From 8b0044ff5942943eaa49935f49d5006b346a60f8 Mon Sep 17 00:00:00 2001 From: Oleksandr G Zhadan Date: Wed, 29 Apr 2015 16:57:39 -0400 Subject: [PATCH] powerpc/mpc85xx: Add board support for ucp1020 New QorIQ p1020 based board support from Arcturus Networks Inc. http://www.arcturusnetworks.com/products/ucp1020/ Signed-off-by: Michael Durrant Signed-off-by: Oleksandr G Zhadan [York Sun: remove patman tags from commit message] Reviewed-by: York Sun --- arch/powerpc/cpu/mpc85xx/Kconfig | 4 + board/Arcturus/ucp1020/Kconfig | 44 ++ board/Arcturus/ucp1020/MAINTAINERS | 7 + board/Arcturus/ucp1020/Makefile | 33 + board/Arcturus/ucp1020/README | 54 ++ board/Arcturus/ucp1020/cmd_arc.c | 231 ++++++ board/Arcturus/ucp1020/ddr.c | 161 ++++ board/Arcturus/ucp1020/law.c | 25 + board/Arcturus/ucp1020/spl.c | 126 ++++ board/Arcturus/ucp1020/spl_minimal.c | 67 ++ board/Arcturus/ucp1020/tlb.c | 101 +++ board/Arcturus/ucp1020/ucp1020.c | 363 +++++++++ board/Arcturus/ucp1020/ucp1020.h | 44 ++ configs/UCP1020_SPIFLASH_defconfig | 6 + configs/UCP1020_defconfig | 5 + include/configs/UCP1020.h | 1027 ++++++++++++++++++++++++++ 16 files changed, 2298 insertions(+) create mode 100644 board/Arcturus/ucp1020/Kconfig create mode 100644 board/Arcturus/ucp1020/MAINTAINERS create mode 100644 board/Arcturus/ucp1020/Makefile create mode 100644 board/Arcturus/ucp1020/README create mode 100644 board/Arcturus/ucp1020/cmd_arc.c create mode 100644 board/Arcturus/ucp1020/ddr.c create mode 100644 board/Arcturus/ucp1020/law.c create mode 100644 board/Arcturus/ucp1020/spl.c create mode 100644 board/Arcturus/ucp1020/spl_minimal.c create mode 100644 board/Arcturus/ucp1020/tlb.c create mode 100644 board/Arcturus/ucp1020/ucp1020.c create mode 100644 board/Arcturus/ucp1020/ucp1020.h create mode 100644 configs/UCP1020_SPIFLASH_defconfig create mode 100644 configs/UCP1020_defconfig create mode 100644 include/configs/UCP1020.h diff --git a/arch/powerpc/cpu/mpc85xx/Kconfig b/arch/powerpc/cpu/mpc85xx/Kconfig index b70d9e9e32..aff5fdb514 100644 --- a/arch/powerpc/cpu/mpc85xx/Kconfig +++ b/arch/powerpc/cpu/mpc85xx/Kconfig @@ -151,6 +151,9 @@ config TARGET_XPEDITE537X config TARGET_XPEDITE550X bool "Support xpedite550x" +config TARGET_UCP1020 + bool "Support uCP1020" + endchoice source "board/freescale/b4860qds/Kconfig" @@ -192,5 +195,6 @@ source "board/stx/stxssa/Kconfig" source "board/xes/xpedite520x/Kconfig" source "board/xes/xpedite537x/Kconfig" source "board/xes/xpedite550x/Kconfig" +source "board/Arcturus/ucp1020/Kconfig" endmenu diff --git a/board/Arcturus/ucp1020/Kconfig b/board/Arcturus/ucp1020/Kconfig new file mode 100644 index 0000000000..feca03aeef --- /dev/null +++ b/board/Arcturus/ucp1020/Kconfig @@ -0,0 +1,44 @@ +if TARGET_UCP1020 + +config SYS_BOARD + string + default "ucp1020" + +config SYS_VENDOR + string + default "Arcturus" + +config SYS_CONFIG_NAME + string + default "UCP1020" + +config SPI_FLASH + bool + default y + +config SPI_PCI + bool + default y + +choice + prompt "Target image select" + +config TARGET_UCP1020_NOR + bool "NOR flash u-boot image" + +config TARGET_UCP1020_SPIFLASH + bool "SPI flash u-boot image" + +endchoice + +if TARGET_UCP1020_SPIFLASH +config UCBOOT + bool + default y + +config SPIFLASH + bool + default y +endif + +endif diff --git a/board/Arcturus/ucp1020/MAINTAINERS b/board/Arcturus/ucp1020/MAINTAINERS new file mode 100644 index 0000000000..e4a4718188 --- /dev/null +++ b/board/Arcturus/ucp1020/MAINTAINERS @@ -0,0 +1,7 @@ +UCP1020 BOARD +M: Oleksandr Zhadan and Michael Durrant +S: Maintained +F: board/Arcturus/ucp1020/ +F: include/configs/UCP1020.h +F: configs/UCP1020_defconfig +F: configs/UCP1020_SPIFLASH_defconfig diff --git a/board/Arcturus/ucp1020/Makefile b/board/Arcturus/ucp1020/Makefile new file mode 100644 index 0000000000..35c88b98a9 --- /dev/null +++ b/board/Arcturus/ucp1020/Makefile @@ -0,0 +1,33 @@ +# +# Copyright 2013-2015 Arcturus Networks, Inc. +# based on board/freescale/p1_p2_rdb_pc/Makefile +# original copyright follows: +# Copyright 2010-2011 Freescale Semiconductor, Inc. +# +# SPDX-License-Identifier: GPL-2.0+ +# + +MINIMAL= + +ifdef CONFIG_SPL_BUILD +ifdef CONFIG_SPL_INIT_MINIMAL +MINIMAL=y +endif +endif + +ifdef MINIMAL + +obj-y += spl_minimal.o tlb.o law.o + +else +ifdef CONFIG_SPL_BUILD +obj-y += spl.o +endif + +obj-y += ucp1020.o +obj-y += ddr.o +obj-y += law.o +obj-y += tlb.o +obj-y += cmd_arc.o + +endif diff --git a/board/Arcturus/ucp1020/README b/board/Arcturus/ucp1020/README new file mode 100644 index 0000000000..555c4ef79f --- /dev/null +++ b/board/Arcturus/ucp1020/README @@ -0,0 +1,54 @@ +The uCP1020 product family (ucp1020) is an Arcturus Networks Inc. System on Modules +product featuring a Freescale P1020 CPU, optionally populated with 1, 2 or 3 Gig-Ethernet PHYs, +DDR3, NOR Flash, eMMC NAND Flash and/or SPI Flash. + +Information on the generic product family can be found here: + http://www.arcturusnetworks.com/products/ucp1020 + +The UCP1020 several configurable options +======================================== + +- the selection of populated phy(s): + KSZ9031 (current default for eTSEC 1 and 3) + +- the selection of boot location: + SPI Flash or NOR flash + +The UCP1020 includes 2 default configurations +============================================= +NOR boot image: + configs/UCP1020_defconfig +SPI boot image: + configs/UCP1020_SPIFLASH_defconfig + +The UCP1020 adds an additional command in cmd_arc.c to access and program +SPI resident factory defaults for serial number, and 1, 2 or 3 Ethernet +HW Addresses. + + +Build example +============= + +make distclean +make UCP1020_defconfig +make + +Default Scripts +=============== +A default upgrade scripts is included in the default environment variable example: + +B$ run tftpflash + +Dual Environment +================ + +This build enables dual / failover environment environment. + +NOR Flash Partition declarations and scripts +============================================ +Several scripts are available to allow TFTP of images and programming directly +into defined NOR flash partitions. Examples: + +B$ run program0 +B$ run program1 +B$ run program2 diff --git a/board/Arcturus/ucp1020/cmd_arc.c b/board/Arcturus/ucp1020/cmd_arc.c new file mode 100644 index 0000000000..fa6b4853f9 --- /dev/null +++ b/board/Arcturus/ucp1020/cmd_arc.c @@ -0,0 +1,231 @@ +/* + * Command for accessing Arcturus factory environment. + * + * Copyright 2013-2015 Arcturus Networks Inc. + * http://www.arcturusnetworks.com/products/ucp1020/ + * by Oleksandr G Zhadan et al. + * + * SPDX-License-Identifier: GPL-2.0+ BSD-3-Clause + * + */ + +#include +#include +#include +#include + +#include + +#ifndef CONFIG_SF_DEFAULT_SPEED +# define CONFIG_SF_DEFAULT_SPEED 1000000 +#endif +#ifndef CONFIG_SF_DEFAULT_MODE +# define CONFIG_SF_DEFAULT_MODE SPI_MODE0 +#endif +#ifndef CONFIG_SF_DEFAULT_CS +# define CONFIG_SF_DEFAULT_CS 0 +#endif +#ifndef CONFIG_SF_DEFAULT_BUS +# define CONFIG_SF_DEFAULT_BUS 0 +#endif + +#define MAX_SERIAL_SIZE 15 +#define MAX_HWADDR_SIZE 17 + +#define FIRM_ADDR1 (0x200 - sizeof(smac)) +#define FIRM_ADDR2 (0x400 - sizeof(smac)) +#define FIRM_ADDR3 (CONFIG_ENV_SECT_SIZE + 0x200 - sizeof(smac)) +#define FIRM_ADDR4 (CONFIG_ENV_SECT_SIZE + 0x400 - sizeof(smac)) + +static struct spi_flash *flash; +char smac[4][18]; + +static int ishwaddr(char *hwaddr) +{ + if (strlen(hwaddr) == MAX_HWADDR_SIZE) + if (hwaddr[2] == ':' && + hwaddr[5] == ':' && + hwaddr[8] == ':' && + hwaddr[11] == ':' && + hwaddr[14] == ':') + return 0; + return -1; +} + +static int set_arc_product(int argc, char *const argv[]) +{ + int err = 0; + char *mystrerr = "ERROR: Failed to save factory info in spi location"; + + if (argc != 5) + return -1; + + /* Check serial number */ + if (strlen(argv[1]) != MAX_SERIAL_SIZE) + return -1; + + /* Check HWaddrs */ + if (ishwaddr(argv[2]) || ishwaddr(argv[3]) || ishwaddr(argv[4])) + return -1; + + strcpy(smac[3], argv[1]); + strcpy(smac[2], argv[2]); + strcpy(smac[1], argv[3]); + strcpy(smac[0], argv[4]); + + flash = spi_flash_probe(CONFIG_ENV_SPI_BUS, CONFIG_ENV_SPI_CS, + CONFIG_ENV_SPI_MAX_HZ, CONFIG_ENV_SPI_MODE); + + /* + * Save factory defaults + */ + + if (spi_flash_write(flash, FIRM_ADDR1, sizeof(smac), smac)) { + printf("%s: %s [1]\n", __func__, mystrerr); + err++; + } + if (spi_flash_write(flash, FIRM_ADDR2, sizeof(smac), smac)) { + printf("%s: %s [2]\n", __func__, mystrerr); + err++; + } + + if (spi_flash_write(flash, FIRM_ADDR3, sizeof(smac), smac)) { + printf("%s: %s [3]\n", __func__, mystrerr); + err++; + } + + if (spi_flash_write(flash, FIRM_ADDR4, sizeof(smac), smac)) { + printf("%s: %s [4]\n", __func__, mystrerr); + err++; + } + + if (err == 4) { + printf("%s: %s [ALL]\n", __func__, mystrerr); + return -2; + } + + return 0; +} + +int get_arc_info(void) +{ + int location = 1; + char *myerr = "ERROR: Failed to read all 4 factory info spi locations"; + + flash = spi_flash_probe(CONFIG_ENV_SPI_BUS, CONFIG_ENV_SPI_CS, + CONFIG_ENV_SPI_MAX_HZ, CONFIG_ENV_SPI_MODE); + + if (spi_flash_read(flash, FIRM_ADDR1, sizeof(smac), smac)) { + location++; + if (spi_flash_read(flash, FIRM_ADDR2, sizeof(smac), smac)) { + location++; + if (spi_flash_read(flash, FIRM_ADDR3, sizeof(smac), + smac)) { + location++; + if (spi_flash_read(flash, FIRM_ADDR4, + sizeof(smac), smac)) { + printf("%s: %s\n", __func__, myerr); + return -2; + } + } + } + } + if (smac[3][0] != 0) { + if (location > 1) + printf("Using region %d\n", location); + printf("SERIAL: "); + if (smac[3][0] == 0xFF) { + printf("\t\n"); + } else { + printf("\t%s\n", smac[3]); + setenv("SERIAL", smac[3]); + } + } + + if (strcmp(smac[2], "00:00:00:00:00:00") == 0) + return 0; + + printf("HWADDR0:"); + if (smac[2][0] == 0xFF) { + printf("\t\n"); + } else { + char *ret = getenv("ethaddr"); + + if (strcmp(ret, __stringify(CONFIG_ETHADDR)) == 0) { + setenv("ethaddr", smac[2]); + printf("\t%s (factory)\n", smac[2]); + } else { + printf("\t%s\n", ret); + } + } + + if (strcmp(smac[1], "00:00:00:00:00:00") == 0) { + setenv("eth1addr", smac[2]); + setenv("eth2addr", smac[2]); + return 0; + } + + printf("HWADDR1:"); + if (smac[1][0] == 0xFF) { + printf("\t\n"); + } else { + char *ret = getenv("eth1addr"); + + if (strcmp(ret, __stringify(CONFIG_ETH1ADDR)) == 0) { + setenv("eth1addr", smac[1]); + printf("\t%s (factory)\n", smac[1]); + } else { + printf("\t%s\n", ret); + } + } + + if (strcmp(smac[0], "00:00:00:00:00:00") == 0) { + setenv("eth2addr", smac[1]); + return 0; + } + + printf("HWADDR2:"); + if (smac[0][0] == 0xFF) { + printf("\t\n"); + } else { + char *ret = getenv("eth2addr"); + + if (strcmp(ret, __stringify(CONFIG_ETH2ADDR)) == 0) { + setenv("eth2addr", smac[0]); + printf("\t%s (factory)\n", smac[0]); + } else { + printf("\t%s\n", ret); + } + } + + return 0; +} + +static int do_arc_cmd(cmd_tbl_t *cmdtp, int flag, int argc, char *const argv[]) +{ + const char *cmd; + int ret = -1; + + cmd = argv[1]; + --argc; + ++argv; + + if (strcmp(cmd, "product") == 0) { + ret = set_arc_product(argc, argv); + goto done; + } + if (strcmp(cmd, "info") == 0) { + ret = get_arc_info(); + goto done; + } +done: + if (ret == -1) + return CMD_RET_USAGE; + + return ret; +} + +U_BOOT_CMD(arc, 6, 1, do_arc_cmd, + "Arcturus product command sub-system", + "product serial hwaddr0 hwaddr1 hwaddr2 - save Arcturus factory env\n" + "info - show Arcturus factory env\n\n"); diff --git a/board/Arcturus/ucp1020/ddr.c b/board/Arcturus/ucp1020/ddr.c new file mode 100644 index 0000000000..42fbae058d --- /dev/null +++ b/board/Arcturus/ucp1020/ddr.c @@ -0,0 +1,161 @@ +/* + * Copyright 2013-2015 Arcturus Networks, Inc. + * http://www.arcturusnetworks.com/products/ucp1020/ + * based on board/freescale/p1_p2_rdb_pc/spl.c + * original copyright follows: + * Copyright 2013 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include +#include +#include +#include +#include +#include +#include +#include + +#ifdef CONFIG_SYS_DDR_RAW_TIMING +#if defined(CONFIG_UCP1020) || defined(CONFIG_UCP1020T1) +/* + * Micron MT41J128M16HA-15E + * */ +dimm_params_t ddr_raw_timing = { + .n_ranks = 1, + .rank_density = 536870912u, + .capacity = 536870912u, + .primary_sdram_width = 32, + .ec_sdram_width = 8, + .registered_dimm = 0, + .mirrored_dimm = 0, + .n_row_addr = 14, + .n_col_addr = 10, + .n_banks_per_sdram_device = 8, + .edc_config = 2, + .burst_lengths_bitmask = 0x0c, + + .tckmin_x_ps = 1650, + .caslat_x = 0x7e << 4, /* 5,6,7,8,9,10 */ + .taa_ps = 14050, + .twr_ps = 15000, + .trcd_ps = 13500, + .trrd_ps = 75000, + .trp_ps = 13500, + .tras_ps = 40000, + .trc_ps = 49500, + .trfc_ps = 160000, + .twtr_ps = 75000, + .trtp_ps = 75000, + .refresh_rate_ps = 7800000, + .tfaw_ps = 30000, +}; + +#else +#error Missing raw timing data for this board +#endif + +int fsl_ddr_get_dimm_params(dimm_params_t *pdimm, + unsigned int controller_number, + unsigned int dimm_number) +{ + const char dimm_model[] = "Fixed DDR on board"; + + if ((controller_number == 0) && (dimm_number == 0)) { + memcpy(pdimm, &ddr_raw_timing, sizeof(dimm_params_t)); + memset(pdimm->mpart, 0, sizeof(pdimm->mpart)); + memcpy(pdimm->mpart, dimm_model, sizeof(dimm_model) - 1); + } + + return 0; +} +#endif /* CONFIG_SYS_DDR_RAW_TIMING */ + +#ifdef CONFIG_SYS_DDR_CS0_BNDS +/* Fixed sdram init -- doesn't use serial presence detect. */ +phys_size_t fixed_sdram(void) +{ + sys_info_t sysinfo; + char buf[32]; + size_t ddr_size; + fsl_ddr_cfg_regs_t ddr_cfg_regs = { + .cs[0].bnds = CONFIG_SYS_DDR_CS0_BNDS, + .cs[0].config = CONFIG_SYS_DDR_CS0_CONFIG, + .cs[0].config_2 = CONFIG_SYS_DDR_CS0_CONFIG_2, +#if CONFIG_CHIP_SELECTS_PER_CTRL > 1 + .cs[1].bnds = CONFIG_SYS_DDR_CS1_BNDS, + .cs[1].config = CONFIG_SYS_DDR_CS1_CONFIG, + .cs[1].config_2 = CONFIG_SYS_DDR_CS1_CONFIG_2, +#endif + .timing_cfg_3 = CONFIG_SYS_DDR_TIMING_3, + .timing_cfg_0 = CONFIG_SYS_DDR_TIMING_0, + .timing_cfg_1 = CONFIG_SYS_DDR_TIMING_1, + .timing_cfg_2 = CONFIG_SYS_DDR_TIMING_2, + .ddr_sdram_cfg = CONFIG_SYS_DDR_CONTROL, + .ddr_sdram_cfg_2 = CONFIG_SYS_DDR_CONTROL_2, + .ddr_sdram_mode = CONFIG_SYS_DDR_MODE_1, + .ddr_sdram_mode_2 = CONFIG_SYS_DDR_MODE_2, + .ddr_sdram_md_cntl = CONFIG_SYS_DDR_MODE_CONTROL, + .ddr_sdram_interval = CONFIG_SYS_DDR_INTERVAL, + .ddr_data_init = CONFIG_SYS_DDR_DATA_INIT, + .ddr_sdram_clk_cntl = CONFIG_SYS_DDR_CLK_CTRL, + .ddr_init_addr = CONFIG_SYS_DDR_INIT_ADDR, + .ddr_init_ext_addr = CONFIG_SYS_DDR_INIT_EXT_ADDR, + .timing_cfg_4 = CONFIG_SYS_DDR_TIMING_4, + .timing_cfg_5 = CONFIG_SYS_DDR_TIMING_5, + .ddr_zq_cntl = CONFIG_SYS_DDR_ZQ_CONTROL, + .ddr_wrlvl_cntl = CONFIG_SYS_DDR_WRLVL_CONTROL, + .ddr_sr_cntr = CONFIG_SYS_DDR_SR_CNTR, + .ddr_sdram_rcw_1 = CONFIG_SYS_DDR_RCW_1, + .ddr_sdram_rcw_2 = CONFIG_SYS_DDR_RCW_2 + }; + + get_sys_info(&sysinfo); + printf("Configuring DDR for %s MT/s data rate\n", + strmhz(buf, sysinfo.freq_ddrbus)); + + ddr_size = CONFIG_SYS_SDRAM_SIZE * 1024 * 1024; + + fsl_ddr_set_memctl_regs(&ddr_cfg_regs, 0, 0); + + if (set_ddr_laws(CONFIG_SYS_DDR_SDRAM_BASE, + ddr_size, LAW_TRGT_IF_DDR_1) < 0) { + printf("ERROR setting Local Access Windows for DDR\n"); + return 0; + }; + + return ddr_size; +} +#endif + +void fsl_ddr_board_options(memctl_options_t *popts, + dimm_params_t *pdimm, + unsigned int ctrl_num) +{ + int i; + + popts->clk_adjust = 6; + popts->cpo_override = 0x1f; + popts->write_data_delay = 2; + popts->half_strength_driver_enable = 1; + /* Write leveling override */ + popts->wrlvl_en = 1; + popts->wrlvl_override = 1; + popts->wrlvl_sample = 0xf; + popts->wrlvl_start = 0x8; + popts->trwt_override = 1; + popts->trwt = 0; + + if (pdimm->primary_sdram_width == 64) + popts->data_bus_width = 0; + else if (pdimm->primary_sdram_width == 32) + popts->data_bus_width = 1; + else + printf("Error in DDR bus width configuration!\n"); + + for (i = 0; i < CONFIG_CHIP_SELECTS_PER_CTRL; i++) { + popts->cs_local_opts[i].odt_rd_cfg = FSL_DDR_ODT_NEVER; + popts->cs_local_opts[i].odt_wr_cfg = FSL_DDR_ODT_CS; + } +} diff --git a/board/Arcturus/ucp1020/law.c b/board/Arcturus/ucp1020/law.c new file mode 100644 index 0000000000..7d40905b56 --- /dev/null +++ b/board/Arcturus/ucp1020/law.c @@ -0,0 +1,25 @@ +/* + * Copyright 2013-2015 Arcturus Networks, Inc. + * http://www.arcturusnetworks.com/products/ucp1020/ + * based on board/freescale/p1_p2_rdb_pc/spl.c + * original copyright follows: + * Copyright 2013 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include +#include +#include + +struct law_entry law_table[] = { +#ifdef CONFIG_VSC7385_ENET + SET_LAW(CONFIG_SYS_VSC7385_BASE_PHYS, LAW_SIZE_1M, LAW_TRGT_IF_LBC), +#endif + SET_LAW(CONFIG_SYS_FLASH_BASE_PHYS, LAW_SIZE_64M, LAW_TRGT_IF_LBC), +#ifdef CONFIG_SYS_NAND_BASE_PHYS + SET_LAW(CONFIG_SYS_NAND_BASE_PHYS, LAW_SIZE_32K, LAW_TRGT_IF_LBC), +#endif +}; + +int num_law_entries = ARRAY_SIZE(law_table); diff --git a/board/Arcturus/ucp1020/spl.c b/board/Arcturus/ucp1020/spl.c new file mode 100644 index 0000000000..236b0d0de5 --- /dev/null +++ b/board/Arcturus/ucp1020/spl.c @@ -0,0 +1,126 @@ +/* + * Copyright 2013-2015 Arcturus Networks, Inc. + * http://www.arcturusnetworks.com/products/ucp1020/ + * based on board/freescale/p1_p2_rdb_pc/spl.c + * original copyright follows: + * Copyright 2013 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include +#include +#include +#include +#include +#include +#include +#include + +DECLARE_GLOBAL_DATA_PTR; + +static const u32 sysclk_tbl[] = { + 66666000, 7499900, 83332500, 8999900, + 99999000, 11111000, 12499800, 13333200 +}; + +phys_size_t get_effective_memsize(void) +{ + return CONFIG_SYS_L2_SIZE; +} + +void board_init_f(ulong bootflag) +{ + u32 plat_ratio, bus_clk; + ccsr_gur_t *gur = (void *)CONFIG_SYS_MPC85xx_GUTS_ADDR; + + console_init_f(); + + /* Set pmuxcr to allow both i2c1 and i2c2 */ + setbits_be32(&gur->pmuxcr, in_be32(&gur->pmuxcr) | 0x1000); + setbits_be32(&gur->pmuxcr, + in_be32(&gur->pmuxcr) | MPC85xx_PMUXCR_SD_DATA); + + /* Read back the register to synchronize the write. */ + in_be32(&gur->pmuxcr); + +#ifdef CONFIG_SPL_SPI_BOOT + clrbits_be32(&gur->pmuxcr, MPC85xx_PMUXCR_SD_DATA); +#endif + + /* initialize selected port with appropriate baud rate */ + plat_ratio = in_be32(&gur->porpllsr) & MPC85xx_PORPLLSR_PLAT_RATIO; + plat_ratio >>= 1; + bus_clk = CONFIG_SYS_CLK_FREQ * plat_ratio; + gd->bus_clk = bus_clk; + + NS16550_init((NS16550_t)CONFIG_SYS_NS16550_COM1, + bus_clk / 16 / CONFIG_BAUDRATE); +#ifdef CONFIG_SPL_MMC_BOOT + puts("\nSD boot...\n"); +#elif defined(CONFIG_SPL_SPI_BOOT) + puts("\nSPI Flash boot...\n"); +#endif + + /* copy code to RAM and jump to it - this should not return */ + /* NOTE - code has to be copied out of NAND buffer before + * other blocks can be read. + */ + relocate_code(CONFIG_SPL_RELOC_STACK, 0, CONFIG_SPL_RELOC_TEXT_BASE); +} + +void board_init_r(gd_t *gd, ulong dest_addr) +{ + /* Pointer is writable since we allocated a register for it */ + gd = (gd_t *)CONFIG_SPL_GD_ADDR; + bd_t *bd; + + memset(gd, 0, sizeof(gd_t)); + bd = (bd_t *)(CONFIG_SPL_GD_ADDR + sizeof(gd_t)); + memset(bd, 0, sizeof(bd_t)); + gd->bd = bd; + bd->bi_memstart = CONFIG_SYS_INIT_L2_ADDR; + bd->bi_memsize = CONFIG_SYS_L2_SIZE; + + probecpu(); + get_clocks(); + mem_malloc_init(CONFIG_SPL_RELOC_MALLOC_ADDR, + CONFIG_SPL_RELOC_MALLOC_SIZE); + +#ifndef CONFIG_SPL_NAND_BOOT + env_init(); +#endif +#ifdef CONFIG_SPL_MMC_BOOT + mmc_initialize(bd); +#endif + /* relocate environment function pointers etc. */ +#ifdef CONFIG_SPL_NAND_BOOT + nand_spl_load_image(CONFIG_ENV_OFFSET, CONFIG_ENV_SIZE, + (uchar *)CONFIG_ENV_ADDR); + gd->env_addr = (ulong)(CONFIG_ENV_ADDR); + gd->env_valid = 1; +#else + env_relocate(); +#endif + +#ifdef CONFIG_SYS_I2C + i2c_init_all(); +#else + i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE); +#endif + + gd->ram_size = initdram(0); +#ifdef CONFIG_SPL_NAND_BOOT + puts("Tertiary program loader running in sram..."); +#else + puts("Second program loader running in sram...\n"); +#endif + +#ifdef CONFIG_SPL_MMC_BOOT + mmc_boot(); +#elif defined(CONFIG_SPL_SPI_BOOT) + spi_boot(); +#elif defined(CONFIG_SPL_NAND_BOOT) + nand_boot(); +#endif +} diff --git a/board/Arcturus/ucp1020/spl_minimal.c b/board/Arcturus/ucp1020/spl_minimal.c new file mode 100644 index 0000000000..5bdefb8a0d --- /dev/null +++ b/board/Arcturus/ucp1020/spl_minimal.c @@ -0,0 +1,67 @@ +/* + * Copyright 2013-2015 Arcturus Networks, Inc. + * http://www.arcturusnetworks.com/products/ucp1020/ + * based on board/freescale/p1_p2_rdb_pc/spl_minimal.c + * original copyright follows: + * Copyright 2011 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include +#include +#include +#include +#include +#include +#include +#include + +DECLARE_GLOBAL_DATA_PTR; + +void board_init_f(ulong bootflag) +{ + u32 plat_ratio; + ccsr_gur_t *gur = (void *)CONFIG_SYS_MPC85xx_GUTS_ADDR; + +#if defined(CONFIG_SYS_NAND_BR_PRELIM) && defined(CONFIG_SYS_NAND_OR_PRELIM) + set_lbc_br(0, CONFIG_SYS_NAND_BR_PRELIM); + set_lbc_or(0, CONFIG_SYS_NAND_OR_PRELIM); +#endif + + /* initialize selected port with appropriate baud rate */ + plat_ratio = in_be32(&gur->porpllsr) & MPC85xx_PORPLLSR_PLAT_RATIO; + plat_ratio >>= 1; + gd->bus_clk = CONFIG_SYS_CLK_FREQ * plat_ratio; + + NS16550_init((NS16550_t)CONFIG_SYS_NS16550_COM1, + gd->bus_clk / 16 / CONFIG_BAUDRATE); + + puts("\nNAND boot... "); + + /* copy code to RAM and jump to it - this should not return */ + /* NOTE - code has to be copied out of NAND buffer before + * other blocks can be read. + */ + relocate_code(CONFIG_SPL_RELOC_STACK, 0, CONFIG_SPL_RELOC_TEXT_BASE); +} + +void board_init_r(gd_t *gd, ulong dest_addr) +{ + puts("\nSecond program loader running in sram..."); + nand_boot(); +} + +void putc(char c) +{ + if (c == '\n') + NS16550_putc((NS16550_t)CONFIG_SYS_NS16550_COM1, '\r'); + + NS16550_putc((NS16550_t)CONFIG_SYS_NS16550_COM1, c); +} + +void puts(const char *str) +{ + while (*str) + putc(*str++); +} diff --git a/board/Arcturus/ucp1020/tlb.c b/board/Arcturus/ucp1020/tlb.c new file mode 100644 index 0000000000..fd7134f5cf --- /dev/null +++ b/board/Arcturus/ucp1020/tlb.c @@ -0,0 +1,101 @@ +/* + * Copyright 2013-2015 Arcturus Networks, Inc + * http://www.arcturusnetworks.com/products/ucp1020/ + * based on board/freescale/p1_p2_rdb_pc/tlb.c + * original copyright follows: + * Copyright 2010-2011 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include +#include + +struct fsl_e_tlb_entry tlb_table[] = { + /* TLB 0 - for temp stack in cache */ + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR, + CONFIG_SYS_INIT_RAM_ADDR_PHYS, + MAS3_SX | MAS3_SW | MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024, + CONFIG_SYS_INIT_RAM_ADDR_PHYS + 4 * 1024, + MAS3_SX | MAS3_SW | MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024, + CONFIG_SYS_INIT_RAM_ADDR_PHYS + 8 * 1024, + MAS3_SX | MAS3_SW | MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024, + CONFIG_SYS_INIT_RAM_ADDR_PHYS + 12 * 1024, + MAS3_SX | MAS3_SW | MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + + /* TLB 1 */ + /* *I*** - Covers boot page */ + SET_TLB_ENTRY(1, 0xfffff000, 0xfffff000, + MAS3_SX | MAS3_SW | MAS3_SR, MAS2_I, + 0, 0, BOOKE_PAGESZ_4K, 1), + + /* *I*G* - CCSRBAR */ + SET_TLB_ENTRY(1, CONFIG_SYS_CCSRBAR, CONFIG_SYS_CCSRBAR_PHYS, + MAS3_SX | MAS3_SW | MAS3_SR, MAS2_I | MAS2_G, + 0, 1, BOOKE_PAGESZ_1M, 1), + +#ifndef CONFIG_SPL_BUILD + /* W**G* - Flash/promjet, localbus */ + /* This will be changed to *I*G* after relocation to RAM. */ + SET_TLB_ENTRY(1, CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE_PHYS, + MAS3_SX | MAS3_SR, MAS2_W | MAS2_G, + 0, 2, BOOKE_PAGESZ_64M, 1), + +#ifdef CONFIG_PCI + /* *I*G* - PCI memory 1.5G */ + SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_MEM_VIRT, CONFIG_SYS_PCIE1_MEM_PHYS, + MAS3_SX | MAS3_SW | MAS3_SR, MAS2_I | MAS2_G, + 0, 3, BOOKE_PAGESZ_1G, 1), + + /* *I*G* - PCI I/O effective: 192K */ + SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_IO_VIRT, CONFIG_SYS_PCIE1_IO_PHYS, + MAS3_SX | MAS3_SW | MAS3_SR, MAS2_I | MAS2_G, + 0, 4, BOOKE_PAGESZ_256K, 1), +#endif + +#ifdef CONFIG_VSC7385_ENET + /* *I*G - VSC7385 Switch */ + SET_TLB_ENTRY(1, CONFIG_SYS_VSC7385_BASE, CONFIG_SYS_VSC7385_BASE_PHYS, + MAS3_SX | MAS3_SW | MAS3_SR, MAS2_I | MAS2_G, + 0, 5, BOOKE_PAGESZ_1M, 1), +#endif +#endif /* not SPL */ + +#ifdef CONFIG_SYS_NAND_BASE + /* *I*G - NAND */ + SET_TLB_ENTRY(1, CONFIG_SYS_NAND_BASE, CONFIG_SYS_NAND_BASE_PHYS, + MAS3_SX | MAS3_SW | MAS3_SR, MAS2_I | MAS2_G, + 0, 7, BOOKE_PAGESZ_1M, 1), +#endif + +#if defined(CONFIG_SYS_RAMBOOT) || \ + (defined(CONFIG_SPL) && !defined(CONFIG_SPL_COMMON_INIT_DDR)) + /* *I*G - eSDHC/eSPI/NAND boot */ + SET_TLB_ENTRY(1, CONFIG_SYS_DDR_SDRAM_BASE, CONFIG_SYS_DDR_SDRAM_BASE, + MAS3_SX | MAS3_SW | MAS3_SR, 0, + 0, 8, BOOKE_PAGESZ_1G, 1), + +#endif /* RAMBOOT/SPL */ + +#ifdef CONFIG_SYS_INIT_L2_ADDR + /* *I*G - L2SRAM */ + SET_TLB_ENTRY(1, CONFIG_SYS_INIT_L2_ADDR, CONFIG_SYS_INIT_L2_ADDR_PHYS, + MAS3_SX | MAS3_SW | MAS3_SR, MAS2_G, + 0, 11, BOOKE_PAGESZ_256K, 1), +#if CONFIG_SYS_L2_SIZE >= (256 << 10) + SET_TLB_ENTRY(1, CONFIG_SYS_INIT_L2_ADDR + 0x40000, + CONFIG_SYS_INIT_L2_ADDR_PHYS + 0x40000, + MAS3_SX | MAS3_SW | MAS3_SR, MAS2_I | MAS2_G, + 0, 12, BOOKE_PAGESZ_256K, 1) +#endif +#endif +}; + +int num_tlb_entries = ARRAY_SIZE(tlb_table); diff --git a/board/Arcturus/ucp1020/ucp1020.c b/board/Arcturus/ucp1020/ucp1020.c new file mode 100644 index 0000000000..0fc2bac55d --- /dev/null +++ b/board/Arcturus/ucp1020/ucp1020.c @@ -0,0 +1,363 @@ +/* + * Copyright 2013-2015 Arcturus Networks, Inc. + * http://www.arcturusnetworks.com/products/ucp1020/ + * by Oleksandr G Zhadan et al. + * based on board/freescale/p1_p2_rdb_pc/spl.c + * original copyright follows: + * Copyright 2013 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include "ucp1020.h" + +void spi_set_speed(struct spi_slave *slave, uint hz) +{ + /* TO DO: It's actially have to be in spi/ */ +} + +/* + * To be compatible with cmd_gpio + */ +int name_to_gpio(const char *name) +{ + int gpio = 31 - simple_strtoul(name, NULL, 10); + + if (gpio < 16) + gpio = -1; + + return gpio; +} + +void board_gpio_init(void) +{ + int i; + char envname[8], *val; + + for (i = 0; i < GPIO_MAX_NUM; i++) { + sprintf(envname, "GPIO%d", i); + val = getenv(envname); + if (val) { + char direction = toupper(val[0]); + char level = toupper(val[1]); + + if (direction == 'I') { + gpio_direction_input(i); + } else { + if (direction == 'O') { + if (level == '1') + gpio_direction_output(i, 1); + else + gpio_direction_output(i, 0); + } + } + } + } + + val = getenv("PCIE_OFF"); + if (val) { + gpio_direction_input(GPIO_PCIE1_EN); + gpio_direction_input(GPIO_PCIE2_EN); + } else { + gpio_direction_output(GPIO_PCIE1_EN, 1); + gpio_direction_output(GPIO_PCIE2_EN, 1); + } + + val = getenv("SDHC_CDWP_OFF"); + if (!val) { + ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); + + setbits_be32(&gur->pmuxcr, + (MPC85xx_PMUXCR_SDHC_CD | MPC85xx_PMUXCR_SDHC_WP)); + } +} + +int board_early_init_f(void) +{ + return 0; /* Just in case. Could be disable in config file */ +} + +int checkboard(void) +{ + printf("Board: %s\n", CONFIG_BOARDNAME_LOCAL); + board_gpio_init(); + printf("SD/MMC: 4-bit Mode\n"); + + return 0; +} + +#ifdef CONFIG_PCI +void pci_init_board(void) +{ + fsl_pcie_init_board(0); +} +#endif + +int board_early_init_r(void) +{ + const unsigned int flashbase = CONFIG_SYS_FLASH_BASE; + const u8 flash_esel = find_tlb_idx((void *)flashbase, 1); + + /* + * Remap Boot flash region to caching-inhibited + * so that flash can be erased properly. + */ + + /* Flush d-cache and invalidate i-cache of any FLASH data */ + flush_dcache(); + invalidate_icache(); + + /* invalidate existing TLB entry for flash */ + disable_tlb(flash_esel); + + set_tlb(1, flashbase, CONFIG_SYS_FLASH_BASE_PHYS, /* tlb, epn, rpn */ + MAS3_SX | MAS3_SW | MAS3_SR, MAS2_I | MAS2_G, /* perms, wimge */ + 0, flash_esel, BOOKE_PAGESZ_64M, 1);/* ts, esel, tsize, iprot */ + + return 0; +} + +int board_phy_config(struct phy_device *phydev) +{ +#if defined(CONFIG_PHY_MICREL_KSZ9021) + int regval; + static int cnt; + + if (cnt++ == 0) + printf("PHYs address ["); + + if (phydev->addr == TSEC1_PHY_ADDR || phydev->addr == TSEC3_PHY_ADDR) { + regval = + ksz9021_phy_extended_read(phydev, + MII_KSZ9021_EXT_STRAP_STATUS); + /* + * min rx data delay + */ + ksz9021_phy_extended_write(phydev, + MII_KSZ9021_EXT_RGMII_RX_DATA_SKEW, + 0x6666); + /* + * max rx/tx clock delay, min rx/tx control + */ + ksz9021_phy_extended_write(phydev, + MII_KSZ9021_EXT_RGMII_CLOCK_SKEW, + 0xf6f6); + printf("0x%x", (regval & 0x1f)); + } else { + printf("0x%x", (TSEC2_PHY_ADDR & 0x1f)); + } + if (cnt == 3) + printf("] "); + else + printf(","); +#endif + +#if defined(CONFIG_PHY_MICREL_KSZ9031_DEBUG) + regval = ksz9031_phy_extended_read(phydev, 2, 0x01, 0x4000); + if (regval >= 0) + printf(" (ADDR 0x%x) ", regval & 0x1f); +#endif + + return 0; +} + +int last_stage_init(void) +{ + static char newkernelargs[256]; + static u8 id1[16]; + static u8 id2; + struct mmc *mmc; + char *sval, *kval; + + if (i2c_read(CONFIG_SYS_I2C_IDT6V49205B, 7, 1, &id1[0], 2) < 0) { + printf("Error reading i2c IDT6V49205B information!\n"); + } else { + printf("IDT6V49205B(0x%02x): ready\n", id1[1]); + i2c_read(CONFIG_SYS_I2C_IDT6V49205B, 4, 1, &id1[0], 2); + if (!(id1[1] & 0x02)) { + id1[1] |= 0x02; + i2c_write(CONFIG_SYS_I2C_IDT6V49205B, 4, 1, &id1[0], 2); + asm("nop; nop"); + } + } + + if (i2c_read(CONFIG_SYS_I2C_NCT72_ADDR, 0xFE, 1, &id2, 1) < 0) + printf("Error reading i2c NCT72 information!\n"); + else + printf("NCT72(0x%x): ready\n", id2); + + kval = getenv("kernelargs"); + + mmc = find_mmc_device(0); + if (mmc) + if (!mmc_init(mmc)) { + printf("MMC/SD card detected\n"); + if (kval) { + int n = strlen(defkargs); + char *tmp = strstr(kval, defkargs); + + *tmp = 0; + strcpy(newkernelargs, kval); + strcat(newkernelargs, " "); + strcat(newkernelargs, mmckargs); + strcat(newkernelargs, " "); + strcat(newkernelargs, &tmp[n]); + setenv("kernelargs", newkernelargs); + } else { + setenv("kernelargs", mmckargs); + } + } + get_arc_info(); + + if (kval) { + sval = getenv("SERIAL"); + if (sval) { + strcpy(newkernelargs, "SN="); + strcat(newkernelargs, sval); + strcat(newkernelargs, " "); + strcat(newkernelargs, kval); + setenv("kernelargs", newkernelargs); + } + } else { + printf("Error reading kernelargs env variable!\n"); + } + + return 0; +} + +int board_eth_init(bd_t *bis) +{ + struct fsl_pq_mdio_info mdio_info; + struct tsec_info_struct tsec_info[4]; +#ifdef CONFIG_TSEC2 + ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); +#endif + int num = 0; + +#ifdef CONFIG_TSEC1 + SET_STD_TSEC_INFO(tsec_info[num], 1); + num++; +#endif +#ifdef CONFIG_TSEC2 + SET_STD_TSEC_INFO(tsec_info[num], 2); + if (is_serdes_configured(SGMII_TSEC2)) { + if (!(in_be32(&gur->pordevsr) & MPC85xx_PORDEVSR_SGMII2_DIS)) { + puts("eTSEC2 is in sgmii mode.\n"); + tsec_info[num].flags |= TSEC_SGMII; + tsec_info[num].phyaddr = TSEC2_PHY_ADDR_SGMII; + } + } + num++; +#endif +#ifdef CONFIG_TSEC3 + SET_STD_TSEC_INFO(tsec_info[num], 3); + num++; +#endif + + if (!num) { + printf("No TSECs initialized\n"); + return 0; + } + + mdio_info.regs = (struct tsec_mii_mng *)CONFIG_SYS_MDIO_BASE_ADDR; + mdio_info.name = DEFAULT_MII_NAME; + + fsl_pq_mdio_init(bis, &mdio_info); + + tsec_eth_init(bis, tsec_info, num); + + return pci_eth_init(bis); +} + +#ifdef CONFIG_OF_BOARD_SETUP +int ft_board_setup(void *blob, bd_t *bd) +{ + phys_addr_t base; + phys_size_t size; + const char *soc_usb_compat = "fsl-usb2-dr"; + int err, usb1_off, usb2_off; + + ft_cpu_setup(blob, bd); + + base = getenv_bootm_low(); + size = getenv_bootm_size(); + + fdt_fixup_memory(blob, (u64)base, (u64)size); + + FT_FSL_PCI_SETUP; + +#if defined(CONFIG_HAS_FSL_DR_USB) + fdt_fixup_dr_usb(blob, bd); +#endif + +#if defined(CONFIG_SDCARD) || defined(CONFIG_SPIFLASH) + /* Delete eLBC node as it is muxed with USB2 controller */ + if (hwconfig("usb2")) { + const char *soc_elbc_compat = "fsl,p1020-elbc"; + int off = fdt_node_offset_by_compatible(blob, -1, + soc_elbc_compat); + if (off < 0) { + printf + ("WARNING: could not find compatible node %s: %s\n", + soc_elbc_compat, fdt_strerror(off)); + return off; + } + err = fdt_del_node(blob, off); + if (err < 0) { + printf("WARNING: could not remove %s: %s\n", + soc_elbc_compat, fdt_strerror(err)); + } + return err; + } +#endif + +/* Delete USB2 node as it is muxed with eLBC */ + usb1_off = fdt_node_offset_by_compatible(blob, -1, soc_usb_compat); + if (usb1_off < 0) { + printf("WARNING: could not find compatible node %s: %s.\n", + soc_usb_compat, fdt_strerror(usb1_off)); + return usb1_off; + } + usb2_off = + fdt_node_offset_by_compatible(blob, usb1_off, soc_usb_compat); + if (usb2_off < 0) { + printf("WARNING: could not find compatible node %s: %s.\n", + soc_usb_compat, fdt_strerror(usb2_off)); + return usb2_off; + } + err = fdt_del_node(blob, usb2_off); + if (err < 0) { + printf("WARNING: could not remove %s: %s.\n", + soc_usb_compat, fdt_strerror(err)); + } + return 0; +} +#endif diff --git a/board/Arcturus/ucp1020/ucp1020.h b/board/Arcturus/ucp1020/ucp1020.h new file mode 100644 index 0000000000..243459c446 --- /dev/null +++ b/board/Arcturus/ucp1020/ucp1020.h @@ -0,0 +1,44 @@ +/* + * Copyright 2013-2015 Arcturus Networks, Inc. + * http://www.arcturusnetworks.com/products/ucp1020/ + * by Oleksandr G Zhadan et al. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef __UCP1020_H__ +#define __UCP1020_H__ + +#define GPIO0 31 +#define GPIO1 30 +#define GPIO2 29 +#define GPIO3 28 +#define GPIO4 27 +#define GPIO5 26 +#define GPIO6 25 +#define GPIO7 24 +#define GPIO8 23 +#define GPIO9 22 +#define GPIO10 21 +#define GPIO11 20 +#define GPIO12 19 +#define GPIO13 18 +#define GPIO14 17 +#define GPIO15 16 +#define GPIO_MAX_NUM 16 + +#define GPIO_SDHC_CD GPIO8 +#define GPIO_SDHC_WP GPIO9 +#define GPIO_USB_PCTL0 GPIO10 +#define GPIO_PCIE1_EN GPIO11 +#define GPIO_PCIE2_EN GPIO10 +#define GPIO_USB_PCTL1 GPIO11 + +#define GPIO_WD GPIO15 + +static char *defkargs = "root=/dev/mtdblock1 rootfstype=cramfs ro"; +static char *mmckargs = "root=/dev/mmcblk0p1 rootwait rw"; + +int get_arc_info(void); + +#endif diff --git a/configs/UCP1020_SPIFLASH_defconfig b/configs/UCP1020_SPIFLASH_defconfig new file mode 100644 index 0000000000..2ffb8da3a5 --- /dev/null +++ b/configs/UCP1020_SPIFLASH_defconfig @@ -0,0 +1,6 @@ +CONFIG_PPC=y +CONFIG_MPC85xx=y +CONFIG_TARGET_UCP1020=y +CONFIG_TARGET_UCP1020_SPIFLASH=y +CONFIG_SPI_FLASH=y +CONFIG_UCP1020=y diff --git a/configs/UCP1020_defconfig b/configs/UCP1020_defconfig new file mode 100644 index 0000000000..61de360fe3 --- /dev/null +++ b/configs/UCP1020_defconfig @@ -0,0 +1,5 @@ +CONFIG_PPC=y +CONFIG_MPC85xx=y +CONFIG_TARGET_UCP1020=y +CONFIG_SPI_FLASH=y +CONFIG_UCP1020=y diff --git a/include/configs/UCP1020.h b/include/configs/UCP1020.h new file mode 100644 index 0000000000..57e0c6c747 --- /dev/null +++ b/include/configs/UCP1020.h @@ -0,0 +1,1027 @@ +/* + * Copyright 2013-2015 Arcturus Networks, Inc. + * http://www.arcturusnetworks.com/products/ucp1020/ + * based on include/configs/p1_p2_rdb_pc.h + * original copyright follows: + * Copyright 2009-2011 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +/* + * QorIQ uCP1020-xx boards configuration file + */ +#ifndef __CONFIG_H +#define __CONFIG_H + +#define CONFIG_SYS_GENERIC_BOARD +#define CONFIG_DISPLAY_BOARDINFO + +#define CONFIG_FSL_ELBC +#define CONFIG_PCI +#define CONFIG_PCIE1 /* PCIE controller 1 (slot 1) */ +#define CONFIG_PCIE2 /* PCIE controller 2 (slot 2) */ +#define CONFIG_FSL_PCI_INIT /* Use common FSL init code */ +#define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */ +#define CONFIG_FSL_PCIE_RESET /* need PCIe reset errata */ +#define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */ + +#if defined(CONFIG_TARTGET_UCP1020T1) + +#define CONFIG_UCP1020_REV_1_3 + +#define CONFIG_BOARDNAME "uCP1020-64EE512-0U1-XR-T1" +#define CONFIG_P1020 + +#define CONFIG_TSEC_ENET +#define CONFIG_TSEC1 +#define CONFIG_TSEC3 +#define CONFIG_HAS_ETH0 +#define CONFIG_HAS_ETH1 +#define CONFIG_ETHADDR 00:19:D3:FF:FF:FF +#define CONFIG_ETH1ADDR 00:19:D3:FF:FF:FE +#define CONFIG_ETH2ADDR 00:19:D3:FF:FF:FD +#define CONFIG_IPADDR 10.80.41.229 +#define CONFIG_SERVERIP 10.80.41.227 +#define CONFIG_NETMASK 255.255.252.0 +#define CONFIG_ETHPRIME "eTSEC3" + +#ifndef CONFIG_SPI_FLASH +#define CONFIG_SPI_FLASH y +#endif +#define CONFIG_SYS_REDUNDAND_ENVIRONMENT + +#define CONFIG_MMC +#define CONFIG_SYS_L2_SIZE (256 << 10) + +#define CONFIG_LAST_STAGE_INIT + +#if !defined(CONFIG_DONGLE) +#define CONFIG_SILENT_CONSOLE +#endif + +#endif + +#if defined(CONFIG_TARGET_UCP1020) + +#define CONFIG_UCP1020 +#define CONFIG_UCP1020_REV_1_3 + +#define CONFIG_BOARDNAME_LOCAL "uCP1020-64EEE512-OU1-XR" +#define CONFIG_P1020 + +#define CONFIG_TSEC_ENET +#define CONFIG_TSEC1 +#define CONFIG_TSEC2 +#define CONFIG_TSEC3 +#define CONFIG_HAS_ETH0 +#define CONFIG_HAS_ETH1 +#define CONFIG_HAS_ETH2 +#define CONFIG_ETHADDR 00:06:3B:FF:FF:FF +#define CONFIG_ETH1ADDR 00:06:3B:FF:FF:FE +#define CONFIG_ETH2ADDR 00:06:3B:FF:FF:FD +#define CONFIG_IPADDR 192.168.1.81 +#define CONFIG_IPADDR1 192.168.1.82 +#define CONFIG_IPADDR2 192.168.1.83 +#define CONFIG_SERVERIP 192.168.1.80 +#define CONFIG_GATEWAYIP 102.168.1.1 +#define CONFIG_NETMASK 255.255.255.0 +#define CONFIG_ETHPRIME "eTSEC1" + +#ifndef CONFIG_SPI_FLASH +#define CONFIG_SPI_FLASH y +#endif +#define CONFIG_SYS_REDUNDAND_ENVIRONMENT + +#define CONFIG_MMC +#define CONFIG_SYS_L2_SIZE (256 << 10) + +#define CONFIG_LAST_STAGE_INIT + +#endif + +#ifdef CONFIG_SDCARD +#define CONFIG_RAMBOOT_SDCARD +#define CONFIG_SYS_RAMBOOT +#define CONFIG_SYS_EXTRA_ENV_RELOC +#define CONFIG_SYS_TEXT_BASE 0x11000000 +#define CONFIG_RESET_VECTOR_ADDRESS 0x1107fffc +#endif + +#ifdef CONFIG_SPIFLASH +#define CONFIG_RAMBOOT_SPIFLASH +#define CONFIG_SYS_RAMBOOT +#define CONFIG_SYS_EXTRA_ENV_RELOC +#define CONFIG_SYS_TEXT_BASE 0x11000000 +#define CONFIG_RESET_VECTOR_ADDRESS 0x1107fffc +#endif + +#ifndef CONFIG_SYS_TEXT_BASE +#define CONFIG_SYS_TEXT_BASE 0xeff80000 +#endif +#define CONFIG_SYS_TEXT_BASE_NOR 0xeff80000 + +#ifndef CONFIG_RESET_VECTOR_ADDRESS +#define CONFIG_RESET_VECTOR_ADDRESS 0xeffffffc +#endif + +#ifndef CONFIG_SYS_MONITOR_BASE +#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ +#endif + +/* High Level Configuration Options */ +#define CONFIG_BOOKE +#define CONFIG_E500 +/* #define CONFIG_MPC85xx */ + +#define CONFIG_MP + +#define CONFIG_FSL_LAW + +#define CONFIG_ENV_OVERWRITE + +#define CONFIG_CMD_SATA +#define CONFIG_SATA_SIL +#define CONFIG_SYS_SATA_MAX_DEVICE 2 +#define CONFIG_LIBATA +#define CONFIG_LBA48 + +#define CONFIG_SYS_CLK_FREQ 66666666 +#define CONFIG_DDR_CLK_FREQ 66666666 + +#define CONFIG_HWCONFIG + +#define CONFIG_DTT_ADM1021 1 /* ADM1021 temp sensor support */ +#define CONFIG_SYS_DTT_BUS_NUM 1 /* The I2C bus for DTT */ +#define CONFIG_DTT_SENSORS { 0, 1 } /* Sensor index */ +/* + * ADM1021/NCT72 temp sensor configuration (see dtt/adm1021.c for details). + * there will be one entry in this array for each two (dummy) sensors in + * CONFIG_DTT_SENSORS. + * + * For uCP1020 module: + * - only one ADM1021/NCT72 + * - i2c addr 0x41 + * - conversion rate 0x02 = 0.25 conversions/second + * - ALERT output disabled + * - local temp sensor enabled, min set to 0 deg, max set to 85 deg + * - remote temp sensor enabled, min set to 0 deg, max set to 85 deg + */ +#define CONFIG_SYS_DTT_ADM1021 { { CONFIG_SYS_I2C_NCT72_ADDR, \ + 0x02, 0, 1, 0, 85, 1, 0, 85} } + +#define CONFIG_CMD_DTT + +/* + * These can be toggled for performance analysis, otherwise use default. + */ +#define CONFIG_L2_CACHE +#define CONFIG_BTB + +#define CONFIG_BOARD_EARLY_INIT_F /* Call board_pre_init */ + +#define CONFIG_ENABLE_36BIT_PHYS + +#define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */ +#define CONFIG_SYS_MEMTEST_END 0x1fffffff +#define CONFIG_PANIC_HANG /* do not reset board on panic */ + +#define CONFIG_SYS_CCSRBAR 0xffe00000 +#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR + +/* IN case of NAND bootloader relocate CCSRBAR in RAMboot code not in the 4k + SPL code*/ +#ifdef CONFIG_SPL_BUILD +#define CONFIG_SYS_CCSR_DO_NOT_RELOCATE +#endif + +/* DDR Setup */ +#define CONFIG_DDR_ECC_ENABLE +#define CONFIG_SYS_FSL_DDR3 +#ifndef CONFIG_DDR_ECC_ENABLE +#define CONFIG_SYS_DDR_RAW_TIMING +#define CONFIG_DDR_SPD +#endif +#define CONFIG_SYS_SPD_BUS_NUM 1 +#undef CONFIG_FSL_DDR_INTERACTIVE + +#define CONFIG_SYS_SDRAM_SIZE_LAW LAW_SIZE_512M +#define CONFIG_CHIP_SELECTS_PER_CTRL 1 +#define CONFIG_SYS_SDRAM_SIZE (1u << (CONFIG_SYS_SDRAM_SIZE_LAW - 19)) +#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 +#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE + +#define CONFIG_NUM_DDR_CONTROLLERS 1 +#define CONFIG_DIMM_SLOTS_PER_CTLR 1 + +/* Default settings for DDR3 */ +#define CONFIG_SYS_DDR_CS0_BNDS 0x0000003f +#define CONFIG_SYS_DDR_CS0_CONFIG 0x80014302 +#define CONFIG_SYS_DDR_CS0_CONFIG_2 0x00000000 +#define CONFIG_SYS_DDR_CS1_BNDS 0x0040007f +#define CONFIG_SYS_DDR_CS1_CONFIG 0x80014302 +#define CONFIG_SYS_DDR_CS1_CONFIG_2 0x00000000 + +#define CONFIG_SYS_DDR_DATA_INIT 0xdeadbeef +#define CONFIG_SYS_DDR_INIT_ADDR 0x00000000 +#define CONFIG_SYS_DDR_INIT_EXT_ADDR 0x00000000 +#define CONFIG_SYS_DDR_MODE_CONTROL 0x00000000 + +#define CONFIG_SYS_DDR_ZQ_CONTROL 0x89080600 +#define CONFIG_SYS_DDR_WRLVL_CONTROL 0x8655A608 +#define CONFIG_SYS_DDR_SR_CNTR 0x00000000 +#define CONFIG_SYS_DDR_RCW_1 0x00000000 +#define CONFIG_SYS_DDR_RCW_2 0x00000000 +#ifdef CONFIG_DDR_ECC_ENABLE +#define CONFIG_SYS_DDR_CONTROL 0xE70C0000 /* Type = DDR3 & ECC */ +#else +#define CONFIG_SYS_DDR_CONTROL 0xC70C0000 /* Type = DDR3 */ +#endif +#define CONFIG_SYS_DDR_CONTROL_2 0x04401050 +#define CONFIG_SYS_DDR_TIMING_4 0x00220001 +#define CONFIG_SYS_DDR_TIMING_5 0x03402400 + +#define CONFIG_SYS_DDR_TIMING_3 0x00020000 +#define CONFIG_SYS_DDR_TIMING_0 0x00330004 +#define CONFIG_SYS_DDR_TIMING_1 0x6f6B4846 +#define CONFIG_SYS_DDR_TIMING_2 0x0FA8C8CF +#define CONFIG_SYS_DDR_CLK_CTRL 0x03000000 +#define CONFIG_SYS_DDR_MODE_1 0x40461520 +#define CONFIG_SYS_DDR_MODE_2 0x8000c000 +#define CONFIG_SYS_DDR_INTERVAL 0x0C300000 + +#undef CONFIG_CLOCKS_IN_MHZ + +/* + * Memory map + * + * 0x0000_0000 0x7fff_ffff DDR Up to 2GB cacheable + * 0x8000_0000 0xdfff_ffff PCI Express Mem 1G non-cacheable(PCIe * 2) + * 0xec00_0000 0xefff_ffff NOR flash Up to 64M non-cacheable CS0/1 + * 0xf8f8_0000 0xf8ff_ffff L2 SRAM Up to 256K cacheable + * (early boot only) + * 0xffc0_0000 0xffc3_ffff PCI IO range 256k non-cacheable + * 0xffd0_0000 0xffd0_3fff L1 for stack 16K cacheable + * 0xffe0_0000 0xffef_ffff CCSR 1M non-cacheable + */ + +/* + * Local Bus Definitions + */ +#define CONFIG_SYS_MAX_FLASH_SECT 512 /* 64M */ +#define CONFIG_SYS_FLASH_BASE 0xec000000 + +#define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE + +#define CONFIG_FLASH_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) \ + | BR_PS_16 | BR_V) + +#define CONFIG_FLASH_OR_PRELIM 0xfc000ff7 + +#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS} +#define CONFIG_SYS_FLASH_QUIET_TEST +#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */ + +#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ + +#undef CONFIG_SYS_FLASH_CHECKSUM +#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ +#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ + +#define CONFIG_FLASH_CFI_DRIVER +#define CONFIG_SYS_FLASH_CFI +#define CONFIG_SYS_FLASH_EMPTY_INFO +#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE + +#define CONFIG_BOARD_EARLY_INIT_R /* call board_early_init_r function */ + +#define CONFIG_SYS_INIT_RAM_LOCK +#define CONFIG_SYS_INIT_RAM_ADDR 0xffd00000 /* stack in RAM */ +/* Initial L1 address */ +#define CONFIG_SYS_INIT_RAM_ADDR_PHYS CONFIG_SYS_INIT_RAM_ADDR +#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0 +#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR_PHYS +/* Size of used area in RAM */ +#define CONFIG_SYS_INIT_RAM_SIZE 0x00004000 + +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \ + GENERATED_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET + +#define CONFIG_SYS_MONITOR_LEN (256 * 1024)/* Reserve 256 kB for Mon */ +#define CONFIG_SYS_MALLOC_LEN (1024 * 1024)/* Reserved for malloc */ + +#define CONFIG_SYS_PMC_BASE 0xff980000 +#define CONFIG_SYS_PMC_BASE_PHYS CONFIG_SYS_PMC_BASE +#define CONFIG_PMC_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_PMC_BASE_PHYS) | \ + BR_PS_8 | BR_V) +#define CONFIG_PMC_OR_PRELIM (OR_AM_64KB | OR_GPCM_CSNT | OR_GPCM_XACS | \ + OR_GPCM_SCY | OR_GPCM_TRLX | OR_GPCM_EHTR | \ + OR_GPCM_EAD) + +#define CONFIG_SYS_BR0_PRELIM CONFIG_FLASH_BR_PRELIM /* NOR Base Address */ +#define CONFIG_SYS_OR0_PRELIM CONFIG_FLASH_OR_PRELIM /* NOR Options */ +#ifdef CONFIG_NAND_FSL_ELBC +#define CONFIG_SYS_BR1_PRELIM CONFIG_SYS_NAND_BR_PRELIM /* NAND Base Addr */ +#define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */ +#endif + +/* Serial Port - controlled on board with jumper J8 + * open - index 2 + * shorted - index 1 + */ +#define CONFIG_CONS_INDEX 1 +#undef CONFIG_SERIAL_SOFTWARE_FIFO +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 +#define CONFIG_SYS_NS16550_CLK get_bus_freq(0) +#if defined(CONFIG_SPL_BUILD) && defined(CONFIG_SPL_INIT_MINIMAL) +#define CONFIG_NS16550_MIN_FUNCTIONS +#endif + +#define CONFIG_SYS_BAUDRATE_TABLE \ + {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} + +#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR + 0x4500) +#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR + 0x4600) + +/* Use the HUSH parser */ +#define CONFIG_SYS_HUSH_PARSER + +/* + * Pass open firmware flat tree + */ +#define CONFIG_OF_LIBFDT +#define CONFIG_OF_BOARD_SETUP +#define CONFIG_OF_STDOUT_VIA_ALIAS + +/* new uImage format support */ +#define CONFIG_FIT +#define CONFIG_FIT_VERBOSE /* enable fit_format_{error,warning}() */ + +/* I2C */ +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 400000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 +#define CONFIG_SYS_FSL_I2C2_SPEED 400000 +#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 +#define CONFIG_SYS_I2C_NOPROBES { {0, 0x29} } +#define CONFIG_SYS_SPD_BUS_NUM 1 /* For rom_loc and flash bank */ + +#define CONFIG_RTC_DS1337 +#define CONFIG_SYS_RTC_DS1337_NOOSC +#define CONFIG_SYS_I2C_RTC_ADDR 0x68 +#define CONFIG_SYS_I2C_PCA9557_ADDR 0x18 +#define CONFIG_SYS_I2C_NCT72_ADDR 0x4C +#define CONFIG_SYS_I2C_IDT6V49205B 0x69 + +/* + * eSPI - Enhanced SPI + */ +#define CONFIG_HARD_SPI +#define CONFIG_FSL_ESPI + +#define CONFIG_SPI_FLASH_SST 1 +#define CONFIG_SPI_FLASH_STMICRO 1 +#define CONFIG_SPI_FLASH_WINBOND 1 +#define CONFIG_CMD_SF 1 +#define CONFIG_CMD_SPI 1 +#define CONFIG_SF_DEFAULT_SPEED 10000000 +#define CONFIG_SF_DEFAULT_MODE SPI_MODE_0 + +#if defined(CONFIG_PCI) +/* + * General PCI + * Memory space is mapped 1-1, but I/O space must start from 0. + */ + +/* controller 2, direct to uli, tgtid 2, Base address 9000 */ +#define CONFIG_SYS_PCIE2_NAME "PCIe SLOT CON9" +#define CONFIG_SYS_PCIE2_MEM_VIRT 0xa0000000 +#define CONFIG_SYS_PCIE2_MEM_BUS 0xa0000000 +#define CONFIG_SYS_PCIE2_MEM_PHYS 0xa0000000 +#define CONFIG_SYS_PCIE2_MEM_SIZE 0x20000000 /* 512M */ +#define CONFIG_SYS_PCIE2_IO_VIRT 0xffc10000 +#define CONFIG_SYS_PCIE2_IO_BUS 0x00000000 +#define CONFIG_SYS_PCIE2_IO_PHYS 0xffc10000 +#define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */ + +/* controller 1, Slot 2, tgtid 1, Base address a000 */ +#define CONFIG_SYS_PCIE1_NAME "PCIe SLOT CON10" +#define CONFIG_SYS_PCIE1_MEM_VIRT 0x80000000 +#define CONFIG_SYS_PCIE1_MEM_BUS 0x80000000 +#define CONFIG_SYS_PCIE1_MEM_PHYS 0x80000000 +#define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */ +#define CONFIG_SYS_PCIE1_IO_VIRT 0xffc00000 +#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 +#define CONFIG_SYS_PCIE1_IO_PHYS 0xffc00000 +#define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */ + +#define CONFIG_PCI_PNP /* do pci plug-and-play */ +#define CONFIG_E1000 /* Defind e1000 pci Ethernet card*/ +#define CONFIG_CMD_PCI +#define CONFIG_CMD_NET + +#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ +#define CONFIG_DOS_PARTITION +#endif /* CONFIG_PCI */ + +/* + * Environment + */ +#ifdef CONFIG_ENV_FIT_UCBOOT + +#define CONFIG_ENV_IS_IN_FLASH +#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x20000) +#define CONFIG_ENV_SIZE 0x20000 +#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */ + +#else + +#define CONFIG_ENV_SPI_BUS 0 +#define CONFIG_ENV_SPI_CS 0 +#define CONFIG_ENV_SPI_MAX_HZ 10000000 +#define CONFIG_ENV_SPI_MODE 0 + +#ifdef CONFIG_RAMBOOT_SPIFLASH + +#define CONFIG_ENV_IS_IN_SPI_FLASH +#define CONFIG_ENV_SIZE 0x3000 /* 12KB */ +#define CONFIG_ENV_OFFSET 0x2000 /* 8KB */ +#define CONFIG_ENV_SECT_SIZE 0x1000 + +#if defined(CONFIG_SYS_REDUNDAND_ENVIRONMENT) +/* Address and size of Redundant Environment Sector */ +#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE) +#define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE +#endif + +#elif defined(CONFIG_RAMBOOT_SDCARD) +#define CONFIG_ENV_IS_IN_MMC +#define CONFIG_FSL_FIXED_MMC_LOCATION +#define CONFIG_ENV_SIZE 0x2000 +#define CONFIG_SYS_MMC_ENV_DEV 0 + +#elif defined(CONFIG_SYS_RAMBOOT) +#define CONFIG_ENV_IS_NOWHERE /* Store ENV in memory only */ +#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000) +#define CONFIG_ENV_SIZE 0x2000 + +#else +#define CONFIG_ENV_IS_IN_FLASH +#define CONFIG_ENV_BASE (CONFIG_SYS_FLASH_BASE) +#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */ +#define CONFIG_ENV_SIZE CONFIG_ENV_SECT_SIZE +#define CONFIG_ENV_ADDR (CONFIG_ENV_BASE + 0xC0000) +#if defined(CONFIG_SYS_REDUNDAND_ENVIRONMENT) +/* Address and size of Redundant Environment Sector */ +#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SIZE) +#define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE +#endif + +#endif + +#endif /* CONFIG_ENV_FIT_UCBOOT */ + +#define CONFIG_LOADS_ECHO /* echo on for serial download */ +#define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */ + +/* + * Command line configuration. + */ +#include + +#define CONFIG_CMD_IRQ +#define CONFIG_CMD_PING +#define CONFIG_CMD_I2C +#define CONFIG_CMD_MII +#define CONFIG_CMD_DATE +#define CONFIG_CMD_ELF +#define CONFIG_CMD_I2C +#define CONFIG_CMD_IRQ +#define CONFIG_CMD_MII +#define CONFIG_CMD_PING +#define CONFIG_CMD_SETEXPR +#define CONFIG_CMD_REGINFO +#define CONFIG_CMD_ERRATA +#define CONFIG_CMD_CRAMFS +#define CONFIG_CRAMFS_CMDLINE + +/* + * USB + */ +#define CONFIG_HAS_FSL_DR_USB + +#if defined(CONFIG_HAS_FSL_DR_USB) +#define CONFIG_USB_EHCI + +#define CONFIG_USB_MAX_CONTROLLER_COUNT 1 + +#ifdef CONFIG_USB_EHCI +#define CONFIG_CMD_USB +#define CONFIG_EHCI_HCD_INIT_AFTER_RESET +#define CONFIG_USB_EHCI_FSL +#define CONFIG_USB_STORAGE +#endif +#endif + +#undef CONFIG_WATCHDOG /* watchdog disabled */ + +#ifdef CONFIG_MMC +#define CONFIG_FSL_ESDHC +#define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR +#define CONFIG_CMD_MMC +#define CONFIG_MMC_SPI +#define CONFIG_CMD_MMC_SPI +#define CONFIG_GENERIC_MMC +#endif + +#if defined(CONFIG_MMC) || defined(CONFIG_USB_EHCI) || defined(CONFIG_FSL_SATA) +#define CONFIG_CMD_EXT2 +#define CONFIG_CMD_FAT +#define CONFIG_DOS_PARTITION +#endif + +/* Misc Extra Settings */ +#define CONFIG_CMD_GPIO 1 +#undef CONFIG_WATCHDOG /* watchdog disabled */ + +/* + * Miscellaneous configurable options + */ +#define CONFIG_SYS_LONGHELP /* undef to save memory */ +#define CONFIG_CMDLINE_EDITING /* Command-line editing */ +#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ +#define CONFIG_SYS_PROMPT "B$ " /* Monitor Command Prompt */ +#if defined(CONFIG_CMD_KGDB) +#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ +#endif +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) + /* Print Buffer Size */ +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE/* Boot Argument Buffer Size */ +#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms tick */ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 64 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial Memory for Linux*/ +#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ + +#if defined(CONFIG_CMD_KGDB) +#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ +#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ +#endif + +/* + * Environment Configuration + */ + +#if defined(CONFIG_TSEC_ENET) + +#if defined(CONFIG_UCP1020_REV_1_2) +#define CONFIG_PHY_MICREL_KSZ9021 +#elif defined(CONFIG_UCP1020_REV_1_3) +#define CONFIG_PHY_MICREL_KSZ9031 +#else +#error "UCP1020 module revision is not defined !!!" +#endif + +#define CONFIG_CMD_DHCP +#define CONFIG_BOOTP_SERVERIP + +#define CONFIG_MII /* MII PHY management */ +#define CONFIG_TSEC1_NAME "eTSEC1" +#define CONFIG_TSEC2_NAME "eTSEC2" +#define CONFIG_TSEC3_NAME "eTSEC3" + +#define TSEC1_PHY_ADDR 4 +#define TSEC2_PHY_ADDR 0 +#define TSEC2_PHY_ADDR_SGMII 0x00 +#define TSEC3_PHY_ADDR 6 + +#define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) +#define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) +#define TSEC3_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) + +#define TSEC1_PHYIDX 0 +#define TSEC2_PHYIDX 0 +#define TSEC3_PHYIDX 0 + +#define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */ + +#endif + +#define CONFIG_HOSTNAME UCP1020 +#define CONFIG_ROOTPATH "/opt/nfsroot" +#define CONFIG_BOOTFILE "uImage" +#define CONFIG_UBOOTPATH u-boot.bin /* U-Boot image on TFTP server */ + +/* default location for tftp and bootm */ +#define CONFIG_LOADADDR 1000000 + +/* + * Autobooting + */ +#define CONFIG_AUTOBOOT_KEYED +#define CONFIG_AUTOBOOT_STOP_STR "\x1b" +#define DEBUG_BOOTKEYS 0 +#undef CONFIG_AUTOBOOT_DELAY_STR +#undef CONFIG_BOOTARGS +#define CONFIG_AUTOBOOT_PROMPT "Autobooting in %d seconds, " \ + "press \"\" to stop\n", bootdelay + +#define CONFIG_BOOTARGS /* the boot command will set bootargs */ + +#define CONFIG_BAUDRATE 115200 + +#if defined(CONFIG_DONGLE) + +#define CONFIG_BOOTDELAY 1 /* autoboot after 1 seconds */ +#define CONFIG_EXTRA_ENV_SETTINGS \ +"bootcmd=run prog_spi_mbrbootcramfs\0" \ +"bootfile=uImage\0" \ +"consoledev=ttyS0\0" \ +"cramfsfile=image.cramfs\0" \ +"dtbaddr=0x00c00000\0" \ +"dtbfile=image.dtb\0" \ +"ethaddr=" __stringify(CONFIG_ETHADDR) "\0" \ +"eth1addr=" __stringify(CONFIG_ETH1ADDR) "\0" \ +"eth2addr=" __stringify(CONFIG_ETH2ADDR) "\0" \ +"fileaddr=0x01000000\0" \ +"filesize=0x00080000\0" \ +"flashmbr=sf probe 0; " \ + "tftp $loadaddr $mbr; " \ + "sf erase $mbr_offset +$filesize; " \ + "sf write $loadaddr $mbr_offset $filesize\0" \ +"flashrecovery=tftp $recoveryaddr $cramfsfile; " \ + "protect off $nor_recoveryaddr +$filesize; " \ + "erase $nor_recoveryaddr +$filesize; " \ + "cp.b $recoveryaddr $nor_recoveryaddr $filesize; " \ + "protect on $nor_recoveryaddr +$filesize\0 " \ +"flashuboot=tftp $ubootaddr $ubootfile; " \ + "protect off $nor_ubootaddr +$filesize; " \ + "erase $nor_ubootaddr +$filesize; " \ + "cp.b $ubootaddr $nor_ubootaddr $filesize; " \ + "protect on $nor_ubootaddr +$filesize\0 " \ +"flashworking=tftp $workingaddr $cramfsfile; " \ + "protect off $nor_workingaddr +$filesize; " \ + "erase $nor_workingaddr +$filesize; " \ + "cp.b $workingaddr $nor_workingaddr $filesize; " \ + "protect on $nor_workingaddr +$filesize\0 " \ +"hwconfig=usb1:dr_mode=host,phy_type=ulpi\0 " \ +"kerneladdr=0x01100000\0" \ +"kernelfile=uImage\0" \ +"loadaddr=0x01000000\0" \ +"mbr=uCP1020d.mbr\0" \ +"mbr_offset=0x00000000\0" \ +"mmbr=uCP1020Quiet.mbr\0" \ +"mmcpart=0:2\0" \ +"mmc__mbrd=fatload mmc $mmcpart $loadaddr $mbr; " \ + "mmc erase 1 1; " \ + "mmc write $loadaddr 1 1\0" \ +"mmc__uboot=fatload mmc $mmcpart $loadaddr $ubootfile; " \ + "mmc erase 0x40 0x400; " \ + "mmc write $loadaddr 0x40 0x400\0" \ +"netdev=eth0\0" \ +"nor_recoveryaddr=0xEC0A0000\0" \ +"nor_ubootaddr=0xEFF80000\0" \ +"nor_workingaddr=0xECFA0000\0" \ +"norbootrecovery=setenv bootargs $recoverybootargs" \ + " console=$consoledev,$baudrate $othbootargs; " \ + "run norloadrecovery; " \ + "bootm $kerneladdr - $dtbaddr\0" \ +"norbootworking=setenv bootargs $workingbootargs" \ + " console=$consoledev,$baudrate $othbootargs; " \ + "run norloadworking; " \ + "bootm $kerneladdr - $dtbaddr\0" \ +"norloadrecovery=mw.l $kerneladdr 0x0 0x00a00000; " \ + "setenv cramfsaddr $nor_recoveryaddr; " \ + "cramfsload $dtbaddr $dtbfile; " \ + "cramfsload $kerneladdr $kernelfile\0" \ +"norloadworking=mw.l $kerneladdr 0x0 0x00a00000; " \ + "setenv cramfsaddr $nor_workingaddr; " \ + "cramfsload $dtbaddr $dtbfile; " \ + "cramfsload $kerneladdr $kernelfile\0" \ +"prog_spi_mbr=run spi__mbr\0" \ +"prog_spi_mbrboot=run spi__mbr; run spi__boot1; run spi__boot2\0" \ +"prog_spi_mbrbootcramfs=run spi__mbr; run spi__boot1; run spi__boot2; " \ + "run spi__cramfs\0" \ +"ramboot=setenv bootargs root=/dev/ram ramdisk_size=$ramdisk_size ro" \ + " console=$consoledev,$baudrate $othbootargs; " \ + "tftp $rootfsaddr $rootfsfile; " \ + "tftp $loadaddr $kernelfile; " \ + "tftp $dtbaddr $dtbfile; " \ + "bootm $loadaddr $rootfsaddr $dtbaddr\0" \ +"ramdisk_size=120000\0" \ +"ramdiskfile=rootfs.ext2.gz.uboot\0" \ +"recoveryaddr=0x02F00000\0" \ +"recoverybootargs=root=/dev/mtdblock0 rootfstype=cramfs ro\0" \ +"releasefpga=mw.l 0xffe0f000 0x00400000; mw.l 0xffe0f004 0x00000000; " \ + "mw.l 0xffe0f008 0x00400000\0" \ +"rootfsaddr=0x02F00000\0" \ +"rootfsfile=rootfs.ext2.gz.uboot\0" \ +"rootpath=/opt/nfsroot\0" \ +"spi__boot1=fatload mmc $mmcpart $loadaddr u-boot.bin; " \ + "protect off 0xeC000000 +$filesize; " \ + "erase 0xEC000000 +$filesize; " \ + "cp.b $loadaddr 0xEC000000 $filesize; " \ + "cmp.b $loadaddr 0xEC000000 $filesize; " \ + "protect on 0xeC000000 +$filesize\0" \ +"spi__boot2=fatload mmc $mmcpart $loadaddr u-boot.bin; " \ + "protect off 0xeFF80000 +$filesize; " \ + "erase 0xEFF80000 +$filesize; " \ + "cp.b $loadaddr 0xEFF80000 $filesize; " \ + "cmp.b $loadaddr 0xEFF80000 $filesize; " \ + "protect on 0xeFF80000 +$filesize\0" \ +"spi__bootd=fatload mmc $mmcpart $loadaddr $ubootd; " \ + "sf probe 0; sf erase 0x8000 +$filesize; " \ + "sf write $loadaddr 0x8000 $filesize\0" \ +"spi__cramfs=fatload mmc $mmcpart $loadaddr image.cramfs; " \ + "protect off 0xec0a0000 +$filesize; " \ + "erase 0xeC0A0000 +$filesize; " \ + "cp.b $loadaddr 0xeC0A0000 $filesize; " \ + "protect on 0xec0a0000 +$filesize\0" \ +"spi__mbr=fatload mmc $mmcpart $loadaddr $mmbr; " \ + "sf probe 1; sf erase 0 +$filesize; " \ + "sf write $loadaddr 0 $filesize\0" \ +"spi__mbrd=fatload mmc $mmcpart $loadaddr $mbr; " \ + "sf probe 0; sf erase 0 +$filesize; " \ + "sf write $loadaddr 0 $filesize\0" \ +"tftpflash=tftpboot $loadaddr $uboot; " \ + "protect off " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \ + "erase " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \ + "cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " $filesize; " \ + "protect on " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \ + "cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " $filesize\0"\ +"uboot= " __stringify(CONFIG_UBOOTPATH) "\0" \ +"ubootaddr=0x01000000\0" \ +"ubootfile=u-boot.bin\0" \ +"ubootd=u-boot4dongle.bin\0" \ +"upgrade=run flashworking\0" \ +"usb_phy_type=ulpi\0 " \ +"workingaddr=0x02F00000\0" \ +"workingbootargs=root=/dev/mtdblock1 rootfstype=cramfs ro\0" + +#else + +#if defined(CONFIG_UCP1020T1) + +#define CONFIG_BOOTDELAY 2 /* autoboot after 2 sec, -1 disables auto-boot */ +#define CONFIG_EXTRA_ENV_SETTINGS \ +"bootcmd=run releasefpga; run norbootworking || run norbootrecovery\0" \ +"bootfile=uImage\0" \ +"consoledev=ttyS0\0" \ +"cramfsfile=image.cramfs\0" \ +"dtbaddr=0x00c00000\0" \ +"dtbfile=image.dtb\0" \ +"ethaddr=" __stringify(CONFIG_ETHADDR) "\0" \ +"eth1addr=" __stringify(CONFIG_ETH1ADDR) "\0" \ +"eth2addr=" __stringify(CONFIG_ETH2ADDR) "\0" \ +"fileaddr=0x01000000\0" \ +"filesize=0x00080000\0" \ +"flashmbr=sf probe 0; " \ + "tftp $loadaddr $mbr; " \ + "sf erase $mbr_offset +$filesize; " \ + "sf write $loadaddr $mbr_offset $filesize\0" \ +"flashrecovery=tftp $recoveryaddr $cramfsfile; " \ + "protect off $nor_recoveryaddr +$filesize; " \ + "erase $nor_recoveryaddr +$filesize; " \ + "cp.b $recoveryaddr $nor_recoveryaddr $filesize; " \ + "protect on $nor_recoveryaddr +$filesize\0 " \ +"flashuboot=tftp $ubootaddr $ubootfile; " \ + "protect off $nor_ubootaddr +$filesize; " \ + "erase $nor_ubootaddr +$filesize; " \ + "cp.b $ubootaddr $nor_ubootaddr $filesize; " \ + "protect on $nor_ubootaddr +$filesize\0 " \ +"flashworking=tftp $workingaddr $cramfsfile; " \ + "protect off $nor_workingaddr +$filesize; " \ + "erase $nor_workingaddr +$filesize; " \ + "cp.b $workingaddr $nor_workingaddr $filesize; " \ + "protect on $nor_workingaddr +$filesize\0 " \ +"hwconfig=usb1:dr_mode=host,phy_type=ulpi\0 " \ +"kerneladdr=0x01100000\0" \ +"kernelfile=uImage\0" \ +"loadaddr=0x01000000\0" \ +"mbr=uCP1020.mbr\0" \ +"mbr_offset=0x00000000\0" \ +"netdev=eth0\0" \ +"nor_recoveryaddr=0xEC0A0000\0" \ +"nor_ubootaddr=0xEFF80000\0" \ +"nor_workingaddr=0xECFA0000\0" \ +"norbootrecovery=setenv bootargs $recoverybootargs" \ + " console=$consoledev,$baudrate $othbootargs; " \ + "run norloadrecovery; " \ + "bootm $kerneladdr - $dtbaddr\0" \ +"norbootworking=setenv bootargs $workingbootargs" \ + " console=$consoledev,$baudrate $othbootargs; " \ + "run norloadworking; " \ + "bootm $kerneladdr - $dtbaddr\0" \ +"norloadrecovery=mw.l $kerneladdr 0x0 0x00a00000; " \ + "setenv cramfsaddr $nor_recoveryaddr; " \ + "cramfsload $dtbaddr $dtbfile; " \ + "cramfsload $kerneladdr $kernelfile\0" \ +"norloadworking=mw.l $kerneladdr 0x0 0x00a00000; " \ + "setenv cramfsaddr $nor_workingaddr; " \ + "cramfsload $dtbaddr $dtbfile; " \ + "cramfsload $kerneladdr $kernelfile\0" \ +"othbootargs=quiet\0" \ +"ramboot=setenv bootargs root=/dev/ram ramdisk_size=$ramdisk_size ro" \ + " console=$consoledev,$baudrate $othbootargs; " \ + "tftp $rootfsaddr $rootfsfile; " \ + "tftp $loadaddr $kernelfile; " \ + "tftp $dtbaddr $dtbfile; " \ + "bootm $loadaddr $rootfsaddr $dtbaddr\0" \ +"ramdisk_size=120000\0" \ +"ramdiskfile=rootfs.ext2.gz.uboot\0" \ +"recoveryaddr=0x02F00000\0" \ +"recoverybootargs=root=/dev/mtdblock0 rootfstype=cramfs ro\0" \ +"releasefpga=mw.l 0xffe0f000 0x00400000; mw.l 0xffe0f004 0x00000000; " \ + "mw.l 0xffe0f008 0x00400000\0" \ +"rootfsaddr=0x02F00000\0" \ +"rootfsfile=rootfs.ext2.gz.uboot\0" \ +"rootpath=/opt/nfsroot\0" \ +"silent=1\0" \ +"tftpflash=tftpboot $loadaddr $uboot; " \ + "protect off " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \ + "erase " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \ + "cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " $filesize; " \ + "protect on " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \ + "cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " $filesize\0"\ +"uboot= " __stringify(CONFIG_UBOOTPATH) "\0" \ +"ubootaddr=0x01000000\0" \ +"ubootfile=u-boot.bin\0" \ +"upgrade=run flashworking\0" \ +"workingaddr=0x02F00000\0" \ +"workingbootargs=root=/dev/mtdblock1 rootfstype=cramfs ro\0" + +#else /* For Arcturus Modules */ + +#define CONFIG_BOOTDELAY 2 /* autoboot after 2 sec, -1 disables auto-boot */ +#define CONFIG_EXTRA_ENV_SETTINGS \ +"bootcmd=run norkernel\0" \ +"bootfile=uImage\0" \ +"consoledev=ttyS0\0" \ +"dtbaddr=0x00c00000\0" \ +"dtbfile=image.dtb\0" \ +"ethaddr=" __stringify(CONFIG_ETHADDR) "\0" \ +"eth1addr=" __stringify(CONFIG_ETH1ADDR) "\0" \ +"eth2addr=" __stringify(CONFIG_ETH2ADDR) "\0" \ +"fileaddr=0x01000000\0" \ +"filesize=0x00080000\0" \ +"flashmbr=sf probe 0; " \ + "tftp $loadaddr $mbr; " \ + "sf erase $mbr_offset +$filesize; " \ + "sf write $loadaddr $mbr_offset $filesize\0" \ +"flashuboot=tftp $loadaddr $ubootfile; " \ + "protect off $nor_ubootaddr0 +$filesize; " \ + "erase $nor_ubootaddr0 +$filesize; " \ + "cp.b $loadaddr $nor_ubootaddr0 $filesize; " \ + "protect on $nor_ubootaddr0 +$filesize; " \ + "protect off $nor_ubootaddr1 +$filesize; " \ + "erase $nor_ubootaddr1 +$filesize; " \ + "cp.b $loadaddr $nor_ubootaddr1 $filesize; " \ + "protect on $nor_ubootaddr1 +$filesize\0 " \ +"format0=protect off $part0base +$part0size; " \ + "erase $part0base +$part0size\0" \ +"format1=protect off $part1base +$part1size; " \ + "erase $part1base +$part1size\0" \ +"format2=protect off $part2base +$part2size; " \ + "erase $part2base +$part2size\0" \ +"format3=protect off $part3base +$part3size; " \ + "erase $part3base +$part3size\0" \ +"hwconfig=usb1:dr_mode=host,phy_type=ulpi\0 " \ +"kerneladdr=0x01100000\0" \ +"kernelargs=root=/dev/mtdblock1 rootfstype=cramfs ro\0" \ +"kernelfile=uImage\0" \ +"loadaddr=0x01000000\0" \ +"mbr=uCP1020.mbr\0" \ +"mbr_offset=0x00000000\0" \ +"netdev=eth0\0" \ +"nor_ubootaddr0=0xEC000000\0" \ +"nor_ubootaddr1=0xEFF80000\0" \ +"norkernel=setenv bootargs $kernelargs console=$consoledev,$baudrate; " \ + "run norkernelload; " \ + "bootm $kerneladdr - $dtbaddr\0" \ +"norkernelload=mw.l $kerneladdr 0x0 0x00a00000; " \ + "setenv cramfsaddr $part0base; " \ + "cramfsload $dtbaddr $dtbfile; " \ + "cramfsload $kerneladdr $kernelfile\0" \ +"part0base=0xEC100000\0" \ +"part0size=0x00700000\0" \ +"part1base=0xEC800000\0" \ +"part1size=0x02000000\0" \ +"part2base=0xEE800000\0" \ +"part2size=0x00800000\0" \ +"part3base=0xEF000000\0" \ +"part3size=0x00F80000\0" \ +"partENVbase=0xEC080000\0" \ +"partENVsize=0x00080000\0" \ +"program0=tftp part0-000000.bin; " \ + "protect off $part0base +$filesize; " \ + "erase $part0base +$filesize; " \ + "cp.b $loadaddr $part0base $filesize; " \ + "echo Verifying...; " \ + "cmp.b $loadaddr $part0base $filesize\0" \ +"program1=tftp part1-000000.bin; " \ + "protect off $part1base +$filesize; " \ + "erase $part1base +$filesize; " \ + "cp.b $loadaddr $part1base $filesize; " \ + "echo Verifying...; " \ + "cmp.b $loadaddr $part1base $filesize\0" \ +"program2=tftp part2-000000.bin; " \ + "protect off $part2base +$filesize; " \ + "erase $part2base +$filesize; " \ + "cp.b $loadaddr $part2base $filesize; " \ + "echo Verifying...; " \ + "cmp.b $loadaddr $part2base $filesize\0" \ +"ramboot=setenv bootargs root=/dev/ram ramdisk_size=$ramdisk_size ro" \ + " console=$consoledev,$baudrate $othbootargs; " \ + "tftp $rootfsaddr $rootfsfile; " \ + "tftp $loadaddr $kernelfile; " \ + "tftp $dtbaddr $dtbfile; " \ + "bootm $loadaddr $rootfsaddr $dtbaddr\0" \ +"ramdisk_size=120000\0" \ +"ramdiskfile=rootfs.ext2.gz.uboot\0" \ +"releasefpga=mw.l 0xffe0f000 0x00400000; mw.l 0xffe0f004 0x00000000; " \ + "mw.l 0xffe0f008 0x00400000\0" \ +"rootfsaddr=0x02F00000\0" \ +"rootfsfile=rootfs.ext2.gz.uboot\0" \ +"rootpath=/opt/nfsroot\0" \ +"spi__mbr=fatload mmc $mmcpart $loadaddr $mmbr; " \ + "sf probe 0; sf erase 0 +$filesize; " \ + "sf write $loadaddr 0 $filesize\0" \ +"spi__boot=fatload mmc $mmcpart $loadaddr u-boot.bin; " \ + "protect off 0xeC000000 +$filesize; " \ + "erase 0xEC000000 +$filesize; " \ + "cp.b $loadaddr 0xEC000000 $filesize; " \ + "cmp.b $loadaddr 0xEC000000 $filesize; " \ + "protect on 0xeC000000 +$filesize\0" \ +"tftpflash=tftpboot $loadaddr $uboot; " \ + "protect off " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \ + "erase " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \ + "cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " $filesize; " \ + "protect on " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \ + "cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " $filesize\0"\ +"uboot= " __stringify(CONFIG_UBOOTPATH) "\0" \ +"ubootfile=u-boot.bin\0" \ +"upgrade=run flashuboot\0" \ +"usb_phy_type=ulpi\0 " \ +"boot_nfs= " \ + "setenv bootargs root=/dev/nfs rw " \ + "nfsroot=$serverip:$rootpath " \ + "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ + "console=$consoledev,$baudrate $othbootargs;" \ + "tftp $loadaddr $bootfile;" \ + "tftp $fdtaddr $fdtfile;" \ + "bootm $loadaddr - $fdtaddr\0" \ +"boot_hd = " \ + "setenv bootargs root=/dev/$bdev rw rootdelay=30 " \ + "console=$consoledev,$baudrate $othbootargs;" \ + "usb start;" \ + "ext2load usb 0:1 $loadaddr /boot/$bootfile;" \ + "ext2load usb 0:1 $fdtaddr /boot/$fdtfile;" \ + "bootm $loadaddr - $fdtaddr\0" \ +"boot_usb_fat = " \ + "setenv bootargs root=/dev/ram rw " \ + "console=$consoledev,$baudrate $othbootargs " \ + "ramdisk_size=$ramdisk_size;" \ + "usb start;" \ + "fatload usb 0:2 $loadaddr $bootfile;" \ + "fatload usb 0:2 $fdtaddr $fdtfile;" \ + "fatload usb 0:2 $ramdiskaddr $ramdiskfile;" \ + "bootm $loadaddr $ramdiskaddr $fdtaddr\0 " \ +"boot_usb_ext2 = " \ + "setenv bootargs root=/dev/ram rw " \ + "console=$consoledev,$baudrate $othbootargs " \ + "ramdisk_size=$ramdisk_size;" \ + "usb start;" \ + "ext2load usb 0:4 $loadaddr $bootfile;" \ + "ext2load usb 0:4 $fdtaddr $fdtfile;" \ + "ext2load usb 0:4 $ramdiskaddr $ramdiskfile;" \ + "bootm $loadaddr $ramdiskaddr $fdtaddr\0 " \ +"boot_nor = " \ + "setenv bootargs root=/dev/$jffs2nor rw " \ + "console=$consoledev,$baudrate rootfstype=jffs2 $othbootargs;" \ + "bootm $norbootaddr - $norfdtaddr\0 " \ +"boot_ram = " \ + "setenv bootargs root=/dev/ram rw " \ + "console=$consoledev,$baudrate $othbootargs " \ + "ramdisk_size=$ramdisk_size;" \ + "tftp $ramdiskaddr $ramdiskfile;" \ + "tftp $loadaddr $bootfile;" \ + "tftp $fdtaddr $fdtfile;" \ + "bootm $loadaddr $ramdiskaddr $fdtaddr\0" + +#endif +#endif + +#endif /* __CONFIG_H */ -- 2.39.5