3 config SPL_LIBCOMMON_SUPPORT
6 config SPL_LIBGENERIC_SUPPORT
12 config ARCH_UNIPHIER_32BIT
15 select CPU_V7_HAS_NONSEC
17 select ARCH_SUPPORT_PSCI
19 config ARCH_UNIPHIER_64BIT
22 select SPL_SEPARATE_BSS
23 select ARMV8_MULTIENTRY
24 select ARMV8_SPIN_TABLE
27 prompt "UniPhier SoC select"
28 default ARCH_UNIPHIER_PRO4
30 config ARCH_UNIPHIER_SLD3
31 bool "UniPhier PH1-sLD3 SoC"
32 select ARCH_UNIPHIER_32BIT
34 config ARCH_UNIPHIER_LD4_SLD8
35 bool "UniPhier PH1-LD4/PH1-sLD8 SoC"
36 select ARCH_UNIPHIER_32BIT
38 config ARCH_UNIPHIER_PRO4
39 bool "UniPhier PH1-Pro4 SoC"
40 select ARCH_UNIPHIER_32BIT
42 config ARCH_UNIPHIER_PRO5_PXS2_LD6B
43 bool "UniPhier PH1-Pro5/ProXstream2/PH1-LD6b SoC"
44 select ARCH_UNIPHIER_32BIT
46 config ARCH_UNIPHIER_LD11
47 bool "UniPhier PH1-LD11 SoC"
48 select ARCH_UNIPHIER_64BIT
50 config ARCH_UNIPHIER_LD20
51 bool "UniPhier PH1-LD20 SoC"
52 select ARCH_UNIPHIER_64BIT
57 config ARCH_UNIPHIER_LD4
58 bool "Enable UniPhier PH1-LD4 SoC support"
59 depends on ARCH_UNIPHIER_LD4_SLD8
62 config ARCH_UNIPHIER_SLD8
63 bool "Enable UniPhier PH1-sLD8 SoC support"
64 depends on ARCH_UNIPHIER_LD4_SLD8
67 config ARCH_UNIPHIER_PRO5
68 bool "Enable UniPhier PH1-Pro5 SoC support"
69 depends on ARCH_UNIPHIER_PRO5_PXS2_LD6B
72 config ARCH_UNIPHIER_PXS2
73 bool "Enable UniPhier ProXstream2 SoC support"
74 depends on ARCH_UNIPHIER_PRO5_PXS2_LD6B
77 config ARCH_UNIPHIER_LD6B
78 bool "Enable UniPhier PH1-LD6b SoC support"
79 depends on ARCH_UNIPHIER_PRO5_PXS2_LD6B
83 bool "Enable the UniPhier L2 cache controller"
84 depends on ARCH_UNIPHIER_32BIT
85 select SYS_CACHE_SHIFT_7
88 This option allows to use the UniPhier System Cache as L2 cache.
90 config MICRO_SUPPORT_CARD
91 bool "Use Micro Support Card"
93 This option provides support for the expansion board, available
94 on some UniPhier reference boards.
96 Say Y to use the on-board UART, Ether, LED devices.
99 bool "Enable boot mode pins monitor command"
102 The command "pinmon" shows the state of the boot mode pins.
103 The boot mode pins are latched when the system reset is deasserted
104 and determine which device the system should load a boot image from.
106 config CMD_DDRPHY_DUMP
107 bool "Enable dump command of DDR PHY parameters"
108 depends on ARCH_UNIPHIER_LD4 || ARCH_UNIPHIER_PRO4 || ARCH_UNIPHIER_SLD8
111 The command "ddrphy" shows the resulting parameters of DDR PHY
112 training; it is useful for the evaluation of DDR PHY training.
114 config CMD_DDRMPHY_DUMP
115 bool "Enable dump command of DDR Multi PHY parameters"
116 depends on ARCH_UNIPHIER_PXS2 || ARCH_UNIPHIER_LD6B
119 The command "ddrmphy" shows the resulting parameters of DDR Multi PHY
120 training; it is useful for the evaluation of DDR Multi PHY training.