6 config ARCH_UNIPHIER_32BIT
9 select CPU_V7_HAS_NONSEC
11 select ARCH_SUPPORT_PSCI
13 config ARCH_UNIPHIER_64BIT
16 select SPL_SEPARATE_BSS if SPL
17 select ARMV8_MULTIENTRY if SPL
18 select ARMV8_SPIN_TABLE if SPL
21 prompt "UniPhier SoC select"
22 default ARCH_UNIPHIER_PRO4
24 config ARCH_UNIPHIER_SLD3
25 bool "UniPhier sLD3 SoC"
26 select ARCH_UNIPHIER_32BIT
28 config ARCH_UNIPHIER_LD4_SLD8
29 bool "UniPhier LD4/sLD8 SoCs"
30 select ARCH_UNIPHIER_32BIT
32 config ARCH_UNIPHIER_PRO4
33 bool "UniPhier Pro4 SoC"
34 select ARCH_UNIPHIER_32BIT
36 config ARCH_UNIPHIER_PRO5_PXS2_LD6B
37 bool "UniPhier Pro5/PXs2/LD6b SoCs"
38 select ARCH_UNIPHIER_32BIT
40 config ARCH_UNIPHIER_LD11_SINGLE
41 bool "UniPhier LD11 SoC"
42 select ARCH_UNIPHIER_64BIT
44 config ARCH_UNIPHIER_LD20_SINGLE
45 bool "UniPhier LD20 SoC"
46 select ARCH_UNIPHIER_64BIT
48 config ARCH_UNIPHIER_V8_MULTI
49 bool "UniPhier V8 SoCs"
51 select ARCH_UNIPHIER_64BIT
55 config ARCH_UNIPHIER_LD4
56 bool "Enable UniPhier LD4 SoC support"
57 depends on ARCH_UNIPHIER_LD4_SLD8
60 config ARCH_UNIPHIER_SLD8
61 bool "Enable UniPhier sLD8 SoC support"
62 depends on ARCH_UNIPHIER_LD4_SLD8
65 config ARCH_UNIPHIER_PRO5
66 bool "Enable UniPhier Pro5 SoC support"
67 depends on ARCH_UNIPHIER_PRO5_PXS2_LD6B
70 config ARCH_UNIPHIER_PXS2
71 bool "Enable UniPhier Pxs2 SoC support"
72 depends on ARCH_UNIPHIER_PRO5_PXS2_LD6B
75 config ARCH_UNIPHIER_LD6B
76 bool "Enable UniPhier LD6b SoC support"
77 depends on ARCH_UNIPHIER_PRO5_PXS2_LD6B
80 config ARCH_UNIPHIER_LD11
81 bool "Enable UniPhier LD11 SoC support" if ARCH_UNIPHIER_V8_MULTI
82 depends on ARCH_UNIPHIER_LD11_SINGLE || ARCH_UNIPHIER_V8_MULTI
85 config ARCH_UNIPHIER_LD20
86 bool "Enable UniPhier LD20 SoC support" if ARCH_UNIPHIER_V8_MULTI
87 depends on ARCH_UNIPHIER_LD20_SINGLE || ARCH_UNIPHIER_V8_MULTI
92 bool "Enable the UniPhier L2 cache controller"
93 depends on ARCH_UNIPHIER_32BIT
94 select SYS_CACHE_SHIFT_7
97 This option allows to use the UniPhier System Cache as L2 cache.
99 config MICRO_SUPPORT_CARD
100 bool "Use Micro Support Card"
102 This option provides support for the expansion board, available
103 on some UniPhier reference boards.
105 Say Y to use the on-board UART, Ether, LED devices.
108 bool "Enable boot mode pins monitor command"
111 The command "pinmon" shows the state of the boot mode pins.
112 The boot mode pins are latched when the system reset is deasserted
113 and determine which device the system should load a boot image from.
115 config CMD_DDRPHY_DUMP
116 bool "Enable dump command of DDR PHY parameters"
117 depends on ARCH_UNIPHIER_LD4 || ARCH_UNIPHIER_PRO4 || \
118 ARCH_UNIPHIER_SLD8 || ARCH_UNIPHIER_LD11
121 The command "ddrphy" shows the resulting parameters of DDR PHY
122 training; it is useful for the evaluation of DDR PHY training.
124 config CMD_DDRMPHY_DUMP
125 bool "Enable dump command of DDR Multi PHY parameters"
126 depends on ARCH_UNIPHIER_PXS2 || ARCH_UNIPHIER_LD6B
129 The command "ddrmphy" shows the resulting parameters of DDR Multi PHY
130 training; it is useful for the evaluation of DDR Multi PHY training.