git.sur5r.net Git - u-boot/blob - arch/arm/dts/tegra124-nyan.dtsi

   1 #include <dt-bindings/input/input.h>
   2 #include "tegra124.dtsi"
   3
   4 / {
   5         aliases {
   6                 rtc0 = "/i2c@0,7000d000/pmic@40";
   7                 rtc1 = "/rtc@0,7000e000";
   8                 serial0 = &uarta;
   9         };
  10
  11         memory {
  12                 reg = <0x80000000 0x80000000>;
  13         };
  14
  15         host1x@50000000 {
  16                 hdmi@54280000 {
  17                         status = "okay";
  18
  19                         vdd-supply = <&vdd_3v3_hdmi>;
  20                         pll-supply = <&vdd_hdmi_pll>;
  21                         hdmi-supply = <&vdd_5v0_hdmi>;
  22
  23                         nvidia,ddc-i2c-bus = <&hdmi_ddc>;
  24                         nvidia,hpd-gpio =
  25                                 <&gpio TEGRA_GPIO(N, 7) GPIO_ACTIVE_HIGH>;
  26                 };
  27
  28                 sor@54540000 {
  29                         status = "okay";
  30
  31                         nvidia,dpaux = <&dpaux>;
  32                         nvidia,panel = <&panel>;
  33                 };
  34
  35                 dpaux@545c0000 {
  36                         vdd-supply = <&vdd_3v3_panel>;
  37                         status = "okay";
  38                 };
  39         };
  40
  41         serial@70006000 {
  42                 /* Debug connector on the bottom of the board near SD card. */
  43                 status = "okay";
  44         };
  45
  46         pwm@7000a000 {
  47                 status = "okay";
  48         };
  49
  50         i2c@7000c000 {
  51                 status = "okay";
  52                 clock-frequency = <100000>;
  53
  54                 acodec: audio-codec@10 {
  55                         compatible = "maxim,max98090";
  56                         reg = <0x10>;
  57                         interrupt-parent = <&gpio>;
  58                         interrupts = <TEGRA_GPIO(H, 4) GPIO_ACTIVE_HIGH>;
  59                 };
  60
  61                 temperature-sensor@4c {
  62                         compatible = "ti,tmp451";
  63                         reg = <0x4c>;
  64                         interrupt-parent = <&gpio>;
  65                         interrupts = <TEGRA_GPIO(I, 6) IRQ_TYPE_LEVEL_LOW>;
  66
  67                         #thermal-sensor-cells = <1>;
  68                 };
  69         };
  70
  71         i2c@7000c400 {
  72                 status = "okay";
  73                 clock-frequency = <100000>;
  74
  75                 trackpad@15 {
  76                         compatible = "elan,ekth3000";
  77                         reg = <0x15>;
  78                         interrupt-parent = <&gpio>;
  79                         interrupts = <TEGRA_GPIO(W, 3) IRQ_TYPE_EDGE_FALLING>;
  80                         wakeup-source;
  81                 };
  82         };
  83
  84         i2c@7000c500 {
  85                 status = "okay";
  86                 clock-frequency = <400000>;
  87
  88                 tpm@20 {
  89                         compatible = "infineon,slb9645tt";
  90                         reg = <0x20>;
  91                 };
  92         };
  93
  94         hdmi_ddc: i2c@7000c700 {
  95                 status = "okay";
  96                 clock-frequency = <100000>;
  97         };
  98
  99         i2c@7000d000 {
 100                 status = "okay";
 101                 clock-frequency = <400000>;
 102
 103                 pmic: pmic@40 {
 104                         compatible = "ams,as3722";
 105                         reg = <0x40>;
 106                         interrupts = <0 86 IRQ_TYPE_LEVEL_HIGH>;
 107
 108                         ams,system-power-controller;
 109
 110                         #interrupt-cells = <2>;
 111                         interrupt-controller;
 112
 113                         gpio-controller;
 114                         #gpio-cells = <2>;
 115
 116                         pinctrl-names = "default";
 117                         pinctrl-0 = <&as3722_default>;
 118
 119                         as3722_default: pinmux {
 120                                 gpio0 {
 121                                         pins = "gpio0";
 122                                         function = "gpio";
 123                                         bias-pull-down;
 124                                 };
 125
 126                                 gpio1 {
 127                                         pins = "gpio1";
 128                                         function = "gpio";
 129                                         bias-pull-up;
 130                                 };
 131
 132                                 gpio2_4_7 {
 133                                         pins = "gpio2", "gpio4", "gpio7";
 134                                         function = "gpio";
 135                                         bias-pull-up;
 136                                 };
 137
 138                                 gpio3_6 {
 139                                         pins = "gpio3", "gpio6";
 140                                         bias-high-impedance;
 141                                 };
 142
 143                                 gpio5 {
 144                                         pins = "gpio5";
 145                                         function = "clk32k-out";
 146                                         bias-pull-down;
 147                                 };
 148                         };
 149
 150                         regulators {
 151                                 vsup-sd2-supply = <&vdd_5v0_sys>;
 152                                 vsup-sd3-supply = <&vdd_5v0_sys>;
 153                                 vsup-sd4-supply = <&vdd_5v0_sys>;
 154                                 vsup-sd5-supply = <&vdd_5v0_sys>;
 155                                 vin-ldo0-supply = <&vdd_1v35_lp0>;
 156                                 vin-ldo1-6-supply = <&vdd_3v3_run>;
 157                                 vin-ldo2-5-7-supply = <&vddio_1v8>;
 158                                 vin-ldo3-4-supply = <&vdd_3v3_sys>;
 159                                 vin-ldo9-10-supply = <&vdd_5v0_sys>;
 160                                 vin-ldo11-supply = <&vdd_3v3_run>;
 161
 162                                 vdd_cpu: sd0 {
 163                                         regulator-name = "+VDD_CPU_AP";
 164                                         regulator-min-microvolt = <700000>;
 165                                         regulator-max-microvolt = <1350000>;
 166                                         regulator-min-microamp = <3500000>;
 167                                         regulator-max-microamp = <3500000>;
 168                                         regulator-always-on;
 169                                         regulator-boot-on;
 170                                         ams,ext-control = <2>;
 171                                 };
 172
 173                                 sd1 {
 174                                         regulator-name = "+VDD_CORE";
 175                                         regulator-min-microvolt = <700000>;
 176                                         regulator-max-microvolt = <1350000>;
 177                                         regulator-min-microamp = <2500000>;
 178                                         regulator-max-microamp = <4000000>;
 179                                         regulator-always-on;
 180                                         regulator-boot-on;
 181                                         ams,ext-control = <1>;
 182                                 };
 183
 184                                 vdd_1v35_lp0: sd2 {
 185                                         regulator-name = "+1.35V_LP0(sd2)";
 186                                         regulator-min-microvolt = <1350000>;
 187                                         regulator-max-microvolt = <1350000>;
 188                                         regulator-always-on;
 189                                         regulator-boot-on;
 190                                 };
 191
 192                                 sd3 {
 193                                         regulator-name = "+1.35V_LP0(sd3)";
 194                                         regulator-min-microvolt = <1350000>;
 195                                         regulator-max-microvolt = <1350000>;
 196                                         regulator-always-on;
 197                                         regulator-boot-on;
 198                                 };
 199
 200                                 vdd_1v05_run: sd4 {
 201                                         regulator-name = "+1.05V_RUN";
 202                                         regulator-min-microvolt = <1050000>;
 203                                         regulator-max-microvolt = <1050000>;
 204                                 };
 205
 206                                 vddio_1v8: sd5 {
 207                                         regulator-name = "+1.8V_VDDIO";
 208                                         regulator-min-microvolt = <1800000>;
 209                                         regulator-max-microvolt = <1800000>;
 210                                         regulator-always-on;
 211                                 };
 212
 213                                 sd6 {
 214                                         regulator-name = "+VDD_GPU_AP";
 215                                         regulator-min-microvolt = <650000>;
 216                                         regulator-max-microvolt = <1200000>;
 217                                         regulator-min-microamp = <3500000>;
 218                                         regulator-max-microamp = <3500000>;
 219                                         regulator-boot-on;
 220                                         regulator-always-on;
 221                                 };
 222
 223                                 ldo0 {
 224                                         regulator-name = "+1.05V_RUN_AVDD";
 225                                         regulator-min-microvolt = <1050000>;
 226                                         regulator-max-microvolt = <1050000>;
 227                                         regulator-boot-on;
 228                                         regulator-always-on;
 229                                         ams,ext-control = <1>;
 230                                 };
 231
 232                                 ldo1 {
 233                                         regulator-name = "+1.8V_RUN_CAM";
 234                                         regulator-min-microvolt = <1800000>;
 235                                         regulator-max-microvolt = <1800000>;
 236                                 };
 237
 238                                 ldo2 {
 239                                         regulator-name = "+1.2V_GEN_AVDD";
 240                                         regulator-min-microvolt = <1200000>;
 241                                         regulator-max-microvolt = <1200000>;
 242                                         regulator-boot-on;
 243                                         regulator-always-on;
 244                                 };
 245
 246                                 ldo3 {
 247                                         regulator-name = "+1.00V_LP0_VDD_RTC";
 248                                         regulator-min-microvolt = <1000000>;
 249                                         regulator-max-microvolt = <1000000>;
 250                                         regulator-boot-on;
 251                                         regulator-always-on;
 252                                         ams,enable-tracking;
 253                                 };
 254
 255                                 vdd_run_cam: ldo4 {
 256                                         regulator-name = "+3.3V_RUN_CAM";
 257                                         regulator-min-microvolt = <2800000>;
 258                                         regulator-max-microvolt = <2800000>;
 259                                 };
 260
 261                                 ldo5 {
 262                                         regulator-name = "+1.2V_RUN_CAM_FRONT";
 263                                         regulator-min-microvolt = <1200000>;
 264                                         regulator-max-microvolt = <1200000>;
 265                                 };
 266
 267                                 vddio_sdmmc3: ldo6 {
 268                                         regulator-name = "+VDDIO_SDMMC3";
 269                                         regulator-min-microvolt = <1800000>;
 270                                         regulator-max-microvolt = <3300000>;
 271                                 };
 272
 273                                 ldo7 {
 274                                         regulator-name = "+1.05V_RUN_CAM_REAR";
 275                                         regulator-min-microvolt = <1050000>;
 276                                         regulator-max-microvolt = <1050000>;
 277                                 };
 278
 279                                 ldo9 {
 280                                         regulator-name = "+2.8V_RUN_TOUCH";
 281                                         regulator-min-microvolt = <2800000>;
 282                                         regulator-max-microvolt = <2800000>;
 283                                 };
 284
 285                                 ldo10 {
 286                                         regulator-name = "+2.8V_RUN_CAM_AF";
 287                                         regulator-min-microvolt = <2800000>;
 288                                         regulator-max-microvolt = <2800000>;
 289                                 };
 290
 291                                 ldo11 {
 292                                         regulator-name = "+1.8V_RUN_VPP_FUSE";
 293                                         regulator-min-microvolt = <1800000>;
 294                                         regulator-max-microvolt = <1800000>;
 295                                 };
 296                         };
 297                 };
 298         };
 299
 300         spi@7000d400 {
 301                 status = "okay";
 302
 303                 cros_ec: cros-ec@0 {
 304                         compatible = "google,cros-ec-spi";
 305                         spi-max-frequency = <3000000>;
 306                         interrupt-parent = <&gpio>;
 307                         interrupts = <TEGRA_GPIO(C, 7) IRQ_TYPE_LEVEL_LOW>;
 308                         reg = <0>;
 309
 310                         google,cros-ec-spi-msg-delay = <2000>;
 311
 312                         i2c-tunnel {
 313                                 compatible = "google,cros-ec-i2c-tunnel";
 314                                 #address-cells = <1>;
 315                                 #size-cells = <0>;
 316
 317                                 google,remote-bus = <0>;
 318
 319                                 charger: bq24735@9 {
 320                                         compatible = "ti,bq24735";
 321                                         reg = <0x9>;
 322                                         interrupt-parent = <&gpio>;
 323                                         interrupts = <TEGRA_GPIO(J, 0)
 324                                                         GPIO_ACTIVE_HIGH>;
 325                                         ti,ac-detect-gpios = <&gpio
 326                                                         TEGRA_GPIO(J, 0)
 327                                                         GPIO_ACTIVE_HIGH>;
 328                                 };
 329
 330                                 battery: sbs-battery@b {
 331                                         compatible = "sbs,sbs-battery";
 332                                         reg = <0xb>;
 333                                         sbs,i2c-retry-count = <2>;
 334                                         sbs,poll-retry-count = <10>;
 335                                         power-supplies = <&charger>;
 336                                 };
 337                         };
 338                 };
 339         };
 340
 341         spi@7000da00 {
 342                 status = "okay";
 343                 spi-max-frequency = <25000000>;
 344
 345                 flash@0 {
 346                         compatible = "winbond,w25q32dw";
 347                         spi-max-frequency = <25000000>;
 348                         reg = <0>;
 349                 };
 350         };
 351
 352         pmc@7000e400 {
 353                 nvidia,invert-interrupt;
 354                 nvidia,suspend-mode = <0>;
 355                 nvidia,cpu-pwr-good-time = <500>;
 356                 nvidia,cpu-pwr-off-time = <300>;
 357                 nvidia,core-pwr-good-time = <641 3845>;
 358                 nvidia,core-pwr-off-time = <61036>;
 359                 nvidia,core-power-req-active-high;
 360                 nvidia,sys-clock-req-active-high;
 361         };
 362
 363         hda@70030000 {
 364                 status = "okay";
 365         };
 366
 367         sdhci0_pwrseq: sdhci0_pwrseq {
 368                 compatible = "mmc-pwrseq-simple";
 369
 370                 reset-gpios = <&gpio TEGRA_GPIO(X, 7) GPIO_ACTIVE_LOW>;
 371         };
 372
 373         sdhci@700b0000 { /* WiFi/BT on this bus */
 374                 status = "okay";
 375                 power-gpios = <&gpio TEGRA_GPIO(X, 7) GPIO_ACTIVE_HIGH>;
 376                 bus-width = <4>;
 377                 no-1-8-v;
 378                 non-removable;
 379                 mmc-pwrseq = <&sdhci0_pwrseq>;
 380                 vmmc-supply = <&vdd_3v3_lp0>;
 381                 vqmmc-supply = <&vddio_1v8>;
 382                 keep-power-in-suspend;
 383         };
 384
 385         sdhci@700b0400 { /* SD Card on this bus */
 386                 status = "okay";
 387                 cd-gpios = <&gpio TEGRA_GPIO(V, 2) GPIO_ACTIVE_LOW>;
 388                 power-gpios = <&gpio TEGRA_GPIO(R, 0) GPIO_ACTIVE_HIGH>;
 389                 wp-gpios = <&gpio TEGRA_GPIO(Q, 4) GPIO_ACTIVE_LOW>;
 390                 bus-width = <4>;
 391                 no-1-8-v;
 392                 vqmmc-supply = <&vddio_sdmmc3>;
 393         };
 394
 395         sdhci@700b0600 { /* eMMC on this bus */
 396                 status = "okay";
 397                 bus-width = <8>;
 398                 no-1-8-v;
 399                 non-removable;
 400         };
 401
 402         /* CPU DFLL clock */
 403         clock@70110000 {
 404                 status = "disabled";
 405                 vdd-cpu-supply = <&vdd_cpu>;
 406                 nvidia,i2c-fs-rate = <400000>;
 407         };
 408
 409         ahub@70300000 {
 410                 i2s@70301100 {
 411                         status = "okay";
 412                 };
 413         };
 414
 415         usb@7d000000 { /* Rear external USB port. */
 416                 status = "okay";
 417                 nvidia,vbus-gpio = <&gpio TEGRA_GPIO(N, 4) GPIO_ACTIVE_HIGH>;
 418         };
 419
 420         usb-phy@7d000000 {
 421                 status = "okay";
 422                 vbus-supply = <&vdd_usb1_vbus>;
 423         };
 424
 425         usb@7d004000 { /* Internal webcam. */
 426                 status = "okay";
 427         };
 428
 429         usb-phy@7d004000 {
 430                 status = "okay";
 431                 vbus-supply = <&vdd_run_cam>;
 432         };
 433
 434         usb@7d008000 { /* Left external USB port. */
 435                 status = "okay";
 436                 nvidia,vbus-gpio = <&gpio TEGRA_GPIO(N, 5) GPIO_ACTIVE_HIGH>;
 437         };
 438
 439         usb-phy@7d008000 {
 440                 status = "okay";
 441                 vbus-supply = <&vdd_usb3_vbus>;
 442         };
 443
 444         backlight: backlight {
 445                 compatible = "pwm-backlight";
 446
 447                 enable-gpios = <&gpio TEGRA_GPIO(H, 2) GPIO_ACTIVE_HIGH>;
 448                 power-supply = <&vdd_led>;
 449                 pwms = <&pwm 1 1000000>;
 450
 451                 default-brightness-level = <224>;
 452                 brightness-levels =
 453                         <  0   1   2   3   4   5   6   7
 454                            8   9  10  11  12  13  14  15
 455                           16  17  18  19  20  21  22  23
 456                           24  25  26  27  28  29  30  31
 457                           32  33  34  35  36  37  38  39
 458                           40  41  42  43  44  45  46  47
 459                           48  49  50  51  52  53  54  55
 460                           56  57  58  59  60  61  62  63
 461                           64  65  66  67  68  69  70  71
 462                           72  73  74  75  76  77  78  79
 463                           80  81  82  83  84  85  86  87
 464                           88  89  90  91  92  93  94  95
 465                           96  97  98  99 100 101 102 103
 466                          104 105 106 107 108 109 110 111
 467                          112 113 114 115 116 117 118 119
 468                          120 121 122 123 124 125 126 127
 469                          128 129 130 131 132 133 134 135
 470                          136 137 138 139 140 141 142 143
 471                          144 145 146 147 148 149 150 151
 472                          152 153 154 155 156 157 158 159
 473                          160 161 162 163 164 165 166 167
 474                          168 169 170 171 172 173 174 175
 475                          176 177 178 179 180 181 182 183
 476                          184 185 186 187 188 189 190 191
 477                          192 193 194 195 196 197 198 199
 478                          200 201 202 203 204 205 206 207
 479                          208 209 210 211 212 213 214 215
 480                          216 217 218 219 220 221 222 223
 481                          224 225 226 227 228 229 230 231
 482                          232 233 234 235 236 237 238 239
 483                          240 241 242 243 244 245 246 247
 484                          248 249 250 251 252 253 254 255
 485                          256>;
 486         };
 487
 488         clocks {
 489                 compatible = "simple-bus";
 490                 #address-cells = <1>;
 491                 #size-cells = <0>;
 492
 493                 clk32k_in: clock@0 {
 494                         compatible = "fixed-clock";
 495                         reg = <0>;
 496                         #clock-cells = <0>;
 497                         clock-frequency = <32768>;
 498                 };
 499         };
 500
 501         cpus {
 502                 cpu@0 {
 503                         vdd-cpu-supply = <&vdd_cpu>;
 504                 };
 505         };
 506
 507         cpus {
 508                 cpu@0 {
 509                         vdd-cpu-supply = <&vdd_cpu>;
 510                 };
 511         };
 512
 513         gpio-keys {
 514                 compatible = "gpio-keys";
 515
 516                 lid {
 517                         label = "Lid";
 518                         gpios = <&gpio TEGRA_GPIO(R, 4) GPIO_ACTIVE_LOW>;
 519                         linux,input-type = <5>;
 520                         linux,code = <KEY_RESERVED>;
 521                         debounce-interval = <1>;
 522                         gpio-key,wakeup;
 523                 };
 524
 525                 power {
 526                         label = "Power";
 527                         gpios = <&gpio TEGRA_GPIO(Q, 0) GPIO_ACTIVE_LOW>;
 528                         linux,code = <KEY_POWER>;
 529                         debounce-interval = <30>;
 530                         gpio-key,wakeup;
 531                 };
 532         };
 533
 534         regulators {
 535                 compatible = "simple-bus";
 536                 #address-cells = <1>;
 537                 #size-cells = <0>;
 538
 539                 vdd_mux: regulator@0 {
 540                         compatible = "regulator-fixed";
 541                         reg = <0>;
 542                         regulator-name = "+VDD_MUX";
 543                         regulator-min-microvolt = <12000000>;
 544                         regulator-max-microvolt = <12000000>;
 545                         regulator-always-on;
 546                         regulator-boot-on;
 547                 };
 548
 549                 vdd_5v0_sys: regulator@1 {
 550                         compatible = "regulator-fixed";
 551                         reg = <1>;
 552                         regulator-name = "+5V_SYS";
 553                         regulator-min-microvolt = <5000000>;
 554                         regulator-max-microvolt = <5000000>;
 555                         regulator-always-on;
 556                         regulator-boot-on;
 557                         vin-supply = <&vdd_mux>;
 558                 };
 559
 560                 vdd_3v3_sys: regulator@2 {
 561                         compatible = "regulator-fixed";
 562                         reg = <2>;
 563                         regulator-name = "+3.3V_SYS";
 564                         regulator-min-microvolt = <3300000>;
 565                         regulator-max-microvolt = <3300000>;
 566                         regulator-always-on;
 567                         regulator-boot-on;
 568                         vin-supply = <&vdd_mux>;
 569                 };
 570
 571                 vdd_3v3_run: regulator@3 {
 572                         compatible = "regulator-fixed";
 573                         reg = <3>;
 574                         regulator-name = "+3.3V_RUN";
 575                         regulator-min-microvolt = <3300000>;
 576                         regulator-max-microvolt = <3300000>;
 577                         regulator-always-on;
 578                         regulator-boot-on;
 579                         gpio = <&pmic 1 GPIO_ACTIVE_HIGH>;
 580                         enable-active-high;
 581                         vin-supply = <&vdd_3v3_sys>;
 582                 };
 583
 584                 vdd_3v3_hdmi: regulator@4 {
 585                         compatible = "regulator-fixed";
 586                         reg = <4>;
 587                         regulator-name = "+3.3V_AVDD_HDMI_AP_GATED";
 588                         regulator-min-microvolt = <3300000>;
 589                         regulator-max-microvolt = <3300000>;
 590                         vin-supply = <&vdd_3v3_run>;
 591                 };
 592
 593                 vdd_led: regulator@5 {
 594                         compatible = "regulator-fixed";
 595                         reg = <5>;
 596                         regulator-name = "+VDD_LED";
 597                         gpio = <&gpio TEGRA_GPIO(P, 2) GPIO_ACTIVE_HIGH>;
 598                         enable-active-high;
 599                         vin-supply = <&vdd_mux>;
 600                 };
 601
 602                 vdd_5v0_ts: regulator@6 {
 603                         compatible = "regulator-fixed";
 604                         reg = <6>;
 605                         regulator-name = "+5V_VDD_TS_SW";
 606                         regulator-min-microvolt = <5000000>;
 607                         regulator-max-microvolt = <5000000>;
 608                         regulator-boot-on;
 609                         gpio = <&gpio TEGRA_GPIO(K, 1) GPIO_ACTIVE_HIGH>;
 610                         enable-active-high;
 611                         vin-supply = <&vdd_5v0_sys>;
 612                 };
 613
 614                 vdd_usb1_vbus: regulator@7 {
 615                         compatible = "regulator-fixed";
 616                         reg = <7>;
 617                         regulator-name = "+5V_USB_HS";
 618                         regulator-min-microvolt = <5000000>;
 619                         regulator-max-microvolt = <5000000>;
 620                         gpio = <&gpio TEGRA_GPIO(N, 4) GPIO_ACTIVE_HIGH>;
 621                         enable-active-high;
 622                         gpio-open-drain;
 623                         vin-supply = <&vdd_5v0_sys>;
 624                 };
 625
 626                 vdd_usb3_vbus: regulator@8 {
 627                         compatible = "regulator-fixed";
 628                         reg = <8>;
 629                         regulator-name = "+5V_USB_SS";
 630                         regulator-min-microvolt = <5000000>;
 631                         regulator-max-microvolt = <5000000>;
 632                         gpio = <&gpio TEGRA_GPIO(N, 5) GPIO_ACTIVE_HIGH>;
 633                         enable-active-high;
 634                         gpio-open-drain;
 635                         vin-supply = <&vdd_5v0_sys>;
 636                 };
 637
 638                 vdd_3v3_panel: regulator@9 {
 639                         compatible = "regulator-fixed";
 640                         reg = <9>;
 641                         regulator-name = "+3.3V_PANEL";
 642                         regulator-min-microvolt = <3300000>;
 643                         regulator-max-microvolt = <3300000>;
 644                         gpio = <&pmic 4 GPIO_ACTIVE_HIGH>;
 645                         enable-active-high;
 646                         vin-supply = <&vdd_3v3_run>;
 647                 };
 648
 649                 vdd_3v3_lp0: regulator@10 {
 650                         compatible = "regulator-fixed";
 651                         reg = <10>;
 652                         regulator-name = "+3.3V_LP0";
 653                         regulator-min-microvolt = <3300000>;
 654                         regulator-max-microvolt = <3300000>;
 655                         /*
 656                          * TODO: find a way to wire this up with the USB EHCI
 657                          * controllers so that it can be enabled on demand.
 658                          */
 659                         regulator-always-on;
 660                         gpio = <&pmic 2 GPIO_ACTIVE_HIGH>;
 661                         enable-active-high;
 662                         vin-supply = <&vdd_3v3_sys>;
 663                 };
 664
 665                 vdd_hdmi_pll: regulator@11 {
 666                         compatible = "regulator-fixed";
 667                         reg = <11>;
 668                         regulator-name = "+1.05V_RUN_AVDD_HDMI_PLL";
 669                         regulator-min-microvolt = <1050000>;
 670                         regulator-max-microvolt = <1050000>;
 671                         gpio = <&gpio TEGRA_GPIO(H, 7) GPIO_ACTIVE_LOW>;
 672                         vin-supply = <&vdd_1v05_run>;
 673                 };
 674
 675                 vdd_5v0_hdmi: regulator@12 {
 676                         compatible = "regulator-fixed";
 677                         reg = <12>;
 678                         regulator-name = "+5V_HDMI_CON";
 679                         regulator-min-microvolt = <5000000>;
 680                         regulator-max-microvolt = <5000000>;
 681                         gpio = <&gpio TEGRA_GPIO(K, 6) GPIO_ACTIVE_HIGH>;
 682                         enable-active-high;
 683                         vin-supply = <&vdd_5v0_sys>;
 684                 };
 685         };
 686
 687         sound {
 688                 nvidia,audio-routing =
 689                         "Headphones", "HPR",
 690                         "Headphones", "HPL",
 691                         "Speakers", "SPKR",
 692                         "Speakers", "SPKL",
 693                         "Mic Jack", "MICBIAS",
 694                         "DMICL", "Int Mic",
 695                         "DMICR", "Int Mic",
 696                         "IN34", "Mic Jack";
 697
 698                 nvidia,i2s-controller = <&tegra_i2s1>;
 699                 nvidia,audio-codec = <&acodec>;
 700
 701                 clocks = <&tegra_car TEGRA124_CLK_PLL_A>,
 702                          <&tegra_car TEGRA124_CLK_PLL_A_OUT0>,
 703                          <&tegra_car TEGRA124_CLK_EXTERN1>;
 704                 clock-names = "pll_a", "pll_a_out0", "mclk";
 705
 706                 nvidia,hp-det-gpios = <&gpio TEGRA_GPIO(I, 7) GPIO_ACTIVE_HIGH>;
 707                 nvidia,mic-det-gpios =
 708                                 <&gpio TEGRA_GPIO(R, 7) GPIO_ACTIVE_HIGH>;
 709         };
 710
 711         gpio-restart {
 712                 compatible = "gpio-restart";
 713                 gpios = <&gpio TEGRA_GPIO(I, 5) GPIO_ACTIVE_LOW>;
 714                 priority = <200>;
 715         };
 716 };
 717
 718 #include "cros-ec-keyboard.dtsi"