From d4599b8b3f0c568961d6007e59633456a13a9c18 Mon Sep 17 00:00:00 2001 From: Uwe Hermann Date: Fri, 14 Oct 2011 00:13:47 +0200 Subject: [PATCH] Add a board file for the Glyn Tonga2. This is a Toshiba TMPA900CMXBG (ARM9) based SO-DIMM CPU module with 64MB DDR SDRAM, 256MB NAND flash, and on-board Ethernet. The board file provides a tonga2_init function which sets up the PLL/clocks and memory (SDRAM and SRAM), which allows writing a boot-loader into RAM via JTAG. Change-Id: I60522b97997bdf50e1f25aebab910d93a98522fb Signed-off-by: Uwe Hermann Reviewed-on: http://openocd.zylin.com/19 Reviewed-by: Spencer Oliver Tested-by: Spencer Oliver --- tcl/board/glyn_tonga2.cfg | 170 ++++++++++++++++++++++++++++++++++++++ 1 file changed, 170 insertions(+) create mode 100644 tcl/board/glyn_tonga2.cfg diff --git a/tcl/board/glyn_tonga2.cfg b/tcl/board/glyn_tonga2.cfg new file mode 100644 index 00000000..783ef9fa --- /dev/null +++ b/tcl/board/glyn_tonga2.cfg @@ -0,0 +1,170 @@ +# +# Glyn Tonga2 SO-DIMM CPU module (Toshiba TMPA900CMXBG, ARM9) +# +# http://toshiba-mikrocontroller.de/sites/TMPA900CPUBOARDStarter.htm +# +# Hardware on the S0-DIMM module: +# - Toshiba TMPA900CMXBG (ARM9, ARM926EJ-S, max. 200MHz) +# - DDR SDRAM: Hynix H5MS5162DFR-J3M (64Mbyte, x16, 1.8V, 166/83MHz at CL3/2) +# - NAND flash: Samsung K9F2G08U0B-PIB0 (256M x 8 Bit, 3.3V) +# - Ethernet: SMSC LAN9221I-ABZJ (10/100Mbit, Non-PCI, 16 bit interface) +# + +source [find target/tmpa900.cfg] + +######################## +# Target configuration # +######################## + +$_TARGETNAME configure -event reset-init { tonga2_init } + +proc tonga2_init { } { + + ###################### + # PLL initialization # + ###################### + + # Clock overview (see datasheet chapter 3.5.2, page 57): + # - fs: Low-frequency oscillator + # - fOSCH: High-frequency oscillator (24MHz on this board) + # - fPLL = fOSCH * multiplier (where multiplier can be 6 or 8) + # - fFCLK = fPLL / gear (where gear can be 1/2/4/8) + # - fHCLK is always fFCLK/2. fPCLK is also fFCLK/2. + # + # We select multiplier = 8 and gear = 1, so + # fFCLK = fOSCH * 8 / 1 = 192MHz. + + # SYSCR3 (System Control Register 3): Disable and configure PLL. + # - PLL operation control: off + # - PLL constant value setting 1: always 0, as per datasheet + # - PLL constant value setting 2: x8 (multiplier = 8) + mww 0xf005000c 0x00000007 + + # SYSCR4 (System Control Register 4): Configure PLL. + # - PLL constant value setting 3: 140MHz or more + # - PLL constant value setting 4: always 1, as per datasheet + # - PLL constant value setting 5: 140MHz or more + mww 0xf0050010 0x00000065 + + # SYSCR3 (System Control Register 3): Enable PLL. + # - PLL operation control: on + # - All other bits remain set as above. + mww 0xf005000c 0x00000087 + + # Wait for PLL to stabilize. + sleep 10 + + # SYSCR2 (System Control Register 2): Switch from fOSCH to fPLL. + # - Selection of the PLL output clock: fPLL + mww 0xf0050008 0x00000002 + + # SYSCR1 (System Control Register 1): + # - Clock gear programming: fc/1 (i.e., gear = 1, don't divide). + mww 0xf0050004 0x00000000 + + # CLKCR5 (Clock Control Register 5): Set bits 3 and 6. The datasheet + # says the bits are reserved, but also recommends "Write as one". + mww 0xf0050054 0x00000048 + + + ############################################################## + # Dynamic Memory Controller (DMC) / DDR SDRAM initialization # + ############################################################## + + # PMC (Power Management Controller): + # PMCDRV (External Port "Driverbility" control register): + # Bits DRV_MEM0/DRV_MEM1 (memory relation port drive power): + mww 0xf0020260 0x00000003 ;# Select 1.8V +/- 0.1V + + # Setup DDR SDRAM timing parameters for our specific chip. + mww 0xf4310014 0x00000004 ;# cas_latency = 2 + mww 0xf4310018 0x00000001 ;# t_dqss = 1 + mww 0xf431001c 0x00000002 ;# t_mrd = 2 + mww 0xf4310020 0x0000000a ;# t_ras = 10 + mww 0xf4310024 0x0000000a ;# t_rc = 10 + mww 0xf4310028 0x00000013 ;# t_rcd = 3, schedule_rcd = 2 + mww 0xf431002c 0x0000010a ;# t_rfc = 10, schedule_rfc = 8 + mww 0xf4310030 0x00000013 ;# t_rp = 3, schedule_rp = 2 + mww 0xf4310034 0x00000002 ;# t_rrd = 2 + mww 0xf4310038 0x00000002 ;# t_wr = 2 + mww 0xf431003c 0x00000001 ;# t_wtr = 1 + mww 0xf4310040 0x0000000a ;# t_xp = 10 + mww 0xf4310044 0x0000000c ;# t_xsr = 12 + mww 0xf4310048 0x00000014 ;# t_esr = 20 + + # dmc_memory_cfg_5 (DMC Memory Configuration register): + # Set memory configuration: + # column_bits = 10, row_bits = 13, ap-bit = 10, power_down_prd = 0, + # auto_power_down = disable, stop_mem_clock = disable, memory_burst = 4 + mww 0xf431000c 0x00010012 + + # dmc_user_config_5 (DMC user_config register): + # Data bus width of DDR SDRAM: 16 bit + mww 0xf4310304 0x00000058 + + # dmc_refresh_prd_5 (DMC Refresh Period register): + # Auto refresh: every 2656 (0xa60) DMCSCLK periods. + mww 0xf4310010 0x00000a60 + + # dmc_chip_0_cfg_5 (DMC chip_0_cfg registers): + # - SDRAM address structure: bank, row, column + # - address_match = 01000000 (start address [31:24]) + # - address_mask = 11111100 (start address [31:24] mask value) + mww 0xf4310200 0x000140fc + + # Initialize the DDR SDRAM chip. + # dmc_direct_cmd_5 (DMC Direct Command register). + # See datasheet chapter 3.10.5.1, page 268. + mww 0xf4310008 0x000c0000 ;# RAM init: NOP + mww 0xf4310008 0x00000000 ;# RAM init: Precharge all + mww 0xf4310008 0x00040000 ;# RAM init: Autorefresh + mww 0xf4310008 0x00040000 ;# RAM init: Autorefresh + mww 0xf4310008 0x00080032 ;# RAM init: addr_13_to_0 = 0x32 + mww 0xf4310008 0x000c0000 ;# RAM init: NOP + mww 0xf4310008 0x000a0000 ;# RAM init: bank_addr = bank 2 + + # dmc_id_<0-5>_cfg_5 (DMC id_<0-5>_cfg registers): + # Set min./max. QoS values. + # - 0x5: Enable QoS, max. QoS = 1 + # - 0xb: Enable QoS, min. QoS = 2 + mww 0xf4310100 0x00000005 ;# AHB0: CPU Data + mww 0xf4310104 0x00000005 ;# AHB1: CPU Inst + mww 0xf4310108 0x0000000b ;# AHB2: LCDC + mww 0xf431010c 0x00000005 ;# AHB3: LCDDA, USB + mww 0xf4310110 0x00000005 ;# AHB4: DMA1 + mww 0xf4310114 0x00000005 ;# AHB5: DMA2 + + # dmc_memc_cmd_5 (DMC Memory Controller Command register): + # Change DMC state to ready. + mww 0xf4310004 0x00000000 ;# memc_cmd = "Go" + + # EBI: SMC Timeout register + mww 0xf00a0050 0x00000001 ;# smc_timeout = 1 + + + ######################################################## + # Static Memory Controller (SMC) / SRAM initialization # + ######################################################## + + # smc_set_cycles_5 (SMC Set Cycles register): + # tRC = 10, tWC = 10, tCEOE = 7, tWP = 5, tPC=2, tTR=2 + mww 0xf4311014 0x0004afaa + + # smc_set_opmode_5 (SMC Set Opmode register): + # Memory data bus width = 16 bits, async read mode, read burst + # length = 1 beat, async write mode, write burst length = 1 beat, + # byte enable (SMCBE0-1) timing = SMCCSn timing, memory burst boundary + # split setting = burst can cross any address boundary + mww 0xf4311018 0x00000001 + + # smc_direct_cmd_5 (SMC Direct Command register): + # cmd_type = UpdateRegs, chip_select = CS1 + mww 0xf4311010 0x00c00000 +} + +####################### +# Flash configuration # +####################### + +# TODO: Implement NAND support. + -- 2.39.5