2 * (C) Copyright 2007-2008
3 * Stelian Pop <stelian@popies.net>
4 * Lead Tech Design <www.leadtechdesign.com>
6 * SPDX-License-Identifier: GPL-2.0+
12 #include <asm/arch/at91sam9260_matrix.h>
13 #include <asm/arch/at91_common.h>
14 #include <asm/arch/at91sam9_sdramc.h>
15 #include <asm/arch/clk.h>
16 #include <asm/arch/gpio.h>
19 * if CONFIG_AT91_GPIO_PULLUP ist set, keep pullups on on all
20 * peripheral pins. Good to have if hardware is soldered optionally
21 * or in case of SPI no slave is selected. Avoid lines to float
22 * needlessly. Use a short local PUP define.
24 * Due to errata "TXD floats when CTS is inactive" pullups are always
27 #ifdef CONFIG_AT91_GPIO_PULLUP
28 # define PUP CONFIG_AT91_GPIO_PULLUP
33 void at91_serial0_hw_init(void)
35 at91_set_a_periph(AT91_PIO_PORTB, 4, 1); /* TXD0 */
36 at91_set_a_periph(AT91_PIO_PORTB, 5, PUP); /* RXD0 */
37 at91_periph_clk_enable(ATMEL_ID_USART0);
40 void at91_serial1_hw_init(void)
42 at91_set_a_periph(AT91_PIO_PORTB, 6, 1); /* TXD1 */
43 at91_set_a_periph(AT91_PIO_PORTB, 7, PUP); /* RXD1 */
44 at91_periph_clk_enable(ATMEL_ID_USART1);
47 void at91_serial2_hw_init(void)
49 at91_set_a_periph(AT91_PIO_PORTB, 8, 1); /* TXD2 */
50 at91_set_a_periph(AT91_PIO_PORTB, 9, PUP); /* RXD2 */
51 at91_periph_clk_enable(ATMEL_ID_USART2);
54 void at91_seriald_hw_init(void)
56 at91_set_a_periph(AT91_PIO_PORTB, 14, PUP); /* DRXD */
57 at91_set_a_periph(AT91_PIO_PORTB, 15, 1); /* DTXD */
58 at91_periph_clk_enable(ATMEL_ID_SYS);
61 #if defined(CONFIG_HAS_DATAFLASH) || defined(CONFIG_ATMEL_SPI)
62 void at91_spi0_hw_init(unsigned long cs_mask)
64 at91_set_a_periph(AT91_PIO_PORTA, 0, PUP); /* SPI0_MISO */
65 at91_set_a_periph(AT91_PIO_PORTA, 1, PUP); /* SPI0_MOSI */
66 at91_set_a_periph(AT91_PIO_PORTA, 2, PUP); /* SPI0_SPCK */
68 at91_periph_clk_enable(ATMEL_ID_SPI0);
70 if (cs_mask & (1 << 0)) {
71 at91_set_a_periph(AT91_PIO_PORTA, 3, 1);
73 if (cs_mask & (1 << 1)) {
74 at91_set_b_periph(AT91_PIO_PORTC, 11, 1);
76 if (cs_mask & (1 << 2)) {
77 at91_set_b_periph(AT91_PIO_PORTC, 16, 1);
79 if (cs_mask & (1 << 3)) {
80 at91_set_b_periph(AT91_PIO_PORTC, 17, 1);
82 if (cs_mask & (1 << 4)) {
83 at91_set_pio_output(AT91_PIO_PORTA, 3, 1);
85 if (cs_mask & (1 << 5)) {
86 at91_set_pio_output(AT91_PIO_PORTC, 11, 1);
88 if (cs_mask & (1 << 6)) {
89 at91_set_pio_output(AT91_PIO_PORTC, 16, 1);
91 if (cs_mask & (1 << 7)) {
92 at91_set_pio_output(AT91_PIO_PORTC, 17, 1);
96 void at91_spi1_hw_init(unsigned long cs_mask)
98 at91_set_a_periph(AT91_PIO_PORTB, 0, PUP); /* SPI1_MISO */
99 at91_set_a_periph(AT91_PIO_PORTB, 1, PUP); /* SPI1_MOSI */
100 at91_set_a_periph(AT91_PIO_PORTB, 2, PUP); /* SPI1_SPCK */
102 at91_periph_clk_enable(ATMEL_ID_SPI1);
104 if (cs_mask & (1 << 0)) {
105 at91_set_a_periph(AT91_PIO_PORTB, 3, 1);
107 if (cs_mask & (1 << 1)) {
108 at91_set_b_periph(AT91_PIO_PORTC, 5, 1);
110 if (cs_mask & (1 << 2)) {
111 at91_set_b_periph(AT91_PIO_PORTC, 4, 1);
113 if (cs_mask & (1 << 3)) {
114 at91_set_b_periph(AT91_PIO_PORTC, 3, 1);
116 if (cs_mask & (1 << 4)) {
117 at91_set_pio_output(AT91_PIO_PORTB, 3, 1);
119 if (cs_mask & (1 << 5)) {
120 at91_set_pio_output(AT91_PIO_PORTC, 5, 1);
122 if (cs_mask & (1 << 6)) {
123 at91_set_pio_output(AT91_PIO_PORTC, 4, 1);
125 if (cs_mask & (1 << 7)) {
126 at91_set_pio_output(AT91_PIO_PORTC, 3, 1);
132 void at91_macb_hw_init(void)
134 at91_periph_clk_enable(ATMEL_ID_EMAC0);
136 at91_set_a_periph(AT91_PIO_PORTA, 19, 0); /* ETXCK_EREFCK */
137 at91_set_a_periph(AT91_PIO_PORTA, 17, 0); /* ERXDV */
138 at91_set_a_periph(AT91_PIO_PORTA, 14, 0); /* ERX0 */
139 at91_set_a_periph(AT91_PIO_PORTA, 15, 0); /* ERX1 */
140 at91_set_a_periph(AT91_PIO_PORTA, 18, 0); /* ERXER */
141 at91_set_a_periph(AT91_PIO_PORTA, 16, 0); /* ETXEN */
142 at91_set_a_periph(AT91_PIO_PORTA, 12, 0); /* ETX0 */
143 at91_set_a_periph(AT91_PIO_PORTA, 13, 0); /* ETX1 */
144 at91_set_a_periph(AT91_PIO_PORTA, 21, 0); /* EMDIO */
145 at91_set_a_periph(AT91_PIO_PORTA, 20, 0); /* EMDC */
148 at91_set_b_periph(AT91_PIO_PORTA, 28, 0); /* ECRS */
149 at91_set_b_periph(AT91_PIO_PORTA, 29, 0); /* ECOL */
150 at91_set_b_periph(AT91_PIO_PORTA, 25, 0); /* ERX2 */
151 at91_set_b_periph(AT91_PIO_PORTA, 26, 0); /* ERX3 */
152 at91_set_b_periph(AT91_PIO_PORTA, 27, 0); /* ERXCK */
153 #if defined(CONFIG_AT91SAM9260EK)
155 * use PA10, PA11 for ETX2, ETX3.
156 * PA23 and PA24 are for TWI EEPROM
158 at91_set_b_periph(AT91_PIO_PORTA, 10, 0); /* ETX2 */
159 at91_set_b_periph(AT91_PIO_PORTA, 11, 0); /* ETX3 */
161 at91_set_b_periph(AT91_PIO_PORTA, 23, 0); /* ETX2 */
162 at91_set_b_periph(AT91_PIO_PORTA, 24, 0); /* ETX3 */
163 #if defined(CONFIG_AT91SAM9G20)
164 /* 9G20 BOOT ROM initializes those pins to multi-drive, undo that */
165 at91_set_pio_multi_drive(AT91_PIO_PORTA, 23, 0);
166 at91_set_pio_multi_drive(AT91_PIO_PORTA, 24, 0);
169 at91_set_b_periph(AT91_PIO_PORTA, 22, 0); /* ETXER */
174 #if defined(CONFIG_GENERIC_ATMEL_MCI)
175 void at91_mci_hw_init(void)
177 at91_periph_clk_enable(ATMEL_ID_MCI);
179 at91_set_a_periph(AT91_PIO_PORTA, 8, 1); /* MCCK */
180 #if defined(CONFIG_ATMEL_MCI_PORTB)
181 at91_set_b_periph(AT91_PIO_PORTA, 1, 1); /* MCCDB */
182 at91_set_b_periph(AT91_PIO_PORTA, 0, 1); /* MCDB0 */
183 at91_set_b_periph(AT91_PIO_PORTA, 5, 1); /* MCDB1 */
184 at91_set_b_periph(AT91_PIO_PORTA, 4, 1); /* MCDB2 */
185 at91_set_b_periph(AT91_PIO_PORTA, 3, 1); /* MCDB3 */
187 at91_set_a_periph(AT91_PIO_PORTA, 7, 1); /* MCCDA */
188 at91_set_a_periph(AT91_PIO_PORTA, 6, 1); /* MCDA0 */
189 at91_set_a_periph(AT91_PIO_PORTA, 9, 1); /* MCDA1 */
190 at91_set_a_periph(AT91_PIO_PORTA, 10, 1); /* MCDA2 */
191 at91_set_a_periph(AT91_PIO_PORTA, 11, 1); /* MCDA3 */
196 void at91_sdram_hw_init(void)
198 at91_set_a_periph(AT91_PIO_PORTC, 16, 0);
199 at91_set_a_periph(AT91_PIO_PORTC, 17, 0);
200 at91_set_a_periph(AT91_PIO_PORTC, 18, 0);
201 at91_set_a_periph(AT91_PIO_PORTC, 19, 0);
202 at91_set_a_periph(AT91_PIO_PORTC, 20, 0);
203 at91_set_a_periph(AT91_PIO_PORTC, 21, 0);
204 at91_set_a_periph(AT91_PIO_PORTC, 22, 0);
205 at91_set_a_periph(AT91_PIO_PORTC, 23, 0);
206 at91_set_a_periph(AT91_PIO_PORTC, 24, 0);
207 at91_set_a_periph(AT91_PIO_PORTC, 25, 0);
208 at91_set_a_periph(AT91_PIO_PORTC, 26, 0);
209 at91_set_a_periph(AT91_PIO_PORTC, 27, 0);
210 at91_set_a_periph(AT91_PIO_PORTC, 28, 0);
211 at91_set_a_periph(AT91_PIO_PORTC, 29, 0);
212 at91_set_a_periph(AT91_PIO_PORTC, 30, 0);
213 at91_set_a_periph(AT91_PIO_PORTC, 31, 0);
216 /* Platform data for the GPIOs */
217 static const struct at91_port_platdata at91sam9260_plat[] = {
218 { ATMEL_BASE_PIOA, "PA" },
219 { ATMEL_BASE_PIOB, "PB" },
220 { ATMEL_BASE_PIOC, "PC" },
223 U_BOOT_DEVICES(at91sam9260_gpios) = {
224 { "gpio_at91", &at91sam9260_plat[0] },
225 { "gpio_at91", &at91sam9260_plat[1] },
226 { "gpio_at91", &at91sam9260_plat[2] },