2 # (C) Copyright 2000 - 2008
3 # Wolfgang Denk, DENX Software Engineering, wd@denx.de.
5 # See file CREDITS for list of people who contributed to this
8 # This program is free software; you can redistribute it and/or
9 # modify it under the terms of the GNU General Public License as
10 # published by the Free Software Foundation; either version 2 of
11 # the License, or (at your option) any later version.
13 # This program is distributed in the hope that it will be useful,
14 # but WITHOUT ANY WARRANTY; without even the implied warranty of
15 # MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
16 # GNU General Public License for more details.
18 # You should have received a copy of the GNU General Public License
19 # along with this program; if not, write to the Free Software
20 # Foundation, Inc., 59 Temple Place, Suite 330, Boston,
27 This directory contains the source code for U-Boot, a boot loader for
28 Embedded boards based on PowerPC, ARM, MIPS and several other
29 processors, which can be installed in a boot ROM and used to
30 initialize and test the hardware or to download and run application
33 The development of U-Boot is closely related to Linux: some parts of
34 the source code originate in the Linux source tree, we have some
35 header files in common, and special provision has been made to
36 support booting of Linux images.
38 Some attention has been paid to make this software easily
39 configurable and extendable. For instance, all monitor commands are
40 implemented with the same call interface, so that it's very easy to
41 add new commands. Also, instead of permanently adding rarely used
42 code (for instance hardware test utilities) to the monitor, you can
43 load and run it dynamically.
49 In general, all boards for which a configuration option exists in the
50 Makefile have been tested to some extent and can be considered
51 "working". In fact, many of them are used in production systems.
53 In case of problems see the CHANGELOG and CREDITS files to find out
54 who contributed the specific port. The MAINTAINERS file lists board
61 In case you have questions about, problems with or contributions for
62 U-Boot you should send a message to the U-Boot mailing list at
63 <u-boot-users@lists.sourceforge.net>. There is also an archive of
64 previous traffic on the mailing list - please search the archive
65 before asking FAQ's. Please see
66 http://lists.sourceforge.net/lists/listinfo/u-boot-users/
69 Where to get source code:
70 =========================
72 The U-Boot source code is maintained in the git repository at
73 git://www.denx.de/git/u-boot.git ; you can browse it online at
74 http://www.denx.de/cgi-bin/gitweb.cgi?p=u-boot.git;a=summary
76 The "snapshot" links on this page allow you to download tarballs of
77 any version you might be interested in. Ofifcial releases are also
78 available for FTP download from the ftp://ftp.denx.de/pub/u-boot/
81 Pre-built (and tested) images are available from
82 ftp://ftp.denx.de/pub/u-boot/images/
88 - start from 8xxrom sources
89 - create PPCBoot project (http://sourceforge.net/projects/ppcboot)
91 - make it easier to add custom boards
92 - make it possible to add other [PowerPC] CPUs
93 - extend functions, especially:
94 * Provide extended interface to Linux boot loader
97 * PCMCIA / CompactFLash / ATA disk / SCSI ... boot
98 - create ARMBoot project (http://sourceforge.net/projects/armboot)
99 - add other CPU families (starting with ARM)
100 - create U-Boot project (http://sourceforge.net/projects/u-boot)
101 - current project page: see http://www.denx.de/wiki/UBoot
107 The "official" name of this project is "Das U-Boot". The spelling
108 "U-Boot" shall be used in all written text (documentation, comments
109 in source files etc.). Example:
111 This is the README file for the U-Boot project.
113 File names etc. shall be based on the string "u-boot". Examples:
115 include/asm-ppc/u-boot.h
117 #include <asm/u-boot.h>
119 Variable names, preprocessor constants etc. shall be either based on
120 the string "u_boot" or on "U_BOOT". Example:
122 U_BOOT_VERSION u_boot_logo
123 IH_OS_U_BOOT u_boot_hush_start
129 U-Boot uses a 3 level version number containing a version, a
130 sub-version, and a patchlevel: "U-Boot-2.34.5" means version "2",
131 sub-version "34", and patchlevel "4".
133 The patchlevel is used to indicate certain stages of development
134 between released versions, i. e. officially released versions of
135 U-Boot will always have a patchlevel of "0".
141 - board Board dependent files
142 - common Misc architecture independent functions
143 - cpu CPU specific files
144 - 74xx_7xx Files specific to Freescale MPC74xx and 7xx CPUs
145 - arm720t Files specific to ARM 720 CPUs
146 - arm920t Files specific to ARM 920 CPUs
147 - at91rm9200 Files specific to Atmel AT91RM9200 CPU
148 - imx Files specific to Freescale MC9328 i.MX CPUs
149 - s3c24x0 Files specific to Samsung S3C24X0 CPUs
150 - arm925t Files specific to ARM 925 CPUs
151 - arm926ejs Files specific to ARM 926 CPUs
152 - arm1136 Files specific to ARM 1136 CPUs
153 - at32ap Files specific to Atmel AVR32 AP CPUs
154 - i386 Files specific to i386 CPUs
155 - ixp Files specific to Intel XScale IXP CPUs
156 - mcf52x2 Files specific to Freescale ColdFire MCF52x2 CPUs
157 - mcf5227x Files specific to Freescale ColdFire MCF5227x CPUs
158 - mcf532x Files specific to Freescale ColdFire MCF5329 CPUs
159 - mcf5445x Files specific to Freescale ColdFire MCF5445x CPUs
160 - mcf547x_8x Files specific to Freescale ColdFire MCF547x_8x CPUs
161 - mips Files specific to MIPS CPUs
162 - mpc5xx Files specific to Freescale MPC5xx CPUs
163 - mpc5xxx Files specific to Freescale MPC5xxx CPUs
164 - mpc8xx Files specific to Freescale MPC8xx CPUs
165 - mpc8220 Files specific to Freescale MPC8220 CPUs
166 - mpc824x Files specific to Freescale MPC824x CPUs
167 - mpc8260 Files specific to Freescale MPC8260 CPUs
168 - mpc85xx Files specific to Freescale MPC85xx CPUs
169 - nios Files specific to Altera NIOS CPUs
170 - nios2 Files specific to Altera Nios-II CPUs
171 - ppc4xx Files specific to AMCC PowerPC 4xx CPUs
172 - pxa Files specific to Intel XScale PXA CPUs
173 - s3c44b0 Files specific to Samsung S3C44B0 CPUs
174 - sa1100 Files specific to Intel StrongARM SA1100 CPUs
175 - disk Code for disk drive partition handling
176 - doc Documentation (don't expect too much)
177 - drivers Commonly used device drivers
178 - dtt Digital Thermometer and Thermostat drivers
179 - examples Example code for standalone applications, etc.
180 - include Header Files
181 - lib_arm Files generic to ARM architecture
182 - lib_avr32 Files generic to AVR32 architecture
183 - lib_generic Files generic to all architectures
184 - lib_i386 Files generic to i386 architecture
185 - lib_m68k Files generic to m68k architecture
186 - lib_mips Files generic to MIPS architecture
187 - lib_nios Files generic to NIOS architecture
188 - lib_ppc Files generic to PowerPC architecture
189 - libfdt Library files to support flattened device trees
190 - net Networking code
191 - post Power On Self Test
192 - rtc Real Time Clock drivers
193 - tools Tools to build S-Record or U-Boot images, etc.
195 Software Configuration:
196 =======================
198 Configuration is usually done using C preprocessor defines; the
199 rationale behind that is to avoid dead code whenever possible.
201 There are two classes of configuration variables:
203 * Configuration _OPTIONS_:
204 These are selectable by the user and have names beginning with
207 * Configuration _SETTINGS_:
208 These depend on the hardware etc. and should not be meddled with if
209 you don't know what you're doing; they have names beginning with
212 Later we will add a configuration tool - probably similar to or even
213 identical to what's used for the Linux kernel. Right now, we have to
214 do the configuration by hand, which means creating some symbolic
215 links and editing some configuration files. We use the TQM8xxL boards
219 Selection of Processor Architecture and Board Type:
220 ---------------------------------------------------
222 For all supported boards there are ready-to-use default
223 configurations available; just type "make <board_name>_config".
225 Example: For a TQM823L module type:
230 For the Cogent platform, you need to specify the cpu type as well;
231 e.g. "make cogent_mpc8xx_config". And also configure the cogent
232 directory according to the instructions in cogent/README.
235 Configuration Options:
236 ----------------------
238 Configuration depends on the combination of board and CPU type; all
239 such information is kept in a configuration file
240 "include/configs/<board_name>.h".
242 Example: For a TQM823L module, all configuration settings are in
243 "include/configs/TQM823L.h".
246 Many of the options are named exactly as the corresponding Linux
247 kernel configuration options. The intention is to make it easier to
248 build a config tool - later.
251 The following options need to be configured:
253 - CPU Type: Define exactly one, e.g. CONFIG_MPC85XX.
255 - Board Type: Define exactly one, e.g. CONFIG_MPC8540ADS.
257 - CPU Daughterboard Type: (if CONFIG_ATSTK1000 is defined)
258 Define exactly one, e.g. CONFIG_ATSTK1002
260 - CPU Module Type: (if CONFIG_COGENT is defined)
261 Define exactly one of
263 --- FIXME --- not tested yet:
264 CONFIG_CMA286_60, CONFIG_CMA286_21, CONFIG_CMA286_60P,
265 CONFIG_CMA287_23, CONFIG_CMA287_50
267 - Motherboard Type: (if CONFIG_COGENT is defined)
268 Define exactly one of
269 CONFIG_CMA101, CONFIG_CMA102
271 - Motherboard I/O Modules: (if CONFIG_COGENT is defined)
272 Define one or more of
275 - Motherboard Options: (if CONFIG_CMA101 or CONFIG_CMA102 are defined)
276 Define one or more of
277 CONFIG_LCD_HEARTBEAT - update a character position on
278 the lcd display every second with
281 - Board flavour: (if CONFIG_MPC8260ADS is defined)
284 CFG_8260ADS - original MPC8260ADS
285 CFG_8266ADS - MPC8266ADS
286 CFG_PQ2FADS - PQ2FADS-ZU or PQ2FADS-VR
287 CFG_8272ADS - MPC8272ADS
289 - MPC824X Family Member (if CONFIG_MPC824X is defined)
290 Define exactly one of
291 CONFIG_MPC8240, CONFIG_MPC8245
293 - 8xx CPU Options: (if using an MPC8xx cpu)
294 CONFIG_8xx_GCLK_FREQ - deprecated: CPU clock if
295 get_gclk_freq() cannot work
296 e.g. if there is no 32KHz
297 reference PIT/RTC clock
298 CONFIG_8xx_OSCLK - PLL input clock (either EXTCLK
301 - 859/866/885 CPU options: (if using a MPC859 or MPC866 or MPC885 CPU):
304 CONFIG_8xx_CPUCLK_DEFAULT
305 See doc/README.MPC866
309 Define this to measure the actual CPU clock instead
310 of relying on the correctness of the configured
311 values. Mostly useful for board bringup to make sure
312 the PLL is locked at the intended frequency. Note
313 that this requires a (stable) reference clock (32 kHz
314 RTC clock or CFG_8XX_XIN)
316 - Intel Monahans options:
317 CFG_MONAHANS_RUN_MODE_OSC_RATIO
319 Defines the Monahans run mode to oscillator
320 ratio. Valid values are 8, 16, 24, 31. The core
321 frequency is this value multiplied by 13 MHz.
323 CFG_MONAHANS_TURBO_RUN_MODE_RATIO
325 Defines the Monahans turbo mode to oscillator
326 ratio. Valid values are 1 (default if undefined) and
327 2. The core frequency as calculated above is multiplied
330 - Linux Kernel Interface:
333 U-Boot stores all clock information in Hz
334 internally. For binary compatibility with older Linux
335 kernels (which expect the clocks passed in the
336 bd_info data to be in MHz) the environment variable
337 "clocks_in_mhz" can be defined so that U-Boot
338 converts clock data to MHZ before passing it to the
340 When CONFIG_CLOCKS_IN_MHZ is defined, a definition of
341 "clocks_in_mhz=1" is automatically included in the
344 CONFIG_MEMSIZE_IN_BYTES [relevant for MIPS only]
346 When transfering memsize parameter to linux, some versions
347 expect it to be in bytes, others in MB.
348 Define CONFIG_MEMSIZE_IN_BYTES to make it in bytes.
350 CONFIG_OF_LIBFDT / CONFIG_OF_FLAT_TREE
352 New kernel versions are expecting firmware settings to be
353 passed using flattened device trees (based on open firmware
357 * New libfdt-based support
358 * Adds the "fdt" command
359 * The bootm command automatically updates the fdt
362 * Deprecated, see CONFIG_OF_LIBFDT
363 * Original ft_build.c-based support
364 * Automatically modifies the dft as part of the bootm command
365 * The environment variable "disable_of", when set,
366 disables this functionality.
368 OF_CPU - The proper name of the cpus node.
369 OF_SOC - The proper name of the soc node.
370 OF_TBCLK - The timebase frequency.
371 OF_STDOUT_PATH - The path to the console device
373 boards with QUICC Engines require OF_QE to set UCC mac addresses
377 * CONFIG_OF_LIBFDT - enables the "fdt bd_t" command
378 * CONFIG_OF_FLAT_TREE - The resulting flat device tree
379 will have a copy of the bd_t. Space should be
380 pre-allocated in the dts for the bd_t.
382 CONFIG_OF_HAS_UBOOT_ENV
384 * CONFIG_OF_LIBFDT - enables the "fdt env" command
385 * CONFIG_OF_FLAT_TREE - The resulting flat device tree
386 will have a copy of u-boot's environment variables
388 CONFIG_OF_BOARD_SETUP
390 Board code has addition modification that it wants to make
391 to the flat device tree before handing it off to the kernel
395 This define fills in the correct boot cpu in the boot
396 param header, the default value is zero if undefined.
401 Define this if you want support for Amba PrimeCell PL010 UARTs.
405 Define this if you want support for Amba PrimeCell PL011 UARTs.
409 If you have Amba PrimeCell PL011 UARTs, set this variable to
410 the clock speed of the UARTs.
414 If you have Amba PrimeCell PL010 or PL011 UARTs on your board,
415 define this to a list of base addresses for each (supported)
416 port. See e.g. include/configs/versatile.h
420 Depending on board, define exactly one serial port
421 (like CONFIG_8xx_CONS_SMC1, CONFIG_8xx_CONS_SMC2,
422 CONFIG_8xx_CONS_SCC1, ...), or switch off the serial
423 console by defining CONFIG_8xx_CONS_NONE
425 Note: if CONFIG_8xx_CONS_NONE is defined, the serial
426 port routines must be defined elsewhere
427 (i.e. serial_init(), serial_getc(), ...)
430 Enables console device for a color framebuffer. Needs following
431 defines (cf. smiLynxEM, i8042, board/eltec/bab7xx)
432 VIDEO_FB_LITTLE_ENDIAN graphic memory organisation
434 VIDEO_HW_RECTFILL graphic chip supports
437 VIDEO_HW_BITBLT graphic chip supports
438 bit-blit (cf. smiLynxEM)
439 VIDEO_VISIBLE_COLS visible pixel columns
441 VIDEO_VISIBLE_ROWS visible pixel rows
442 VIDEO_PIXEL_SIZE bytes per pixel
443 VIDEO_DATA_FORMAT graphic data format
444 (0-5, cf. cfb_console.c)
445 VIDEO_FB_ADRS framebuffer address
446 VIDEO_KBD_INIT_FCT keyboard int fct
447 (i.e. i8042_kbd_init())
448 VIDEO_TSTC_FCT test char fct
450 VIDEO_GETC_FCT get char fct
452 CONFIG_CONSOLE_CURSOR cursor drawing on/off
453 (requires blink timer
455 CFG_CONSOLE_BLINK_COUNT blink interval (cf. i8042.c)
456 CONFIG_CONSOLE_TIME display time/date info in
458 (requires CONFIG_CMD_DATE)
459 CONFIG_VIDEO_LOGO display Linux logo in
461 CONFIG_VIDEO_BMP_LOGO use bmp_logo.h instead of
462 linux_logo.h for logo.
463 Requires CONFIG_VIDEO_LOGO
464 CONFIG_CONSOLE_EXTRA_INFO
465 addional board info beside
468 When CONFIG_CFB_CONSOLE is defined, video console is
469 default i/o. Serial console can be forced with
470 environment 'console=serial'.
472 When CONFIG_SILENT_CONSOLE is defined, all console
473 messages (by U-Boot and Linux!) can be silenced with
474 the "silent" environment variable. See
475 doc/README.silent for more information.
478 CONFIG_BAUDRATE - in bps
479 Select one of the baudrates listed in
480 CFG_BAUDRATE_TABLE, see below.
481 CFG_BRGCLK_PRESCALE, baudrate prescale
483 - Interrupt driven serial port input:
484 CONFIG_SERIAL_SOFTWARE_FIFO
487 Use an interrupt handler for receiving data on the
488 serial port. It also enables using hardware handshake
489 (RTS/CTS) and UART's built-in FIFO. Set the number of
490 bytes the interrupt driven input buffer should have.
492 Leave undefined to disable this feature, including
493 disable the buffer and hardware handshake.
495 - Console UART Number:
499 If defined internal UART1 (and not UART0) is used
500 as default U-Boot console.
502 - Boot Delay: CONFIG_BOOTDELAY - in seconds
503 Delay before automatically booting the default image;
504 set to -1 to disable autoboot.
506 See doc/README.autoboot for these options that
507 work with CONFIG_BOOTDELAY. None are required.
508 CONFIG_BOOT_RETRY_TIME
509 CONFIG_BOOT_RETRY_MIN
510 CONFIG_AUTOBOOT_KEYED
511 CONFIG_AUTOBOOT_PROMPT
512 CONFIG_AUTOBOOT_DELAY_STR
513 CONFIG_AUTOBOOT_STOP_STR
514 CONFIG_AUTOBOOT_DELAY_STR2
515 CONFIG_AUTOBOOT_STOP_STR2
516 CONFIG_ZERO_BOOTDELAY_CHECK
517 CONFIG_RESET_TO_RETRY
521 Only needed when CONFIG_BOOTDELAY is enabled;
522 define a command string that is automatically executed
523 when no character is read on the console interface
524 within "Boot Delay" after reset.
527 This can be used to pass arguments to the bootm
528 command. The value of CONFIG_BOOTARGS goes into the
529 environment value "bootargs".
531 CONFIG_RAMBOOT and CONFIG_NFSBOOT
532 The value of these goes into the environment as
533 "ramboot" and "nfsboot" respectively, and can be used
534 as a convenience, when switching between booting from
540 When this option is #defined, the existence of the
541 environment variable "preboot" will be checked
542 immediately before starting the CONFIG_BOOTDELAY
543 countdown and/or running the auto-boot command resp.
544 entering interactive mode.
546 This feature is especially useful when "preboot" is
547 automatically generated or modified. For an example
548 see the LWMON board specific code: here "preboot" is
549 modified when the user holds down a certain
550 combination of keys on the (special) keyboard when
553 - Serial Download Echo Mode:
555 If defined to 1, all characters received during a
556 serial download (using the "loads" command) are
557 echoed back. This might be needed by some terminal
558 emulations (like "cu"), but may as well just take
559 time on others. This setting #define's the initial
560 value of the "loads_echo" environment variable.
562 - Kgdb Serial Baudrate: (if CONFIG_CMD_KGDB is defined)
564 Select one of the baudrates listed in
565 CFG_BAUDRATE_TABLE, see below.
568 Monitor commands can be included or excluded
569 from the build by using the #include files
570 "config_cmd_all.h" and #undef'ing unwanted
571 commands, or using "config_cmd_default.h"
572 and augmenting with additional #define's
575 The default command configuration includes all commands
576 except those marked below with a "*".
578 CONFIG_CMD_ASKENV * ask for env variable
579 CONFIG_CMD_AUTOSCRIPT Autoscript Support
580 CONFIG_CMD_BDI bdinfo
581 CONFIG_CMD_BEDBUG * Include BedBug Debugger
582 CONFIG_CMD_BMP * BMP support
583 CONFIG_CMD_BSP * Board specific commands
584 CONFIG_CMD_BOOTD bootd
585 CONFIG_CMD_CACHE * icache, dcache
586 CONFIG_CMD_CONSOLE coninfo
587 CONFIG_CMD_DATE * support for RTC, date/time...
588 CONFIG_CMD_DHCP * DHCP support
589 CONFIG_CMD_DIAG * Diagnostics
590 CONFIG_CMD_DOC * Disk-On-Chip Support
591 CONFIG_CMD_DTT * Digital Therm and Thermostat
592 CONFIG_CMD_ECHO echo arguments
593 CONFIG_CMD_EEPROM * EEPROM read/write support
594 CONFIG_CMD_ELF * bootelf, bootvx
595 CONFIG_CMD_ENV saveenv
596 CONFIG_CMD_FDC * Floppy Disk Support
597 CONFIG_CMD_FAT * FAT partition support
598 CONFIG_CMD_FDOS * Dos diskette Support
599 CONFIG_CMD_FLASH flinfo, erase, protect
600 CONFIG_CMD_FPGA FPGA device initialization support
601 CONFIG_CMD_HWFLOW * RTS/CTS hw flow control
602 CONFIG_CMD_I2C * I2C serial bus support
603 CONFIG_CMD_IDE * IDE harddisk support
604 CONFIG_CMD_IMI iminfo
605 CONFIG_CMD_IMLS List all found images
606 CONFIG_CMD_IMMAP * IMMR dump support
607 CONFIG_CMD_IRQ * irqinfo
608 CONFIG_CMD_ITEST Integer/string test of 2 values
609 CONFIG_CMD_JFFS2 * JFFS2 Support
610 CONFIG_CMD_KGDB * kgdb
611 CONFIG_CMD_LOADB loadb
612 CONFIG_CMD_LOADS loads
613 CONFIG_CMD_MEMORY md, mm, nm, mw, cp, cmp, crc, base,
615 CONFIG_CMD_MISC Misc functions like sleep etc
616 CONFIG_CMD_MMC * MMC memory mapped support
617 CONFIG_CMD_MII * MII utility commands
618 CONFIG_CMD_NAND * NAND support
619 CONFIG_CMD_NET bootp, tftpboot, rarpboot
620 CONFIG_CMD_PCI * pciinfo
621 CONFIG_CMD_PCMCIA * PCMCIA support
622 CONFIG_CMD_PING * send ICMP ECHO_REQUEST to network
624 CONFIG_CMD_PORTIO * Port I/O
625 CONFIG_CMD_REGINFO * Register dump
626 CONFIG_CMD_RUN run command in env variable
627 CONFIG_CMD_SAVES * save S record dump
628 CONFIG_CMD_SCSI * SCSI Support
629 CONFIG_CMD_SDRAM * print SDRAM configuration information
630 (requires CONFIG_CMD_I2C)
631 CONFIG_CMD_SETGETDCR Support for DCR Register access
633 CONFIG_CMD_SPI * SPI serial bus support
634 CONFIG_CMD_USB * USB support
635 CONFIG_CMD_VFD * VFD support (TRAB)
636 CONFIG_CMD_BSP * Board SPecific functions
637 CONFIG_CMD_CDP * Cisco Discover Protocol support
638 CONFIG_CMD_FSL * Microblaze FSL support
641 EXAMPLE: If you want all functions except of network
642 support you can write:
644 #include "config_cmd_all.h"
645 #undef CONFIG_CMD_NET
648 fdt (flattened device tree) command: CONFIG_OF_LIBFDT
650 Note: Don't enable the "icache" and "dcache" commands
651 (configuration option CONFIG_CMD_CACHE) unless you know
652 what you (and your U-Boot users) are doing. Data
653 cache cannot be enabled on systems like the 8xx or
654 8260 (where accesses to the IMMR region must be
655 uncached), and it cannot be disabled on all other
656 systems where we (mis-) use the data cache to hold an
657 initial stack and some data.
660 XXX - this list needs to get updated!
664 If this variable is defined, it enables watchdog
665 support. There must be support in the platform specific
666 code for a watchdog. For the 8xx and 8260 CPUs, the
667 SIU Watchdog feature is enabled in the SYPCR
671 CONFIG_VERSION_VARIABLE
672 If this variable is defined, an environment variable
673 named "ver" is created by U-Boot showing the U-Boot
674 version as printed by the "version" command.
675 This variable is readonly.
679 When CONFIG_CMD_DATE is selected, the type of the RTC
680 has to be selected, too. Define exactly one of the
683 CONFIG_RTC_MPC8xx - use internal RTC of MPC8xx
684 CONFIG_RTC_PCF8563 - use Philips PCF8563 RTC
685 CONFIG_RTC_MC146818 - use MC146818 RTC
686 CONFIG_RTC_DS1307 - use Maxim, Inc. DS1307 RTC
687 CONFIG_RTC_DS1337 - use Maxim, Inc. DS1337 RTC
688 CONFIG_RTC_DS1338 - use Maxim, Inc. DS1338 RTC
689 CONFIG_RTC_DS164x - use Dallas DS164x RTC
690 CONFIG_RTC_ISL1208 - use Intersil ISL1208 RTC
691 CONFIG_RTC_MAX6900 - use Maxim, Inc. MAX6900 RTC
692 CFG_RTC_DS1337_NOOSC - Turn off the OSC output for DS1337
694 Note that if the RTC uses I2C, then the I2C interface
695 must also be configured. See I2C Support, below.
699 When CONFIG_TIMESTAMP is selected, the timestamp
700 (date and time) of an image is printed by image
701 commands like bootm or iminfo. This option is
702 automatically enabled when you select CONFIG_CMD_DATE .
705 CONFIG_MAC_PARTITION and/or CONFIG_DOS_PARTITION
706 and/or CONFIG_ISO_PARTITION
708 If IDE or SCSI support is enabled (CONFIG_CMD_IDE or
709 CONFIG_CMD_SCSI) you must configure support for at
710 least one partition type as well.
713 CONFIG_IDE_RESET_ROUTINE - this is defined in several
714 board configurations files but used nowhere!
716 CONFIG_IDE_RESET - is this is defined, IDE Reset will
717 be performed by calling the function
718 ide_set_reset(int reset)
719 which has to be defined in a board specific file
724 Set this to enable ATAPI support.
729 Set this to enable support for disks larger than 137GB
730 Also look at CFG_64BIT_LBA ,CFG_64BIT_VSPRINTF and CFG_64BIT_STRTOUL
731 Whithout these , LBA48 support uses 32bit variables and will 'only'
732 support disks up to 2.1TB.
735 When enabled, makes the IDE subsystem use 64bit sector addresses.
739 At the moment only there is only support for the
740 SYM53C8XX SCSI controller; define
741 CONFIG_SCSI_SYM53C8XX to enable it.
743 CFG_SCSI_MAX_LUN [8], CFG_SCSI_MAX_SCSI_ID [7] and
744 CFG_SCSI_MAX_DEVICE [CFG_SCSI_MAX_SCSI_ID *
745 CFG_SCSI_MAX_LUN] can be adjusted to define the
746 maximum numbers of LUNs, SCSI ID's and target
748 CFG_SCSI_SYM53C8XX_CCF to fix clock timing (80Mhz)
750 - NETWORK Support (PCI):
752 Support for Intel 8254x gigabit chips.
755 Support for Intel 82557/82559/82559ER chips.
756 Optional CONFIG_EEPRO100_SROM_WRITE enables eeprom
757 write routine for first time initialisation.
760 Support for Digital 2114x chips.
761 Optional CONFIG_TULIP_SELECT_MEDIA for board specific
762 modem chip initialisation (KS8761/QS6611).
765 Support for National dp83815 chips.
768 Support for National dp8382[01] gigabit chips.
770 - NETWORK Support (other):
772 CONFIG_DRIVER_LAN91C96
773 Support for SMSC's LAN91C96 chips.
776 Define this to hold the physical address
777 of the LAN91C96's I/O space
779 CONFIG_LAN91C96_USE_32_BIT
780 Define this to enable 32 bit addressing
782 CONFIG_DRIVER_SMC91111
783 Support for SMSC's LAN91C111 chip
786 Define this to hold the physical address
787 of the device (I/O space)
789 CONFIG_SMC_USE_32_BIT
790 Define this if data bus is 32 bits
792 CONFIG_SMC_USE_IOFUNCS
793 Define this to use i/o functions instead of macros
794 (some hardware wont work with macros)
797 At the moment only the UHCI host controller is
798 supported (PIP405, MIP405, MPC5200); define
799 CONFIG_USB_UHCI to enable it.
800 define CONFIG_USB_KEYBOARD to enable the USB Keyboard
801 and define CONFIG_USB_STORAGE to enable the USB
804 Supported are USB Keyboards and USB Floppy drives
806 MPC5200 USB requires additional defines:
808 for 528 MHz Clock: 0x0001bbbb
810 for differential drivers: 0x00001000
811 for single ended drivers: 0x00005000
813 May be defined to allow interrupt polling
814 instead of using asynchronous interrupts
817 Define the below if you wish to use the USB console.
818 Once firmware is rebuilt from a serial console issue the
819 command "setenv stdin usbtty; setenv stdout usbtty" and
820 attach your usb cable. The Unix command "dmesg" should print
821 it has found a new device. The environment variable usbtty
822 can be set to gserial or cdc_acm to enable your device to
823 appear to a USB host as a Linux gserial device or a
824 Common Device Class Abstract Control Model serial device.
825 If you select usbtty = gserial you should be able to enumerate
827 # modprobe usbserial vendor=0xVendorID product=0xProductID
828 else if using cdc_acm, simply setting the environment
829 variable usbtty to be cdc_acm should suffice. The following
830 might be defined in YourBoardName.h
833 Define this to build a UDC device
836 Define this to have a tty type of device available to
837 talk to the UDC device
839 CFG_CONSOLE_IS_IN_ENV
840 Define this if you want stdin, stdout &/or stderr to
844 CFG_USB_EXTC_CLK 0xBLAH
845 Derive USB clock from external clock "blah"
846 - CFG_USB_EXTC_CLK 0x02
848 CFG_USB_BRG_CLK 0xBLAH
849 Derive USB clock from brgclk
850 - CFG_USB_BRG_CLK 0x04
852 If you have a USB-IF assigned VendorID then you may wish to
853 define your own vendor specific values either in BoardName.h
854 or directly in usbd_vendor_info.h. If you don't define
855 CONFIG_USBD_MANUFACTURER, CONFIG_USBD_PRODUCT_NAME,
856 CONFIG_USBD_VENDORID and CONFIG_USBD_PRODUCTID, then U-Boot
857 should pretend to be a Linux device to it's target host.
859 CONFIG_USBD_MANUFACTURER
860 Define this string as the name of your company for
861 - CONFIG_USBD_MANUFACTURER "my company"
863 CONFIG_USBD_PRODUCT_NAME
864 Define this string as the name of your product
865 - CONFIG_USBD_PRODUCT_NAME "acme usb device"
868 Define this as your assigned Vendor ID from the USB
869 Implementors Forum. This *must* be a genuine Vendor ID
870 to avoid polluting the USB namespace.
871 - CONFIG_USBD_VENDORID 0xFFFF
873 CONFIG_USBD_PRODUCTID
874 Define this as the unique Product ID
876 - CONFIG_USBD_PRODUCTID 0xFFFF
880 The MMC controller on the Intel PXA is supported. To
881 enable this define CONFIG_MMC. The MMC can be
882 accessed from the boot prompt by mapping the device
883 to physical memory similar to flash. Command line is
884 enabled with CONFIG_CMD_MMC. The MMC driver also works with
885 the FAT fs. This is enabled with CONFIG_CMD_FAT.
887 - Journaling Flash filesystem support:
888 CONFIG_JFFS2_NAND, CONFIG_JFFS2_NAND_OFF, CONFIG_JFFS2_NAND_SIZE,
889 CONFIG_JFFS2_NAND_DEV
890 Define these for a default partition on a NAND device
892 CFG_JFFS2_FIRST_SECTOR,
893 CFG_JFFS2_FIRST_BANK, CFG_JFFS2_NUM_BANKS
894 Define these for a default partition on a NOR device
897 Define this to create an own partition. You have to provide a
898 function struct part_info* jffs2_part_info(int part_num)
900 If you define only one JFFS2 partition you may also want to
901 #define CFG_JFFS_SINGLE_PART 1
902 to disable the command chpart. This is the default when you
903 have not defined a custom partition
908 Define this to enable standard (PC-Style) keyboard
912 Standard PC keyboard driver with US (is default) and
913 GERMAN key layout (switch via environment 'keymap=de') support.
914 Export function i8042_kbd_init, i8042_tstc and i8042_getc
915 for cfb_console. Supports cursor blinking.
920 Define this to enable video support (for output to
925 Enable Chips & Technologies 69000 Video chip
927 CONFIG_VIDEO_SMI_LYNXEM
928 Enable Silicon Motion SMI 712/710/810 Video chip. The
929 video output is selected via environment 'videoout'
930 (1 = LCD and 2 = CRT). If videoout is undefined, CRT is
933 For the CT69000 and SMI_LYNXEM drivers, videomode is
934 selected via environment 'videomode'. Two diferent ways
936 - "videomode=num" 'num' is a standard LiLo mode numbers.
937 Following standard modes are supported (* is default):
939 Colors 640x480 800x600 1024x768 1152x864 1280x1024
940 -------------+---------------------------------------------
941 8 bits | 0x301* 0x303 0x305 0x161 0x307
942 15 bits | 0x310 0x313 0x316 0x162 0x319
943 16 bits | 0x311 0x314 0x317 0x163 0x31A
944 24 bits | 0x312 0x315 0x318 ? 0x31B
945 -------------+---------------------------------------------
946 (i.e. setenv videomode 317; saveenv; reset;)
948 - "videomode=bootargs" all the video parameters are parsed
949 from the bootargs. (See drivers/video/videomodes.c)
952 CONFIG_VIDEO_SED13806
953 Enable Epson SED13806 driver. This driver supports 8bpp
954 and 16bpp modes defined by CONFIG_VIDEO_SED13806_8BPP
955 or CONFIG_VIDEO_SED13806_16BPP
960 Define this to enable a custom keyboard support.
961 This simply calls drv_keyboard_init() which must be
962 defined in your board-specific files.
963 The only board using this so far is RBC823.
965 - LCD Support: CONFIG_LCD
967 Define this to enable LCD support (for output to LCD
968 display); also select one of the supported displays
969 by defining one of these:
971 CONFIG_NEC_NL6448AC33:
973 NEC NL6448AC33-18. Active, color, single scan.
975 CONFIG_NEC_NL6448BC20
977 NEC NL6448BC20-08. 6.5", 640x480.
978 Active, color, single scan.
980 CONFIG_NEC_NL6448BC33_54
982 NEC NL6448BC33-54. 10.4", 640x480.
983 Active, color, single scan.
987 Sharp 320x240. Active, color, single scan.
988 It isn't 16x9, and I am not sure what it is.
990 CONFIG_SHARP_LQ64D341
992 Sharp LQ64D341 display, 640x480.
993 Active, color, single scan.
997 HLD1045 display, 640x480.
998 Active, color, single scan.
1002 Optrex CBL50840-2 NF-FW 99 22 M5
1004 Hitachi LMG6912RPFC-00T
1008 320x240. Black & white.
1010 Normally display is black on white background; define
1011 CFG_WHITE_ON_BLACK to get it inverted.
1013 - Splash Screen Support: CONFIG_SPLASH_SCREEN
1015 If this option is set, the environment is checked for
1016 a variable "splashimage". If found, the usual display
1017 of logo, copyright and system information on the LCD
1018 is suppressed and the BMP image at the address
1019 specified in "splashimage" is loaded instead. The
1020 console is redirected to the "nulldev", too. This
1021 allows for a "silent" boot where a splash screen is
1022 loaded very quickly after power-on.
1024 - Gzip compressed BMP image support: CONFIG_VIDEO_BMP_GZIP
1026 If this option is set, additionally to standard BMP
1027 images, gzipped BMP images can be displayed via the
1028 splashscreen support or the bmp command.
1030 - Compression support:
1033 If this option is set, support for bzip2 compressed
1034 images is included. If not, only uncompressed and gzip
1035 compressed images are supported.
1037 NOTE: the bzip2 algorithm requires a lot of RAM, so
1038 the malloc area (as defined by CFG_MALLOC_LEN) should
1044 The address of PHY on MII bus.
1046 CONFIG_PHY_CLOCK_FREQ (ppc4xx)
1048 The clock frequency of the MII bus
1052 If this option is set, support for speed/duplex
1053 detection of Gigabit PHY is included.
1055 CONFIG_PHY_RESET_DELAY
1057 Some PHY like Intel LXT971A need extra delay after
1058 reset before any MII register access is possible.
1059 For such PHY, set this option to the usec delay
1060 required. (minimum 300usec for LXT971A)
1062 CONFIG_PHY_CMD_DELAY (ppc4xx)
1064 Some PHY like Intel LXT971A need extra delay after
1065 command issued before MII status register can be read
1072 Define a default value for ethernet address to use
1073 for the respective ethernet interface, in case this
1074 is not determined automatically.
1079 Define a default value for the IP address to use for
1080 the default ethernet interface, in case this is not
1081 determined through e.g. bootp.
1083 - Server IP address:
1086 Defines a default value for theIP address of a TFTP
1087 server to contact when using the "tftboot" command.
1089 - Multicast TFTP Mode:
1092 Defines whether you want to support multicast TFTP as per
1093 rfc-2090; for example to work with atftp. Lets lots of targets
1094 tftp down the same boot image concurrently. Note: the ethernet
1095 driver in use must provide a function: mcast() to join/leave a
1098 CONFIG_BOOTP_RANDOM_DELAY
1099 - BOOTP Recovery Mode:
1100 CONFIG_BOOTP_RANDOM_DELAY
1102 If you have many targets in a network that try to
1103 boot using BOOTP, you may want to avoid that all
1104 systems send out BOOTP requests at precisely the same
1105 moment (which would happen for instance at recovery
1106 from a power failure, when all systems will try to
1107 boot, thus flooding the BOOTP server. Defining
1108 CONFIG_BOOTP_RANDOM_DELAY causes a random delay to be
1109 inserted before sending out BOOTP requests. The
1110 following delays are inserted then:
1112 1st BOOTP request: delay 0 ... 1 sec
1113 2nd BOOTP request: delay 0 ... 2 sec
1114 3rd BOOTP request: delay 0 ... 4 sec
1116 BOOTP requests: delay 0 ... 8 sec
1118 - DHCP Advanced Options:
1119 You can fine tune the DHCP functionality by defining
1120 CONFIG_BOOTP_* symbols:
1122 CONFIG_BOOTP_SUBNETMASK
1123 CONFIG_BOOTP_GATEWAY
1124 CONFIG_BOOTP_HOSTNAME
1125 CONFIG_BOOTP_NISDOMAIN
1126 CONFIG_BOOTP_BOOTPATH
1127 CONFIG_BOOTP_BOOTFILESIZE
1130 CONFIG_BOOTP_SEND_HOSTNAME
1131 CONFIG_BOOTP_NTPSERVER
1132 CONFIG_BOOTP_TIMEOFFSET
1133 CONFIG_BOOTP_VENDOREX
1135 CONFIG_BOOTP_SERVERIP - TFTP server will be the serverip
1136 environment variable, not the BOOTP server.
1138 CONFIG_BOOTP_DNS2 - If a DHCP client requests the DNS
1139 serverip from a DHCP server, it is possible that more
1140 than one DNS serverip is offered to the client.
1141 If CONFIG_BOOTP_DNS2 is enabled, the secondary DNS
1142 serverip will be stored in the additional environment
1143 variable "dnsip2". The first DNS serverip is always
1144 stored in the variable "dnsip", when CONFIG_BOOTP_DNS
1147 CONFIG_BOOTP_SEND_HOSTNAME - Some DHCP servers are capable
1148 to do a dynamic update of a DNS server. To do this, they
1149 need the hostname of the DHCP requester.
1150 If CONFIG_BOOTP_SEND_HOSTNAME is defined, the content
1151 of the "hostname" environment variable is passed as
1152 option 12 to the DHCP server.
1155 CONFIG_CDP_DEVICE_ID
1157 The device id used in CDP trigger frames.
1159 CONFIG_CDP_DEVICE_ID_PREFIX
1161 A two character string which is prefixed to the MAC address
1166 A printf format string which contains the ascii name of
1167 the port. Normally is set to "eth%d" which sets
1168 eth0 for the first ethernet, eth1 for the second etc.
1170 CONFIG_CDP_CAPABILITIES
1172 A 32bit integer which indicates the device capabilities;
1173 0x00000010 for a normal host which does not forwards.
1177 An ascii string containing the version of the software.
1181 An ascii string containing the name of the platform.
1185 A 32bit integer sent on the trigger.
1187 CONFIG_CDP_POWER_CONSUMPTION
1189 A 16bit integer containing the power consumption of the
1190 device in .1 of milliwatts.
1192 CONFIG_CDP_APPLIANCE_VLAN_TYPE
1194 A byte containing the id of the VLAN.
1196 - Status LED: CONFIG_STATUS_LED
1198 Several configurations allow to display the current
1199 status using a LED. For instance, the LED will blink
1200 fast while running U-Boot code, stop blinking as
1201 soon as a reply to a BOOTP request was received, and
1202 start blinking slow once the Linux kernel is running
1203 (supported by a status LED driver in the Linux
1204 kernel). Defining CONFIG_STATUS_LED enables this
1207 - CAN Support: CONFIG_CAN_DRIVER
1209 Defining CONFIG_CAN_DRIVER enables CAN driver support
1210 on those systems that support this (optional)
1211 feature, like the TQM8xxL modules.
1213 - I2C Support: CONFIG_HARD_I2C | CONFIG_SOFT_I2C
1215 These enable I2C serial bus commands. Defining either of
1216 (but not both of) CONFIG_HARD_I2C or CONFIG_SOFT_I2C will
1217 include the appropriate I2C driver for the selected cpu.
1219 This will allow you to use i2c commands at the u-boot
1220 command line (as long as you set CONFIG_CMD_I2C in
1221 CONFIG_COMMANDS) and communicate with i2c based realtime
1222 clock chips. See common/cmd_i2c.c for a description of the
1223 command line interface.
1225 CONFIG_I2C_CMD_TREE is a recommended option that places
1226 all I2C commands under a single 'i2c' root command. The
1227 older 'imm', 'imd', 'iprobe' etc. commands are considered
1228 deprecated and may disappear in the future.
1230 CONFIG_HARD_I2C selects a hardware I2C controller.
1232 CONFIG_SOFT_I2C configures u-boot to use a software (aka
1233 bit-banging) driver instead of CPM or similar hardware
1236 There are several other quantities that must also be
1237 defined when you define CONFIG_HARD_I2C or CONFIG_SOFT_I2C.
1239 In both cases you will need to define CFG_I2C_SPEED
1240 to be the frequency (in Hz) at which you wish your i2c bus
1241 to run and CFG_I2C_SLAVE to be the address of this node (ie
1242 the cpu's i2c node address).
1244 Now, the u-boot i2c code for the mpc8xx (cpu/mpc8xx/i2c.c)
1245 sets the cpu up as a master node and so its address should
1246 therefore be cleared to 0 (See, eg, MPC823e User's Manual
1247 p.16-473). So, set CFG_I2C_SLAVE to 0.
1249 That's all that's required for CONFIG_HARD_I2C.
1251 If you use the software i2c interface (CONFIG_SOFT_I2C)
1252 then the following macros need to be defined (examples are
1253 from include/configs/lwmon.h):
1257 (Optional). Any commands necessary to enable the I2C
1258 controller or configure ports.
1260 eg: #define I2C_INIT (immr->im_cpm.cp_pbdir |= PB_SCL)
1264 (Only for MPC8260 CPU). The I/O port to use (the code
1265 assumes both bits are on the same port). Valid values
1266 are 0..3 for ports A..D.
1270 The code necessary to make the I2C data line active
1271 (driven). If the data line is open collector, this
1274 eg: #define I2C_ACTIVE (immr->im_cpm.cp_pbdir |= PB_SDA)
1278 The code necessary to make the I2C data line tri-stated
1279 (inactive). If the data line is open collector, this
1282 eg: #define I2C_TRISTATE (immr->im_cpm.cp_pbdir &= ~PB_SDA)
1286 Code that returns TRUE if the I2C data line is high,
1289 eg: #define I2C_READ ((immr->im_cpm.cp_pbdat & PB_SDA) != 0)
1293 If <bit> is TRUE, sets the I2C data line high. If it
1294 is FALSE, it clears it (low).
1296 eg: #define I2C_SDA(bit) \
1297 if(bit) immr->im_cpm.cp_pbdat |= PB_SDA; \
1298 else immr->im_cpm.cp_pbdat &= ~PB_SDA
1302 If <bit> is TRUE, sets the I2C clock line high. If it
1303 is FALSE, it clears it (low).
1305 eg: #define I2C_SCL(bit) \
1306 if(bit) immr->im_cpm.cp_pbdat |= PB_SCL; \
1307 else immr->im_cpm.cp_pbdat &= ~PB_SCL
1311 This delay is invoked four times per clock cycle so this
1312 controls the rate of data transfer. The data rate thus
1313 is 1 / (I2C_DELAY * 4). Often defined to be something
1316 #define I2C_DELAY udelay(2)
1320 When a board is reset during an i2c bus transfer
1321 chips might think that the current transfer is still
1322 in progress. On some boards it is possible to access
1323 the i2c SCLK line directly, either by using the
1324 processor pin as a GPIO or by having a second pin
1325 connected to the bus. If this option is defined a
1326 custom i2c_init_board() routine in boards/xxx/board.c
1327 is run early in the boot sequence.
1329 CONFIG_I2CFAST (PPC405GP|PPC405EP only)
1331 This option enables configuration of bi_iic_fast[] flags
1332 in u-boot bd_info structure based on u-boot environment
1333 variable "i2cfast". (see also i2cfast)
1335 CONFIG_I2C_MULTI_BUS
1337 This option allows the use of multiple I2C buses, each of which
1338 must have a controller. At any point in time, only one bus is
1339 active. To switch to a different bus, use the 'i2c dev' command.
1340 Note that bus numbering is zero-based.
1344 This option specifies a list of I2C devices that will be skipped
1345 when the 'i2c probe' command is issued (or 'iprobe' using the legacy
1346 command). If CONFIG_I2C_MULTI_BUS is set, specify a list of bus-device
1347 pairs. Otherwise, specify a 1D array of device addresses
1350 #undef CONFIG_I2C_MULTI_BUS
1351 #define CFG_I2C_NOPROBES {0x50,0x68}
1353 will skip addresses 0x50 and 0x68 on a board with one I2C bus
1355 #define CONFIG_I2C_MULTI_BUS
1356 #define CFG_I2C_MULTI_NOPROBES {{0,0x50},{0,0x68},{1,0x54}}
1358 will skip addresses 0x50 and 0x68 on bus 0 and address 0x54 on bus 1
1362 If defined, then this indicates the I2C bus number for DDR SPD.
1363 If not defined, then U-Boot assumes that SPD is on I2C bus 0.
1367 If defined, then this indicates the I2C bus number for the RTC.
1368 If not defined, then U-Boot assumes that RTC is on I2C bus 0.
1372 If defined, then this indicates the I2C bus number for the DTT.
1373 If not defined, then U-Boot assumes that DTT is on I2C bus 0.
1377 Define this option if you want to use Freescale's I2C driver in
1378 drivers/i2c/fsl_i2c.c.
1381 - SPI Support: CONFIG_SPI
1383 Enables SPI driver (so far only tested with
1384 SPI EEPROM, also an instance works with Crystal A/D and
1385 D/As on the SACSng board)
1389 Enables extended (16-bit) SPI EEPROM addressing.
1390 (symmetrical to CONFIG_I2C_X)
1394 Enables a software (bit-bang) SPI driver rather than
1395 using hardware support. This is a general purpose
1396 driver that only requires three general I/O port pins
1397 (two outputs, one input) to function. If this is
1398 defined, the board configuration must define several
1399 SPI configuration items (port pins to use, etc). For
1400 an example, see include/configs/sacsng.h.
1404 Enables a hardware SPI driver for general-purpose reads
1405 and writes. As with CONFIG_SOFT_SPI, the board configuration
1406 must define a list of chip-select function pointers.
1407 Currently supported on some MPC8xxx processors. For an
1408 example, see include/configs/mpc8349emds.h.
1410 - FPGA Support: CONFIG_FPGA
1412 Enables FPGA subsystem.
1414 CONFIG_FPGA_<vendor>
1416 Enables support for specific chip vendors.
1419 CONFIG_FPGA_<family>
1421 Enables support for FPGA family.
1422 (SPARTAN2, SPARTAN3, VIRTEX2, CYCLONE2, ACEX1K, ACEX)
1426 Specify the number of FPGA devices to support.
1428 CFG_FPGA_PROG_FEEDBACK
1430 Enable printing of hash marks during FPGA configuration.
1434 Enable checks on FPGA configuration interface busy
1435 status by the configuration function. This option
1436 will require a board or device specific function to
1441 If defined, a function that provides delays in the FPGA
1442 configuration driver.
1444 CFG_FPGA_CHECK_CTRLC
1445 Allow Control-C to interrupt FPGA configuration
1447 CFG_FPGA_CHECK_ERROR
1449 Check for configuration errors during FPGA bitfile
1450 loading. For example, abort during Virtex II
1451 configuration if the INIT_B line goes low (which
1452 indicated a CRC error).
1456 Maximum time to wait for the INIT_B line to deassert
1457 after PROB_B has been deasserted during a Virtex II
1458 FPGA configuration sequence. The default time is 500
1463 Maximum time to wait for BUSY to deassert during
1464 Virtex II FPGA configuration. The default is 5 mS.
1466 CFG_FPGA_WAIT_CONFIG
1468 Time to wait after FPGA configuration. The default is
1471 - Configuration Management:
1474 If defined, this string will be added to the U-Boot
1475 version information (U_BOOT_VERSION)
1477 - Vendor Parameter Protection:
1479 U-Boot considers the values of the environment
1480 variables "serial#" (Board Serial Number) and
1481 "ethaddr" (Ethernet Address) to be parameters that
1482 are set once by the board vendor / manufacturer, and
1483 protects these variables from casual modification by
1484 the user. Once set, these variables are read-only,
1485 and write or delete attempts are rejected. You can
1486 change this behviour:
1488 If CONFIG_ENV_OVERWRITE is #defined in your config
1489 file, the write protection for vendor parameters is
1490 completely disabled. Anybody can change or delete
1493 Alternatively, if you #define _both_ CONFIG_ETHADDR
1494 _and_ CONFIG_OVERWRITE_ETHADDR_ONCE, a default
1495 ethernet address is installed in the environment,
1496 which can be changed exactly ONCE by the user. [The
1497 serial# is unaffected by this, i. e. it remains
1503 Define this variable to enable the reservation of
1504 "protected RAM", i. e. RAM which is not overwritten
1505 by U-Boot. Define CONFIG_PRAM to hold the number of
1506 kB you want to reserve for pRAM. You can overwrite
1507 this default value by defining an environment
1508 variable "pram" to the number of kB you want to
1509 reserve. Note that the board info structure will
1510 still show the full amount of RAM. If pRAM is
1511 reserved, a new environment variable "mem" will
1512 automatically be defined to hold the amount of
1513 remaining RAM in a form that can be passed as boot
1514 argument to Linux, for instance like that:
1516 setenv bootargs ... mem=\${mem}
1519 This way you can tell Linux not to use this memory,
1520 either, which results in a memory region that will
1521 not be affected by reboots.
1523 *WARNING* If your board configuration uses automatic
1524 detection of the RAM size, you must make sure that
1525 this memory test is non-destructive. So far, the
1526 following board configurations are known to be
1529 ETX094, IVMS8, IVML24, SPD8xx, TQM8xxL,
1530 HERMES, IP860, RPXlite, LWMON, LANTEC,
1531 PCU_E, FLAGADM, TQM8260
1536 Define this variable to stop the system in case of a
1537 fatal error, so that you have to reset it manually.
1538 This is probably NOT a good idea for an embedded
1539 system where you want to system to reboot
1540 automatically as fast as possible, but it may be
1541 useful during development since you can try to debug
1542 the conditions that lead to the situation.
1544 CONFIG_NET_RETRY_COUNT
1546 This variable defines the number of retries for
1547 network operations like ARP, RARP, TFTP, or BOOTP
1548 before giving up the operation. If not defined, a
1549 default value of 5 is used.
1551 - Command Interpreter:
1552 CONFIG_AUTO_COMPLETE
1554 Enable auto completion of commands using TAB.
1556 Note that this feature has NOT been implemented yet
1557 for the "hush" shell.
1562 Define this variable to enable the "hush" shell (from
1563 Busybox) as command line interpreter, thus enabling
1564 powerful command line syntax like
1565 if...then...else...fi conditionals or `&&' and '||'
1566 constructs ("shell scripts").
1568 If undefined, you get the old, much simpler behaviour
1569 with a somewhat smaller memory footprint.
1574 This defines the secondary prompt string, which is
1575 printed when the command interpreter needs more input
1576 to complete a command. Usually "> ".
1580 In the current implementation, the local variables
1581 space and global environment variables space are
1582 separated. Local variables are those you define by
1583 simply typing `name=value'. To access a local
1584 variable later on, you have write `$name' or
1585 `${name}'; to execute the contents of a variable
1586 directly type `$name' at the command prompt.
1588 Global environment variables are those you use
1589 setenv/printenv to work with. To run a command stored
1590 in such a variable, you need to use the run command,
1591 and you must not use the '$' sign to access them.
1593 To store commands and special characters in a
1594 variable, please use double quotation marks
1595 surrounding the whole text of the variable, instead
1596 of the backslashes before semicolons and special
1599 - Commandline Editing and History:
1600 CONFIG_CMDLINE_EDITING
1602 Enable editiong and History functions for interactive
1603 commandline input operations
1605 - Default Environment:
1606 CONFIG_EXTRA_ENV_SETTINGS
1608 Define this to contain any number of null terminated
1609 strings (variable = value pairs) that will be part of
1610 the default environment compiled into the boot image.
1612 For example, place something like this in your
1613 board's config file:
1615 #define CONFIG_EXTRA_ENV_SETTINGS \
1619 Warning: This method is based on knowledge about the
1620 internal format how the environment is stored by the
1621 U-Boot code. This is NOT an official, exported
1622 interface! Although it is unlikely that this format
1623 will change soon, there is no guarantee either.
1624 You better know what you are doing here.
1626 Note: overly (ab)use of the default environment is
1627 discouraged. Make sure to check other ways to preset
1628 the environment like the autoscript function or the
1631 - DataFlash Support:
1632 CONFIG_HAS_DATAFLASH
1634 Defining this option enables DataFlash features and
1635 allows to read/write in Dataflash via the standard
1638 - SystemACE Support:
1641 Adding this option adds support for Xilinx SystemACE
1642 chips attached via some sort of local bus. The address
1643 of the chip must alsh be defined in the
1644 CFG_SYSTEMACE_BASE macro. For example:
1646 #define CONFIG_SYSTEMACE
1647 #define CFG_SYSTEMACE_BASE 0xf0000000
1649 When SystemACE support is added, the "ace" device type
1650 becomes available to the fat commands, i.e. fatls.
1652 - TFTP Fixed UDP Port:
1655 If this is defined, the environment variable tftpsrcp
1656 is used to supply the TFTP UDP source port value.
1657 If tftpsrcp isn't defined, the normal pseudo-random port
1658 number generator is used.
1660 Also, the environment variable tftpdstp is used to supply
1661 the TFTP UDP destination port value. If tftpdstp isn't
1662 defined, the normal port 69 is used.
1664 The purpose for tftpsrcp is to allow a TFTP server to
1665 blindly start the TFTP transfer using the pre-configured
1666 target IP address and UDP port. This has the effect of
1667 "punching through" the (Windows XP) firewall, allowing
1668 the remainder of the TFTP transfer to proceed normally.
1669 A better solution is to properly configure the firewall,
1670 but sometimes that is not allowed.
1672 - Show boot progress:
1673 CONFIG_SHOW_BOOT_PROGRESS
1675 Defining this option allows to add some board-
1676 specific code (calling a user-provided function
1677 "show_boot_progress(int)") that enables you to show
1678 the system's boot progress on some display (for
1679 example, some LED's) on your board. At the moment,
1680 the following checkpoints are implemented:
1682 Legacy uImage format:
1685 1 common/cmd_bootm.c before attempting to boot an image
1686 -1 common/cmd_bootm.c Image header has bad magic number
1687 2 common/cmd_bootm.c Image header has correct magic number
1688 -2 common/cmd_bootm.c Image header has bad checksum
1689 3 common/cmd_bootm.c Image header has correct checksum
1690 -3 common/cmd_bootm.c Image data has bad checksum
1691 4 common/cmd_bootm.c Image data has correct checksum
1692 -4 common/cmd_bootm.c Image is for unsupported architecture
1693 5 common/cmd_bootm.c Architecture check OK
1694 -5 common/cmd_bootm.c Wrong Image Type (not kernel, multi)
1695 6 common/cmd_bootm.c Image Type check OK
1696 -6 common/cmd_bootm.c gunzip uncompression error
1697 -7 common/cmd_bootm.c Unimplemented compression type
1698 7 common/cmd_bootm.c Uncompression OK
1699 8 common/cmd_bootm.c No uncompress/copy overwrite error
1700 -9 common/cmd_bootm.c Unsupported OS (not Linux, BSD, VxWorks, QNX)
1702 9 common/image.c Start initial ramdisk verification
1703 -10 common/image.c Ramdisk header has bad magic number
1704 -11 common/image.c Ramdisk header has bad checksum
1705 10 common/image.c Ramdisk header is OK
1706 -12 common/image.c Ramdisk data has bad checksum
1707 11 common/image.c Ramdisk data has correct checksum
1708 12 common/image.c Ramdisk verification complete, start loading
1709 -13 common/image.c Wrong Image Type (not PPC Linux Ramdisk)
1710 13 common/image.c Start multifile image verification
1711 14 common/image.c No initial ramdisk, no multifile, continue.
1713 15 lib_<arch>/bootm.c All preparation done, transferring control to OS
1715 -30 lib_ppc/board.c Fatal error, hang the system
1716 -31 post/post.c POST test failed, detected by post_output_backlog()
1717 -32 post/post.c POST test failed, detected by post_run_single()
1719 34 common/cmd_doc.c before loading a Image from a DOC device
1720 -35 common/cmd_doc.c Bad usage of "doc" command
1721 35 common/cmd_doc.c correct usage of "doc" command
1722 -36 common/cmd_doc.c No boot device
1723 36 common/cmd_doc.c correct boot device
1724 -37 common/cmd_doc.c Unknown Chip ID on boot device
1725 37 common/cmd_doc.c correct chip ID found, device available
1726 -38 common/cmd_doc.c Read Error on boot device
1727 38 common/cmd_doc.c reading Image header from DOC device OK
1728 -39 common/cmd_doc.c Image header has bad magic number
1729 39 common/cmd_doc.c Image header has correct magic number
1730 -40 common/cmd_doc.c Error reading Image from DOC device
1731 40 common/cmd_doc.c Image header has correct magic number
1732 41 common/cmd_ide.c before loading a Image from a IDE device
1733 -42 common/cmd_ide.c Bad usage of "ide" command
1734 42 common/cmd_ide.c correct usage of "ide" command
1735 -43 common/cmd_ide.c No boot device
1736 43 common/cmd_ide.c boot device found
1737 -44 common/cmd_ide.c Device not available
1738 44 common/cmd_ide.c Device available
1739 -45 common/cmd_ide.c wrong partition selected
1740 45 common/cmd_ide.c partition selected
1741 -46 common/cmd_ide.c Unknown partition table
1742 46 common/cmd_ide.c valid partition table found
1743 -47 common/cmd_ide.c Invalid partition type
1744 47 common/cmd_ide.c correct partition type
1745 -48 common/cmd_ide.c Error reading Image Header on boot device
1746 48 common/cmd_ide.c reading Image Header from IDE device OK
1747 -49 common/cmd_ide.c Image header has bad magic number
1748 49 common/cmd_ide.c Image header has correct magic number
1749 -50 common/cmd_ide.c Image header has bad checksum
1750 50 common/cmd_ide.c Image header has correct checksum
1751 -51 common/cmd_ide.c Error reading Image from IDE device
1752 51 common/cmd_ide.c reading Image from IDE device OK
1753 52 common/cmd_nand.c before loading a Image from a NAND device
1754 -53 common/cmd_nand.c Bad usage of "nand" command
1755 53 common/cmd_nand.c correct usage of "nand" command
1756 -54 common/cmd_nand.c No boot device
1757 54 common/cmd_nand.c boot device found
1758 -55 common/cmd_nand.c Unknown Chip ID on boot device
1759 55 common/cmd_nand.c correct chip ID found, device available
1760 -56 common/cmd_nand.c Error reading Image Header on boot device
1761 56 common/cmd_nand.c reading Image Header from NAND device OK
1762 -57 common/cmd_nand.c Image header has bad magic number
1763 57 common/cmd_nand.c Image header has correct magic number
1764 -58 common/cmd_nand.c Error reading Image from NAND device
1765 58 common/cmd_nand.c reading Image from NAND device OK
1767 -60 common/env_common.c Environment has a bad CRC, using default
1769 64 net/eth.c starting with Ethernetconfiguration.
1770 -64 net/eth.c no Ethernet found.
1771 65 net/eth.c Ethernet found.
1773 -80 common/cmd_net.c usage wrong
1774 80 common/cmd_net.c before calling NetLoop()
1775 -81 common/cmd_net.c some error in NetLoop() occured
1776 81 common/cmd_net.c NetLoop() back without error
1777 -82 common/cmd_net.c size == 0 (File with size 0 loaded)
1778 82 common/cmd_net.c trying automatic boot
1779 83 common/cmd_net.c running autoscript
1780 -83 common/cmd_net.c some error in automatic boot or autoscript
1781 84 common/cmd_net.c end without errors
1786 100 common/cmd_bootm.c Kernel FIT Image has correct format
1787 -100 common/cmd_bootm.c Kernel FIT Image has incorrect format
1788 101 common/cmd_bootm.c No Kernel subimage unit name, using configuration
1789 -101 common/cmd_bootm.c Can't get configuration for kernel subimage
1790 102 common/cmd_bootm.c Kernel unit name specified
1791 -103 common/cmd_bootm.c Can't get kernel subimage node offset
1792 103 common/cmd_bootm.c Found configuration node
1793 104 common/cmd_bootm.c Got kernel subimage node offset
1794 -104 common/cmd_bootm.c Kernel subimage hash verification failed
1795 105 common/cmd_bootm.c Kernel subimage hash verification OK
1796 -105 common/cmd_bootm.c Kernel subimage is for unsupported architecture
1797 106 common/cmd_bootm.c Architecture check OK
1798 -106 common/cmd_bootm.c Kernel subimage has wrong typea
1799 107 common/cmd_bootm.c Kernel subimge type OK
1800 -107 common/cmd_bootm.c Can't get kernel subimage data/size
1801 108 common/cmd_bootm.c Got kernel subimage data/size
1802 -108 common/cmd_bootm.c Wrong image type (not legacy, FIT)
1803 -109 common/cmd_bootm.c Can't get kernel subimage type
1804 -110 common/cmd_bootm.c Can't get kernel subimage comp
1805 -111 common/cmd_bootm.c Can't get kernel subimage os
1806 -112 common/cmd_bootm.c Can't get kernel subimage load address
1807 -113 common/cmd_bootm.c Image uncompress/copy overwrite error
1809 120 common/image.c Start initial ramdisk verification
1810 -120 common/image.c Ramdisk FIT image has incorrect format
1811 121 common/image.c Ramdisk FIT image has correct format
1812 122 common/image.c No Ramdisk subimage unit name, using configuration
1813 -122 common/image.c Can't get configuration for ramdisk subimage
1814 123 common/image.c Ramdisk unit name specified
1815 -124 common/image.c Can't get ramdisk subimage node offset
1816 125 common/image.c Got ramdisk subimage node offset
1817 -125 common/image.c Ramdisk subimage hash verification failed
1818 126 common/image.c Ramdisk subimage hash verification OK
1819 -126 common/image.c Ramdisk subimage for unsupported architecture
1820 127 common/image.c Architecture check OK
1821 -127 common/image.c Can't get ramdisk subimage data/size
1822 128 common/image.c Got ramdisk subimage data/size
1823 129 common/image.c Can't get ramdisk load address
1824 -129 common/image.c Got ramdisk load address
1826 -130 common/cmd_doc.c Icorrect FIT image format
1827 131 common/cmd_doc.c FIT image format OK
1829 -140 common/cmd_ide.c Icorrect FIT image format
1830 141 common/cmd_ide.c FIT image format OK
1832 -150 common/cmd_nand.c Icorrect FIT image format
1833 151 common/cmd_nand.c FIT image format OK
1839 [so far only for SMDK2400 and TRAB boards]
1841 - Modem support endable:
1842 CONFIG_MODEM_SUPPORT
1844 - RTS/CTS Flow control enable:
1847 - Modem debug support:
1848 CONFIG_MODEM_SUPPORT_DEBUG
1850 Enables debugging stuff (char screen[1024], dbg())
1851 for modem support. Useful only with BDI2000.
1853 - Interrupt support (PPC):
1855 There are common interrupt_init() and timer_interrupt()
1856 for all PPC archs. interrupt_init() calls interrupt_init_cpu()
1857 for cpu specific initialization. interrupt_init_cpu()
1858 should set decrementer_count to appropriate value. If
1859 cpu resets decrementer automatically after interrupt
1860 (ppc4xx) it should set decrementer_count to zero.
1861 timer_interrupt() calls timer_interrupt_cpu() for cpu
1862 specific handling. If board has watchdog / status_led
1863 / other_activity_monitor it works automatically from
1864 general timer_interrupt().
1868 In the target system modem support is enabled when a
1869 specific key (key combination) is pressed during
1870 power-on. Otherwise U-Boot will boot normally
1871 (autoboot). The key_pressed() fuction is called from
1872 board_init(). Currently key_pressed() is a dummy
1873 function, returning 1 and thus enabling modem
1876 If there are no modem init strings in the
1877 environment, U-Boot proceed to autoboot; the
1878 previous output (banner, info printfs) will be
1881 See also: doc/README.Modem
1884 Configuration Settings:
1885 -----------------------
1887 - CFG_LONGHELP: Defined when you want long help messages included;
1888 undefine this when you're short of memory.
1890 - CFG_PROMPT: This is what U-Boot prints on the console to
1891 prompt for user input.
1893 - CFG_CBSIZE: Buffer size for input from the Console
1895 - CFG_PBSIZE: Buffer size for Console output
1897 - CFG_MAXARGS: max. Number of arguments accepted for monitor commands
1899 - CFG_BARGSIZE: Buffer size for Boot Arguments which are passed to
1900 the application (usually a Linux kernel) when it is
1903 - CFG_BAUDRATE_TABLE:
1904 List of legal baudrate settings for this board.
1906 - CFG_CONSOLE_INFO_QUIET
1907 Suppress display of console information at boot.
1909 - CFG_CONSOLE_IS_IN_ENV
1910 If the board specific function
1911 extern int overwrite_console (void);
1912 returns 1, the stdin, stderr and stdout are switched to the
1913 serial port, else the settings in the environment are used.
1915 - CFG_CONSOLE_OVERWRITE_ROUTINE
1916 Enable the call to overwrite_console().
1918 - CFG_CONSOLE_ENV_OVERWRITE
1919 Enable overwrite of previous console environment settings.
1921 - CFG_MEMTEST_START, CFG_MEMTEST_END:
1922 Begin and End addresses of the area used by the
1926 Enable an alternate, more extensive memory test.
1928 - CFG_MEMTEST_SCRATCH:
1929 Scratch address used by the alternate memory test
1930 You only need to set this if address zero isn't writeable
1932 - CFG_MEM_TOP_HIDE (PPC only):
1933 If CFG_MEM_TOP_HIDE is defined in the board config header,
1934 this specified memory area will get subtracted from the top
1935 (end) of ram and won't get "touched" at all by U-Boot. By
1936 fixing up gd->ram_size the Linux kernel should gets passed
1937 the now "corrected" memory size and won't touch it either.
1938 This should work for arch/ppc and arch/powerpc. Only Linux
1939 board ports in arch/powerpc with bootwrapper support that
1940 recalculate the memory size from the SDRAM controller setup
1941 will have to get fixed in Linux additionally.
1943 This option can be used as a workaround for the 440EPx/GRx
1944 CHIP 11 errata where the last 256 bytes in SDRAM shouldn't
1947 WARNING: Please make sure that this value is a multiple of
1948 the Linux page size (normally 4k). If this is not the case,
1949 then the end address of the Linux memory will be located at a
1950 non page size aligned address and this could cause major
1953 - CFG_TFTP_LOADADDR:
1954 Default load address for network file downloads
1956 - CFG_LOADS_BAUD_CHANGE:
1957 Enable temporary baudrate change while serial download
1960 Physical start address of SDRAM. _Must_ be 0 here.
1963 Physical start address of Motherboard I/O (if using a
1967 Physical start address of Flash memory.
1970 Physical start address of boot monitor code (set by
1971 make config files to be same as the text base address
1972 (TEXT_BASE) used when linking) - same as
1973 CFG_FLASH_BASE when booting from flash.
1976 Size of memory reserved for monitor code, used to
1977 determine _at_compile_time_ (!) if the environment is
1978 embedded within the U-Boot image, or in a separate
1982 Size of DRAM reserved for malloc() use.
1985 Normally compressed uImages are limited to an
1986 uncompressed size of 8 MBytes. If this is not enough,
1987 you can define CFG_BOOTM_LEN in your board config file
1988 to adjust this setting to your needs.
1991 Maximum size of memory mapped by the startup code of
1992 the Linux kernel; all data that must be processed by
1993 the Linux kernel (bd_info, boot arguments, eventually
1994 initrd image) must be put below this limit.
1996 - CFG_MAX_FLASH_BANKS:
1997 Max number of Flash memory banks
1999 - CFG_MAX_FLASH_SECT:
2000 Max number of sectors on a Flash chip
2002 - CFG_FLASH_ERASE_TOUT:
2003 Timeout for Flash erase operations (in ms)
2005 - CFG_FLASH_WRITE_TOUT:
2006 Timeout for Flash write operations (in ms)
2008 - CFG_FLASH_LOCK_TOUT
2009 Timeout for Flash set sector lock bit operation (in ms)
2011 - CFG_FLASH_UNLOCK_TOUT
2012 Timeout for Flash clear lock bits operation (in ms)
2014 - CFG_FLASH_PROTECTION
2015 If defined, hardware flash sectors protection is used
2016 instead of U-Boot software protection.
2018 - CFG_DIRECT_FLASH_TFTP:
2020 Enable TFTP transfers directly to flash memory;
2021 without this option such a download has to be
2022 performed in two steps: (1) download to RAM, and (2)
2023 copy from RAM to flash.
2025 The two-step approach is usually more reliable, since
2026 you can check if the download worked before you erase
2027 the flash, but in some situations (when sytem RAM is
2028 too limited to allow for a tempory copy of the
2029 downloaded image) this option may be very useful.
2032 Define if the flash driver uses extra elements in the
2033 common flash structure for storing flash geometry.
2035 - CFG_FLASH_CFI_DRIVER
2036 This option also enables the building of the cfi_flash driver
2037 in the drivers directory
2039 - CFG_FLASH_QUIET_TEST
2040 If this option is defined, the common CFI flash doesn't
2041 print it's warning upon not recognized FLASH banks. This
2042 is useful, if some of the configured banks are only
2043 optionally available.
2045 - CONFIG_FLASH_SHOW_PROGRESS
2046 If defined (must be an integer), print out countdown
2047 digits and dots. Recommended value: 45 (9..1) for 80
2048 column displays, 15 (3..1) for 40 column displays.
2050 - CFG_RX_ETH_BUFFER:
2051 Defines the number of ethernet receive buffers. On some
2052 ethernet controllers it is recommended to set this value
2053 to 8 or even higher (EEPRO100 or 405 EMAC), since all
2054 buffers can be full shortly after enabling the interface
2055 on high ethernet traffic.
2056 Defaults to 4 if not defined.
2058 The following definitions that deal with the placement and management
2059 of environment data (variable area); in general, we support the
2060 following configurations:
2062 - CFG_ENV_IS_IN_FLASH:
2064 Define this if the environment is in flash memory.
2066 a) The environment occupies one whole flash sector, which is
2067 "embedded" in the text segment with the U-Boot code. This
2068 happens usually with "bottom boot sector" or "top boot
2069 sector" type flash chips, which have several smaller
2070 sectors at the start or the end. For instance, such a
2071 layout can have sector sizes of 8, 2x4, 16, Nx32 kB. In
2072 such a case you would place the environment in one of the
2073 4 kB sectors - with U-Boot code before and after it. With
2074 "top boot sector" type flash chips, you would put the
2075 environment in one of the last sectors, leaving a gap
2076 between U-Boot and the environment.
2080 Offset of environment data (variable area) to the
2081 beginning of flash memory; for instance, with bottom boot
2082 type flash chips the second sector can be used: the offset
2083 for this sector is given here.
2085 CFG_ENV_OFFSET is used relative to CFG_FLASH_BASE.
2089 This is just another way to specify the start address of
2090 the flash sector containing the environment (instead of
2093 - CFG_ENV_SECT_SIZE:
2095 Size of the sector containing the environment.
2098 b) Sometimes flash chips have few, equal sized, BIG sectors.
2099 In such a case you don't want to spend a whole sector for
2104 If you use this in combination with CFG_ENV_IS_IN_FLASH
2105 and CFG_ENV_SECT_SIZE, you can specify to use only a part
2106 of this flash sector for the environment. This saves
2107 memory for the RAM copy of the environment.
2109 It may also save flash memory if you decide to use this
2110 when your environment is "embedded" within U-Boot code,
2111 since then the remainder of the flash sector could be used
2112 for U-Boot code. It should be pointed out that this is
2113 STRONGLY DISCOURAGED from a robustness point of view:
2114 updating the environment in flash makes it always
2115 necessary to erase the WHOLE sector. If something goes
2116 wrong before the contents has been restored from a copy in
2117 RAM, your target system will be dead.
2119 - CFG_ENV_ADDR_REDUND
2122 These settings describe a second storage area used to hold
2123 a redundand copy of the environment data, so that there is
2124 a valid backup copy in case there is a power failure during
2125 a "saveenv" operation.
2127 BE CAREFUL! Any changes to the flash layout, and some changes to the
2128 source code will make it necessary to adapt <board>/u-boot.lds*
2132 - CFG_ENV_IS_IN_NVRAM:
2134 Define this if you have some non-volatile memory device
2135 (NVRAM, battery buffered SRAM) which you want to use for the
2141 These two #defines are used to determin the memory area you
2142 want to use for environment. It is assumed that this memory
2143 can just be read and written to, without any special
2146 BE CAREFUL! The first access to the environment happens quite early
2147 in U-Boot initalization (when we try to get the setting of for the
2148 console baudrate). You *MUST* have mappend your NVRAM area then, or
2151 Please note that even with NVRAM we still use a copy of the
2152 environment in RAM: we could work on NVRAM directly, but we want to
2153 keep settings there always unmodified except somebody uses "saveenv"
2154 to save the current settings.
2157 - CFG_ENV_IS_IN_EEPROM:
2159 Use this if you have an EEPROM or similar serial access
2160 device and a driver for it.
2165 These two #defines specify the offset and size of the
2166 environment area within the total memory of your EEPROM.
2168 - CFG_I2C_EEPROM_ADDR:
2169 If defined, specified the chip address of the EEPROM device.
2170 The default address is zero.
2172 - CFG_EEPROM_PAGE_WRITE_BITS:
2173 If defined, the number of bits used to address bytes in a
2174 single page in the EEPROM device. A 64 byte page, for example
2175 would require six bits.
2177 - CFG_EEPROM_PAGE_WRITE_DELAY_MS:
2178 If defined, the number of milliseconds to delay between
2179 page writes. The default is zero milliseconds.
2181 - CFG_I2C_EEPROM_ADDR_LEN:
2182 The length in bytes of the EEPROM memory array address. Note
2183 that this is NOT the chip address length!
2185 - CFG_I2C_EEPROM_ADDR_OVERFLOW:
2186 EEPROM chips that implement "address overflow" are ones
2187 like Catalyst 24WC04/08/16 which has 9/10/11 bits of
2188 address and the extra bits end up in the "chip address" bit
2189 slots. This makes a 24WC08 (1Kbyte) chip look like four 256
2192 Note that we consider the length of the address field to
2193 still be one byte because the extra address bits are hidden
2194 in the chip address.
2197 The size in bytes of the EEPROM device.
2200 - CFG_ENV_IS_IN_DATAFLASH:
2202 Define this if you have a DataFlash memory device which you
2203 want to use for the environment.
2209 These three #defines specify the offset and size of the
2210 environment area within the total memory of your DataFlash placed
2211 at the specified address.
2213 - CFG_ENV_IS_IN_NAND:
2215 Define this if you have a NAND device which you want to use
2216 for the environment.
2221 These two #defines specify the offset and size of the environment
2222 area within the first NAND device.
2224 - CFG_ENV_OFFSET_REDUND
2226 This setting describes a second storage area of CFG_ENV_SIZE
2227 size used to hold a redundant copy of the environment data,
2228 so that there is a valid backup copy in case there is a
2229 power failure during a "saveenv" operation.
2231 Note: CFG_ENV_OFFSET and CFG_ENV_OFFSET_REDUND must be aligned
2232 to a block boundary, and CFG_ENV_SIZE must be a multiple of
2233 the NAND devices block size.
2235 - CFG_SPI_INIT_OFFSET
2237 Defines offset to the initial SPI buffer area in DPRAM. The
2238 area is used at an early stage (ROM part) if the environment
2239 is configured to reside in the SPI EEPROM: We need a 520 byte
2240 scratch DPRAM area. It is used between the two initialization
2241 calls (spi_init_f() and spi_init_r()). A value of 0xB00 seems
2242 to be a good choice since it makes it far enough from the
2243 start of the data area as well as from the stack pointer.
2245 Please note that the environment is read-only until the monitor
2246 has been relocated to RAM and a RAM copy of the environment has been
2247 created; also, when using EEPROM you will have to use getenv_r()
2248 until then to read environment variables.
2250 The environment is protected by a CRC32 checksum. Before the monitor
2251 is relocated into RAM, as a result of a bad CRC you will be working
2252 with the compiled-in default environment - *silently*!!! [This is
2253 necessary, because the first environment variable we need is the
2254 "baudrate" setting for the console - if we have a bad CRC, we don't
2255 have any device yet where we could complain.]
2257 Note: once the monitor has been relocated, then it will complain if
2258 the default environment is used; a new CRC is computed as soon as you
2259 use the "saveenv" command to store a valid environment.
2261 - CFG_FAULT_ECHO_LINK_DOWN:
2262 Echo the inverted Ethernet link state to the fault LED.
2264 Note: If this option is active, then CFG_FAULT_MII_ADDR
2265 also needs to be defined.
2267 - CFG_FAULT_MII_ADDR:
2268 MII address of the PHY to check for the Ethernet link state.
2270 - CFG_64BIT_VSPRINTF:
2271 Makes vsprintf (and all *printf functions) support printing
2272 of 64bit values by using the L quantifier
2274 - CFG_64BIT_STRTOUL:
2275 Adds simple_strtoull that returns a 64bit value
2277 Low Level (hardware related) configuration options:
2278 ---------------------------------------------------
2280 - CFG_CACHELINE_SIZE:
2281 Cache Line Size of the CPU.
2284 Default address of the IMMR after system reset.
2286 Needed on some 8260 systems (MPC8260ADS, PQ2FADS-ZU,
2287 and RPXsuper) to be able to adjust the position of
2288 the IMMR register after a reset.
2290 - Floppy Disk Support:
2291 CFG_FDC_DRIVE_NUMBER
2293 the default drive number (default value 0)
2297 defines the spacing between fdc chipset registers
2302 defines the offset of register from address. It
2303 depends on which part of the data bus is connected to
2304 the fdc chipset. (default value 0)
2306 If CFG_ISA_IO_STRIDE CFG_ISA_IO_OFFSET and
2307 CFG_FDC_DRIVE_NUMBER are undefined, they take their
2310 if CFG_FDC_HW_INIT is defined, then the function
2311 fdc_hw_init() is called at the beginning of the FDC
2312 setup. fdc_hw_init() must be provided by the board
2313 source code. It is used to make hardware dependant
2316 - CFG_IMMR: Physical address of the Internal Memory.
2317 DO NOT CHANGE unless you know exactly what you're
2318 doing! (11-4) [MPC8xx/82xx systems only]
2320 - CFG_INIT_RAM_ADDR:
2322 Start address of memory area that can be used for
2323 initial data and stack; please note that this must be
2324 writable memory that is working WITHOUT special
2325 initialization, i. e. you CANNOT use normal RAM which
2326 will become available only after programming the
2327 memory controller and running certain initialization
2330 U-Boot uses the following memory types:
2331 - MPC8xx and MPC8260: IMMR (internal memory of the CPU)
2332 - MPC824X: data cache
2333 - PPC4xx: data cache
2335 - CFG_GBL_DATA_OFFSET:
2337 Offset of the initial data structure in the memory
2338 area defined by CFG_INIT_RAM_ADDR. Usually
2339 CFG_GBL_DATA_OFFSET is chosen such that the initial
2340 data is located at the end of the available space
2341 (sometimes written as (CFG_INIT_RAM_END -
2342 CFG_INIT_DATA_SIZE), and the initial stack is just
2343 below that area (growing from (CFG_INIT_RAM_ADDR +
2344 CFG_GBL_DATA_OFFSET) downward.
2347 On the MPC824X (or other systems that use the data
2348 cache for initial memory) the address chosen for
2349 CFG_INIT_RAM_ADDR is basically arbitrary - it must
2350 point to an otherwise UNUSED address space between
2351 the top of RAM and the start of the PCI space.
2353 - CFG_SIUMCR: SIU Module Configuration (11-6)
2355 - CFG_SYPCR: System Protection Control (11-9)
2357 - CFG_TBSCR: Time Base Status and Control (11-26)
2359 - CFG_PISCR: Periodic Interrupt Status and Control (11-31)
2361 - CFG_PLPRCR: PLL, Low-Power, and Reset Control Register (15-30)
2363 - CFG_SCCR: System Clock and reset Control Register (15-27)
2365 - CFG_OR_TIMING_SDRAM:
2369 periodic timer for refresh
2371 - CFG_DER: Debug Event Register (37-47)
2373 - FLASH_BASE0_PRELIM, FLASH_BASE1_PRELIM, CFG_REMAP_OR_AM,
2374 CFG_PRELIM_OR_AM, CFG_OR_TIMING_FLASH, CFG_OR0_REMAP,
2375 CFG_OR0_PRELIM, CFG_BR0_PRELIM, CFG_OR1_REMAP, CFG_OR1_PRELIM,
2377 Memory Controller Definitions: BR0/1 and OR0/1 (FLASH)
2379 - SDRAM_BASE2_PRELIM, SDRAM_BASE3_PRELIM, SDRAM_MAX_SIZE,
2380 CFG_OR_TIMING_SDRAM, CFG_OR2_PRELIM, CFG_BR2_PRELIM,
2381 CFG_OR3_PRELIM, CFG_BR3_PRELIM:
2382 Memory Controller Definitions: BR2/3 and OR2/3 (SDRAM)
2384 - CFG_MAMR_PTA, CFG_MPTPR_2BK_4K, CFG_MPTPR_1BK_4K, CFG_MPTPR_2BK_8K,
2385 CFG_MPTPR_1BK_8K, CFG_MAMR_8COL, CFG_MAMR_9COL:
2386 Machine Mode Register and Memory Periodic Timer
2387 Prescaler definitions (SDRAM timing)
2389 - CFG_I2C_UCODE_PATCH, CFG_I2C_DPMEM_OFFSET [0x1FC0]:
2390 enable I2C microcode relocation patch (MPC8xx);
2391 define relocation offset in DPRAM [DSP2]
2393 - CFG_SMC_UCODE_PATCH, CFG_SMC_DPMEM_OFFSET [0x1FC0]:
2394 enable SMC microcode relocation patch (MPC8xx);
2395 define relocation offset in DPRAM [SMC1]
2397 - CFG_SPI_UCODE_PATCH, CFG_SPI_DPMEM_OFFSET [0x1FC0]:
2398 enable SPI microcode relocation patch (MPC8xx);
2399 define relocation offset in DPRAM [SCC4]
2402 Use OSCM clock mode on MBX8xx board. Be careful,
2403 wrong setting might damage your board. Read
2404 doc/README.MBX before setting this variable!
2406 - CFG_CPM_POST_WORD_ADDR: (MPC8xx, MPC8260 only)
2407 Offset of the bootmode word in DPRAM used by post
2408 (Power On Self Tests). This definition overrides
2409 #define'd default value in commproc.h resp.
2412 - CFG_PCI_SLV_MEM_LOCAL, CFG_PCI_SLV_MEM_BUS, CFG_PICMR0_MASK_ATTRIB,
2413 CFG_PCI_MSTR0_LOCAL, CFG_PCIMSK0_MASK, CFG_PCI_MSTR1_LOCAL,
2414 CFG_PCIMSK1_MASK, CFG_PCI_MSTR_MEM_LOCAL, CFG_PCI_MSTR_MEM_BUS,
2415 CFG_CPU_PCI_MEM_START, CFG_PCI_MSTR_MEM_SIZE, CFG_POCMR0_MASK_ATTRIB,
2416 CFG_PCI_MSTR_MEMIO_LOCAL, CFG_PCI_MSTR_MEMIO_BUS, CPU_PCI_MEMIO_START,
2417 CFG_PCI_MSTR_MEMIO_SIZE, CFG_POCMR1_MASK_ATTRIB, CFG_PCI_MSTR_IO_LOCAL,
2418 CFG_PCI_MSTR_IO_BUS, CFG_CPU_PCI_IO_START, CFG_PCI_MSTR_IO_SIZE,
2419 CFG_POCMR2_MASK_ATTRIB: (MPC826x only)
2420 Overrides the default PCI memory map in cpu/mpc8260/pci.c if set.
2423 Get DDR timing information from an I2C EEPROM. Common
2424 with pluggable memory modules such as SODIMMs
2427 I2C address of the SPD EEPROM
2430 If SPD EEPROM is on an I2C bus other than the first
2431 one, specify here. Note that the value must resolve
2432 to something your driver can deal with.
2434 - CFG_83XX_DDR_USES_CS0
2435 Only for 83xx systems. If specified, then DDR should
2436 be configured using CS0 and CS1 instead of CS2 and CS3.
2438 - CFG_83XX_DDR_USES_CS0
2439 Only for 83xx systems. If specified, then DDR should
2440 be configured using CS0 and CS1 instead of CS2 and CS3.
2442 - CONFIG_ETHER_ON_FEC[12]
2443 Define to enable FEC[12] on a 8xx series processor.
2445 - CONFIG_FEC[12]_PHY
2446 Define to the hardcoded PHY address which corresponds
2447 to the given FEC; i. e.
2448 #define CONFIG_FEC1_PHY 4
2449 means that the PHY with address 4 is connected to FEC1
2451 When set to -1, means to probe for first available.
2453 - CONFIG_FEC[12]_PHY_NORXERR
2454 The PHY does not have a RXERR line (RMII only).
2455 (so program the FEC to ignore it).
2458 Enable RMII mode for all FECs.
2459 Note that this is a global option, we can't
2460 have one FEC in standard MII mode and another in RMII mode.
2462 - CONFIG_CRC32_VERIFY
2463 Add a verify option to the crc32 command.
2466 => crc32 -v <address> <count> <crc32>
2468 Where address/count indicate a memory area
2469 and crc32 is the correct crc32 which the
2473 Add the "loopw" memory command. This only takes effect if
2474 the memory commands are activated globally (CONFIG_CMD_MEM).
2477 Add the "mdc" and "mwc" memory commands. These are cyclic
2482 This command will print 4 bytes (10,11,12,13) each 500 ms.
2484 => mwc.l 100 12345678 10
2485 This command will write 12345678 to address 100 all 10 ms.
2487 This only takes effect if the memory commands are activated
2488 globally (CONFIG_CMD_MEM).
2490 - CONFIG_SKIP_LOWLEVEL_INIT
2491 - CONFIG_SKIP_RELOCATE_UBOOT
2493 [ARM only] If these variables are defined, then
2494 certain low level initializations (like setting up
2495 the memory controller) are omitted and/or U-Boot does
2496 not relocate itself into RAM.
2497 Normally these variables MUST NOT be defined. The
2498 only exception is when U-Boot is loaded (to RAM) by
2499 some other boot loader or by a debugger which
2500 performs these intializations itself.
2503 Building the Software:
2504 ======================
2506 Building U-Boot has been tested in several native build environments
2507 and in many different cross environments. Of course we cannot support
2508 all possibly existing versions of cross development tools in all
2509 (potentially obsolete) versions. In case of tool chain problems we
2510 recommend to use the ELDK (see http://www.denx.de/wiki/DULG/ELDK)
2511 which is extensively used to build and test U-Boot.
2513 If you are not using a native environment, it is assumed that you
2514 have GNU cross compiling tools available in your path. In this case,
2515 you must set the environment variable CROSS_COMPILE in your shell.
2516 Note that no changes to the Makefile or any other source files are
2517 necessary. For example using the ELDK on a 4xx CPU, please enter:
2519 $ CROSS_COMPILE=ppc_4xx-
2520 $ export CROSS_COMPILE
2522 U-Boot is intended to be simple to build. After installing the
2523 sources you must configure U-Boot for one specific board type. This
2528 where "NAME_config" is the name of one of the existing configu-
2529 rations; see the main Makefile for supported names.
2531 Note: for some board special configuration names may exist; check if
2532 additional information is available from the board vendor; for
2533 instance, the TQM823L systems are available without (standard)
2534 or with LCD support. You can select such additional "features"
2535 when chosing the configuration, i. e.
2538 - will configure for a plain TQM823L, i. e. no LCD support
2540 make TQM823L_LCD_config
2541 - will configure for a TQM823L with U-Boot console on LCD
2546 Finally, type "make all", and you should get some working U-Boot
2547 images ready for download to / installation on your system:
2549 - "u-boot.bin" is a raw binary image
2550 - "u-boot" is an image in ELF binary format
2551 - "u-boot.srec" is in Motorola S-Record format
2553 By default the build is performed locally and the objects are saved
2554 in the source directory. One of the two methods can be used to change
2555 this behavior and build U-Boot to some external directory:
2557 1. Add O= to the make command line invocations:
2559 make O=/tmp/build distclean
2560 make O=/tmp/build NAME_config
2561 make O=/tmp/build all
2563 2. Set environment variable BUILD_DIR to point to the desired location:
2565 export BUILD_DIR=/tmp/build
2570 Note that the command line "O=" setting overrides the BUILD_DIR environment
2574 Please be aware that the Makefiles assume you are using GNU make, so
2575 for instance on NetBSD you might need to use "gmake" instead of
2579 If the system board that you have is not listed, then you will need
2580 to port U-Boot to your hardware platform. To do this, follow these
2583 1. Add a new configuration option for your board to the toplevel
2584 "Makefile" and to the "MAKEALL" script, using the existing
2585 entries as examples. Note that here and at many other places
2586 boards and other names are listed in alphabetical sort order. Please
2588 2. Create a new directory to hold your board specific code. Add any
2589 files you need. In your board directory, you will need at least
2590 the "Makefile", a "<board>.c", "flash.c" and "u-boot.lds".
2591 3. Create a new configuration file "include/configs/<board>.h" for
2593 3. If you're porting U-Boot to a new CPU, then also create a new
2594 directory to hold your CPU specific code. Add any files you need.
2595 4. Run "make <board>_config" with your new name.
2596 5. Type "make", and you should get a working "u-boot.srec" file
2597 to be installed on your target system.
2598 6. Debug and solve any problems that might arise.
2599 [Of course, this last step is much harder than it sounds.]
2602 Testing of U-Boot Modifications, Ports to New Hardware, etc.:
2603 ==============================================================
2605 If you have modified U-Boot sources (for instance added a new board
2606 or support for new devices, a new CPU, etc.) you are expected to
2607 provide feedback to the other developers. The feedback normally takes
2608 the form of a "patch", i. e. a context diff against a certain (latest
2609 official or latest in the git repository) version of U-Boot sources.
2611 But before you submit such a patch, please verify that your modifi-
2612 cation did not break existing code. At least make sure that *ALL* of
2613 the supported boards compile WITHOUT ANY compiler warnings. To do so,
2614 just run the "MAKEALL" script, which will configure and build U-Boot
2615 for ALL supported system. Be warned, this will take a while. You can
2616 select which (cross) compiler to use by passing a `CROSS_COMPILE'
2617 environment variable to the script, i. e. to use the ELDK cross tools
2620 CROSS_COMPILE=ppc_8xx- MAKEALL
2622 or to build on a native PowerPC system you can type
2624 CROSS_COMPILE=' ' MAKEALL
2626 When using the MAKEALL script, the default behaviour is to build
2627 U-Boot in the source directory. This location can be changed by
2628 setting the BUILD_DIR environment variable. Also, for each target
2629 built, the MAKEALL script saves two log files (<target>.ERR and
2630 <target>.MAKEALL) in the <source dir>/LOG directory. This default
2631 location can be changed by setting the MAKEALL_LOGDIR environment
2632 variable. For example:
2634 export BUILD_DIR=/tmp/build
2635 export MAKEALL_LOGDIR=/tmp/log
2636 CROSS_COMPILE=ppc_8xx- MAKEALL
2638 With the above settings build objects are saved in the /tmp/build,
2639 log files are saved in the /tmp/log and the source tree remains clean
2640 during the whole build process.
2643 See also "U-Boot Porting Guide" below.
2646 Monitor Commands - Overview:
2647 ============================
2649 go - start application at address 'addr'
2650 run - run commands in an environment variable
2651 bootm - boot application image from memory
2652 bootp - boot image via network using BootP/TFTP protocol
2653 tftpboot- boot image via network using TFTP protocol
2654 and env variables "ipaddr" and "serverip"
2655 (and eventually "gatewayip")
2656 rarpboot- boot image via network using RARP/TFTP protocol
2657 diskboot- boot from IDE devicebootd - boot default, i.e., run 'bootcmd'
2658 loads - load S-Record file over serial line
2659 loadb - load binary file over serial line (kermit mode)
2661 mm - memory modify (auto-incrementing)
2662 nm - memory modify (constant address)
2663 mw - memory write (fill)
2665 cmp - memory compare
2666 crc32 - checksum calculation
2667 imd - i2c memory display
2668 imm - i2c memory modify (auto-incrementing)
2669 inm - i2c memory modify (constant address)
2670 imw - i2c memory write (fill)
2671 icrc32 - i2c checksum calculation
2672 iprobe - probe to discover valid I2C chip addresses
2673 iloop - infinite loop on address range
2674 isdram - print SDRAM configuration information
2675 sspi - SPI utility commands
2676 base - print or set address offset
2677 printenv- print environment variables
2678 setenv - set environment variables
2679 saveenv - save environment variables to persistent storage
2680 protect - enable or disable FLASH write protection
2681 erase - erase FLASH memory
2682 flinfo - print FLASH memory information
2683 bdinfo - print Board Info structure
2684 iminfo - print header information for application image
2685 coninfo - print console devices and informations
2686 ide - IDE sub-system
2687 loop - infinite loop on address range
2688 loopw - infinite write loop on address range
2689 mtest - simple RAM test
2690 icache - enable or disable instruction cache
2691 dcache - enable or disable data cache
2692 reset - Perform RESET of the CPU
2693 echo - echo args to console
2694 version - print monitor version
2695 help - print online help
2696 ? - alias for 'help'
2699 Monitor Commands - Detailed Description:
2700 ========================================
2704 For now: just type "help <command>".
2707 Environment Variables:
2708 ======================
2710 U-Boot supports user configuration using Environment Variables which
2711 can be made persistent by saving to Flash memory.
2713 Environment Variables are set using "setenv", printed using
2714 "printenv", and saved to Flash using "saveenv". Using "setenv"
2715 without a value can be used to delete a variable from the
2716 environment. As long as you don't save the environment you are
2717 working with an in-memory copy. In case the Flash area containing the
2718 environment is erased by accident, a default environment is provided.
2720 Some configuration options can be set using Environment Variables:
2722 baudrate - see CONFIG_BAUDRATE
2724 bootdelay - see CONFIG_BOOTDELAY
2726 bootcmd - see CONFIG_BOOTCOMMAND
2728 bootargs - Boot arguments when booting an RTOS image
2730 bootfile - Name of the image to load with TFTP
2732 autoload - if set to "no" (any string beginning with 'n'),
2733 "bootp" will just load perform a lookup of the
2734 configuration from the BOOTP server, but not try to
2735 load any image using TFTP
2737 autoscript - if set to "yes" commands like "loadb", "loady",
2738 "bootp", "tftpb", "rarpboot" and "nfs" will attempt
2739 to automatically run script images (by internally
2740 calling "autoscript").
2742 autoscript_uname - if script image is in a format (FIT) this
2743 variable is used to get script subimage unit name.
2745 autostart - if set to "yes", an image loaded using the "bootp",
2746 "rarpboot", "tftpboot" or "diskboot" commands will
2747 be automatically started (by internally calling
2750 If set to "no", a standalone image passed to the
2751 "bootm" command will be copied to the load address
2752 (and eventually uncompressed), but NOT be started.
2753 This can be used to load and uncompress arbitrary
2756 i2cfast - (PPC405GP|PPC405EP only)
2757 if set to 'y' configures Linux I2C driver for fast
2758 mode (400kHZ). This environment variable is used in
2759 initialization code. So, for changes to be effective
2760 it must be saved and board must be reset.
2762 initrd_high - restrict positioning of initrd images:
2763 If this variable is not set, initrd images will be
2764 copied to the highest possible address in RAM; this
2765 is usually what you want since it allows for
2766 maximum initrd size. If for some reason you want to
2767 make sure that the initrd image is loaded below the
2768 CFG_BOOTMAPSZ limit, you can set this environment
2769 variable to a value of "no" or "off" or "0".
2770 Alternatively, you can set it to a maximum upper
2771 address to use (U-Boot will still check that it
2772 does not overwrite the U-Boot stack and data).
2774 For instance, when you have a system with 16 MB
2775 RAM, and want to reserve 4 MB from use by Linux,
2776 you can do this by adding "mem=12M" to the value of
2777 the "bootargs" variable. However, now you must make
2778 sure that the initrd image is placed in the first
2779 12 MB as well - this can be done with
2781 setenv initrd_high 00c00000
2783 If you set initrd_high to 0xFFFFFFFF, this is an
2784 indication to U-Boot that all addresses are legal
2785 for the Linux kernel, including addresses in flash
2786 memory. In this case U-Boot will NOT COPY the
2787 ramdisk at all. This may be useful to reduce the
2788 boot time on your system, but requires that this
2789 feature is supported by your Linux kernel.
2791 ipaddr - IP address; needed for tftpboot command
2793 loadaddr - Default load address for commands like "bootp",
2794 "rarpboot", "tftpboot", "loadb" or "diskboot"
2796 loads_echo - see CONFIG_LOADS_ECHO
2798 serverip - TFTP server IP address; needed for tftpboot command
2800 bootretry - see CONFIG_BOOT_RETRY_TIME
2802 bootdelaykey - see CONFIG_AUTOBOOT_DELAY_STR
2804 bootstopkey - see CONFIG_AUTOBOOT_STOP_STR
2806 ethprime - When CONFIG_NET_MULTI is enabled controls which
2807 interface is used first.
2809 ethact - When CONFIG_NET_MULTI is enabled controls which
2810 interface is currently active. For example you
2811 can do the following
2813 => setenv ethact FEC ETHERNET
2814 => ping 192.168.0.1 # traffic sent on FEC ETHERNET
2815 => setenv ethact SCC ETHERNET
2816 => ping 10.0.0.1 # traffic sent on SCC ETHERNET
2818 ethrotate - When set to "no" U-Boot does not go through all
2819 available network interfaces.
2820 It just stays at the currently selected interface.
2822 netretry - When set to "no" each network operation will
2823 either succeed or fail without retrying.
2824 When set to "once" the network operation will
2825 fail when all the available network interfaces
2826 are tried once without success.
2827 Useful on scripts which control the retry operation
2830 npe_ucode - see CONFIG_IXP4XX_NPE_EXT_UCOD
2831 if set load address for the npe microcode
2833 tftpsrcport - If this is set, the value is used for TFTP's
2836 tftpdstport - If this is set, the value is used for TFTP's UDP
2837 destination port instead of the Well Know Port 69.
2839 vlan - When set to a value < 4095 the traffic over
2840 ethernet is encapsulated/received over 802.1q
2843 The following environment variables may be used and automatically
2844 updated by the network boot commands ("bootp" and "rarpboot"),
2845 depending the information provided by your boot server:
2847 bootfile - see above
2848 dnsip - IP address of your Domain Name Server
2849 dnsip2 - IP address of your secondary Domain Name Server
2850 gatewayip - IP address of the Gateway (Router) to use
2851 hostname - Target hostname
2853 netmask - Subnet Mask
2854 rootpath - Pathname of the root filesystem on the NFS server
2855 serverip - see above
2858 There are two special Environment Variables:
2860 serial# - contains hardware identification information such
2861 as type string and/or serial number
2862 ethaddr - Ethernet address
2864 These variables can be set only once (usually during manufacturing of
2865 the board). U-Boot refuses to delete or overwrite these variables
2866 once they have been set once.
2869 Further special Environment Variables:
2871 ver - Contains the U-Boot version string as printed
2872 with the "version" command. This variable is
2873 readonly (see CONFIG_VERSION_VARIABLE).
2876 Please note that changes to some configuration parameters may take
2877 only effect after the next boot (yes, that's just like Windoze :-).
2880 Command Line Parsing:
2881 =====================
2883 There are two different command line parsers available with U-Boot:
2884 the old "simple" one, and the much more powerful "hush" shell:
2886 Old, simple command line parser:
2887 --------------------------------
2889 - supports environment variables (through setenv / saveenv commands)
2890 - several commands on one line, separated by ';'
2891 - variable substitution using "... ${name} ..." syntax
2892 - special characters ('$', ';') can be escaped by prefixing with '\',
2894 setenv bootcmd bootm \${address}
2895 - You can also escape text by enclosing in single apostrophes, for example:
2896 setenv addip 'setenv bootargs $bootargs ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname::off'
2901 - similar to Bourne shell, with control structures like
2902 if...then...else...fi, for...do...done; while...do...done,
2903 until...do...done, ...
2904 - supports environment ("global") variables (through setenv / saveenv
2905 commands) and local shell variables (through standard shell syntax
2906 "name=value"); only environment variables can be used with "run"
2912 (1) If a command line (or an environment variable executed by a "run"
2913 command) contains several commands separated by semicolon, and
2914 one of these commands fails, then the remaining commands will be
2917 (2) If you execute several variables with one call to run (i. e.
2918 calling run with a list af variables as arguments), any failing
2919 command will cause "run" to terminate, i. e. the remaining
2920 variables are not executed.
2922 Note for Redundant Ethernet Interfaces:
2923 =======================================
2925 Some boards come with redundant ethernet interfaces; U-Boot supports
2926 such configurations and is capable of automatic selection of a
2927 "working" interface when needed. MAC assignment works as follows:
2929 Network interfaces are numbered eth0, eth1, eth2, ... Corresponding
2930 MAC addresses can be stored in the environment as "ethaddr" (=>eth0),
2931 "eth1addr" (=>eth1), "eth2addr", ...
2933 If the network interface stores some valid MAC address (for instance
2934 in SROM), this is used as default address if there is NO correspon-
2935 ding setting in the environment; if the corresponding environment
2936 variable is set, this overrides the settings in the card; that means:
2938 o If the SROM has a valid MAC address, and there is no address in the
2939 environment, the SROM's address is used.
2941 o If there is no valid address in the SROM, and a definition in the
2942 environment exists, then the value from the environment variable is
2945 o If both the SROM and the environment contain a MAC address, and
2946 both addresses are the same, this MAC address is used.
2948 o If both the SROM and the environment contain a MAC address, and the
2949 addresses differ, the value from the environment is used and a
2952 o If neither SROM nor the environment contain a MAC address, an error
2959 U-Boot is capable of booting (and performing other auxiliary operations on)
2960 images in two formats:
2962 New uImage format (FIT)
2963 -----------------------
2965 Flexible and powerful format based on Flattened Image Tree -- FIT (similar
2966 to Flattened Device Tree). It allows the use of images with multiple
2967 components (several kernels, ramdisks, etc.), with contents protected by
2968 SHA1, MD5 or CRC32. More details are found in the doc/uImage.FIT directory.
2974 Old image format is based on binary files which can be basically anything,
2975 preceded by a special header; see the definitions in include/image.h for
2976 details; basically, the header defines the following image properties:
2978 * Target Operating System (Provisions for OpenBSD, NetBSD, FreeBSD,
2979 4.4BSD, Linux, SVR4, Esix, Solaris, Irix, SCO, Dell, NCR, VxWorks,
2980 LynxOS, pSOS, QNX, RTEMS, ARTOS;
2981 Currently supported: Linux, NetBSD, VxWorks, QNX, RTEMS, ARTOS, LynxOS).
2982 * Target CPU Architecture (Provisions for Alpha, ARM, AVR32, Intel x86,
2983 IA64, MIPS, NIOS, PowerPC, IBM S390, SuperH, Sparc, Sparc 64 Bit;
2984 Currently supported: ARM, AVR32, Intel x86, MIPS, NIOS, PowerPC).
2985 * Compression Type (uncompressed, gzip, bzip2)
2991 The header is marked by a special Magic Number, and both the header
2992 and the data portions of the image are secured against corruption by
2999 Although U-Boot should support any OS or standalone application
3000 easily, the main focus has always been on Linux during the design of
3003 U-Boot includes many features that so far have been part of some
3004 special "boot loader" code within the Linux kernel. Also, any
3005 "initrd" images to be used are no longer part of one big Linux image;
3006 instead, kernel and "initrd" are separate images. This implementation
3007 serves several purposes:
3009 - the same features can be used for other OS or standalone
3010 applications (for instance: using compressed images to reduce the
3011 Flash memory footprint)
3013 - it becomes much easier to port new Linux kernel versions because
3014 lots of low-level, hardware dependent stuff are done by U-Boot
3016 - the same Linux kernel image can now be used with different "initrd"
3017 images; of course this also means that different kernel images can
3018 be run with the same "initrd". This makes testing easier (you don't
3019 have to build a new "zImage.initrd" Linux image when you just
3020 change a file in your "initrd"). Also, a field-upgrade of the
3021 software is easier now.
3027 Porting Linux to U-Boot based systems:
3028 ---------------------------------------
3030 U-Boot cannot save you from doing all the necessary modifications to
3031 configure the Linux device drivers for use with your target hardware
3032 (no, we don't intend to provide a full virtual machine interface to
3035 But now you can ignore ALL boot loader code (in arch/ppc/mbxboot).
3037 Just make sure your machine specific header file (for instance
3038 include/asm-ppc/tqm8xx.h) includes the same definition of the Board
3039 Information structure as we define in include/u-boot.h, and make
3040 sure that your definition of IMAP_ADDR uses the same value as your
3041 U-Boot configuration in CFG_IMMR.
3044 Configuring the Linux kernel:
3045 -----------------------------
3047 No specific requirements for U-Boot. Make sure you have some root
3048 device (initial ramdisk, NFS) for your target system.
3051 Building a Linux Image:
3052 -----------------------
3054 With U-Boot, "normal" build targets like "zImage" or "bzImage" are
3055 not used. If you use recent kernel source, a new build target
3056 "uImage" will exist which automatically builds an image usable by
3057 U-Boot. Most older kernels also have support for a "pImage" target,
3058 which was introduced for our predecessor project PPCBoot and uses a
3059 100% compatible format.
3068 The "uImage" build target uses a special tool (in 'tools/mkimage') to
3069 encapsulate a compressed Linux kernel image with header information,
3070 CRC32 checksum etc. for use with U-Boot. This is what we are doing:
3072 * build a standard "vmlinux" kernel image (in ELF binary format):
3074 * convert the kernel into a raw binary image:
3076 ${CROSS_COMPILE}-objcopy -O binary \
3077 -R .note -R .comment \
3078 -S vmlinux linux.bin
3080 * compress the binary image:
3084 * package compressed binary image for U-Boot:
3086 mkimage -A ppc -O linux -T kernel -C gzip \
3087 -a 0 -e 0 -n "Linux Kernel Image" \
3088 -d linux.bin.gz uImage
3091 The "mkimage" tool can also be used to create ramdisk images for use
3092 with U-Boot, either separated from the Linux kernel image, or
3093 combined into one file. "mkimage" encapsulates the images with a 64
3094 byte header containing information about target architecture,
3095 operating system, image type, compression method, entry points, time
3096 stamp, CRC32 checksums, etc.
3098 "mkimage" can be called in two ways: to verify existing images and
3099 print the header information, or to build new images.
3101 In the first form (with "-l" option) mkimage lists the information
3102 contained in the header of an existing U-Boot image; this includes
3103 checksum verification:
3105 tools/mkimage -l image
3106 -l ==> list image header information
3108 The second form (with "-d" option) is used to build a U-Boot image
3109 from a "data file" which is used as image payload:
3111 tools/mkimage -A arch -O os -T type -C comp -a addr -e ep \
3112 -n name -d data_file image
3113 -A ==> set architecture to 'arch'
3114 -O ==> set operating system to 'os'
3115 -T ==> set image type to 'type'
3116 -C ==> set compression type 'comp'
3117 -a ==> set load address to 'addr' (hex)
3118 -e ==> set entry point to 'ep' (hex)
3119 -n ==> set image name to 'name'
3120 -d ==> use image data from 'datafile'
3122 Right now, all Linux kernels for PowerPC systems use the same load
3123 address (0x00000000), but the entry point address depends on the
3126 - 2.2.x kernels have the entry point at 0x0000000C,
3127 - 2.3.x and later kernels have the entry point at 0x00000000.
3129 So a typical call to build a U-Boot image would read:
3131 -> tools/mkimage -n '2.4.4 kernel for TQM850L' \
3132 > -A ppc -O linux -T kernel -C gzip -a 0 -e 0 \
3133 > -d /opt/elsk/ppc_8xx/usr/src/linux-2.4.4/arch/ppc/coffboot/vmlinux.gz \
3134 > examples/uImage.TQM850L
3135 Image Name: 2.4.4 kernel for TQM850L
3136 Created: Wed Jul 19 02:34:59 2000
3137 Image Type: PowerPC Linux Kernel Image (gzip compressed)
3138 Data Size: 335725 Bytes = 327.86 kB = 0.32 MB
3139 Load Address: 0x00000000
3140 Entry Point: 0x00000000
3142 To verify the contents of the image (or check for corruption):
3144 -> tools/mkimage -l examples/uImage.TQM850L
3145 Image Name: 2.4.4 kernel for TQM850L
3146 Created: Wed Jul 19 02:34:59 2000
3147 Image Type: PowerPC Linux Kernel Image (gzip compressed)
3148 Data Size: 335725 Bytes = 327.86 kB = 0.32 MB
3149 Load Address: 0x00000000
3150 Entry Point: 0x00000000
3152 NOTE: for embedded systems where boot time is critical you can trade
3153 speed for memory and install an UNCOMPRESSED image instead: this
3154 needs more space in Flash, but boots much faster since it does not
3155 need to be uncompressed:
3157 -> gunzip /opt/elsk/ppc_8xx/usr/src/linux-2.4.4/arch/ppc/coffboot/vmlinux.gz
3158 -> tools/mkimage -n '2.4.4 kernel for TQM850L' \
3159 > -A ppc -O linux -T kernel -C none -a 0 -e 0 \
3160 > -d /opt/elsk/ppc_8xx/usr/src/linux-2.4.4/arch/ppc/coffboot/vmlinux \
3161 > examples/uImage.TQM850L-uncompressed
3162 Image Name: 2.4.4 kernel for TQM850L
3163 Created: Wed Jul 19 02:34:59 2000
3164 Image Type: PowerPC Linux Kernel Image (uncompressed)
3165 Data Size: 792160 Bytes = 773.59 kB = 0.76 MB
3166 Load Address: 0x00000000
3167 Entry Point: 0x00000000
3170 Similar you can build U-Boot images from a 'ramdisk.image.gz' file
3171 when your kernel is intended to use an initial ramdisk:
3173 -> tools/mkimage -n 'Simple Ramdisk Image' \
3174 > -A ppc -O linux -T ramdisk -C gzip \
3175 > -d /LinuxPPC/images/SIMPLE-ramdisk.image.gz examples/simple-initrd
3176 Image Name: Simple Ramdisk Image
3177 Created: Wed Jan 12 14:01:50 2000
3178 Image Type: PowerPC Linux RAMDisk Image (gzip compressed)
3179 Data Size: 566530 Bytes = 553.25 kB = 0.54 MB
3180 Load Address: 0x00000000
3181 Entry Point: 0x00000000
3184 Installing a Linux Image:
3185 -------------------------
3187 To downloading a U-Boot image over the serial (console) interface,
3188 you must convert the image to S-Record format:
3190 objcopy -I binary -O srec examples/image examples/image.srec
3192 The 'objcopy' does not understand the information in the U-Boot
3193 image header, so the resulting S-Record file will be relative to
3194 address 0x00000000. To load it to a given address, you need to
3195 specify the target address as 'offset' parameter with the 'loads'
3198 Example: install the image to address 0x40100000 (which on the
3199 TQM8xxL is in the first Flash bank):
3201 => erase 40100000 401FFFFF
3207 ## Ready for S-Record download ...
3208 ~>examples/image.srec
3209 1 2 3 4 5 6 7 8 9 10 11 12 13 ...
3211 15989 15990 15991 15992
3212 [file transfer complete]
3214 ## Start Addr = 0x00000000
3217 You can check the success of the download using the 'iminfo' command;
3218 this includes a checksum verification so you can be sure no data
3219 corruption happened:
3223 ## Checking Image at 40100000 ...
3224 Image Name: 2.2.13 for initrd on TQM850L
3225 Image Type: PowerPC Linux Kernel Image (gzip compressed)
3226 Data Size: 335725 Bytes = 327 kB = 0 MB
3227 Load Address: 00000000
3228 Entry Point: 0000000c
3229 Verifying Checksum ... OK
3235 The "bootm" command is used to boot an application that is stored in
3236 memory (RAM or Flash). In case of a Linux kernel image, the contents
3237 of the "bootargs" environment variable is passed to the kernel as
3238 parameters. You can check and modify this variable using the
3239 "printenv" and "setenv" commands:
3242 => printenv bootargs
3243 bootargs=root=/dev/ram
3245 => setenv bootargs root=/dev/nfs rw nfsroot=10.0.0.2:/LinuxPPC nfsaddrs=10.0.0.99:10.0.0.2
3247 => printenv bootargs
3248 bootargs=root=/dev/nfs rw nfsroot=10.0.0.2:/LinuxPPC nfsaddrs=10.0.0.99:10.0.0.2
3251 ## Booting Linux kernel at 40020000 ...
3252 Image Name: 2.2.13 for NFS on TQM850L
3253 Image Type: PowerPC Linux Kernel Image (gzip compressed)
3254 Data Size: 381681 Bytes = 372 kB = 0 MB
3255 Load Address: 00000000
3256 Entry Point: 0000000c
3257 Verifying Checksum ... OK
3258 Uncompressing Kernel Image ... OK
3259 Linux version 2.2.13 (wd@denx.local.net) (gcc version 2.95.2 19991024 (release)) #1 Wed Jul 19 02:35:17 MEST 2000
3260 Boot arguments: root=/dev/nfs rw nfsroot=10.0.0.2:/LinuxPPC nfsaddrs=10.0.0.99:10.0.0.2
3261 time_init: decrementer frequency = 187500000/60
3262 Calibrating delay loop... 49.77 BogoMIPS
3263 Memory: 15208k available (700k kernel code, 444k data, 32k init) [c0000000,c1000000]
3266 If you want to boot a Linux kernel with initial ram disk, you pass
3267 the memory addresses of both the kernel and the initrd image (PPBCOOT
3268 format!) to the "bootm" command:
3270 => imi 40100000 40200000
3272 ## Checking Image at 40100000 ...
3273 Image Name: 2.2.13 for initrd on TQM850L
3274 Image Type: PowerPC Linux Kernel Image (gzip compressed)
3275 Data Size: 335725 Bytes = 327 kB = 0 MB
3276 Load Address: 00000000
3277 Entry Point: 0000000c
3278 Verifying Checksum ... OK
3280 ## Checking Image at 40200000 ...
3281 Image Name: Simple Ramdisk Image
3282 Image Type: PowerPC Linux RAMDisk Image (gzip compressed)
3283 Data Size: 566530 Bytes = 553 kB = 0 MB
3284 Load Address: 00000000
3285 Entry Point: 00000000
3286 Verifying Checksum ... OK
3288 => bootm 40100000 40200000
3289 ## Booting Linux kernel at 40100000 ...
3290 Image Name: 2.2.13 for initrd on TQM850L
3291 Image Type: PowerPC Linux Kernel Image (gzip compressed)
3292 Data Size: 335725 Bytes = 327 kB = 0 MB
3293 Load Address: 00000000
3294 Entry Point: 0000000c
3295 Verifying Checksum ... OK
3296 Uncompressing Kernel Image ... OK
3297 ## Loading RAMDisk Image at 40200000 ...
3298 Image Name: Simple Ramdisk Image
3299 Image Type: PowerPC Linux RAMDisk Image (gzip compressed)
3300 Data Size: 566530 Bytes = 553 kB = 0 MB
3301 Load Address: 00000000
3302 Entry Point: 00000000
3303 Verifying Checksum ... OK
3304 Loading Ramdisk ... OK
3305 Linux version 2.2.13 (wd@denx.local.net) (gcc version 2.95.2 19991024 (release)) #1 Wed Jul 19 02:32:08 MEST 2000
3306 Boot arguments: root=/dev/ram
3307 time_init: decrementer frequency = 187500000/60
3308 Calibrating delay loop... 49.77 BogoMIPS
3310 RAMDISK: Compressed image found at block 0
3311 VFS: Mounted root (ext2 filesystem).
3315 Boot Linux and pass a flat device tree:
3318 First, U-Boot must be compiled with the appropriate defines. See the section
3319 titled "Linux Kernel Interface" above for a more in depth explanation. The
3320 following is an example of how to start a kernel and pass an updated
3326 oft=oftrees/mpc8540ads.dtb
3327 => tftp $oftaddr $oft
3328 Speed: 1000, full duplex
3330 TFTP from server 192.168.1.1; our IP address is 192.168.1.101
3331 Filename 'oftrees/mpc8540ads.dtb'.
3332 Load address: 0x300000
3335 Bytes transferred = 4106 (100a hex)
3336 => tftp $loadaddr $bootfile
3337 Speed: 1000, full duplex
3339 TFTP from server 192.168.1.1; our IP address is 192.168.1.2
3341 Load address: 0x200000
3342 Loading:############
3344 Bytes transferred = 1029407 (fb51f hex)
3349 => bootm $loadaddr - $oftaddr
3350 ## Booting image at 00200000 ...
3351 Image Name: Linux-2.6.17-dirty
3352 Image Type: PowerPC Linux Kernel Image (gzip compressed)
3353 Data Size: 1029343 Bytes = 1005.2 kB
3354 Load Address: 00000000
3355 Entry Point: 00000000
3356 Verifying Checksum ... OK
3357 Uncompressing Kernel Image ... OK
3358 Booting using flat device tree at 0x300000
3359 Using MPC85xx ADS machine description
3360 Memory CAM mapping: CAM0=256Mb, CAM1=256Mb, CAM2=0Mb residual: 0Mb
3364 More About U-Boot Image Types:
3365 ------------------------------
3367 U-Boot supports the following image types:
3369 "Standalone Programs" are directly runnable in the environment
3370 provided by U-Boot; it is expected that (if they behave
3371 well) you can continue to work in U-Boot after return from
3372 the Standalone Program.
3373 "OS Kernel Images" are usually images of some Embedded OS which
3374 will take over control completely. Usually these programs
3375 will install their own set of exception handlers, device
3376 drivers, set up the MMU, etc. - this means, that you cannot
3377 expect to re-enter U-Boot except by resetting the CPU.
3378 "RAMDisk Images" are more or less just data blocks, and their
3379 parameters (address, size) are passed to an OS kernel that is
3381 "Multi-File Images" contain several images, typically an OS
3382 (Linux) kernel image and one or more data images like
3383 RAMDisks. This construct is useful for instance when you want
3384 to boot over the network using BOOTP etc., where the boot
3385 server provides just a single image file, but you want to get
3386 for instance an OS kernel and a RAMDisk image.
3388 "Multi-File Images" start with a list of image sizes, each
3389 image size (in bytes) specified by an "uint32_t" in network
3390 byte order. This list is terminated by an "(uint32_t)0".
3391 Immediately after the terminating 0 follow the images, one by
3392 one, all aligned on "uint32_t" boundaries (size rounded up to
3393 a multiple of 4 bytes).
3395 "Firmware Images" are binary images containing firmware (like
3396 U-Boot or FPGA images) which usually will be programmed to
3399 "Script files" are command sequences that will be executed by
3400 U-Boot's command interpreter; this feature is especially
3401 useful when you configure U-Boot to use a real shell (hush)
3402 as command interpreter.
3408 One of the features of U-Boot is that you can dynamically load and
3409 run "standalone" applications, which can use some resources of
3410 U-Boot like console I/O functions or interrupt services.
3412 Two simple examples are included with the sources:
3417 'examples/hello_world.c' contains a small "Hello World" Demo
3418 application; it is automatically compiled when you build U-Boot.
3419 It's configured to run at address 0x00040004, so you can play with it
3423 ## Ready for S-Record download ...
3424 ~>examples/hello_world.srec
3425 1 2 3 4 5 6 7 8 9 10 11 ...
3426 [file transfer complete]
3428 ## Start Addr = 0x00040004
3430 => go 40004 Hello World! This is a test.
3431 ## Starting application at 0x00040004 ...
3442 Hit any key to exit ...
3444 ## Application terminated, rc = 0x0
3446 Another example, which demonstrates how to register a CPM interrupt
3447 handler with the U-Boot code, can be found in 'examples/timer.c'.
3448 Here, a CPM timer is set up to generate an interrupt every second.
3449 The interrupt service routine is trivial, just printing a '.'
3450 character, but this is just a demo program. The application can be
3451 controlled by the following keys:
3453 ? - print current values og the CPM Timer registers
3454 b - enable interrupts and start timer
3455 e - stop timer and disable interrupts
3456 q - quit application
3459 ## Ready for S-Record download ...
3460 ~>examples/timer.srec
3461 1 2 3 4 5 6 7 8 9 10 11 ...
3462 [file transfer complete]
3464 ## Start Addr = 0x00040004
3467 ## Starting application at 0x00040004 ...
3470 tgcr @ 0xfff00980, tmr @ 0xfff00990, trr @ 0xfff00994, tcr @ 0xfff00998, tcn @ 0xfff0099c, ter @ 0xfff009b0
3473 [q, b, e, ?] Set interval 1000000 us
3476 [q, b, e, ?] ........
3477 tgcr=0x1, tmr=0xff1c, trr=0x3d09, tcr=0x0, tcn=0xef6, ter=0x0
3480 tgcr=0x1, tmr=0xff1c, trr=0x3d09, tcr=0x0, tcn=0x2ad4, ter=0x0
3483 tgcr=0x1, tmr=0xff1c, trr=0x3d09, tcr=0x0, tcn=0x1efc, ter=0x0
3486 tgcr=0x1, tmr=0xff1c, trr=0x3d09, tcr=0x0, tcn=0x169d, ter=0x0
3488 [q, b, e, ?] ...Stopping timer
3490 [q, b, e, ?] ## Application terminated, rc = 0x0
3496 Over time, many people have reported problems when trying to use the
3497 "minicom" terminal emulation program for serial download. I (wd)
3498 consider minicom to be broken, and recommend not to use it. Under
3499 Unix, I recommend to use C-Kermit for general purpose use (and
3500 especially for kermit binary protocol download ("loadb" command), and
3501 use "cu" for S-Record download ("loads" command).
3503 Nevertheless, if you absolutely want to use it try adding this
3504 configuration to your "File transfer protocols" section:
3506 Name Program Name U/D FullScr IO-Red. Multi
3507 X kermit /usr/bin/kermit -i -l %l -s Y U Y N N
3508 Y kermit /usr/bin/kermit -i -l %l -r N D Y N N
3514 Starting at version 0.9.2, U-Boot supports NetBSD both as host
3515 (build U-Boot) and target system (boots NetBSD/mpc8xx).
3517 Building requires a cross environment; it is known to work on
3518 NetBSD/i386 with the cross-powerpc-netbsd-1.3 package (you will also
3519 need gmake since the Makefiles are not compatible with BSD make).
3520 Note that the cross-powerpc package does not install include files;
3521 attempting to build U-Boot will fail because <machine/ansi.h> is
3522 missing. This file has to be installed and patched manually:
3524 # cd /usr/pkg/cross/powerpc-netbsd/include
3526 # ln -s powerpc machine
3527 # cp /usr/src/sys/arch/powerpc/include/ansi.h powerpc/ansi.h
3528 # ${EDIT} powerpc/ansi.h ## must remove __va_list, _BSD_VA_LIST
3530 Native builds *don't* work due to incompatibilities between native
3531 and U-Boot include files.
3533 Booting assumes that (the first part of) the image booted is a
3534 stage-2 loader which in turn loads and then invokes the kernel
3535 proper. Loader sources will eventually appear in the NetBSD source
3536 tree (probably in sys/arc/mpc8xx/stand/u-boot_stage2/); in the
3537 meantime, see ftp://ftp.denx.de/pub/u-boot/ppcboot_stage2.tar.gz
3540 Implementation Internals:
3541 =========================
3543 The following is not intended to be a complete description of every
3544 implementation detail. However, it should help to understand the
3545 inner workings of U-Boot and make it easier to port it to custom
3549 Initial Stack, Global Data:
3550 ---------------------------
3552 The implementation of U-Boot is complicated by the fact that U-Boot
3553 starts running out of ROM (flash memory), usually without access to
3554 system RAM (because the memory controller is not initialized yet).
3555 This means that we don't have writable Data or BSS segments, and BSS
3556 is not initialized as zero. To be able to get a C environment working
3557 at all, we have to allocate at least a minimal stack. Implementation
3558 options for this are defined and restricted by the CPU used: Some CPU
3559 models provide on-chip memory (like the IMMR area on MPC8xx and
3560 MPC826x processors), on others (parts of) the data cache can be
3561 locked as (mis-) used as memory, etc.
3563 Chris Hallinan posted a good summary of these issues to the
3564 u-boot-users mailing list:
3566 Subject: RE: [U-Boot-Users] RE: More On Memory Bank x (nothingness)?
3567 From: "Chris Hallinan" <clh@net1plus.com>
3568 Date: Mon, 10 Feb 2003 16:43:46 -0500 (22:43 MET)
3571 Correct me if I'm wrong, folks, but the way I understand it
3572 is this: Using DCACHE as initial RAM for Stack, etc, does not
3573 require any physical RAM backing up the cache. The cleverness
3574 is that the cache is being used as a temporary supply of
3575 necessary storage before the SDRAM controller is setup. It's
3576 beyond the scope of this list to expain the details, but you
3577 can see how this works by studying the cache architecture and
3578 operation in the architecture and processor-specific manuals.
3580 OCM is On Chip Memory, which I believe the 405GP has 4K. It
3581 is another option for the system designer to use as an
3582 initial stack/ram area prior to SDRAM being available. Either
3583 option should work for you. Using CS 4 should be fine if your
3584 board designers haven't used it for something that would
3585 cause you grief during the initial boot! It is frequently not
3588 CFG_INIT_RAM_ADDR should be somewhere that won't interfere
3589 with your processor/board/system design. The default value
3590 you will find in any recent u-boot distribution in
3591 walnut.h should work for you. I'd set it to a value larger
3592 than your SDRAM module. If you have a 64MB SDRAM module, set
3593 it above 400_0000. Just make sure your board has no resources
3594 that are supposed to respond to that address! That code in
3595 start.S has been around a while and should work as is when
3596 you get the config right.
3601 It is essential to remember this, since it has some impact on the C
3602 code for the initialization procedures:
3604 * Initialized global data (data segment) is read-only. Do not attempt
3607 * Do not use any unitialized global data (or implicitely initialized
3608 as zero data - BSS segment) at all - this is undefined, initiali-
3609 zation is performed later (when relocating to RAM).
3611 * Stack space is very limited. Avoid big data buffers or things like
3614 Having only the stack as writable memory limits means we cannot use
3615 normal global data to share information beween the code. But it
3616 turned out that the implementation of U-Boot can be greatly
3617 simplified by making a global data structure (gd_t) available to all
3618 functions. We could pass a pointer to this data as argument to _all_
3619 functions, but this would bloat the code. Instead we use a feature of
3620 the GCC compiler (Global Register Variables) to share the data: we
3621 place a pointer (gd) to the global data into a register which we
3622 reserve for this purpose.
3624 When choosing a register for such a purpose we are restricted by the
3625 relevant (E)ABI specifications for the current architecture, and by
3626 GCC's implementation.
3628 For PowerPC, the following registers have specific use:
3630 R2: reserved for system use
3631 R3-R4: parameter passing and return values
3632 R5-R10: parameter passing
3633 R13: small data area pointer
3637 (U-Boot also uses R14 as internal GOT pointer.)
3639 ==> U-Boot will use R2 to hold a pointer to the global data
3641 Note: on PPC, we could use a static initializer (since the
3642 address of the global data structure is known at compile time),
3643 but it turned out that reserving a register results in somewhat
3644 smaller code - although the code savings are not that big (on
3645 average for all boards 752 bytes for the whole U-Boot image,
3646 624 text + 127 data).
3648 On Blackfin, the normal C ABI (except for P5) is followed as documented here:
3649 http://docs.blackfin.uclinux.org/doku.php?id=application_binary_interface
3651 ==> U-Boot will use P5 to hold a pointer to the global data
3653 On ARM, the following registers are used:
3655 R0: function argument word/integer result
3656 R1-R3: function argument word
3658 R10: stack limit (used only if stack checking if enabled)
3659 R11: argument (frame) pointer
3660 R12: temporary workspace
3663 R15: program counter
3665 ==> U-Boot will use R8 to hold a pointer to the global data
3667 NOTE: DECLARE_GLOBAL_DATA_PTR must be used with file-global scope,
3668 or current versions of GCC may "optimize" the code too much.
3673 U-Boot runs in system state and uses physical addresses, i.e. the
3674 MMU is not used either for address mapping nor for memory protection.
3676 The available memory is mapped to fixed addresses using the memory
3677 controller. In this process, a contiguous block is formed for each
3678 memory type (Flash, SDRAM, SRAM), even when it consists of several
3679 physical memory banks.
3681 U-Boot is installed in the first 128 kB of the first Flash bank (on
3682 TQM8xxL modules this is the range 0x40000000 ... 0x4001FFFF). After
3683 booting and sizing and initializing DRAM, the code relocates itself
3684 to the upper end of DRAM. Immediately below the U-Boot code some
3685 memory is reserved for use by malloc() [see CFG_MALLOC_LEN
3686 configuration setting]. Below that, a structure with global Board
3687 Info data is placed, followed by the stack (growing downward).
3689 Additionally, some exception handler code is copied to the low 8 kB
3690 of DRAM (0x00000000 ... 0x00001FFF).
3692 So a typical memory configuration with 16 MB of DRAM could look like
3695 0x0000 0000 Exception Vector code
3698 0x0000 2000 Free for Application Use
3704 0x00FB FF20 Monitor Stack (Growing downward)
3705 0x00FB FFAC Board Info Data and permanent copy of global data
3706 0x00FC 0000 Malloc Arena
3709 0x00FE 0000 RAM Copy of Monitor Code
3710 ... eventually: LCD or video framebuffer
3711 ... eventually: pRAM (Protected RAM - unchanged by reset)
3712 0x00FF FFFF [End of RAM]
3715 System Initialization:
3716 ----------------------
3718 In the reset configuration, U-Boot starts at the reset entry point
3719 (on most PowerPC systens at address 0x00000100). Because of the reset
3720 configuration for CS0# this is a mirror of the onboard Flash memory.
3721 To be able to re-map memory U-Boot then jumps to its link address.
3722 To be able to implement the initialization code in C, a (small!)
3723 initial stack is set up in the internal Dual Ported RAM (in case CPUs
3724 which provide such a feature like MPC8xx or MPC8260), or in a locked
3725 part of the data cache. After that, U-Boot initializes the CPU core,
3726 the caches and the SIU.
3728 Next, all (potentially) available memory banks are mapped using a
3729 preliminary mapping. For example, we put them on 512 MB boundaries
3730 (multiples of 0x20000000: SDRAM on 0x00000000 and 0x20000000, Flash
3731 on 0x40000000 and 0x60000000, SRAM on 0x80000000). Then UPM A is
3732 programmed for SDRAM access. Using the temporary configuration, a
3733 simple memory test is run that determines the size of the SDRAM
3736 When there is more than one SDRAM bank, and the banks are of
3737 different size, the largest is mapped first. For equal size, the first
3738 bank (CS2#) is mapped first. The first mapping is always for address
3739 0x00000000, with any additional banks following immediately to create
3740 contiguous memory starting from 0.
3742 Then, the monitor installs itself at the upper end of the SDRAM area
3743 and allocates memory for use by malloc() and for the global Board
3744 Info data; also, the exception vector code is copied to the low RAM
3745 pages, and the final stack is set up.
3747 Only after this relocation will you have a "normal" C environment;
3748 until that you are restricted in several ways, mostly because you are
3749 running from ROM, and because the code will have to be relocated to a
3753 U-Boot Porting Guide:
3754 ----------------------
3756 [Based on messages by Jerry Van Baren in the U-Boot-Users mailing
3760 int main (int argc, char *argv[])
3762 sighandler_t no_more_time;
3764 signal (SIGALRM, no_more_time);
3765 alarm (PROJECT_DEADLINE - toSec (3 * WEEK));
3767 if (available_money > available_manpower) {
3768 pay consultant to port U-Boot;
3772 Download latest U-Boot source;
3774 Subscribe to u-boot-users mailing list;
3777 email ("Hi, I am new to U-Boot, how do I get started?");
3781 Read the README file in the top level directory;
3782 Read http://www.denx.de/twiki/bin/view/DULG/Manual ;
3783 Read the source, Luke;
3786 if (available_money > toLocalCurrency ($2500)) {
3789 Add a lot of aggravation and time;
3792 Create your own board support subdirectory;
3794 Create your own board config file;
3798 Add / modify source code;
3802 email ("Hi, I am having problems...");
3804 Send patch file to Wolfgang;
3809 void no_more_time (int sig)
3818 All contributions to U-Boot should conform to the Linux kernel
3819 coding style; see the file "Documentation/CodingStyle" and the script
3820 "scripts/Lindent" in your Linux kernel source directory. In sources
3821 originating from U-Boot a style corresponding to "Lindent -pcs" (adding
3822 spaces before parameters to function calls) is actually used.
3824 Source files originating from a different project (for example the
3825 MTD subsystem) are generally exempt from these guidelines and are not
3826 reformated to ease subsequent migration to newer versions of those
3829 Please note that U-Boot is implemented in C (and to some small parts in
3830 Assembler); no C++ is used, so please do not use C++ style comments (//)
3833 Please also stick to the following formatting rules:
3834 - remove any trailing white space
3835 - use TAB characters for indentation, not spaces
3836 - make sure NOT to use DOS '\r\n' line feeds
3837 - do not add more than 2 empty lines to source files
3838 - do not add trailing empty lines to source files
3840 Submissions which do not conform to the standards may be returned
3841 with a request to reformat the changes.
3847 Since the number of patches for U-Boot is growing, we need to
3848 establish some rules. Submissions which do not conform to these rules
3849 may be rejected, even when they contain important and valuable stuff.
3851 Patches shall be sent to the u-boot-users mailing list.
3853 Please see http://www.denx.de/wiki/UBoot/Patches for details.
3855 When you send a patch, please include the following information with
3858 * For bug fixes: a description of the bug and how your patch fixes
3859 this bug. Please try to include a way of demonstrating that the
3860 patch actually fixes something.
3862 * For new features: a description of the feature and your
3865 * A CHANGELOG entry as plaintext (separate from the patch)
3867 * For major contributions, your entry to the CREDITS file
3869 * When you add support for a new board, don't forget to add this
3870 board to the MAKEALL script, too.
3872 * If your patch adds new configuration options, don't forget to
3873 document these in the README file.
3875 * The patch itself. If you are using git (which is *strongly*
3876 recommended) you can easily generate the patch using the
3877 "git-format-patch". If you then use "git-send-email" to send it to
3878 the U-Boot mailing list, you will avoid most of the common problems
3879 with some other mail clients.
3881 If you cannot use git, use "diff -purN OLD NEW". If your version of
3882 diff does not support these options, then get the latest version of
3885 The current directory when running this command shall be the parent
3886 directory of the U-Boot source tree (i. e. please make sure that
3887 your patch includes sufficient directory information for the
3890 We prefer patches as plain text. MIME attachments are discouraged,
3891 and compressed attachments must not be used.
3893 * If one logical set of modifications affects or creates several
3894 files, all these changes shall be submitted in a SINGLE patch file.
3896 * Changesets that contain different, unrelated modifications shall be
3897 submitted as SEPARATE patches, one patch per changeset.
3902 * Before sending the patch, run the MAKEALL script on your patched
3903 source tree and make sure that no errors or warnings are reported
3904 for any of the boards.
3906 * Keep your modifications to the necessary minimum: A patch
3907 containing several unrelated changes or arbitrary reformats will be
3908 returned with a request to re-formatting / split it.
3910 * If you modify existing code, make sure that your new code does not
3911 add to the memory footprint of the code ;-) Small is beautiful!
3912 When adding new features, these should compile conditionally only
3913 (using #ifdef), and the resulting code with the new feature
3914 disabled must not need more memory than the old code without your
3917 * Remember that there is a size limit of 40 kB per message on the
3918 u-boot-users mailing list. Bigger patches will be moderated. If
3919 they are reasonable and not bigger than 100 kB, they will be
3920 acknowledged. Even bigger patches should be avoided.
projects / u-boot / blob