2 =======================
4 Khadas VIM is an Open Source DIY Box manufactured by Shenzhen Tomato
5 Technology Co., Ltd with the following specifications:
7 - Amlogic S905x ARM Cortex-A53 quad-core SoC @ 2GHz
11 - HDMI 2.0 4K/60Hz display
13 - 2 x USB 2.0 Host, 1 x USB 2.0 Type-C OTG
16 - SDIO Wifi Module, Bluetooth
17 - Two channels IR receiver
19 Currently the u-boot port supports the following devices:
28 > export CROSS_COMPILE=aarch64-none-elf-
29 > make khadas-vim_defconfig
35 Amlogic doesn't provide sources for the firmware and for tools needed
36 to create the bootloader image, so it is necessary to obtain them from
37 the git tree published by the board vendor:
39 > wget https://releases.linaro.org/archive/13.11/components/toolchain/binaries/gcc-linaro-aarch64-none-elf-4.8-2013.11_linux.tar.xz
40 > wget https://releases.linaro.org/archive/13.11/components/toolchain/binaries/gcc-linaro-arm-none-eabi-4.8-2013.11_linux.tar.xz
41 > tar xvfJ gcc-linaro-aarch64-none-elf-4.8-2013.11_linux.tar.xz
42 > tar xvfJ gcc-linaro-arm-none-eabi-4.8-2013.11_linux.tar.xz
43 > export PATH=$PWD/gcc-linaro-aarch64-none-elf-4.8-2013.11_linux/bin:$PWD/gcc-linaro-arm-none-eabi-4.8-2013.11_linux/bin:$PATH
44 > git clone https://github.com/khadas/u-boot -b Vim vim-u-boot
48 > export FIPDIR=$PWD/fip
50 Go back to mainline U-Boot source tree then :
53 > cp $FIPDIR/gxl/bl2.bin fip/
54 > cp $FIPDIR/gxl/acs.bin fip/
55 > cp $FIPDIR/gxl/bl21.bin fip/
56 > cp $FIPDIR/gxl/bl30.bin fip/
57 > cp $FIPDIR/gxl/bl301.bin fip/
58 > cp $FIPDIR/gxl/bl31.img fip/
59 > cp u-boot.bin fip/bl33.bin
61 > $FIPDIR/blx_fix.sh \
70 > $FIPDIR/acs_tool.pyc fip/bl2.bin fip/bl2_acs.bin fip/acs.bin 0
72 > $FIPDIR/blx_fix.sh \
81 > $FIPDIR/gxl/aml_encrypt_gxl --bl3enc --input fip/bl30_new.bin
82 > $FIPDIR/gxl/aml_encrypt_gxl --bl3enc --input fip/bl31.img
83 > $FIPDIR/gxl/aml_encrypt_gxl --bl3enc --input fip/bl33.bin
84 > $FIPDIR/gxl/aml_encrypt_gxl --bl2sig --input fip/bl2_new.bin --output fip/bl2.n.bin.sig
85 > $FIPDIR/gxl/aml_encrypt_gxl --bootmk \
86 --output fip/u-boot.bin \
87 --bl2 fip/bl2.n.bin.sig \
88 --bl30 fip/bl30_new.bin.enc \
89 --bl31 fip/bl31.img.enc \
90 --bl33 fip/bl33.bin.enc
92 and then write the image to SD with:
94 > DEV=/dev/your_sd_device
95 > dd if=fip/u-boot.bin.sd.bin of=$DEV conv=fsync,notrunc bs=512 skip=1 seek=1
96 > dd if=fip/u-boot.bin.sd.bin of=$DEV conv=fsync,notrunc bs=1 count=444