X-Git-Url: https://git.sur5r.net/?p=freertos;a=blobdiff_plain;f=FreeRTOS%2FDemo%2FRX600_RX63N-RSK_Renesas%2FRTOSDemo%2FRenesas-Files%2Fboard%2Frskrx63n%2Fflash_options.c;fp=FreeRTOS%2FDemo%2FRX600_RX63N-RSK_Renesas%2FRTOSDemo%2FRenesas-Files%2Fboard%2Frskrx63n%2Fflash_options.c;h=0000000000000000000000000000000000000000;hp=a6be182d08e4dc4c73237907ea1207195392c9e2;hb=b15dfacb6026af3b0ba697e5753844923b468d2b;hpb=4334233a064299a09d167a497889d3860932a587 diff --git a/FreeRTOS/Demo/RX600_RX63N-RSK_Renesas/RTOSDemo/Renesas-Files/board/rskrx63n/flash_options.c b/FreeRTOS/Demo/RX600_RX63N-RSK_Renesas/RTOSDemo/Renesas-Files/board/rskrx63n/flash_options.c deleted file mode 100644 index a6be182d0..000000000 --- a/FreeRTOS/Demo/RX600_RX63N-RSK_Renesas/RTOSDemo/Renesas-Files/board/rskrx63n/flash_options.c +++ /dev/null @@ -1,124 +0,0 @@ -/*********************************************************************************************************************** -* DISCLAIMER -* This software is supplied by Renesas Electronics Corporation and is only intended for use with Renesas products. No -* other uses are authorized. This software is owned by Renesas Electronics Corporation and is protected under all -* applicable laws, including copyright laws. -* THIS SOFTWARE IS PROVIDED "AS IS" AND RENESAS MAKES NO WARRANTIES REGARDING -* THIS SOFTWARE, WHETHER EXPRESS, IMPLIED OR STATUTORY, INCLUDING BUT NOT LIMITED TO WARRANTIES OF MERCHANTABILITY, -* FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT. ALL SUCH WARRANTIES ARE EXPRESSLY DISCLAIMED. TO THE MAXIMUM -* EXTENT PERMITTED NOT PROHIBITED BY LAW, NEITHER RENESAS ELECTRONICS CORPORATION NOR ANY OF ITS AFFILIATED COMPANIES -* SHALL BE LIABLE FOR ANY DIRECT, INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR ANY REASON RELATED TO THIS -* SOFTWARE, EVEN IF RENESAS OR ITS AFFILIATES HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. -* Renesas reserves the right, without notice, to make changes to this software and to discontinue the availability of -* this software. By using this software, you agree to the additional terms and conditions found by accessing the -* following link: -* http://www.renesas.com/disclaimer -* -* Copyright (C) 2012 Renesas Electronics Corporation. All rights reserved. -***********************************************************************************************************************/ -/*********************************************************************************************************************** -* File Name : flash_options.c -* Device(s) : RX63x -* Description : Some options of the RX63x are set through registers that are found in ROM. These registers and options -* are defined in the 'Option-Setting Memory' section of the HW Manual. These memory locations are defined -* below with descriptions of what is being set. -***********************************************************************************************************************/ -/*********************************************************************************************************************** -* History : DD.MM.YYYY Version Description -* : 31.10.2011 1.00 First Release -* : 13.03.2012 1.10 USER_BOOT_ENABLE macro from r_bsp_config.h is now used to set Option-Setting Memory -* area to boot into User Boot Mode. -***********************************************************************************************************************/ - -/*********************************************************************************************************************** -Includes , "Project Includes" -***********************************************************************************************************************/ -/* Used for fixed-width typedefs. */ -#include -/* Determines whether user boot is used or not. */ -#include "platform.h" - -/* The UB Code A, UB Code B, and Endian select register B (MDEB) are located in the User Boot space. Immediately - following the MDEB register is the User Boot Reset Vector so it is defined below as well. These settings will only - be used when the MCU is reset in User Boot Mode. In order for the MCU to start up in User Boot Mode the following - conditions must be met: - 1) UB code A is 55736572h and 426F6F74h. - 2) UB code B is FFFF FF07h and 0008 C04Ch. - 3) The low level is being input on the MD pin. - 4) The high level is being input on the PC7 pin. - Please see the Option-Setting Memory section of your MCU's HW manual for more information. */ - -/* 0xFF7FFFE8 - 0xFF7FFFEF : UB Code A register - 0xFF7FFFF0 - 0xFF7FFFF7 : UB Code B register - 0xFF7FFFF8 - 0xFF7FFFFB : MDEB register - 0xFF7FFFFC - 0xFF7FFFFF : User Boot Reset Vector */ - -#pragma address user_boot_settings = 0xFF7FFFE8 - -#if USER_BOOT_ENABLE == 1 -extern void PowerON_Reset_PC(void); - -/* Use this array if you are using User Boot. Make sure to fill in valid address for UB Reset Vector. */ -const uint32_t user_boot_settings[6] = -{ - 0x55736572, //Required setting for UB Code A to get into User Boot - 0x426f6f74, //Required setting for UB Code A to get into User Boot - 0xffffff07, //Required setting for UB Code B to get into User Boot - 0x0008c04c, //Required setting for UB Code B to get into User Boot - /* Choose endian for user application code - MDEB Register - Endian Select Register B - b31:b3 Reserved (set to 1) - b2:b0 MDE - Endian Select (0 = Big Endian, 7 = Little Endian) */ - 0xFFFFFFFF, //Select Little Endian for User Boot Code - (uint32_t) PowerON_Reset_PC //This is the User Boot Reset Vector. When using User Boot put in the reset address here -}; -#endif - -/* The Endian select register S (MDES), Option function select register 1 (OFS1), and Option function select register 0 - (OFS0) are located in User ROM. */ - -/* 0xFFFFFF80 - 0xFFFFFF83 : MDES register - 0xFFFFFF84 - 0xFFFFFF87 : Reserved space (0xFF's) - 0xFFFFFF88 - 0xFFFFFF8B : OFS1 register - 0xFFFFFF8C - 0xFFFFFF8F : OFS0 register */ - -#pragma address flash_options = 0xFFFFFF80 - -const uint32_t flash_options[] = -{ - /* Choose endian for user application code - MDES Register - Endian Select Register S - b31:b3 Reserved (set to 1) - b2:b0 MDE - Endian Select (0 = Big Endian, 7 = Little Endian) */ - 0xFFFFFFFF, //Little Endian chosen for User Application - 0xFFFFFFFF, //Reserved space - /* Configure whether voltage detection 0 circuit and HOCO are enabled after reset. - OFS1 - Option Function Select Register 1 - b31:b9 Reserved (set to 1) - b8 HOCOEN - Enable/disable HOCO oscillation after a reset (0=enable, 1=disable) - b7:b3 Reserved (set to 1) - b2 LVDAS - Choose to enable/disable Voltage Detection 0 Circuit after a reset (0=enable, 1=disable) - b1:b0 Reserved (set to 1) */ - 0xFFFFFFFF, //Both are disabled. - /* Configure WDT and IWDT settings. - OFS0 - Option Function Select Register 0 - b31:b29 Reserved (set to 1) - b28 WDTRSTIRQS - WDT Reset Interrupt Request - What to do on underflow (0=take interrupt, 1=reset MCU) - b27:b26 WDTRPSS - WDT Window Start Position Select - (0=25%, 1=50%, 2=75%, 3=100%,don't use) - b25:b24 WDTRPES - WDT Window End Position Select - (0=75%, 1=50%, 2=25%, 3=0%,don't use) - b23:b20 WDTCKS - WDT Clock Frequency Division Ratio - (1=/4, 4=/64, 0xF=/128, 6=/512, 7=/2048, 8=/8192) - b19:b18 WDTTOPS - WDT Timeout Period Select - (0=1024 cycles, 1=4096, 2=8192, 3=16384) - b17 WDTSTRT - WDT Start Mode Select - (0=auto-start after reset, halt after reset) - b16:b15 Reserved (set to 1) - b14 IWDTSLCSTP - IWDT Sleep Mode Count Stop Control - (0=can't stop count, 1=stop w/some low power modes) - b13 Reserved (set to 1) - b12 IWDTRSTIRQS - IWDT Reset Interrupt Request - What to do on underflow (0=take interrupt, 1=reset MCU) - b11:b10 IWDTRPSS - IWDT Window Start Position Select - (0=25%, 1=50%, 2=75%, 3=100%,don't use) - b9:b8 IWDTRPES - IWDT Window End Position Select - (0=75%, 1=50%, 2=25%, 3=0%,don't use) - b7:b4 IWDTCKS - IWDT Clock Frequency Division Ratio - (0=none, 2=/16, 3 = /32, 4=/64, 0xF=/128, 5=/256) - b3:b2 IWDTTOPS - IWDT Timeout Period Select - (0=1024 cycles, 1=4096, 2=8192, 3=16384) - b1 IWDTSTRT - IWDT Start Mode Select - (0=auto-start after reset, halt after reset) - b0 Reserved (set to 1) */ - 0xFFFFFFFF -}; -