emulation with SDL */ COMPAT_NXP_PTN3460, /* NXP PTN3460 DP/LVDS bridge */ COMPAT_SAMSUNG_EXYNOS_SYSMMU, /* Exynos sysmmu */ - COMPAT_PARADE_PS8625, /* Parade PS8622 EDP->LVDS bridge */ COMPAT_INTEL_MICROCODE, /* Intel microcode update */ COMPAT_MEMORY_SPD, /* Memory SPD information */ COMPAT_INTEL_PANTHERPOINT_AHCI, /* Intel Pantherpoint AHCI */ diff --git a/include/parade.h b/include/parade.h deleted file mode 100644 index 887f56dcf2..0000000000 --- a/include/parade.h +++ /dev/null @@ -1,18 +0,0 @@ -/* - * (C) Copyright 2012 Samsung Electronics - * Donghwa Lee - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#ifndef __PARADE_H__ -#define __PARADE_H__ - -/* Initialize the Parade dP<->LVDS bridge if present */ -#ifdef CONFIG_VIDEO_PARADE -int parade_init(const void *blob); -#else -static inline int parade_init(const void *blob) { return -1; } -#endif - -#endif /* __PARADE_H__ */ diff --git a/lib/fdtdec.c b/lib/fdtdec.c index 3d20f388e0..527916311b 100644 --- a/lib/fdtdec.c +++ b/lib/fdtdec.c @@ -64,7 +64,6 @@ static const char * const compat_names[COMPAT_COUNT] = { COMPAT(SANDBOX_LCD_SDL, "sandbox,lcd-sdl"), COMPAT(COMPAT_NXP_PTN3460, "nxp,ptn3460"), COMPAT(SAMSUNG_EXYNOS_SYSMMU, "samsung,sysmmu-v3.3"), - COMPAT(PARADE_PS8625, "parade,ps8625"), COMPAT(INTEL_MICROCODE, "intel,microcode"), COMPAT(MEMORY_SPD, "memory-spd"), COMPAT(INTEL_PANTHERPOINT_AHCI, "intel,pantherpoint-ahci"), -- 2.39.5