From: Stefan Roese <sr@denx.de>
Date: Tue, 18 Jul 2017 12:10:49 +0000 (+0200)
Subject: x86: dfi-bt700: Add xHCI USB support
X-Git-Tag: v2017.09-rc1~23
X-Git-Url: https://git.sur5r.net/?p=u-boot;a=commitdiff_plain;h=1f4e25780a827de9526b5f60b8a574b1e4f45b9c

x86: dfi-bt700: Add xHCI USB support

Change from EHCI to xHCI on the DFI BayTrail SoM.

The xHCI USB hub is connected to an GPIO on the DFI BayTrail SoM. For
correct operation, it needs to get reset upon power-up. Otherwise it
may happen that the hub is not detected after a software reboot. This
patch also configures this GPIO in the dts for correct operation.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
---

diff --git a/arch/x86/dts/dfi-bt700.dtsi b/arch/x86/dts/dfi-bt700.dtsi
index 04aa95ad52..b62e00ff1f 100644
--- a/arch/x86/dts/dfi-bt700.dtsi
+++ b/arch/x86/dts/dfi-bt700.dtsi
@@ -47,6 +47,15 @@
 			pad-offset = <0x3a0>;
 			mode-func = <1>;
 		};
+
+		xhci_hub_reset: usb_ulpi_stp@0 {
+			gpio-offset = <0xa0 10>;
+			pad-offset = <0x23b0>;
+			mode-func = <0>;
+			mode-gpio;
+			output-value = <1>;
+			direction = <PIN_OUTPUT>;
+		};
 	};
 
 	chosen {
@@ -261,6 +270,9 @@
 		fsp,enable-spi;
 		fsp,enable-sata;
 		fsp,sata-mode = <SATA_MODE_AHCI>;
+#ifdef CONFIG_USB_XHCI_HCD
+		fsp,enable-xhci;
+#endif
 		fsp,lpe-mode = <LPE_MODE_PCI>;
 		fsp,lpss-sio-mode = <LPSS_SIO_MODE_PCI>;
 		fsp,enable-dma0;
diff --git a/board/dfi/dfi-bt700/Kconfig b/board/dfi/dfi-bt700/Kconfig
index 3f0acb39f7..fca8b53d02 100644
--- a/board/dfi/dfi-bt700/Kconfig
+++ b/board/dfi/dfi-bt700/Kconfig
@@ -21,6 +21,7 @@ config BOARD_SPECIFIC_OPTIONS # dummy
 	select X86_RESET_VECTOR if !EFI_STUB
 	select INTEL_BAYTRAIL
 	select BOARD_ROMSIZE_KB_8192
+	select BOARD_LATE_INIT
 
 config PCIE_ECAM_BASE
 	default 0xe0000000
diff --git a/board/dfi/dfi-bt700/dfi-bt700.c b/board/dfi/dfi-bt700/dfi-bt700.c
index 8645bdc795..3dd2036d11 100644
--- a/board/dfi/dfi-bt700/dfi-bt700.c
+++ b/board/dfi/dfi-bt700/dfi-bt700.c
@@ -28,3 +28,30 @@ int board_early_init_f(void)
 
 	return 0;
 }
+
+int board_late_init(void)
+{
+	struct gpio_desc desc;
+	int ret;
+
+	ret = dm_gpio_lookup_name("F10", &desc);
+	if (ret)
+		debug("gpio ret=%d\n", ret);
+	ret = dm_gpio_request(&desc, "xhci_hub_reset");
+	if (ret)
+		debug("gpio_request ret=%d\n", ret);
+	ret = dm_gpio_set_dir_flags(&desc, GPIOD_IS_OUT);
+	if (ret)
+		debug("gpio dir ret=%d\n", ret);
+
+	/* Pull xHCI hub reset to low (active low) */
+	dm_gpio_set_value(&desc, 0);
+
+	/* Wait at least 5 ms, so lets choose 10 to be safe */
+	mdelay(10);
+
+	/* Pull xHCI hub reset to high (active low) */
+	dm_gpio_set_value(&desc, 1);
+
+	return 0;
+}