Merge branch 'master' of git://git.denx.de/u-boot-sunxi
sunxi: Enable eMMC on Libre Computer Board ALL-H3-CC boards The Libretech ALL-H3-CC has a high density connector for attaching an eMMC module. The module form factor and connection is specific to Libretech, and has provisions for split vmmc/vqmmc (core and I/O) voltage supplies, but this board does not wire the vqmmc side. The H2+/H3/H5 SoCs do not support alternate I/O voltages for eMMC either. Only 3.3V is supported. A specific module that ties vqmmc to vmmc, with both at 3.3V, must be used. Given that a) eMMC is not designed to be hotplugged, b) power is always provided on the pins, and c) MMC controllers can deal with missing cards, we can enable this by default. If a module is attached it will be picked up by the system. The device tree change was also submitted to the Linux Kernel and has already been queued up for 4.19. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Acked-by: Maxime Ripard <maxime.ripard@bootlin.com> Reviewed-by: Jagan Teki <jagan@openedev.com>
Merge branch 'master' of git://git.denx.de/u-boot-spi
zynqmp: zcu102: Add qspi driver support for ZynqMP zcu102 boards This patch adds qspi driver support for all ZynqMP ZCU102 boards. Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Acked-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Jagan Teki <jagan@openedev.com>
spi: zynqmp_gqspi: Add support for ZynqMP qspi driver This patch adds qspi driver support for ZynqMP SoC. This driver is responsible for communicating with qspi flash devices. Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> [jagan: removed GQSPI_MIO_NUM_ macros] Reviewed-by: Jagan Teki <jagan@openedev.com>
spi: xilinx_spi: Added support to read JEDEC-id twice at the boot time This patch is for the startup block issue in the spi controller. SPI clock is passing through STARTUP block to FLASH. STARTUP block don't provide clock as soon as QSPI provides command. So, first command fails. This patch added support to read JEDEC id in xilinx_spi_xfer (). Signed-off-by: Vipul Kumar <vipul.kumar@xilinx.com> Reviewed-by: Jagan Teki <jagan@openedev.com>
spi: xilinx_spi: Modify transfer logic xilinx_spi_xfer() function This patch modify xilinx_spi_xfer() function and add rxfifo() and txfifo() functions to add the modularity so that these functions can be used by other functions within the same file. This patch also added support to read fifo_size from dts. Signed-off-by: Vipul Kumar <vipul.kumar@xilinx.com> Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Reviewed-by: Jagan Teki <jagan@openedev.com>
configs: Bananapi_M2_Ultra: enable gigabit ethernet Enable the gigabit ethernet for the Bananapi M2 Ultra board. Tested on BananaPi M2 Berry (R40), custom board (V40) Reviewed-by: Joe Hershberger <joe.hershberger@ni.com> Signed-off-by: Lothar Felten <lothar.felten@gmail.com> Acked-by: Maxime Ripard <maxime.ripard@bootlin.com> Reviewed-by: Jagan Teki <jagan@openedev.com> Tested-by: Jagan Teki <jagan@openedev.com>
sunxi: R40: add gigabit ethernet devicetree node Add a device tree node for the Allwinner R40/V40 GMAC gigabit ethernet interface. The R40 SoC does not use the syscon register for GMAC settings. The gigabit ethernet interface can only be routed to a fixed set of pins. Updated to match the Linux kernel's device tree. Signed-off-by: Lothar Felten <lothar.felten@gmail.com> Acked-by: Maxime Ripard <maxime.ripard@bootlin.com> Reviewed-by: Jagan Teki <jagan@openedev.com> Tested-by: Jagan Teki <jagan@openedev.com>
net: sun8i-emac: support R40 GMAC Add support for the GMAC found in the Allwinner R40/V40 SoC. The R40 GMAC interface is not controlled by the syscon register but has a separate configuration register in the CCU. The clock gate and reset bits are in a different register compared to the other SoCs supported by this driver. The driver uses the -gmac suffix for the R40 because the R40 also has a different 100 MBit MAC (EMAC). Signed-off-by: Lothar Felten <lothar.felten@gmail.com> Reviewed-by: Jagan Teki <jagan@openedev.com> Tested-by: Jagan Teki <jagan@openedev.com>
net: sun8i-emac: set mux and clock by driver data Use driver data->variant information to select device specific pin mux and phy clock settings. Suggested by Jagan Teki Reviewed-by: Jagan Teki <jagan@openedev.com> Tested-by: Jagan Teki <jagan@openedev.com> Signed-off-by: Lothar Felten <lothar.felten@gmail.com>
net: sun8i-emac: fix printing NULL character If the variant is not set and therefore NULL, do not attempt to print the variant. Signed-off-by: Lothar Felten <lothar.felten@gmail.com> Acked-by: Maxime Ripard <maxime.ripard@bootlin.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Jagan Teki <jagan@openedev.com> Tested-by: Jagan Teki <jagan@openedev.com>
sunxi: R40: add gigabit ethernet clocks Add clock control entries for the gigabit interface of the Allwinner R40/V40 CPU Acked-by: Maxime Ripard <maxime.ripard@bootlin.com> Reviewed-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Jagan Teki <jagan@openedev.com> Tested-by: Jagan Teki <jagan@openedev.com> Signed-off-by: Lothar Felten <lothar.felten@gmail.com>
dm: sunxi: Use DM for MMC and SATA on all A10 boards Use the driver model for MMC and SATA, in preparation for CONFIG_BLK defaulting to y. Tested on A10 Cubieboard. Signed-off-by: Adam Sampson <ats@offog.org> Acked-by: Maxime Ripard <maxime.ripard@bootlin.com> Reviewed-by: Jagan Teki <jteki@openedev.com>