2 # Copyright (C) 2010 Eric C. Cooper <ecc@cmu.edu>
4 # Based on sheevaplug/kwbimage.cfg originally written by
5 # Prafulla Wadaskar <prafulla@marvell.com>
7 # Marvell Semiconductor <www.marvell.com>
9 # SPDX-License-Identifier: GPL-2.0+
11 # Refer doc/README.kwbimage for more details about how-to configure
12 # and create kirkwood boot image
15 # Boot Media configurations
20 # SOC registers configuration using bootrom header extension
21 # Maximum KWBIMAGE_MAX_CONFIG configurations allowed
23 # Configure RGMII-0 interface pad voltage to 1.8V
24 DATA 0xFFD100e0 0x1b1b1b9b
26 #Dram initalization for SINGLE x16 CL=5 @ 400MHz
27 DATA 0xFFD01400 0x43000c30 # DDR Configuration register
28 # bit13-0: 0xc30 (3120 DDR2 clks refresh rate)
30 # bit24: 1= enable exit self refresh mode on DDR access
35 DATA 0xFFD01404 0x37543000 # DDR Controller Control Low
36 # bit 4: 0=addr/cmd in smame cycle
37 # bit 5: 0=clk is driven during self refresh, we don't care for APX
38 # bit 6: 0=use recommended falling edge of clk for addr/cmd
39 # bit14: 0=input buffer always powered up
40 # bit18: 1=cpu lock transaction enabled
41 # bit23-20: 5=recommended value for CL=5 and STARTBURST_DEL disabled bit31=0
42 # bit27-24: 7= CL+2, STARTBURST sample stages, for freqs 400MHz, unbuffered DIMM
43 # bit30-28: 3 required
44 # bit31: 0=no additional STARTBURST delay
46 DATA 0xFFD01408 0x22125451 # DDR Timing (Low) (active cycles value +1)
57 DATA 0xFFD0140C 0x00000a33 # DDR Timing (High)
62 # bit31-13: zero required
64 DATA 0xFFD01410 0x0000000d # DDR Address Control
65 # bit1-0: 00, Cs0width=x8
66 # bit3-2: 11, Cs0size=1Gb
67 # bit5-4: 00, Cs1width=nonexistent
68 # bit7-6: 00, Cs1size =nonexistent
69 # bit9-8: 00, Cs2width=nonexistent
70 # bit11-10: 00, Cs2size =nonexistent
71 # bit13-12: 00, Cs3width=nonexistent
72 # bit15-14: 00, Cs3size =nonexistent
73 # bit16: 0, Cs0AddrSel
74 # bit17: 0, Cs1AddrSel
75 # bit18: 0, Cs2AddrSel
76 # bit19: 0, Cs3AddrSel
77 # bit31-20: 0 required
79 DATA 0xFFD01414 0x00000000 # DDR Open Pages Control
80 # bit0: 0, OpenPage enabled
83 DATA 0xFFD01418 0x00000000 # DDR Operation
84 # bit3-0: 0x0, DDR cmd
87 DATA 0xFFD0141C 0x00000C52 # DDR Mode
88 # bit2-0: 2, BurstLen=2 required
89 # bit3: 0, BurstType=0 required
91 # bit7: 0, TestMode=0 normal
92 # bit8: 0, DLL reset=0 normal
93 # bit11-9: 6, auto-precharge write recovery ????????????
94 # bit12: 0, PD must be zero
95 # bit31-13: 0 required
97 DATA 0xFFD01420 0x00000040 # DDR Extended Mode
98 # bit0: 0, DDR DLL enabled
99 # bit1: 0, DDR drive strenght normal
100 # bit2: 0, DDR ODT control lsd (disabled)
101 # bit5-3: 000, required
102 # bit6: 1, DDR ODT control msb, (disabled)
103 # bit9-7: 000, required
104 # bit10: 0, differential DQS enabled
106 # bit12: 0, DDR output buffer enabled
107 # bit31-13: 0 required
109 DATA 0xFFD01424 0x0000F17F # DDR Controller Control High
110 # bit2-0: 111, required
111 # bit3 : 1 , MBUS Burst Chop disabled
112 # bit6-4: 111, required
114 # bit8 : 1 , add writepath sample stage, must be 1 for DDR freq >= 300MHz
115 # bit9 : 0 , no half clock cycle addition to dataout
116 # bit10 : 0 , 1/4 clock cycle skew enabled for addr/ctl signals
117 # bit11 : 0 , 1/4 clock cycle skew disabled for write mesh
118 # bit15-12: 1111 required
119 # bit31-16: 0 required
121 DATA 0xFFD01428 0x00085520 # DDR2 ODT Read Timing (default values)
122 DATA 0xFFD0147C 0x00008552 # DDR2 ODT Write Timing (default values)
124 DATA 0xFFD01500 0x00000000 # CS[0]n Base address to 0x0
125 DATA 0xFFD01504 0x07FFFFF1 # CS[0]n Size
126 # bit0: 1, Window enabled
127 # bit1: 0, Write Protect disabled
128 # bit3-2: 00, CS0 hit selected
129 # bit23-4: ones, required
130 # bit31-24: 0x07, Size (i.e. 128MB)
132 DATA 0xFFD01508 0x10000000 # CS[1]n Base address to 256Mb
133 DATA 0xFFD0150C 0x00000000 # CS[1]n Size, window disabled
135 DATA 0xFFD01514 0x00000000 # CS[2]n Size, window disabled
136 DATA 0xFFD0151C 0x00000000 # CS[3]n Size, window disabled
138 DATA 0xFFD01494 0x00030000 # DDR ODT Control (Low)
139 DATA 0xFFD01498 0x00000000 # DDR ODT Control (High)
140 # bit1-0: 00, ODT0 controlled by ODT Control (low) register above
141 # bit3-2: 01, ODT1 active NEVER!
142 # bit31-4: zero, required
144 DATA 0xFFD0149C 0x0000E803 # CPU ODT Control
145 DATA 0xFFD01480 0x00000001 # DDR Initialization Control
146 #bit0=1, enable DDR init upon this register write
148 # End of Header extension