3 The BSC9132 is a highly integrated device that targets the evolving
4 Microcell, Picocell, and Enterprise-Femto base station market subsegments.
6 The BSC9132 device combines Power Architecture e500 and DSP StarCore SC3850
7 core technologies with MAPLE-B2P baseband acceleration processing elements
8 to address the need for a high performance, low cost, integrated solution
9 that handles all required processing layers without the need for an
10 external device except for an RF transceiver or, in a Micro base station
11 configuration, a host device that handles the L3/L4 and handover between
14 The BSC9132 SoC includes the following function and features:
15 - Power Architecture subsystem including two e500 processors with
16 512-Kbyte shared L2 cache
17 - Two StarCore SC3850 DSP subsystems, each with a 512-Kbyte private L2
19 - 32 Kbyte of shared M3 memory
20 - The Multi Accelerator Platform Engine for Pico BaseStation Baseband
21 Processing (MAPLE-B2P)
22 - Two DDR3/3L memory interfaces with 32-bit data width (40 bits including
23 ECC), up to 1333 MHz data rate
24 - Dedicated security engine featuring trusted boot
26 - OCNDMA with four bidirectional channels
27 - SysDMA with sixteen bidirectional channels
29 - Four-lane SerDes PHY
30 - PCI Express controller complies with the PEX Specification-Rev 2.0
31 - Two Common Public Radio Interface (CPRI) controller lanes
32 - High-speed USB 2.0 host and device controller with ULPI interface
33 - Enhanced secure digital (SD/MMC) host controller (eSDHC)
34 - Antenna interface controller (AIC), supporting four industry
35 standard JESD207/four custom ADI RF interfaces
36 - ADI lanes support both full duplex FDD support & half duplex TDD
37 - Universal Subscriber Identity Module (USIM) interface that
38 facilitates communication to SIM cards or Eurochip pre-paid phone
40 - Two DUART, two eSPI, and two I2C controllers
41 - Integrated Flash memory controller (IFC)
43 - Sixteen 32-bit timers
45 The SC3850 core subsystem consists of the following:
46 - 32 KB, 8-way, level 1 instruction cache (L1 ICache)
47 - 32 KB, 8-way, level 1 data cache (L1 DCache)
48 - 512 KB, 8-way, level 2 unified instruction/data cache (L2 cache/M2 memory)
49 - Memory management unit (MMU)
50 - Global interrupt controller ( GIC)
51 - Debug and profiling unit (DPU)
52 - Two 32-bit quad timers
54 BSC9132QDS board Overview
55 -------------------------
56 2Gbyte DDR3 (on board DDR), Dual Ranki
57 32Mbyte 16bit NOR flash
58 128Mbyte 2K page size NAND Flash
59 256 Kbit M24256 I2C EEPROM
60 128 Mbit SPI Flash memory
63 eTSEC1: Connected to SGMII PHY
64 eTSEC2: Connected to SGMII PHY
69 DUART interface: supports one UARTs up to 115200 bps for console display
71 Frequency Combinations Supported
72 --------------------------------
73 Core MHz/CCB MHz/DDR(MT/s)
74 1. CPU0/CPU1/CCB/DDR: 1000MHz/1000MHz/500MHz/800MHz
75 (SYSCLK = 100MHz, DDRCLK = 100MHz)
76 2. CPU0/CPU1/CCB/DDR: 1200MHz/1200MHz/600MHz/1330MHz
77 (SYSCLK = 100MHz, DDRCLK = 133MHz)
79 Boot Methods Supported
80 -----------------------
92 To build the U-Boot for BSC9132QDS:
94 make BSC9132QDS_NOR_DDRCLK100 : For 100MHZ DDR CLK
95 make BSC9132QDS_NOR_DDRCLK133 : For 133MHZ DDR CLK
96 2. NAND Flash : It is currently not supported
98 make BSC9132QDS_SPIFLASH_DDRCLK100 : For 100MHZ DDR CLK
99 make BSC9132QDS_SPIFLASH_DDRCLK133 : For 133MHZ DDR CLK
101 make BSC9132QDS_SDCARD_DDRCLK100 : For 100MHZ DDR CLK
102 make BSC9132QDS_SDCARD_DDRCLK133 : For 133MHZ DDR CLK
106 0x0000_0000 0x7FFF_FFFF DDR 2G cacheable
107 0x8000_0000 0x8FFF_FFFF NOR Flash 256M
108 0x9000_0000 0x9FFF_FFFF PCIe Memory 256M
109 0xA000_0000 0xA7FF_FFFF DSP core1 L2 space 128M
110 0xB000_0000 0xB0FF_FFFF DSP core0 M2 space 16M
111 0xB100_0000 0xB1FF_FFFF DSP core1 M2 space 16M
112 0xC000_0000 0xC000_7FFF M3 Memory 32K
113 0xC001_0000 0xC001_FFFF PCI Express I/O 64K
114 0xC100_0000 0xC13F_FFFF MAPLE-2F 4M
115 0xC1F0_0000 0xC1F7_FFFF PA SRAM Region 0 512K
116 0xC1F8_0000 0xC1FB_FFFF PA SRAM Region 1 512K
117 0xFED0_0000 0xFED0_3FFF SEC Secured RAM 16K
118 0xFEE0_0000 0xFEE0_0FFF DSP Boot ROM 4K
119 0xFF60_0000 0xFF6F_FFFF DSP CCSR 1M
120 0xFF70_0000 0xFF7F_FFFF PA CCSR 1M
121 0xFF80_0000 0xFFFF_FFFF Boot Page & NAND Buffer 8M
125 To place a new U-Boot image in the NAND flash and then boot
126 with that new image temporarily, use this:
127 tftp 1000000 u-boot-nand.bin
129 nand write 1000000 0 100000
132 Using the Device Tree Source File
133 ---------------------------------
134 To create the DTB (Device Tree Binary) image file,
135 use a command similar to this:
137 dtc -b 0 -f -I dts -O dtb bsc9132qds.dts > bsc9132qds.dtb
139 Likely, that .dts file will come from here;
141 linux-2.6/arch/powerpc/boot/dts/bsc9132qds.dts
145 Place a linux uImage in the TFTP disk area.
148 tftp 2000000 rootfs.ext2.gz.uboot
149 tftp c00000 bsc9132qds.dtb
150 bootm 1000000 2000000 c00000