--- /dev/null
+/** ###################################################################\r
+** THIS BEAN MODULE IS GENERATED BY THE TOOL. DO NOT MODIFY IT.\r
+** Filename : COM0.C\r
+** Project : RTOSDemo\r
+** Processor : MC9S12DP256BCPV\r
+** Beantype : AsynchroSerial\r
+** Version : Bean 02.231, Driver 01.08, CPU db: 2.87.283\r
+** Compiler : Metrowerks HC12 C Compiler\r
+** Date/Time : 19/06/2005, 15:07\r
+** Abstract :\r
+** This bean "AsynchroSerial" implements an asynchronous serial\r
+** communication. The bean supports different settings of \r
+** parity, word width, stop-bit and communication speed,\r
+** user can select interrupt or polling handler.\r
+** Communication speed can be changed also in runtime.\r
+** The bean requires one on-chip asynchronous serial channel.\r
+** Settings :\r
+** Serial channel : SCI0\r
+**\r
+** Protocol\r
+** Init baud rate : 38400baud\r
+** Width : 8 bits\r
+** Stop bits : 1\r
+** Parity : none\r
+** Breaks : Disabled\r
+**\r
+** Registers\r
+** Input buffer : SCI0DRL [207]\r
+** Output buffer : SCI0DRL [207]\r
+** Control register : SCI0CR1 [202]\r
+** Mode register : SCI0CR2 [203]\r
+** Baud setting reg. : SCI0BD [200]\r
+** Special register : SCI0SR1 [204]\r
+**\r
+** Input interrupt\r
+** Vector name : INT_SCI0\r
+** Priority : 1\r
+**\r
+** Output interrupt\r
+** Vector name : INT_SCI0\r
+** Priority : 1\r
+**\r
+** Used pins : \r
+** ----------------------------------------------------\r
+** Function | On package | Name\r
+** ----------------------------------------------------\r
+** Input | 89 | PS0_RxD0\r
+** Output | 90 | PS1_TxD0\r
+** ----------------------------------------------------\r
+**\r
+**\r
+** Used baud modes :\r
+** ----------------------------------------------------\r
+** No. | Mode ID | Baud rate\r
+** ----------------------------------------------------\r
+** 0 | Bm_38400baud | 38400baud\r
+** 1 | Bm_19200baud | 19200baud\r
+** 2 | Bm_9600baud | 9600baud\r
+** 3 | Bm_4800baud | 4800baud\r
+** ----------------------------------------------------\r
+** Contents :\r
+** SetBaudRateMode - byte COM0_SetBaudRateMode(byte Mod);\r
+**\r
+** (c) Copyright UNIS, spol. s r.o. 1997-2002\r
+** UNIS, spol. s r.o.\r
+** Jundrovska 33\r
+** 624 00 Brno\r
+** Czech Republic\r
+** http : www.processorexpert.com\r
+** mail : info@processorexpert.com\r
+** ###################################################################*/\r
+\r
+/* MODULE COM0. */\r
+\r
+#pragma MESSAGE DISABLE C4002 /* WARNING C4002: Result not used is ignored */\r
+#pragma MESSAGE DISABLE C4301 /* INFORMATION C4301: Inline expansion done for function call */\r
+\r
+#include "COM0.h"\r
+#include "TickTimer.h"\r
+#include "Byte1.h"\r
+\r
+/* Definition of DATA and CODE segments for this bean. User can specify where\r
+ these segments will be located on "Build options" tab of the selected CPU bean. */\r
+#pragma DATA_SEG COM0_DATA /* Data section for this module. */\r
+#pragma CODE_SEG COM0_CODE /* Code section for this module. */\r
+\r
+\r
+#define OVERRUN_ERR 1 /* Overrun error flag bit */\r
+#define FRAMING_ERR 2 /* Framing error flag bit */\r
+#define PARITY_ERR 4 /* Parity error flag bit */\r
+#define CHAR_IN_RX 8 /* Char is in RX buffer */\r
+#define FULL_TX 16 /* Full transmit buffer */\r
+#define RUNINT_FROM_TX 32 /* Interrupt is in progress */\r
+#define FULL_RX 64 /* Full receive buffer */\r
+#define NOISE_ERR 128 /* Noise erorr flag bit */\r
+#define IDLE_ERR 256 /* Idle character flag bit */\r
+#define BREAK_ERR 512 /* Break detect */\r
+\r
+static word SerFlag; /* Flags for serial communication */\r
+ /* Bits: 0 - OverRun error */\r
+ /* 1 - Framing error */\r
+ /* 2 - Parity error */\r
+ /* 3 - Char in RX buffer */\r
+ /* 4 - Full TX buffer */\r
+ /* 5 - Running int from TX */\r
+ /* 6 - Full RX buffer */\r
+ /* 7 - Noise error */\r
+ /* 8 - Idle character */\r
+ /* 9 - Break detected */\r
+ /* 10 - Unused */\r
+static word PrescHigh;\r
+static byte NumMode; /* Number of selected baud mode */\r
+\r
+\r
+/*\r
+** ===================================================================\r
+** Method : HWEnDi (bean AsynchroSerial)\r
+**\r
+** Description :\r
+** This method is internal. It is used by Processor Expert\r
+** only.\r
+** ===================================================================\r
+*/\r
+static void HWEnDi(void)\r
+{\r
+ SCI0CR2_TE = 1; /* Enable transmitter */\r
+ SCI0CR2_RE = 1; /* Enable receiver */\r
+ SCI0CR2_RIE = 1; /* Enable recieve interrupt */\r
+}\r
+\r
+/*\r
+** ===================================================================\r
+** Method : COM0_SetBaudRateMode (bean AsynchroSerial)\r
+**\r
+** Description :\r
+** This method changes the channel communication speed (baud\r
+** rate). This method can be used only if you specify a list\r
+** of possible period settings at design time (see <Timing\r
+** dialog box> - Runtime setting - from a list of values).\r
+** Each of these settings constitutes a mode and Processor\r
+** Expert^[TM] assigns them a mode identifier. The prescaler\r
+** and compare values corresponding to each mode are\r
+** calculated at design time. You may switch modes at\r
+** runtime by referring only to a mode identifier. No\r
+** run-time calculations are performed, all the calculations\r
+** are performed at design time.\r
+** Parameters :\r
+** NAME - DESCRIPTION\r
+** Mod - Timing mode to set\r
+** Returns :\r
+** --- - Error code, possible codes:\r
+** ERR_OK - OK\r
+** ERR_SPEED - This device does not work in\r
+** the active speed mode\r
+** ===================================================================\r
+*/\r
+byte COM0_SetBaudRateMode(byte Mod)\r
+{\r
+ static const word COM0_PrescHigh[4] = {41,81,163,326};\r
+\r
+ if(Mod >= 4) /* Is mode in baud mode list */\r
+ return ERR_VALUE; /* If no then error */\r
+ NumMode = Mod; /* New baud mode */\r
+ PrescHigh = COM0_PrescHigh[Mod]; /* Prescaler in high speed mode */\r
+ SCI0BD = PrescHigh; /* Set prescaler bits */\r
+ return ERR_OK; /* OK */\r
+}\r
+\r
+/*\r
+** ===================================================================\r
+** Method : COM0_Init (bean AsynchroSerial)\r
+**\r
+** Description :\r
+** This method is internal. It is used by Processor Expert\r
+** only.\r
+** ===================================================================\r
+*/\r
+void COM0_Init(void)\r
+{\r
+ PrescHigh = 41; /* Precaler in high speed mode */\r
+ SerFlag = 0; /* Reset flags */\r
+ NumMode = 0; /* Number of selected baud mode */\r
+ /* SCI0CR1: LOOPS=0,SCISWAI=1,RSRC=0,M=0,WAKE=0,ILT=0,PE=0,PT=0 */\r
+ SCI0CR1 = 64; /* Set the SCI configuration */\r
+ /* SCI0SR2: ??=0,??=0,??=0,??=0,??=0,BRK13=0,TXDIR=0,RAF=0 */\r
+ SCI0SR2 = 0; /* Set the Break Character Length and Transmitter pin data direction in Single-wire mode */\r
+ SCI0SR1; /* Reset interrupt request flags */\r
+ /* SCI0CR2: SCTIE=0,TCIE=0,RIE=0,ILIE=0,TE=0,RE=0,RWU=0,SBK=0 */\r
+ SCI0CR2 = 0; /* Disable error interrupts */\r
+ SCI0BD = PrescHigh; /* Set prescaler bits */\r
+ HWEnDi(); /* Enable/disable device according to status flags */\r
+}\r
+\r
+\r
+/* END COM0. */\r
+\r
+\r
+/*\r
+** ###################################################################\r
+**\r
+** This file was created by UNIS Processor Expert 03.33 for \r
+** the Motorola HCS12 series of microcontrollers.\r
+**\r
+** ###################################################################\r
+*/\r