3 config SPL_LIBCOMMON_SUPPORT
6 config SPL_LIBGENERIC_SUPPORT
10 default y if !ARCH_UNIPHIER_64BIT
12 config SPL_NAND_SUPPORT
15 config SPL_SERIAL_SUPPORT
18 config SYS_CONFIG_NAME
21 config ARCH_UNIPHIER_32BIT
24 select CPU_V7_HAS_NONSEC
26 select ARCH_SUPPORT_PSCI
28 config ARCH_UNIPHIER_64BIT
31 select SPL_SEPARATE_BSS
32 select ARMV8_MULTIENTRY
33 select ARMV8_SPIN_TABLE
36 prompt "UniPhier SoC select"
37 default ARCH_UNIPHIER_PRO4
39 config ARCH_UNIPHIER_SLD3
40 bool "UniPhier PH1-sLD3 SoC"
41 select ARCH_UNIPHIER_32BIT
43 config ARCH_UNIPHIER_LD4_SLD8
44 bool "UniPhier PH1-LD4/PH1-sLD8 SoC"
45 select ARCH_UNIPHIER_32BIT
47 config ARCH_UNIPHIER_PRO4
48 bool "UniPhier PH1-Pro4 SoC"
49 select ARCH_UNIPHIER_32BIT
51 config ARCH_UNIPHIER_PRO5_PXS2_LD6B
52 bool "UniPhier PH1-Pro5/ProXstream2/PH1-LD6b SoC"
53 select ARCH_UNIPHIER_32BIT
55 config ARCH_UNIPHIER_LD11
56 bool "UniPhier PH1-LD11 SoC"
57 select ARCH_UNIPHIER_64BIT
59 config ARCH_UNIPHIER_LD20
60 bool "UniPhier PH1-LD20 SoC"
61 select ARCH_UNIPHIER_64BIT
66 config ARCH_UNIPHIER_LD4
67 bool "Enable UniPhier PH1-LD4 SoC support"
68 depends on ARCH_UNIPHIER_LD4_SLD8
71 config ARCH_UNIPHIER_SLD8
72 bool "Enable UniPhier PH1-sLD8 SoC support"
73 depends on ARCH_UNIPHIER_LD4_SLD8
76 config ARCH_UNIPHIER_PRO5
77 bool "Enable UniPhier PH1-Pro5 SoC support"
78 depends on ARCH_UNIPHIER_PRO5_PXS2_LD6B
81 config ARCH_UNIPHIER_PXS2
82 bool "Enable UniPhier ProXstream2 SoC support"
83 depends on ARCH_UNIPHIER_PRO5_PXS2_LD6B
86 config ARCH_UNIPHIER_LD6B
87 bool "Enable UniPhier PH1-LD6b SoC support"
88 depends on ARCH_UNIPHIER_PRO5_PXS2_LD6B
92 bool "Enable the UniPhier L2 cache controller"
93 depends on ARCH_UNIPHIER_32BIT
94 select SYS_CACHE_SHIFT_7
97 This option allows to use the UniPhier System Cache as L2 cache.
99 config MICRO_SUPPORT_CARD
100 bool "Use Micro Support Card"
102 This option provides support for the expansion board, available
103 on some UniPhier reference boards.
105 Say Y to use the on-board UART, Ether, LED devices.
108 bool "Enable boot mode pins monitor command"
111 The command "pinmon" shows the state of the boot mode pins.
112 The boot mode pins are latched when the system reset is deasserted
113 and determine which device the system should load a boot image from.
115 config CMD_DDRPHY_DUMP
116 bool "Enable dump command of DDR PHY parameters"
117 depends on ARCH_UNIPHIER_LD4 || ARCH_UNIPHIER_PRO4 || ARCH_UNIPHIER_SLD8
120 The command "ddrphy" shows the resulting parameters of DDR PHY
121 training; it is useful for the evaluation of DDR PHY training.
123 config CMD_DDRMPHY_DUMP
124 bool "Enable dump command of DDR Multi PHY parameters"
125 depends on ARCH_UNIPHIER_PXS2 || ARCH_UNIPHIER_LD6B
128 The command "ddrmphy" shows the resulting parameters of DDR Multi PHY
129 training; it is useful for the evaluation of DDR Multi PHY training.