git.sur5r.net Git - u-boot/blob - board/atmel/at91sam9261ek/at91sam9261ek.c

   1 /*
   2  * (C) Copyright 2007-2008
   3  * Stelian Pop <stelian@popies.net>
   4  * Lead Tech Design <www.leadtechdesign.com>
   5  *
   6  * SPDX-License-Identifier:     GPL-2.0+
   7  */
   8
   9 #include <common.h>
  10 #include <debug_uart.h>
  11 #include <asm/io.h>
  12 #include <asm/arch/at91sam9261.h>
  13 #include <asm/arch/at91sam9261_matrix.h>
  14 #include <asm/arch/at91sam9_smc.h>
  15 #include <asm/arch/at91_common.h>
  16 #include <asm/arch/at91_rstc.h>
  17 #include <asm/arch/clk.h>
  18 #include <asm/arch/gpio.h>
  19 #include <lcd.h>
  20 #include <atmel_lcdc.h>
  21 #if defined(CONFIG_RESET_PHY_R) && defined(CONFIG_DRIVER_DM9000)
  22 #include <net.h>
  23 #include <netdev.h>
  24 #endif
  25 #include <asm/mach-types.h>
  26
  27 DECLARE_GLOBAL_DATA_PTR;
  28
  29 /* ------------------------------------------------------------------------- */
  30 /*
  31  * Miscelaneous platform dependent initialisations
  32  */
  33
  34 #ifdef CONFIG_CMD_NAND
  35 static void at91sam9261ek_nand_hw_init(void)
  36 {
  37         struct at91_smc *smc = (struct at91_smc *)ATMEL_BASE_SMC;
  38         struct at91_matrix *matrix = (struct at91_matrix *)ATMEL_BASE_MATRIX;
  39         unsigned long csa;
  40
  41         /* Enable CS3 */
  42         csa = readl(&matrix->ebicsa);
  43         csa |= AT91_MATRIX_CS3A_SMC_SMARTMEDIA;
  44
  45         writel(csa, &matrix->ebicsa);
  46
  47         /* Configure SMC CS3 for NAND/SmartMedia */
  48 #ifdef CONFIG_AT91SAM9G10EK
  49         writel(AT91_SMC_SETUP_NWE(2) | AT91_SMC_SETUP_NCS_WR(0) |
  50                 AT91_SMC_SETUP_NRD(2) | AT91_SMC_SETUP_NCS_RD(0),
  51                 &smc->cs[3].setup);
  52         writel(AT91_SMC_PULSE_NWE(3) | AT91_SMC_PULSE_NCS_WR(7) |
  53                 AT91_SMC_PULSE_NRD(3) | AT91_SMC_PULSE_NCS_RD(7),
  54                 &smc->cs[3].pulse);
  55         writel(AT91_SMC_CYCLE_NWE(7) | AT91_SMC_CYCLE_NRD(7),
  56                 &smc->cs[3].cycle);
  57 #else
  58         writel(AT91_SMC_SETUP_NWE(1) | AT91_SMC_SETUP_NCS_WR(0) |
  59                 AT91_SMC_SETUP_NRD(1) | AT91_SMC_SETUP_NCS_RD(0),
  60                 &smc->cs[3].setup);
  61         writel(AT91_SMC_PULSE_NWE(3) | AT91_SMC_PULSE_NCS_WR(3) |
  62                 AT91_SMC_PULSE_NRD(3) | AT91_SMC_PULSE_NCS_RD(3),
  63                 &smc->cs[3].pulse);
  64         writel(AT91_SMC_CYCLE_NWE(5) | AT91_SMC_CYCLE_NRD(5),
  65                 &smc->cs[3].cycle);
  66 #endif
  67         writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE |
  68                        AT91_SMC_MODE_EXNW_DISABLE |
  69 #ifdef CONFIG_SYS_NAND_DBW_16
  70                        AT91_SMC_MODE_DBW_16 |
  71 #else /* CONFIG_SYS_NAND_DBW_8 */
  72                        AT91_SMC_MODE_DBW_8 |
  73 #endif
  74                        AT91_SMC_MODE_TDF_CYCLE(2),
  75                        &smc->cs[3].mode);
  76
  77         at91_periph_clk_enable(ATMEL_ID_PIOC);
  78
  79         /* Configure RDY/BSY */
  80         at91_set_gpio_input(CONFIG_SYS_NAND_READY_PIN, 1);
  81
  82         /* Enable NandFlash */
  83         at91_set_gpio_output(CONFIG_SYS_NAND_ENABLE_PIN, 1);
  84
  85         at91_set_A_periph(AT91_PIN_PC0, 0);     /* NANDOE */
  86         at91_set_A_periph(AT91_PIN_PC1, 0);     /* NANDWE */
  87 }
  88 #endif
  89
  90 #ifdef CONFIG_DRIVER_DM9000
  91 static void at91sam9261ek_dm9000_hw_init(void)
  92 {
  93         struct at91_smc *smc = (struct at91_smc *)ATMEL_BASE_SMC;
  94
  95         /* Configure SMC CS2 for DM9000 */
  96 #ifdef CONFIG_AT91SAM9G10EK
  97         writel(AT91_SMC_SETUP_NWE(3) | AT91_SMC_SETUP_NCS_WR(0) |
  98                 AT91_SMC_SETUP_NRD(3) | AT91_SMC_SETUP_NCS_RD(0),
  99                 &smc->cs[2].setup);
 100         writel(AT91_SMC_PULSE_NWE(6) | AT91_SMC_PULSE_NCS_WR(8) |
 101                 AT91_SMC_PULSE_NRD(6) | AT91_SMC_PULSE_NCS_RD(8),
 102                 &smc->cs[2].pulse);
 103         writel(AT91_SMC_CYCLE_NWE(20) | AT91_SMC_CYCLE_NRD(20),
 104                 &smc->cs[2].cycle);
 105         writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE |
 106                        AT91_SMC_MODE_EXNW_DISABLE |
 107                        AT91_SMC_MODE_BAT | AT91_SMC_MODE_DBW_16 |
 108                        AT91_SMC_MODE_TDF_CYCLE(1),
 109                        &smc->cs[2].mode);
 110 #else
 111         writel(AT91_SMC_SETUP_NWE(3) | AT91_SMC_SETUP_NCS_WR(0) |
 112                 AT91_SMC_SETUP_NRD(2) | AT91_SMC_SETUP_NCS_RD(0),
 113                 &smc->cs[2].setup);
 114         writel(AT91_SMC_PULSE_NWE(4) | AT91_SMC_PULSE_NCS_WR(8) |
 115                 AT91_SMC_PULSE_NRD(4) | AT91_SMC_PULSE_NCS_RD(8),
 116                 &smc->cs[2].pulse);
 117         writel(AT91_SMC_CYCLE_NWE(16) | AT91_SMC_CYCLE_NRD(16),
 118                 &smc->cs[2].cycle);
 119         writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE |
 120                        AT91_SMC_MODE_EXNW_DISABLE |
 121                        AT91_SMC_MODE_BAT | AT91_SMC_MODE_DBW_16 |
 122                        AT91_SMC_MODE_TDF_CYCLE(1),
 123                        &smc->cs[2].mode);
 124 #endif
 125
 126         /* Configure Reset signal as output */
 127         at91_set_gpio_output(AT91_PIN_PC10, 0);
 128
 129         /* Configure Interrupt pin as input, no pull-up */
 130         at91_set_gpio_input(AT91_PIN_PC11, 0);
 131 }
 132 #endif
 133
 134 #ifdef CONFIG_LCD
 135 vidinfo_t panel_info = {
 136         .vl_col =               240,
 137         .vl_row =               320,
 138         .vl_clk =               4965000,
 139         .vl_sync =              ATMEL_LCDC_INVLINE_INVERTED |
 140                                 ATMEL_LCDC_INVFRAME_INVERTED,
 141         .vl_bpix =              3,
 142         .vl_tft =               1,
 143         .vl_hsync_len =         5,
 144         .vl_left_margin =       1,
 145         .vl_right_margin =      33,
 146         .vl_vsync_len =         1,
 147         .vl_upper_margin =      1,
 148         .vl_lower_margin =      0,
 149         .mmio =                 ATMEL_BASE_LCDC,
 150 };
 151
 152 void lcd_enable(void)
 153 {
 154         at91_set_gpio_value(AT91_PIN_PA12, 0);  /* power up */
 155 }
 156
 157 void lcd_disable(void)
 158 {
 159         at91_set_gpio_value(AT91_PIN_PA12, 1);  /* power down */
 160 }
 161
 162 static void at91sam9261ek_lcd_hw_init(void)
 163 {
 164         at91_set_A_periph(AT91_PIN_PB1, 0);     /* LCDHSYNC */
 165         at91_set_A_periph(AT91_PIN_PB2, 0);     /* LCDDOTCK */
 166         at91_set_A_periph(AT91_PIN_PB3, 0);     /* LCDDEN */
 167         at91_set_A_periph(AT91_PIN_PB4, 0);     /* LCDCC */
 168         at91_set_A_periph(AT91_PIN_PB7, 0);     /* LCDD2 */
 169         at91_set_A_periph(AT91_PIN_PB8, 0);     /* LCDD3 */
 170         at91_set_A_periph(AT91_PIN_PB9, 0);     /* LCDD4 */
 171         at91_set_A_periph(AT91_PIN_PB10, 0);    /* LCDD5 */
 172         at91_set_A_periph(AT91_PIN_PB11, 0);    /* LCDD6 */
 173         at91_set_A_periph(AT91_PIN_PB12, 0);    /* LCDD7 */
 174         at91_set_A_periph(AT91_PIN_PB15, 0);    /* LCDD10 */
 175         at91_set_A_periph(AT91_PIN_PB16, 0);    /* LCDD11 */
 176         at91_set_A_periph(AT91_PIN_PB17, 0);    /* LCDD12 */
 177         at91_set_A_periph(AT91_PIN_PB18, 0);    /* LCDD13 */
 178         at91_set_A_periph(AT91_PIN_PB19, 0);    /* LCDD14 */
 179         at91_set_A_periph(AT91_PIN_PB20, 0);    /* LCDD15 */
 180         at91_set_B_periph(AT91_PIN_PB23, 0);    /* LCDD18 */
 181         at91_set_B_periph(AT91_PIN_PB24, 0);    /* LCDD19 */
 182         at91_set_B_periph(AT91_PIN_PB25, 0);    /* LCDD20 */
 183         at91_set_B_periph(AT91_PIN_PB26, 0);    /* LCDD21 */
 184         at91_set_B_periph(AT91_PIN_PB27, 0);    /* LCDD22 */
 185         at91_set_B_periph(AT91_PIN_PB28, 0);    /* LCDD23 */
 186
 187         at91_system_clk_enable(AT91_PMC_HCK1);
 188
 189         /* For 9G10EK, let U-Boot allocate the framebuffer in SDRAM */
 190 #ifdef CONFIG_AT91SAM9261EK
 191         gd->fb_base = ATMEL_BASE_SRAM;
 192 #endif
 193 }
 194
 195 #ifdef CONFIG_LCD_INFO
 196 #include <nand.h>
 197 #include <version.h>
 198
 199 void lcd_show_board_info(void)
 200 {
 201         ulong dram_size, nand_size;
 202         int i;
 203         char temp[32];
 204
 205         lcd_printf ("%s\n", U_BOOT_VERSION);
 206         lcd_printf ("(C) 2008 ATMEL Corp\n");
 207         lcd_printf ("at91support@atmel.com\n");
 208         lcd_printf ("%s CPU at %s MHz\n",
 209                 ATMEL_CPU_NAME,
 210                 strmhz(temp, get_cpu_clk_rate()));
 211
 212         dram_size = 0;
 213         for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++)
 214                 dram_size += gd->bd->bi_dram[i].size;
 215         nand_size = 0;
 216         for (i = 0; i < CONFIG_SYS_MAX_NAND_DEVICE; i++)
 217                 nand_size += get_nand_dev_by_index(i)->size;
 218         lcd_printf ("  %ld MB SDRAM, %ld MB NAND\n",
 219                 dram_size >> 20,
 220                 nand_size >> 20 );
 221 }
 222 #endif /* CONFIG_LCD_INFO */
 223 #endif
 224
 225 #ifdef CONFIG_DEBUG_UART_BOARD_INIT
 226 void board_debug_uart_init(void)
 227 {
 228         at91_seriald_hw_init();
 229 }
 230 #endif
 231
 232 #ifdef CONFIG_BOARD_EARLY_INIT_F
 233 int board_early_init_f(void)
 234 {
 235 #ifdef CONFIG_DEBUG_UART
 236         debug_uart_init();
 237 #endif
 238         return 0;
 239 }
 240 #endif
 241
 242 int board_init(void)
 243 {
 244 #ifdef CONFIG_AT91SAM9G10EK
 245         /* arch number of AT91SAM9G10EK-Board */
 246         gd->bd->bi_arch_number = MACH_TYPE_AT91SAM9G10EK;
 247 #else
 248         /* arch number of AT91SAM9261EK-Board */
 249         gd->bd->bi_arch_number = MACH_TYPE_AT91SAM9261EK;
 250 #endif
 251         /* adress of boot parameters */
 252         gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
 253
 254 #ifdef CONFIG_CMD_NAND
 255         at91sam9261ek_nand_hw_init();
 256 #endif
 257 #ifdef CONFIG_DRIVER_DM9000
 258         at91sam9261ek_dm9000_hw_init();
 259 #endif
 260 #ifdef CONFIG_LCD
 261         at91sam9261ek_lcd_hw_init();
 262 #endif
 263         return 0;
 264 }
 265
 266 #ifdef CONFIG_DRIVER_DM9000
 267 int board_eth_init(bd_t *bis)
 268 {
 269         return dm9000_initialize(bis);
 270 }
 271 #endif
 272
 273 int dram_init(void)
 274 {
 275         gd->ram_size = get_ram_size((void *)CONFIG_SYS_SDRAM_BASE,
 276                 CONFIG_SYS_SDRAM_SIZE);
 277
 278         return 0;
 279 }
 280
 281 #ifdef CONFIG_RESET_PHY_R
 282 void reset_phy(void)
 283 {
 284 #ifdef CONFIG_DRIVER_DM9000
 285         /*
 286          * Initialize ethernet HW addr prior to starting Linux,
 287          * needed for nfsroot
 288          */
 289         eth_init();
 290 #endif
 291 }
 292 #endif