i3status(1)
===========
Michael Stapelberg <michael@i3wm.org>
-v2.8, January 2014
+v2.9, March 2015
== NAME
battery 0 {
format = "%status %percentage %remaining %emptytime"
format_down = "No battery"
+ status_chr = "⚇ CHR"
+ status_bat = "⚡ BAT"
+ status_full = "☻ FULL"
path = "/sys/class/power_supply/BAT%d/uevent"
low_threshold = 10
}
Likewise, you can use the +color_separator+ directive to specify the color that
will be used to paint the separator bar. The separator is always output in
-color, even when colors are disabled by the +colors+ directive.
+color, even when colors are disabled by the +colors+ directive. This option has
+no effect when +output_format+ is set to +i3bar+ or +none+.
The +interval+ directive specifies the time in seconds for which i3status will
sleep before printing the next status line.
should only used for such quick glances, because it will only support very
basic output-features (for example you only get 3 bits of color depth).
none::
-Does not use any color codes. Separates values by the pipe symbol. This should
-be used with i3bar and can be used for custom scripts.
+Does not use any color codes. Separates values by the pipe symbol by default.
+This should be used with i3bar and can be used for custom scripts.
It's also possible to use the color_good, color_degraded, color_bad directives
to define specific colors per module. If one of these directives is defined
in a module section its value will override the value defined in the general
section just for this module.
+If you don't fancy the vertical separators between modules i3status/i3bar
+uses by default, you can employ the +separator+ directive to configure how
+modules are separated. You can either disable the default separator altogether
+setting it to the empty string. You might then define separation as part of a
+module's format string. This is your only option when using the i3bar output
+format as the separator is drawn by i3bar directly otherwise. For the other
+output formats, the provided non-empty string will be automatically enclosed
+with the necessary coloring bits if color support is enabled.
+
+*Example configuration*:
+-------------------------------------------------------------
+general {
+ output_format = "xmobar"
+ separator = " "
+}
+
+order += "load"
+order += "disk /"
+
+load {
+ format = "[ load: %1min, %5min, %15min ]"
+}
+disk "/" {
+ format = "%avail"
+}
+-------------------------------------------------------------
+
=== IPv6
This module gets the IPv6 address used for outgoing connections (that is, the
custom::
The custom prefixes (K, M, G, T) represent multiples of powers of 1024.
+It is possible to define a low_threshold that causes the disk text to be
+displayed using color_bad. The low_threshold type can be of threshold_type
+"bytes_free", "bytes_avail", "percentage_free", or "percentage_avail", where
+the former two can be prepended by a generic prefix (k, m, g, t) having
+prefix_type. So, if you configure low_threshold to 2, threshold_type to
+"gbytes_avail", and prefix_type to "binary", and the remaining available disk
+space is below 2 GiB, it will be colored bad. If not specified, threshold_type
+is assumed to be "percentage_avail" and low_threshold to be set to 0, which
+implies no coloring at all.
+
+You can define a different format with the option "format_not_mounted"
+which is used if the path is not a mount point. So you can just empty
+the output for the given path with adding »format_not_mounted=""«
+to the config section.
+
*Example order*: +disk /mnt/usbstick+
*Example format*: +%free (%avail)/ %total+
*Example prefix_type*: +custom+
+*Example low_threshold*: +5+
+
+*Example threshold_type*: +percentage_free+
+
=== Run-watch
Expands the given path to a pidfile and checks if the process ID found inside
=== Wireless
-Gets the link quality and ESSID of the given wireless network interface. You
-can specify different format strings for the network being connected or not
-connected.
+Gets the link quality, frequency and ESSID of the given wireless network
+interface. You can specify different format strings for the network being
+connected or not connected.
+
+The special interface name `_first_` will be replaced by the first wireless
+network interface found on the system (excluding devices starting with "lo").
*Example order*: +wireless wlan0+
-*Example format*: +W: (%quality at %essid, %bitrate) %ip+
+*Example format*: +W: (%quality at %essid, %bitrate / %frequency) %ip+
=== Ethernet
interface. Getting the link speed requires the cap_net_admin capability. Set
it using +setcap cap_net_admin=ep $(which i3status)+.
+The special interface name `_first_` will be replaced by the first non-wireless
+network interface found on the system (excluding devices starting with "lo").
+
*Example order*: +ethernet eth0+
*Example format*: +E: %ip (%speed)+
"percentage". So, if you configure low_threshold to 10 and threshold_type to
"time", and your battery lasts another 9 minutes, it will be colored red.
+Optionally custom strings including any UTF-8 symbols can be used for different
+battery states. This makes it possible to display individual symbols
+for each state (charging, discharging, full)
+Of course it will also work with special iconic fonts, such as FontAwesome.
+If any of this special status strings is omitted, the default (CHR, BAT, FULL)
+is used.
+
*Example order*: +battery 0+
*Example format*: +%status %remaining (%emptytime %consumption)+
*Example format_down*: +No battery+
+*Example status_chr*: +⚇ CHR+
+
+*Example status_bat*: +⚡ BAT+
+
+*Example status_full*: +☻ FULL+
+
*Example low_threshold*: +30+
*Example threshold_type*: +time+
*Example order*: +volume master+
*Example format*: +♪: %volume+
+
*Example format_muted*: +♪: 0%%+
*Example configuration*:
}
-------------------------------------------------------------
+== Universal module options
+
+When using the i3bar output format, there are a few additional options that
+can be used with all modules to customize their appearance:
+
+align::
+ The alignment policy to use when the minimum width (see below) is not
+ reached. Either +center+ (default), +right+ or +left+.
+min_width::
+ The minimum width (in pixels) the module should occupy. If the module takes
+ less space than the specified size, the block will be padded to the left
+ and/or the right side, according to the defined alignment policy. This is
+ useful when you want to prevent the whole status line from shifting when
+ values take more or less space between each iteration.
+ The option can also be a string. In this case, the width of the given text
+ determines the minimum width of the block. This is useful when you want to
+ set a sensible minimum width regardless of which font you are using, and at
+ what particular size. Please note that a number enclosed with quotes will
+ still be treated as a number.
+
+*Example configuration*:
+-------------------------------------------------------------
+disk "/" {
+ format = "%avail"
+ align = "left"
+ min_width = 100
+}
+-------------------------------------------------------------
+
== Using i3status with dzen2
After installing dzen2, you can directly use it with i3status. Just ensure that
projects / i3 / i3status / blobdiff