From 6ff4137f2ad640e4fc8ea1b0455161ddff1f6730 Mon Sep 17 00:00:00 2001 From: Mike Frysinger Date: Wed, 11 Feb 2009 14:12:34 -0500 Subject: [PATCH] doc/README.enetaddr: document proper MAC usage Signed-off-by: Mike Frysinger CC: Ben Warren --- doc/README.enetaddr | 99 +++++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 99 insertions(+) create mode 100644 doc/README.enetaddr diff --git a/doc/README.enetaddr b/doc/README.enetaddr new file mode 100644 index 0000000000..1d75aa3876 --- /dev/null +++ b/doc/README.enetaddr @@ -0,0 +1,99 @@ +--------------------------------- + Ethernet Address (MAC) Handling +--------------------------------- + +There are a variety of places in U-Boot where the MAC address is used, parsed, +and stored. This document covers proper usage of each location and the moving +of data between them. + +----------- + Locations +----------- + +Here are the places where MAC addresses might be stored: + + - board-specific location (eeprom, dedicated flash, ...) + Note: only used when mandatory due to hardware design etc... + + - environment ("ethaddr", "eth1addr", ...) (see CONFIG_ETHADDR) + Note: this is the preferred way to permanently store MAC addresses + + - ethernet data (struct eth_device -> enetaddr) + Note: these are temporary copies of the MAC address which exist only + after the respective init steps have run and only to make usage + in other places easier (to avoid constant env lookup/parsing) + + - struct bd_info and/or device tree + Note: these are temporary copies of the MAC address only for the + purpose of passing this information to an OS kernel we are about + to boot + +------- + Usage +------- + +If the hardware design mandates that the MAC address is stored in some special +place (like EEPROM etc...), then the board specific init code (such as the +board-specific misc_init_r() function) is responsible for locating the MAC +address(es) and initializing the respective environment variable(s) from it. +Note that this shall be done if, and only if, the environment does not already +contain these environment variables, i.e. existing variable definitions must +not be overwritten. + +During runtime, the ethernet layer will use the environment variables to sync +the MAC addresses to the ethernet structures. All ethernet driver code should +then only use the enetaddr member of the eth_device structure. This is done +on every network command, so the ethernet copies will stay in sync. + +Any other code that wishes to access the MAC address should query the +environment directly. The helper functions documented below should make +working with this storage much smoother. + +--------- + Helpers +--------- + +To assist in the management of these layers, a few helper functions exist. You +should use these rather than attempt to do any kind of parsing/manipulation +yourself as many common errors have arisen in the past. + + * void eth_parse_enetaddr(const char *addr, uchar *enetaddr); + +Convert a string representation of a MAC address to the binary version. +char *addr = "00:11:22:33:44:55"; +uchar enetaddr[6]; +eth_parse_enetaddr(addr, enetaddr); +/* enetaddr now equals { 0x00, 0x11, 0x22, 0x33, 0x44, 0x55 } */ + + * int eth_getenv_enetaddr(char *name, uchar *enetaddr); + +Look up an environment variable and convert the stored address. If the address +is valid, then the function returns 1. Otherwise, the function returns 0. In +all cases, the enetaddr memory is initialized. If the env var is not found, +then it is set to all zeros. The common function is_valid_ether_addr() is used +to determine address validity. +uchar enetaddr[6]; +if (!eth_getenv_enetaddr("ethaddr", enetaddr)) { + /* "ethaddr" is not set in the environment */ + ... try and setup "ethaddr" in the env ... +} +/* enetaddr is now set to the value stored in the ethaddr env var */ + + * int eth_setenv_enetaddr(char *name, const uchar *enetaddr); + +Store the MAC address into the named environment variable. The return value is +the same as the setenv() function. +uchar enetaddr[6] = { 0x00, 0x11, 0x22, 0x33, 0x44, 0x55 }; +eth_setenv_enetaddr("ethaddr", enetaddr); +/* the "ethaddr" env var should now be set to "00:11:22:33:44:55" */ + + * the %pM format modifier + +The %pM format modifier can be used with any standard printf function to format +the binary 6 byte array representation of a MAC address. +uchar enetaddr[6] = { 0x00, 0x11, 0x22, 0x33, 0x44, 0x55 }; +printf("The MAC is %pM\n", enetaddr); + +char buf[20]; +sprintf(buf, "%pM", enetaddr); +/* the buf variable is now set to "00:11:22:33:44:55" */ -- 2.39.5