3 config SPL_LIBCOMMON_SUPPORT
6 config SPL_LIBGENERIC_SUPPORT
10 default y if !ARCH_UNIPHIER_64BIT
12 config SPL_NAND_SUPPORT
15 config SYS_CONFIG_NAME
18 config ARCH_UNIPHIER_32BIT
21 select CPU_V7_HAS_NONSEC
23 select ARCH_SUPPORT_PSCI
25 config ARCH_UNIPHIER_64BIT
28 select SPL_SEPARATE_BSS
29 select ARMV8_MULTIENTRY
30 select ARMV8_SPIN_TABLE
33 prompt "UniPhier SoC select"
34 default ARCH_UNIPHIER_PRO4
36 config ARCH_UNIPHIER_SLD3
37 bool "UniPhier PH1-sLD3 SoC"
38 select ARCH_UNIPHIER_32BIT
40 config ARCH_UNIPHIER_LD4_SLD8
41 bool "UniPhier PH1-LD4/PH1-sLD8 SoC"
42 select ARCH_UNIPHIER_32BIT
44 config ARCH_UNIPHIER_PRO4
45 bool "UniPhier PH1-Pro4 SoC"
46 select ARCH_UNIPHIER_32BIT
48 config ARCH_UNIPHIER_PRO5_PXS2_LD6B
49 bool "UniPhier PH1-Pro5/ProXstream2/PH1-LD6b SoC"
50 select ARCH_UNIPHIER_32BIT
52 config ARCH_UNIPHIER_LD11
53 bool "UniPhier PH1-LD11 SoC"
54 select ARCH_UNIPHIER_64BIT
56 config ARCH_UNIPHIER_LD20
57 bool "UniPhier PH1-LD20 SoC"
58 select ARCH_UNIPHIER_64BIT
63 config ARCH_UNIPHIER_LD4
64 bool "Enable UniPhier PH1-LD4 SoC support"
65 depends on ARCH_UNIPHIER_LD4_SLD8
68 config ARCH_UNIPHIER_SLD8
69 bool "Enable UniPhier PH1-sLD8 SoC support"
70 depends on ARCH_UNIPHIER_LD4_SLD8
73 config ARCH_UNIPHIER_PRO5
74 bool "Enable UniPhier PH1-Pro5 SoC support"
75 depends on ARCH_UNIPHIER_PRO5_PXS2_LD6B
78 config ARCH_UNIPHIER_PXS2
79 bool "Enable UniPhier ProXstream2 SoC support"
80 depends on ARCH_UNIPHIER_PRO5_PXS2_LD6B
83 config ARCH_UNIPHIER_LD6B
84 bool "Enable UniPhier PH1-LD6b SoC support"
85 depends on ARCH_UNIPHIER_PRO5_PXS2_LD6B
89 bool "Enable the UniPhier L2 cache controller"
90 depends on ARCH_UNIPHIER_32BIT
91 select SYS_CACHE_SHIFT_7
94 This option allows to use the UniPhier System Cache as L2 cache.
96 config MICRO_SUPPORT_CARD
97 bool "Use Micro Support Card"
99 This option provides support for the expansion board, available
100 on some UniPhier reference boards.
102 Say Y to use the on-board UART, Ether, LED devices.
105 bool "Enable boot mode pins monitor command"
108 The command "pinmon" shows the state of the boot mode pins.
109 The boot mode pins are latched when the system reset is deasserted
110 and determine which device the system should load a boot image from.
112 config CMD_DDRPHY_DUMP
113 bool "Enable dump command of DDR PHY parameters"
114 depends on ARCH_UNIPHIER_LD4 || ARCH_UNIPHIER_PRO4 || ARCH_UNIPHIER_SLD8
117 The command "ddrphy" shows the resulting parameters of DDR PHY
118 training; it is useful for the evaluation of DDR PHY training.
120 config CMD_DDRMPHY_DUMP
121 bool "Enable dump command of DDR Multi PHY parameters"
122 depends on ARCH_UNIPHIER_PXS2 || ARCH_UNIPHIER_LD6B
125 The command "ddrmphy" shows the resulting parameters of DDR Multi PHY
126 training; it is useful for the evaluation of DDR Multi PHY training.