6 config ARCH_UNIPHIER_32BIT
9 select CPU_V7_HAS_NONSEC
12 config ARCH_UNIPHIER_64BIT
15 select SPL_SEPARATE_BSS
16 select ARMV8_MULTIENTRY
17 select ARMV8_SPIN_TABLE
20 prompt "UniPhier SoC select"
21 default ARCH_UNIPHIER_PRO4
23 config ARCH_UNIPHIER_SLD3
24 bool "UniPhier PH1-sLD3 SoC"
25 select ARCH_UNIPHIER_32BIT
27 config ARCH_UNIPHIER_LD4_SLD8
28 bool "UniPhier PH1-LD4/PH1-sLD8 SoC"
29 select ARCH_UNIPHIER_32BIT
31 config ARCH_UNIPHIER_PRO4
32 bool "UniPhier PH1-Pro4 SoC"
33 select ARCH_UNIPHIER_32BIT
35 config ARCH_UNIPHIER_PRO5_PXS2_LD6B
36 bool "UniPhier PH1-Pro5/ProXstream2/PH1-LD6b SoC"
37 select ARCH_UNIPHIER_32BIT
39 config ARCH_UNIPHIER_LD11
40 bool "UniPhier PH1-LD11 SoC"
41 select ARCH_UNIPHIER_64BIT
43 config ARCH_UNIPHIER_LD20
44 bool "UniPhier PH1-LD20 SoC"
45 select ARCH_UNIPHIER_64BIT
50 config ARCH_UNIPHIER_LD4
51 bool "Enable UniPhier PH1-LD4 SoC support"
52 depends on ARCH_UNIPHIER_LD4_SLD8
55 config ARCH_UNIPHIER_SLD8
56 bool "Enable UniPhier PH1-sLD8 SoC support"
57 depends on ARCH_UNIPHIER_LD4_SLD8
60 config ARCH_UNIPHIER_PRO5
61 bool "Enable UniPhier PH1-Pro5 SoC support"
62 depends on ARCH_UNIPHIER_PRO5_PXS2_LD6B
65 config ARCH_UNIPHIER_PXS2
66 bool "Enable UniPhier ProXstream2 SoC support"
67 depends on ARCH_UNIPHIER_PRO5_PXS2_LD6B
70 config ARCH_UNIPHIER_LD6B
71 bool "Enable UniPhier PH1-LD6b SoC support"
72 depends on ARCH_UNIPHIER_PRO5_PXS2_LD6B
76 bool "Enable the UniPhier L2 cache controller"
77 depends on ARCH_UNIPHIER_32BIT
80 This option allows to use the UniPhier System Cache as L2 cache.
82 config MICRO_SUPPORT_CARD
83 bool "Use Micro Support Card"
85 This option provides support for the expansion board, available
86 on some UniPhier reference boards.
88 Say Y to use the on-board UART, Ether, LED devices.
91 bool "Enable boot mode pins monitor command"
94 The command "pinmon" shows the state of the boot mode pins.
95 The boot mode pins are latched when the system reset is deasserted
96 and determine which device the system should load a boot image from.
98 config CMD_DDRPHY_DUMP
99 bool "Enable dump command of DDR PHY parameters"
100 depends on ARCH_UNIPHIER_LD4 || ARCH_UNIPHIER_PRO4 || ARCH_UNIPHIER_SLD8
103 The command "ddrphy" shows the resulting parameters of DDR PHY
104 training; it is useful for the evaluation of DDR PHY training.
106 config CMD_DDRMPHY_DUMP
107 bool "Enable dump command of DDR Multi PHY parameters"
108 depends on ARCH_UNIPHIER_PXS2 || ARCH_UNIPHIER_LD6B
111 The command "ddrmphy" shows the resulting parameters of DDR Multi PHY
112 training; it is useful for the evaluation of DDR Multi PHY training.