2 * URB OHCI HCD (Host Controller Driver) for USB on the AU1x00.
5 * Gary Jennejohn, DENX Software Engineering <garyj@denx.de>
7 * SPDX-License-Identifier: GPL-2.0+
8 * Note: Part of this code has been derived from linux
13 * 1 - this driver is intended for use with USB Mass Storage Devices
14 * (BBB) ONLY. There is NO support for Interrupt or Isochronous pipes!
19 #ifdef CONFIG_USB_OHCI
21 /* #include <pci.h> no PCI on the AU1x00 */
26 #include <mach/au1x00.h>
28 #include "au1x00_usb_ohci.h"
30 #define OHCI_USE_NPS /* force NoPowerSwitching mode */
31 #define OHCI_VERBOSE_DEBUG /* not always helpful */
32 #define OHCI_FILL_TRACE
34 #define USBH_ENABLE_BE (1<<0)
35 #define USBH_ENABLE_C (1<<1)
36 #define USBH_ENABLE_E (1<<2)
37 #define USBH_ENABLE_CE (1<<3)
38 #define USBH_ENABLE_RD (1<<4)
40 #ifdef __LITTLE_ENDIAN
41 #define USBH_ENABLE_INIT (USBH_ENABLE_CE | USBH_ENABLE_E | USBH_ENABLE_C)
43 #define USBH_ENABLE_INIT (USBH_ENABLE_CE | USBH_ENABLE_E | USBH_ENABLE_C | USBH_ENABLE_BE)
47 /* For initializing controller (mask in an HCFS mode too) */
48 #define OHCI_CONTROL_INIT \
49 (OHCI_CTRL_CBSR & 0x3) | OHCI_CTRL_IE | OHCI_CTRL_PLE
54 #define readl(a) au_readl((long)(a))
55 #define writel(v,a) au_writel((v),(int)(a))
59 #define dbg(format, arg...) printf("DEBUG: " format "\n", ## arg)
61 #define dbg(format, arg...) do {} while(0)
63 #define err(format, arg...) printf("ERROR: " format "\n", ## arg)
66 #define info(format, arg...) printf("INFO: " format "\n", ## arg)
68 #define info(format, arg...) do {} while(0)
71 #define m16_swap(x) swap_16(x)
72 #define m32_swap(x) swap_32(x)
76 /* this must be aligned to a 256 byte boundary */
77 struct ohci_hcca ghcca[1];
78 /* a pointer to the aligned storage */
79 struct ohci_hcca *phcca;
80 /* this allocates EDs for all possible endpoints */
81 struct ohci_device ohci_dev;
86 /* device which was disconnected */
87 struct usb_device *devgone;
89 /*-------------------------------------------------------------------------*/
91 /* AMD-756 (D2 rev) reports corrupt register contents in some cases.
92 * The erratum (#4) description is incorrect. AMD's workaround waits
93 * till some bits (mostly reserved) are clear; ok for all revs.
95 #define OHCI_QUIRK_AMD756 0xabcd
96 #define read_roothub(hc, register, mask) ({ \
97 u32 temp = readl (&hc->regs->roothub.register); \
98 if (hc->flags & OHCI_QUIRK_AMD756) \
100 temp = readl (&hc->regs->roothub.register); \
103 static u32 roothub_a (struct ohci *hc)
104 { return read_roothub (hc, a, 0xfc0fe000); }
105 static inline u32 roothub_b (struct ohci *hc)
106 { return readl (&hc->regs->roothub.b); }
107 static inline u32 roothub_status (struct ohci *hc)
108 { return readl (&hc->regs->roothub.status); }
109 static u32 roothub_portstatus (struct ohci *hc, int i)
110 { return read_roothub (hc, portstatus [i], 0xffe0fce0); }
113 /* forward declaration */
114 static int hc_interrupt (void);
116 td_submit_job (struct usb_device * dev, unsigned long pipe, void * buffer,
117 int transfer_len, struct devrequest * setup, urb_priv_t * urb, int interval);
119 /*-------------------------------------------------------------------------*
120 * URB support functions
121 *-------------------------------------------------------------------------*/
123 /* free HCD-private data associated with this URB */
125 static void urb_free_priv (urb_priv_t * urb)
131 last = urb->length - 1;
133 for (i = 0; i <= last; i++) {
143 /*-------------------------------------------------------------------------*/
146 static int sohci_get_current_frame_number (struct usb_device * dev);
148 /* debug| print the main components of an URB
149 * small: 0) header + data packets 1) just header */
151 static void pkt_print (struct usb_device * dev, unsigned long pipe, void * buffer,
152 int transfer_len, struct devrequest * setup, char * str, int small)
154 urb_priv_t * purb = &urb_priv;
156 dbg("%s URB:[%4x] dev:%2d,ep:%2d-%c,type:%s,len:%d/%d stat:%#lx",
158 sohci_get_current_frame_number (dev),
159 usb_pipedevice (pipe),
160 usb_pipeendpoint (pipe),
161 usb_pipeout (pipe)? 'O': 'I',
162 usb_pipetype (pipe) < 2? (usb_pipeint (pipe)? "INTR": "ISOC"):
163 (usb_pipecontrol (pipe)? "CTRL": "BULK"),
165 transfer_len, dev->status);
166 #ifdef OHCI_VERBOSE_DEBUG
170 if (usb_pipecontrol (pipe)) {
171 printf (__FILE__ ": cmd(8):");
172 for (i = 0; i < 8 ; i++)
173 printf (" %02x", ((__u8 *) setup) [i]);
176 if (transfer_len > 0 && buffer) {
177 printf (__FILE__ ": data(%d/%d):",
180 len = usb_pipeout (pipe)?
181 transfer_len: purb->actual_length;
182 for (i = 0; i < 16 && i < len; i++)
183 printf (" %02x", ((__u8 *) buffer) [i]);
184 printf ("%s\n", i < len? "...": "");
190 /* just for debugging; prints non-empty branches of the int ed tree inclusive iso eds*/
191 void ep_print_int_eds (ohci_t *ohci, char * str) {
194 for (i= 0; i < 32; i++) {
196 ed_p = &(ohci->hcca->int_table [i]);
199 printf (__FILE__ ": %s branch int %2d(%2x):", str, i, i);
200 while (*ed_p != 0 && j--) {
201 ed_t *ed = (ed_t *)m32_swap(ed_p);
202 printf (" ed: %4x;", ed->hwINFO);
203 ed_p = &ed->hwNextED;
209 static void ohci_dump_intr_mask (char *label, __u32 mask)
211 dbg ("%s: 0x%08x%s%s%s%s%s%s%s%s%s",
214 (mask & OHCI_INTR_MIE) ? " MIE" : "",
215 (mask & OHCI_INTR_OC) ? " OC" : "",
216 (mask & OHCI_INTR_RHSC) ? " RHSC" : "",
217 (mask & OHCI_INTR_FNO) ? " FNO" : "",
218 (mask & OHCI_INTR_UE) ? " UE" : "",
219 (mask & OHCI_INTR_RD) ? " RD" : "",
220 (mask & OHCI_INTR_SF) ? " SF" : "",
221 (mask & OHCI_INTR_WDH) ? " WDH" : "",
222 (mask & OHCI_INTR_SO) ? " SO" : ""
226 static void maybe_print_eds (char *label, __u32 value)
228 ed_t *edp = (ed_t *)value;
231 dbg ("%s %08x", label, value);
232 dbg ("%08x", edp->hwINFO);
233 dbg ("%08x", edp->hwTailP);
234 dbg ("%08x", edp->hwHeadP);
235 dbg ("%08x", edp->hwNextED);
239 static char * hcfs2string (int state)
242 case OHCI_USB_RESET: return "reset";
243 case OHCI_USB_RESUME: return "resume";
244 case OHCI_USB_OPER: return "operational";
245 case OHCI_USB_SUSPEND: return "suspend";
250 /* dump control and status registers */
251 static void ohci_dump_status (ohci_t *controller)
253 struct ohci_regs *regs = controller->regs;
256 temp = readl (®s->revision) & 0xff;
258 dbg ("spec %d.%d", (temp >> 4), (temp & 0x0f));
260 temp = readl (®s->control);
261 dbg ("control: 0x%08x%s%s%s HCFS=%s%s%s%s%s CBSR=%d", temp,
262 (temp & OHCI_CTRL_RWE) ? " RWE" : "",
263 (temp & OHCI_CTRL_RWC) ? " RWC" : "",
264 (temp & OHCI_CTRL_IR) ? " IR" : "",
265 hcfs2string (temp & OHCI_CTRL_HCFS),
266 (temp & OHCI_CTRL_BLE) ? " BLE" : "",
267 (temp & OHCI_CTRL_CLE) ? " CLE" : "",
268 (temp & OHCI_CTRL_IE) ? " IE" : "",
269 (temp & OHCI_CTRL_PLE) ? " PLE" : "",
270 temp & OHCI_CTRL_CBSR
273 temp = readl (®s->cmdstatus);
274 dbg ("cmdstatus: 0x%08x SOC=%d%s%s%s%s", temp,
275 (temp & OHCI_SOC) >> 16,
276 (temp & OHCI_OCR) ? " OCR" : "",
277 (temp & OHCI_BLF) ? " BLF" : "",
278 (temp & OHCI_CLF) ? " CLF" : "",
279 (temp & OHCI_HCR) ? " HCR" : ""
282 ohci_dump_intr_mask ("intrstatus", readl (®s->intrstatus));
283 ohci_dump_intr_mask ("intrenable", readl (®s->intrenable));
285 maybe_print_eds ("ed_periodcurrent", readl (®s->ed_periodcurrent));
287 maybe_print_eds ("ed_controlhead", readl (®s->ed_controlhead));
288 maybe_print_eds ("ed_controlcurrent", readl (®s->ed_controlcurrent));
290 maybe_print_eds ("ed_bulkhead", readl (®s->ed_bulkhead));
291 maybe_print_eds ("ed_bulkcurrent", readl (®s->ed_bulkcurrent));
293 maybe_print_eds ("donehead", readl (®s->donehead));
296 static void ohci_dump_roothub (ohci_t *controller, int verbose)
300 temp = roothub_a (controller);
301 ndp = (temp & RH_A_NDP);
304 dbg ("roothub.a: %08x POTPGT=%d%s%s%s%s%s NDP=%d", temp,
305 ((temp & RH_A_POTPGT) >> 24) & 0xff,
306 (temp & RH_A_NOCP) ? " NOCP" : "",
307 (temp & RH_A_OCPM) ? " OCPM" : "",
308 (temp & RH_A_DT) ? " DT" : "",
309 (temp & RH_A_NPS) ? " NPS" : "",
310 (temp & RH_A_PSM) ? " PSM" : "",
313 temp = roothub_b (controller);
314 dbg ("roothub.b: %08x PPCM=%04x DR=%04x",
316 (temp & RH_B_PPCM) >> 16,
319 temp = roothub_status (controller);
320 dbg ("roothub.status: %08x%s%s%s%s%s%s",
322 (temp & RH_HS_CRWE) ? " CRWE" : "",
323 (temp & RH_HS_OCIC) ? " OCIC" : "",
324 (temp & RH_HS_LPSC) ? " LPSC" : "",
325 (temp & RH_HS_DRWE) ? " DRWE" : "",
326 (temp & RH_HS_OCI) ? " OCI" : "",
327 (temp & RH_HS_LPS) ? " LPS" : ""
331 for (i = 0; i < ndp; i++) {
332 temp = roothub_portstatus (controller, i);
333 dbg ("roothub.portstatus [%d] = 0x%08x%s%s%s%s%s%s%s%s%s%s%s%s",
336 (temp & RH_PS_PRSC) ? " PRSC" : "",
337 (temp & RH_PS_OCIC) ? " OCIC" : "",
338 (temp & RH_PS_PSSC) ? " PSSC" : "",
339 (temp & RH_PS_PESC) ? " PESC" : "",
340 (temp & RH_PS_CSC) ? " CSC" : "",
342 (temp & RH_PS_LSDA) ? " LSDA" : "",
343 (temp & RH_PS_PPS) ? " PPS" : "",
344 (temp & RH_PS_PRS) ? " PRS" : "",
345 (temp & RH_PS_POCI) ? " POCI" : "",
346 (temp & RH_PS_PSS) ? " PSS" : "",
348 (temp & RH_PS_PES) ? " PES" : "",
349 (temp & RH_PS_CCS) ? " CCS" : ""
354 static void ohci_dump (ohci_t *controller, int verbose)
356 dbg ("OHCI controller usb-%s state", controller->slot_name);
358 /* dumps some of the state we know about */
359 ohci_dump_status (controller);
361 ep_print_int_eds (controller, "hcca");
362 dbg ("hcca frame #%04x", controller->hcca->frame_no);
363 ohci_dump_roothub (controller, 1);
369 /*-------------------------------------------------------------------------*
370 * Interface functions (URB)
371 *-------------------------------------------------------------------------*/
373 /* get a transfer request */
375 int sohci_submit_job(struct usb_device *dev, unsigned long pipe, void *buffer,
376 int transfer_len, struct devrequest *setup, int interval)
380 urb_priv_t *purb_priv;
385 /* when controller's hung, permit only roothub cleanup attempts
386 * such as powering down ports */
387 if (ohci->disabled) {
388 err("sohci_submit_job: EPIPE");
392 /* every endpoint has a ed, locate and fill it */
393 if (!(ed = ep_add_ed (dev, pipe))) {
394 err("sohci_submit_job: ENOMEM");
398 /* for the private part of the URB we need the number of TDs (size) */
399 switch (usb_pipetype (pipe)) {
400 case PIPE_BULK: /* one TD for every 4096 Byte */
401 size = (transfer_len - 1) / 4096 + 1;
403 case PIPE_CONTROL: /* 1 TD for setup, 1 for ACK and 1 for every 4096 B */
404 size = (transfer_len == 0)? 2:
405 (transfer_len - 1) / 4096 + 3;
409 if (size >= (N_URB_TD - 1)) {
410 err("need %d TDs, only have %d", size, N_URB_TD);
413 purb_priv = &urb_priv;
414 purb_priv->pipe = pipe;
416 /* fill the private part of the URB */
417 purb_priv->length = size;
419 purb_priv->actual_length = 0;
421 /* allocate the TDs */
422 /* note that td[0] was allocated in ep_add_ed */
423 for (i = 0; i < size; i++) {
424 purb_priv->td[i] = td_alloc (dev);
425 if (!purb_priv->td[i]) {
426 purb_priv->length = i;
427 urb_free_priv (purb_priv);
428 err("sohci_submit_job: ENOMEM");
433 if (ed->state == ED_NEW || (ed->state & ED_DEL)) {
434 urb_free_priv (purb_priv);
435 err("sohci_submit_job: EINVAL");
439 /* link the ed into a chain if is not already */
440 if (ed->state != ED_OPER)
443 /* fill the TDs and link it to the ed */
444 td_submit_job(dev, pipe, buffer, transfer_len, setup, purb_priv, interval);
449 /*-------------------------------------------------------------------------*/
452 /* tell us the current USB frame number */
454 static int sohci_get_current_frame_number (struct usb_device *usb_dev)
456 ohci_t *ohci = &gohci;
458 return m16_swap (ohci->hcca->frame_no);
462 /*-------------------------------------------------------------------------*
463 * ED handling functions
464 *-------------------------------------------------------------------------*/
466 /* link an ed into one of the HC chains */
468 static int ep_link (ohci_t *ohci, ed_t *edi)
470 volatile ed_t *ed = edi;
477 if (ohci->ed_controltail == NULL) {
478 writel ((long)ed, &ohci->regs->ed_controlhead);
480 ohci->ed_controltail->hwNextED = m32_swap (ed);
482 ed->ed_prev = ohci->ed_controltail;
483 if (!ohci->ed_controltail && !ohci->ed_rm_list[0] &&
484 !ohci->ed_rm_list[1] && !ohci->sleeping) {
485 ohci->hc_control |= OHCI_CTRL_CLE;
486 writel (ohci->hc_control, &ohci->regs->control);
488 ohci->ed_controltail = edi;
493 if (ohci->ed_bulktail == NULL) {
494 writel ((long)ed, &ohci->regs->ed_bulkhead);
496 ohci->ed_bulktail->hwNextED = m32_swap (ed);
498 ed->ed_prev = ohci->ed_bulktail;
499 if (!ohci->ed_bulktail && !ohci->ed_rm_list[0] &&
500 !ohci->ed_rm_list[1] && !ohci->sleeping) {
501 ohci->hc_control |= OHCI_CTRL_BLE;
502 writel (ohci->hc_control, &ohci->regs->control);
504 ohci->ed_bulktail = edi;
510 /*-------------------------------------------------------------------------*/
512 /* unlink an ed from one of the HC chains.
513 * just the link to the ed is unlinked.
514 * the link from the ed still points to another operational ed or 0
515 * so the HC can eventually finish the processing of the unlinked ed */
517 static int ep_unlink (ohci_t *ohci, ed_t *ed)
519 ed->hwINFO |= m32_swap (OHCI_ED_SKIP);
523 if (ed->ed_prev == NULL) {
525 ohci->hc_control &= ~OHCI_CTRL_CLE;
526 writel (ohci->hc_control, &ohci->regs->control);
528 writel (m32_swap (*((__u32 *)&ed->hwNextED)), &ohci->regs->ed_controlhead);
530 ed->ed_prev->hwNextED = ed->hwNextED;
532 if (ohci->ed_controltail == ed) {
533 ohci->ed_controltail = ed->ed_prev;
535 ((ed_t *)m32_swap (*((__u32 *)&ed->hwNextED)))->ed_prev = ed->ed_prev;
540 if (ed->ed_prev == NULL) {
542 ohci->hc_control &= ~OHCI_CTRL_BLE;
543 writel (ohci->hc_control, &ohci->regs->control);
545 writel (m32_swap (*((__u32 *)&ed->hwNextED)), &ohci->regs->ed_bulkhead);
547 ed->ed_prev->hwNextED = ed->hwNextED;
549 if (ohci->ed_bulktail == ed) {
550 ohci->ed_bulktail = ed->ed_prev;
552 ((ed_t *)m32_swap (*((__u32 *)&ed->hwNextED)))->ed_prev = ed->ed_prev;
556 ed->state = ED_UNLINK;
561 /*-------------------------------------------------------------------------*/
563 /* add/reinit an endpoint; this should be done once at the usb_set_configuration command,
564 * but the USB stack is a little bit stateless so we do it at every transaction
565 * if the state of the ed is ED_NEW then a dummy td is added and the state is changed to ED_UNLINK
566 * in all other cases the state is left unchanged
567 * the ed info fields are setted anyway even though most of them should not change */
569 static ed_t * ep_add_ed (struct usb_device *usb_dev, unsigned long pipe)
575 ed = ed_ret = &ohci_dev.ed[(usb_pipeendpoint (pipe) << 1) |
576 (usb_pipecontrol (pipe)? 0: usb_pipeout (pipe))];
578 if ((ed->state & ED_DEL) || (ed->state & ED_URB_DEL)) {
579 err("ep_add_ed: pending delete");
580 /* pending delete request */
584 if (ed->state == ED_NEW) {
585 ed->hwINFO = m32_swap (OHCI_ED_SKIP); /* skip ed */
586 /* dummy td; end of td list for ed */
587 td = td_alloc (usb_dev);
588 ed->hwTailP = m32_swap (td);
589 ed->hwHeadP = ed->hwTailP;
590 ed->state = ED_UNLINK;
591 ed->type = usb_pipetype (pipe);
595 ed->hwINFO = m32_swap (usb_pipedevice (pipe)
596 | usb_pipeendpoint (pipe) << 7
597 | (usb_pipeisoc (pipe)? 0x8000: 0)
598 | (usb_pipecontrol (pipe)? 0: (usb_pipeout (pipe)? 0x800: 0x1000))
599 | (usb_dev->speed == USB_SPEED_LOW) << 13
600 | usb_maxpacket (usb_dev, pipe) << 16);
605 /*-------------------------------------------------------------------------*
606 * TD handling functions
607 *-------------------------------------------------------------------------*/
609 /* enqueue next TD for this URB (OHCI spec 5.2.8.2) */
611 static void td_fill (ohci_t *ohci, unsigned int info,
613 struct usb_device *dev, int index, urb_priv_t *urb_priv)
615 volatile td_t *td, *td_pt;
616 #ifdef OHCI_FILL_TRACE
620 if (index > urb_priv->length) {
621 err("index > length");
624 /* use this td as the next dummy */
625 td_pt = urb_priv->td [index];
628 /* fill the old dummy TD */
629 td = urb_priv->td [index] = (td_t *)(m32_swap (urb_priv->ed->hwTailP) & ~0xf);
631 td->ed = urb_priv->ed;
632 td->next_dl_td = NULL;
634 td->data = (__u32)data;
635 #ifdef OHCI_FILL_TRACE
636 if (1 || (usb_pipebulk(urb_priv->pipe) &&
637 usb_pipeout(urb_priv->pipe))) {
638 for (i = 0; i < len; i++)
639 printf("td->data[%d] %#2x\n",i, ((unsigned char *)(td->data+0x80000000))[i]);
645 td->hwINFO = m32_swap (info);
646 td->hwCBP = m32_swap (data);
648 td->hwBE = m32_swap (data + len - 1);
651 td->hwNextTD = m32_swap (td_pt);
652 td->hwPSW [0] = m16_swap (((__u32)data & 0x0FFF) | 0xE000);
654 /* append to queue */
655 td->ed->hwTailP = td->hwNextTD;
658 /*-------------------------------------------------------------------------*/
660 /* prepare all TDs of a transfer */
662 #define kseg_to_phys(x) ((void *)((__u32)(x) - 0x80000000))
664 static void td_submit_job (struct usb_device *dev, unsigned long pipe, void *buffer,
665 int transfer_len, struct devrequest *setup, urb_priv_t *urb, int interval)
667 ohci_t *ohci = &gohci;
668 int data_len = transfer_len;
672 unsigned int toggle = 0;
674 /* OHCI handles the DATA-toggles itself, we just use the USB-toggle bits for reseting */
675 if(usb_gettoggle(dev, usb_pipeendpoint(pipe), usb_pipeout(pipe))) {
676 toggle = TD_T_TOGGLE;
679 usb_settoggle(dev, usb_pipeendpoint(pipe), usb_pipeout(pipe), 1);
683 data = kseg_to_phys(buffer);
687 switch (usb_pipetype (pipe)) {
689 info = usb_pipeout (pipe)?
690 TD_CC | TD_DP_OUT : TD_CC | TD_DP_IN ;
691 while(data_len > 4096) {
692 td_fill (ohci, info | (cnt? TD_T_TOGGLE:toggle), data, 4096, dev, cnt, urb);
693 data += 4096; data_len -= 4096; cnt++;
695 info = usb_pipeout (pipe)?
696 TD_CC | TD_DP_OUT : TD_CC | TD_R | TD_DP_IN ;
697 td_fill (ohci, info | (cnt? TD_T_TOGGLE:toggle), data, data_len, dev, cnt, urb);
701 writel (OHCI_BLF, &ohci->regs->cmdstatus); /* start bulk list */
705 info = TD_CC | TD_DP_SETUP | TD_T_DATA0;
706 td_fill (ohci, info, kseg_to_phys(setup), 8, dev, cnt++, urb);
708 info = usb_pipeout (pipe)?
709 TD_CC | TD_R | TD_DP_OUT | TD_T_DATA1 : TD_CC | TD_R | TD_DP_IN | TD_T_DATA1;
710 /* NOTE: mishandles transfers >8K, some >4K */
711 td_fill (ohci, info, data, data_len, dev, cnt++, urb);
713 info = usb_pipeout (pipe)?
714 TD_CC | TD_DP_IN | TD_T_DATA1: TD_CC | TD_DP_OUT | TD_T_DATA1;
715 td_fill (ohci, info, data, 0, dev, cnt++, urb);
717 writel (OHCI_CLF, &ohci->regs->cmdstatus); /* start Control list */
720 if (urb->length != cnt)
721 dbg("TD LENGTH %d != CNT %d", urb->length, cnt);
724 /*-------------------------------------------------------------------------*
725 * Done List handling functions
726 *-------------------------------------------------------------------------*/
729 /* calculate the transfer length and update the urb */
731 static void dl_transfer_length(td_t * td)
733 __u32 tdINFO, tdBE, tdCBP;
734 urb_priv_t *lurb_priv = &urb_priv;
736 tdINFO = m32_swap (td->hwINFO);
737 tdBE = m32_swap (td->hwBE);
738 tdCBP = m32_swap (td->hwCBP);
741 if (!(usb_pipecontrol(lurb_priv->pipe) &&
742 ((td->index == 0) || (td->index == lurb_priv->length - 1)))) {
745 lurb_priv->actual_length += tdBE - td->data + 1;
747 lurb_priv->actual_length += tdCBP - td->data;
752 /*-------------------------------------------------------------------------*/
754 /* replies to the request have to be on a FIFO basis so
755 * we reverse the reversed done-list */
757 static td_t * dl_reverse_done_list (ohci_t *ohci)
761 td_t *td_list = NULL;
762 urb_priv_t *lurb_priv = NULL;
764 td_list_hc = m32_swap (ohci->hcca->done_head) & 0xfffffff0;
765 ohci->hcca->done_head = 0;
768 td_list = (td_t *)td_list_hc;
770 if (TD_CC_GET (m32_swap (td_list->hwINFO))) {
771 lurb_priv = &urb_priv;
772 dbg(" USB-error/status: %x : %p",
773 TD_CC_GET (m32_swap (td_list->hwINFO)), td_list);
774 if (td_list->ed->hwHeadP & m32_swap (0x1)) {
775 if (lurb_priv && ((td_list->index + 1) < lurb_priv->length)) {
776 td_list->ed->hwHeadP =
777 (lurb_priv->td[lurb_priv->length - 1]->hwNextTD & m32_swap (0xfffffff0)) |
778 (td_list->ed->hwHeadP & m32_swap (0x2));
779 lurb_priv->td_cnt += lurb_priv->length - td_list->index - 1;
781 td_list->ed->hwHeadP &= m32_swap (0xfffffff2);
785 td_list->next_dl_td = td_rev;
787 td_list_hc = m32_swap (td_list->hwNextTD) & 0xfffffff0;
792 /*-------------------------------------------------------------------------*/
795 static int dl_done_list (ohci_t *ohci, td_t *td_list)
797 td_t *td_list_next = NULL;
802 urb_priv_t *lurb_priv;
803 __u32 tdINFO, edHeadP, edTailP;
806 td_list_next = td_list->next_dl_td;
808 lurb_priv = &urb_priv;
809 tdINFO = m32_swap (td_list->hwINFO);
813 dl_transfer_length(td_list);
815 /* error code of transfer */
816 cc = TD_CC_GET (tdINFO);
818 dbg("ConditionCode %#x", cc);
819 stat = cc_to_error[cc];
822 if (ed->state != ED_NEW) {
823 edHeadP = m32_swap (ed->hwHeadP) & 0xfffffff0;
824 edTailP = m32_swap (ed->hwTailP);
826 /* unlink eds if they are not busy */
827 if ((edHeadP == edTailP) && (ed->state == ED_OPER))
828 ep_unlink (ohci, ed);
831 td_list = td_list_next;
836 /*-------------------------------------------------------------------------*
838 *-------------------------------------------------------------------------*/
840 #include <usbroothubdes.h>
842 /* Hub class-specific descriptor is constructed dynamically */
845 /*-------------------------------------------------------------------------*/
847 #define OK(x) len = (x); break
849 #define WR_RH_STAT(x) {info("WR:status %#8x", (x));writel((x), &gohci.regs->roothub.status);}
850 #define WR_RH_PORTSTAT(x) {info("WR:portstatus[%d] %#8x", wIndex-1, (x));writel((x), &gohci.regs->roothub.portstatus[wIndex-1]);}
852 #define WR_RH_STAT(x) writel((x), &gohci.regs->roothub.status)
853 #define WR_RH_PORTSTAT(x) writel((x), &gohci.regs->roothub.portstatus[wIndex-1])
855 #define RD_RH_STAT roothub_status(&gohci)
856 #define RD_RH_PORTSTAT roothub_portstatus(&gohci,wIndex-1)
858 /* request to virtual root hub */
860 int rh_check_port_status(ohci_t *controller)
866 temp = roothub_a (controller);
867 ndp = (temp & RH_A_NDP);
868 for (i = 0; i < ndp; i++) {
869 temp = roothub_portstatus (controller, i);
870 /* check for a device disconnect */
871 if (((temp & (RH_PS_PESC | RH_PS_CSC)) ==
872 (RH_PS_PESC | RH_PS_CSC)) &&
873 ((temp & RH_PS_CCS) == 0)) {
881 static int ohci_submit_rh_msg(struct usb_device *dev, unsigned long pipe,
882 void *buffer, int transfer_len, struct devrequest *cmd)
884 void * data = buffer;
885 int leni = transfer_len;
889 __u8 *data_buf = (__u8 *)datab;
896 urb_priv.actual_length = 0;
897 pkt_print(dev, pipe, buffer, transfer_len, cmd, "SUB(rh)", usb_pipein(pipe));
901 if (usb_pipeint(pipe)) {
902 info("Root-Hub submit IRQ: NOT implemented");
906 bmRType_bReq = cmd->requesttype | (cmd->request << 8);
907 wValue = m16_swap (cmd->value);
908 wIndex = m16_swap (cmd->index);
909 wLength = m16_swap (cmd->length);
911 info("Root-Hub: adr: %2x cmd(%1x): %08x %04x %04x %04x",
912 dev->devnum, 8, bmRType_bReq, wValue, wIndex, wLength);
914 switch (bmRType_bReq) {
915 /* Request Destination:
916 without flags: Device,
917 RH_INTERFACE: interface,
918 RH_ENDPOINT: endpoint,
919 RH_CLASS means HUB here,
920 RH_OTHER | RH_CLASS almost ever means HUB_PORT here
924 *(__u16 *) data_buf = m16_swap (1); OK (2);
925 case RH_GET_STATUS | RH_INTERFACE:
926 *(__u16 *) data_buf = m16_swap (0); OK (2);
927 case RH_GET_STATUS | RH_ENDPOINT:
928 *(__u16 *) data_buf = m16_swap (0); OK (2);
929 case RH_GET_STATUS | RH_CLASS:
930 *(__u32 *) data_buf = m32_swap (
931 RD_RH_STAT & ~(RH_HS_CRWE | RH_HS_DRWE));
933 case RH_GET_STATUS | RH_OTHER | RH_CLASS:
934 *(__u32 *) data_buf = m32_swap (RD_RH_PORTSTAT); OK (4);
936 case RH_CLEAR_FEATURE | RH_ENDPOINT:
938 case (RH_ENDPOINT_STALL): OK (0);
942 case RH_CLEAR_FEATURE | RH_CLASS:
944 case RH_C_HUB_LOCAL_POWER:
946 case (RH_C_HUB_OVER_CURRENT):
947 WR_RH_STAT(RH_HS_OCIC); OK (0);
951 case RH_CLEAR_FEATURE | RH_OTHER | RH_CLASS:
953 case (RH_PORT_ENABLE):
954 WR_RH_PORTSTAT (RH_PS_CCS ); OK (0);
955 case (RH_PORT_SUSPEND):
956 WR_RH_PORTSTAT (RH_PS_POCI); OK (0);
957 case (RH_PORT_POWER):
958 WR_RH_PORTSTAT (RH_PS_LSDA); OK (0);
959 case (RH_C_PORT_CONNECTION):
960 WR_RH_PORTSTAT (RH_PS_CSC ); OK (0);
961 case (RH_C_PORT_ENABLE):
962 WR_RH_PORTSTAT (RH_PS_PESC); OK (0);
963 case (RH_C_PORT_SUSPEND):
964 WR_RH_PORTSTAT (RH_PS_PSSC); OK (0);
965 case (RH_C_PORT_OVER_CURRENT):
966 WR_RH_PORTSTAT (RH_PS_OCIC); OK (0);
967 case (RH_C_PORT_RESET):
968 WR_RH_PORTSTAT (RH_PS_PRSC); OK (0);
972 case RH_SET_FEATURE | RH_OTHER | RH_CLASS:
974 case (RH_PORT_SUSPEND):
975 WR_RH_PORTSTAT (RH_PS_PSS ); OK (0);
976 case (RH_PORT_RESET): /* BUG IN HUP CODE *********/
977 if (RD_RH_PORTSTAT & RH_PS_CCS)
978 WR_RH_PORTSTAT (RH_PS_PRS);
980 case (RH_PORT_POWER):
981 WR_RH_PORTSTAT (RH_PS_PPS ); OK (0);
982 case (RH_PORT_ENABLE): /* BUG IN HUP CODE *********/
983 if (RD_RH_PORTSTAT & RH_PS_CCS)
984 WR_RH_PORTSTAT (RH_PS_PES );
989 case RH_SET_ADDRESS: gohci.rh.devnum = wValue; OK(0);
991 case RH_GET_DESCRIPTOR:
992 switch ((wValue & 0xff00) >> 8) {
993 case (0x01): /* device descriptor */
994 len = min_t(unsigned int,
997 sizeof (root_hub_dev_des),
999 data_buf = root_hub_dev_des; OK(len);
1000 case (0x02): /* configuration descriptor */
1001 len = min_t(unsigned int,
1004 sizeof (root_hub_config_des),
1006 data_buf = root_hub_config_des; OK(len);
1007 case (0x03): /* string descriptors */
1008 if(wValue==0x0300) {
1009 len = min_t(unsigned int,
1012 sizeof (root_hub_str_index0),
1014 data_buf = root_hub_str_index0;
1017 if(wValue==0x0301) {
1018 len = min_t(unsigned int,
1021 sizeof (root_hub_str_index1),
1023 data_buf = root_hub_str_index1;
1027 stat = USB_ST_STALLED;
1031 case RH_GET_DESCRIPTOR | RH_CLASS:
1033 __u32 temp = roothub_a (&gohci);
1035 data_buf [0] = 9; /* min length; */
1036 data_buf [1] = 0x29;
1037 data_buf [2] = temp & RH_A_NDP;
1039 if (temp & RH_A_PSM) /* per-port power switching? */
1040 data_buf [3] |= 0x1;
1041 if (temp & RH_A_NOCP) /* no overcurrent reporting? */
1042 data_buf [3] |= 0x10;
1043 else if (temp & RH_A_OCPM) /* per-port overcurrent reporting? */
1044 data_buf [3] |= 0x8;
1046 /* corresponds to data_buf[4-7] */
1048 data_buf [5] = (temp & RH_A_POTPGT) >> 24;
1049 temp = roothub_b (&gohci);
1050 data_buf [7] = temp & RH_B_DR;
1051 if (data_buf [2] < 7) {
1052 data_buf [8] = 0xff;
1055 data_buf [8] = (temp & RH_B_DR) >> 8;
1056 data_buf [10] = data_buf [9] = 0xff;
1059 len = min_t(unsigned int, leni,
1060 min_t(unsigned int, data_buf [0], wLength));
1064 case RH_GET_CONFIGURATION: *(__u8 *) data_buf = 0x01; OK (1);
1066 case RH_SET_CONFIGURATION: WR_RH_STAT (0x10000); OK (0);
1069 dbg ("unsupported root hub command");
1070 stat = USB_ST_STALLED;
1074 ohci_dump_roothub (&gohci, 1);
1079 len = min_t(int, len, leni);
1080 if (data != data_buf)
1081 memcpy (data, data_buf, len);
1087 urb_priv.actual_length = transfer_len;
1088 pkt_print(dev, pipe, buffer, transfer_len, cmd, "RET(rh)", 0/*usb_pipein(pipe)*/);
1096 /*-------------------------------------------------------------------------*/
1098 /* common code for handling submit messages - used for all but root hub */
1100 int submit_common_msg(struct usb_device *dev, unsigned long pipe, void *buffer,
1101 int transfer_len, struct devrequest *setup, int interval)
1104 int maxsize = usb_maxpacket(dev, pipe);
1107 /* device pulled? Shortcut the action. */
1108 if (devgone == dev) {
1109 dev->status = USB_ST_CRC_ERR;
1114 urb_priv.actual_length = 0;
1115 pkt_print(dev, pipe, buffer, transfer_len, setup, "SUB", usb_pipein(pipe));
1120 err("submit_common_message: pipesize for pipe %lx is zero",
1125 if (sohci_submit_job(dev, pipe, buffer, transfer_len, setup, interval) < 0) {
1126 err("sohci_submit_job failed");
1131 /* ohci_dump_status(&gohci); */
1133 /* allow more time for a BULK device to react - some are slow */
1134 #define BULK_TO 5000 /* timeout in milliseconds */
1135 if (usb_pipebulk(pipe))
1141 /* wait for it to complete */
1143 /* check whether the controller is done */
1144 stat = hc_interrupt();
1146 stat = USB_ST_CRC_ERR;
1149 if (stat >= 0 && stat != 0xff) {
1150 /* 0xff is returned for an SF-interrupt */
1154 udelay(250); /* mdelay(1); */
1156 err("CTL:TIMEOUT ");
1157 stat = USB_ST_CRC_ERR;
1161 /* we got an Root Hub Status Change interrupt */
1164 ohci_dump_roothub (&gohci, 1);
1168 timeout = rh_check_port_status(&gohci);
1170 #if 0 /* this does nothing useful, but leave it here in case that changes */
1171 /* the called routine adds 1 to the passed value */
1172 usb_hub_port_connect_change(gohci.rh.dev, timeout - 1);
1176 * This is potentially dangerous because it assumes
1177 * that only one device is ever plugged in!
1184 dev->act_len = transfer_len;
1187 pkt_print(dev, pipe, buffer, transfer_len, setup, "RET(ctlr)", usb_pipein(pipe));
1192 /* free TDs in urb_priv */
1193 urb_free_priv (&urb_priv);
1197 /* submit routines called from usb.c */
1198 int submit_bulk_msg(struct usb_device *dev, unsigned long pipe, void *buffer,
1201 info("submit_bulk_msg");
1202 return submit_common_msg(dev, pipe, buffer, transfer_len, NULL, 0);
1205 int submit_control_msg(struct usb_device *dev, unsigned long pipe, void *buffer,
1206 int transfer_len, struct devrequest *setup)
1208 int maxsize = usb_maxpacket(dev, pipe);
1210 info("submit_control_msg");
1212 urb_priv.actual_length = 0;
1213 pkt_print(dev, pipe, buffer, transfer_len, setup, "SUB", usb_pipein(pipe));
1218 err("submit_control_message: pipesize for pipe %lx is zero",
1222 if (((pipe >> 8) & 0x7f) == gohci.rh.devnum) {
1224 /* root hub - redirect */
1225 return ohci_submit_rh_msg(dev, pipe, buffer, transfer_len,
1229 return submit_common_msg(dev, pipe, buffer, transfer_len, setup, 0);
1232 int submit_int_msg(struct usb_device *dev, unsigned long pipe, void *buffer,
1233 int transfer_len, int interval)
1235 info("submit_int_msg");
1239 /*-------------------------------------------------------------------------*
1241 *-------------------------------------------------------------------------*/
1243 /* reset the HC and BUS */
1245 static int hc_reset (ohci_t *ohci)
1248 int smm_timeout = 50; /* 0,5 sec */
1250 if (readl (&ohci->regs->control) & OHCI_CTRL_IR) { /* SMM owns the HC */
1251 writel (OHCI_OCR, &ohci->regs->cmdstatus); /* request ownership */
1252 info("USB HC TakeOver from SMM");
1253 while (readl (&ohci->regs->control) & OHCI_CTRL_IR) {
1255 if (--smm_timeout == 0) {
1256 err("USB HC TakeOver failed!");
1262 /* Disable HC interrupts */
1263 writel (OHCI_INTR_MIE, &ohci->regs->intrdisable);
1265 dbg("USB HC reset_hc usb-%s: ctrl = 0x%X ;",
1267 readl (&ohci->regs->control));
1269 /* Reset USB (needed by some controllers) */
1270 writel (0, &ohci->regs->control);
1272 /* HC Reset requires max 10 us delay */
1273 writel (OHCI_HCR, &ohci->regs->cmdstatus);
1274 while ((readl (&ohci->regs->cmdstatus) & OHCI_HCR) != 0) {
1275 if (--timeout == 0) {
1276 err("USB HC reset timed out!");
1284 /*-------------------------------------------------------------------------*/
1286 /* Start an OHCI controller, set the BUS operational
1288 * connect the virtual root hub */
1290 static int hc_start (ohci_t * ohci)
1293 unsigned int fminterval;
1297 /* Tell the controller where the control and bulk lists are
1298 * The lists are empty now. */
1300 writel (0, &ohci->regs->ed_controlhead);
1301 writel (0, &ohci->regs->ed_bulkhead);
1303 writel ((__u32)ohci->hcca, &ohci->regs->hcca); /* a reset clears this */
1305 fminterval = 0x2edf;
1306 writel ((fminterval * 9) / 10, &ohci->regs->periodicstart);
1307 fminterval |= ((((fminterval - 210) * 6) / 7) << 16);
1308 writel (fminterval, &ohci->regs->fminterval);
1309 writel (0x628, &ohci->regs->lsthresh);
1311 /* start controller operations */
1312 ohci->hc_control = OHCI_CONTROL_INIT | OHCI_USB_OPER;
1314 writel (ohci->hc_control, &ohci->regs->control);
1316 /* disable all interrupts */
1317 mask = (OHCI_INTR_SO | OHCI_INTR_WDH | OHCI_INTR_SF | OHCI_INTR_RD |
1318 OHCI_INTR_UE | OHCI_INTR_FNO | OHCI_INTR_RHSC |
1319 OHCI_INTR_OC | OHCI_INTR_MIE);
1320 writel (mask, &ohci->regs->intrdisable);
1321 /* clear all interrupts */
1322 mask &= ~OHCI_INTR_MIE;
1323 writel (mask, &ohci->regs->intrstatus);
1324 /* Choose the interrupts we care about now - but w/o MIE */
1325 mask = OHCI_INTR_RHSC | OHCI_INTR_UE | OHCI_INTR_WDH | OHCI_INTR_SO;
1326 writel (mask, &ohci->regs->intrenable);
1329 /* required for AMD-756 and some Mac platforms */
1330 writel ((roothub_a (ohci) | RH_A_NPS) & ~RH_A_PSM,
1331 &ohci->regs->roothub.a);
1332 writel (RH_HS_LPSC, &ohci->regs->roothub.status);
1333 #endif /* OHCI_USE_NPS */
1335 /* POTPGT delay is bits 24-31, in 2 ms units. */
1336 mdelay ((roothub_a (ohci) >> 23) & 0x1fe);
1338 /* connect the virtual root hub */
1339 ohci->rh.devnum = 0;
1344 /*-------------------------------------------------------------------------*/
1346 /* an interrupt happens */
1351 ohci_t *ohci = &gohci;
1352 struct ohci_regs *regs = ohci->regs;
1356 if ((ohci->hcca->done_head != 0) && !(m32_swap (ohci->hcca->done_head) & 0x01)) {
1357 ints = OHCI_INTR_WDH;
1359 ints = readl (®s->intrstatus);
1362 /* dbg("Interrupt: %x frame: %x", ints, le16_to_cpu (ohci->hcca->frame_no)); */
1364 if (ints & OHCI_INTR_RHSC) {
1368 if (ints & OHCI_INTR_UE) {
1370 err ("OHCI Unrecoverable Error, controller usb-%s disabled",
1372 /* e.g. due to PCI Master/Target Abort */
1375 ohci_dump (ohci, 1);
1379 /* FIXME: be optimistic, hope that bug won't repeat often. */
1380 /* Make some non-interrupt context restart the controller. */
1381 /* Count and limit the retries though; either hardware or */
1382 /* software errors can go forever... */
1387 if (ints & OHCI_INTR_WDH) {
1389 writel (OHCI_INTR_WDH, ®s->intrdisable);
1390 stat = dl_done_list (&gohci, dl_reverse_done_list (&gohci));
1391 writel (OHCI_INTR_WDH, ®s->intrenable);
1394 if (ints & OHCI_INTR_SO) {
1395 dbg("USB Schedule overrun\n");
1396 writel (OHCI_INTR_SO, ®s->intrenable);
1400 /* FIXME: this assumes SOF (1/ms) interrupts don't get lost... */
1401 if (ints & OHCI_INTR_SF) {
1402 unsigned int frame = m16_swap (ohci->hcca->frame_no) & 1;
1404 writel (OHCI_INTR_SF, ®s->intrdisable);
1405 if (ohci->ed_rm_list[frame] != NULL)
1406 writel (OHCI_INTR_SF, ®s->intrenable);
1410 writel (ints, ®s->intrstatus);
1414 /*-------------------------------------------------------------------------*/
1416 /*-------------------------------------------------------------------------*/
1418 /* De-allocate all resources.. */
1420 static void hc_release_ohci (ohci_t *ohci)
1422 dbg ("USB HC release ohci usb-%s", ohci->slot_name);
1424 if (!ohci->disabled)
1428 /*-------------------------------------------------------------------------*/
1430 #define __read_32bit_c0_register(source, sel) \
1433 __asm__ __volatile__( \
1434 "mfc0\t%0, " #source "\n\t" \
1437 __asm__ __volatile__( \
1438 ".set\tmips32\n\t" \
1439 "mfc0\t%0, " #source ", " #sel "\n\t" \
1445 #define read_c0_prid() __read_32bit_c0_register($15, 0)
1448 * low level initalisation routine, called from usb.c
1450 static char ohci_inited = 0;
1452 int usb_lowlevel_init(int index, enum usb_init_type init, void **controller)
1455 u32 sys_freqctrl, sys_clksrc;
1456 u32 prid = read_c0_prid();
1458 dbg("in usb_lowlevel_init\n");
1460 /* zero and disable FREQ2 */
1461 sys_freqctrl = au_readl(SYS_FREQCTRL0);
1462 sys_freqctrl &= ~0xFFF00000;
1463 au_writel(sys_freqctrl, SYS_FREQCTRL0);
1465 /* zero and disable USBH/USBD clocks */
1466 sys_clksrc = au_readl(SYS_CLKSRC);
1467 sys_clksrc &= ~0x00007FE0;
1468 au_writel(sys_clksrc, SYS_CLKSRC);
1470 sys_freqctrl = au_readl(SYS_FREQCTRL0);
1471 sys_freqctrl &= ~0xFFF00000;
1473 sys_clksrc = au_readl(SYS_CLKSRC);
1474 sys_clksrc &= ~0x00007FE0;
1476 switch (prid & 0x000000FF) {
1480 /* CPU core freq to 48MHz to slow it way down... */
1481 au_writel(4, SYS_CPUPLL);
1484 * Setup 48MHz FREQ2 from CPUPLL for USB Host
1486 /* FRDIV2=3 -> div by 8 of 384MHz -> 48MHz */
1487 sys_freqctrl |= ((3<<22) | (1<<21) | (0<<20));
1488 au_writel(sys_freqctrl, SYS_FREQCTRL0);
1490 /* CPU core freq to 384MHz */
1491 au_writel(0x20, SYS_CPUPLL);
1493 printf("Au1000: 48MHz OHCI workaround enabled\n");
1496 default: /* HC and newer */
1497 /* FREQ2 = aux/2 = 48 MHz */
1498 sys_freqctrl |= ((0<<22) | (1<<21) | (1<<20));
1499 au_writel(sys_freqctrl, SYS_FREQCTRL0);
1504 * Route 48MHz FREQ2 into USB Host and/or Device
1506 sys_clksrc |= ((4<<12) | (0<<11) | (0<<10));
1507 au_writel(sys_clksrc, SYS_CLKSRC);
1509 /* configure pins GPIO[14:9] as GPIO */
1510 pin_func = au_readl(SYS_PINFUNC) & (u32)(~0x8080);
1512 au_writel(pin_func, SYS_PINFUNC);
1513 au_writel(0x2800, SYS_TRIOUTCLR);
1514 au_writel(0x0030, SYS_OUTPUTCLR);
1516 dbg("OHCI board setup complete\n");
1518 /* enable host controller */
1519 au_writel(USBH_ENABLE_CE, USB_HOST_CONFIG);
1521 au_writel(USBH_ENABLE_INIT, USB_HOST_CONFIG);
1524 /* wait for reset complete (read register twice; see au1500 errata) */
1525 while (au_readl(USB_HOST_CONFIG),
1526 !(au_readl(USB_HOST_CONFIG) & USBH_ENABLE_RD))
1529 dbg("OHCI clock running\n");
1531 memset (&gohci, 0, sizeof (ohci_t));
1532 memset (&urb_priv, 0, sizeof (urb_priv_t));
1534 /* align the storage */
1535 if ((__u32)&ghcca[0] & 0xff) {
1536 err("HCCA not aligned!!");
1540 info("aligned ghcca %p", phcca);
1541 memset(&ohci_dev, 0, sizeof(struct ohci_device));
1542 if ((__u32)&ohci_dev.ed[0] & 0x7) {
1543 err("EDs not aligned!!");
1546 memset(gtd, 0, sizeof(td_t) * (NUM_TD + 1));
1547 if ((__u32)gtd & 0x7) {
1548 err("TDs not aligned!!");
1553 memset (phcca, 0, sizeof (struct ohci_hcca));
1558 gohci.regs = (struct ohci_regs *)(USB_OHCI_BASE | 0xA0000000);
1561 gohci.slot_name = "au1x00";
1563 dbg("OHCI revision: 0x%08x\n"
1564 " RH: a: 0x%08x b: 0x%08x\n",
1565 readl(&gohci.regs->revision),
1566 readl(&gohci.regs->roothub.a), readl(&gohci.regs->roothub.b));
1568 if (hc_reset (&gohci) < 0)
1571 /* FIXME this is a second HC reset; why?? */
1572 writel (gohci.hc_control = OHCI_USB_RESET, &gohci.regs->control);
1575 if (hc_start (&gohci) < 0)
1579 ohci_dump (&gohci, 1);
1587 err("OHCI initialization error\n");
1588 hc_release_ohci (&gohci);
1589 /* Initialization failed */
1590 au_writel(readl(USB_HOST_CONFIG) & ~USBH_ENABLE_CE, USB_HOST_CONFIG);
1594 int usb_lowlevel_stop(int index)
1596 /* this gets called really early - before the controller has */
1597 /* even been initialized! */
1600 /* TODO release any interrupts, etc. */
1601 /* call hc_release_ohci() here ? */
1603 /* may not want to do this */
1605 au_writel(readl(USB_HOST_CONFIG) & ~USBH_ENABLE_CE, USB_HOST_CONFIG);
1609 #endif /* CONFIG_USB_OHCI */