git.sur5r.net Git - u-boot/blob - board/freescale/ls2080ardb/ddr.c

   1 /*
   2  * Copyright 2015 Freescale Semiconductor, Inc.
   3  *
   4  * SPDX-License-Identifier:     GPL-2.0+
   5  */
   6
   7 #include <common.h>
   8 #include <fsl_ddr_sdram.h>
   9 #include <fsl_ddr_dimm_params.h>
  10 #include <asm/arch/soc.h>
  11 #include "ddr.h"
  12
  13 DECLARE_GLOBAL_DATA_PTR;
  14
  15 void fsl_ddr_board_options(memctl_options_t *popts,
  16                                 dimm_params_t *pdimm,
  17                                 unsigned int ctrl_num)
  18 {
  19 #ifdef CONFIG_SYS_FSL_HAS_DP_DDR
  20         u8 dq_mapping_0, dq_mapping_2, dq_mapping_3;
  21 #endif
  22         const struct board_specific_parameters *pbsp, *pbsp_highest = NULL;
  23         ulong ddr_freq;
  24         int slot;
  25
  26         if (ctrl_num > 2) {
  27                 printf("Not supported controller number %d\n", ctrl_num);
  28                 return;
  29         }
  30
  31         for (slot = 0; slot < CONFIG_DIMM_SLOTS_PER_CTLR; slot++) {
  32                 if (pdimm[slot].n_ranks)
  33                         break;
  34         }
  35
  36         if (slot >= CONFIG_DIMM_SLOTS_PER_CTLR)
  37                 return;
  38
  39         /*
  40          * we use identical timing for all slots. If needed, change the code
  41          * to  pbsp = rdimms[ctrl_num] or pbsp = udimms[ctrl_num];
  42          */
  43         if (popts->registered_dimm_en)
  44                 pbsp = rdimms[ctrl_num];
  45         else
  46                 pbsp = udimms[ctrl_num];
  47
  48
  49         /* Get clk_adjust, wrlvl_start, wrlvl_ctl, according to the board ddr
  50          * freqency and n_banks specified in board_specific_parameters table.
  51          */
  52         ddr_freq = get_ddr_freq(ctrl_num) / 1000000;
  53         while (pbsp->datarate_mhz_high) {
  54                 if (pbsp->n_ranks == pdimm[slot].n_ranks &&
  55                     (pdimm[slot].rank_density >> 30) >= pbsp->rank_gb) {
  56                         if (ddr_freq <= pbsp->datarate_mhz_high) {
  57                                 popts->clk_adjust = pbsp->clk_adjust;
  58                                 popts->wrlvl_start = pbsp->wrlvl_start;
  59                                 popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2;
  60                                 popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3;
  61                                 goto found;
  62                         }
  63                         pbsp_highest = pbsp;
  64                 }
  65                 pbsp++;
  66         }
  67
  68         if (pbsp_highest) {
  69                 printf("Error: board specific timing not found for data rate %lu MT/s\n"
  70                         "Trying to use the highest speed (%u) parameters\n",
  71                         ddr_freq, pbsp_highest->datarate_mhz_high);
  72                 popts->clk_adjust = pbsp_highest->clk_adjust;
  73                 popts->wrlvl_start = pbsp_highest->wrlvl_start;
  74                 popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2;
  75                 popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3;
  76         } else {
  77                 panic("DIMM is not supported by this board");
  78         }
  79 found:
  80         debug("Found timing match: n_ranks %d, data rate %d, rank_gb %d\n"
  81                 "\tclk_adjust %d, wrlvl_start %d, wrlvl_ctrl_2 0x%x, wrlvl_ctrl_3 0x%x\n",
  82                 pbsp->n_ranks, pbsp->datarate_mhz_high, pbsp->rank_gb,
  83                 pbsp->clk_adjust, pbsp->wrlvl_start, pbsp->wrlvl_ctl_2,
  84                 pbsp->wrlvl_ctl_3);
  85 #ifdef CONFIG_SYS_FSL_HAS_DP_DDR
  86         if (ctrl_num == CONFIG_DP_DDR_CTRL) {
  87                 /* force DDR bus width to 32 bits */
  88                 popts->data_bus_width = 1;
  89                 popts->otf_burst_chop_en = 0;
  90                 popts->burst_length = DDR_BL8;
  91                 popts->bstopre = 0;     /* enable auto precharge */
  92                 /*
  93                  * Layout optimization results byte mapping
  94                  * Byte 0 -> Byte ECC
  95                  * Byte 1 -> Byte 3
  96                  * Byte 2 -> Byte 2
  97                  * Byte 3 -> Byte 1
  98                  * Byte ECC -> Byte 0
  99                  */
 100                 dq_mapping_0 = pdimm[slot].dq_mapping[0];
 101                 dq_mapping_2 = pdimm[slot].dq_mapping[2];
 102                 dq_mapping_3 = pdimm[slot].dq_mapping[3];
 103                 pdimm[slot].dq_mapping[0] = pdimm[slot].dq_mapping[8];
 104                 pdimm[slot].dq_mapping[1] = pdimm[slot].dq_mapping[9];
 105                 pdimm[slot].dq_mapping[2] = pdimm[slot].dq_mapping[6];
 106                 pdimm[slot].dq_mapping[3] = pdimm[slot].dq_mapping[7];
 107                 pdimm[slot].dq_mapping[6] = dq_mapping_2;
 108                 pdimm[slot].dq_mapping[7] = dq_mapping_3;
 109                 pdimm[slot].dq_mapping[8] = dq_mapping_0;
 110                 pdimm[slot].dq_mapping[9] = 0;
 111                 pdimm[slot].dq_mapping[10] = 0;
 112                 pdimm[slot].dq_mapping[11] = 0;
 113                 pdimm[slot].dq_mapping[12] = 0;
 114                 pdimm[slot].dq_mapping[13] = 0;
 115                 pdimm[slot].dq_mapping[14] = 0;
 116                 pdimm[slot].dq_mapping[15] = 0;
 117                 pdimm[slot].dq_mapping[16] = 0;
 118                 pdimm[slot].dq_mapping[17] = 0;
 119         }
 120 #endif
 121         /* To work at higher than 1333MT/s */
 122         popts->half_strength_driver_enable = 0;
 123         /*
 124          * Write leveling override
 125          */
 126         popts->wrlvl_override = 1;
 127         popts->wrlvl_sample = 0x0;      /* 32 clocks */
 128
 129         /*
 130          * Rtt and Rtt_WR override
 131          */
 132         popts->rtt_override = 0;
 133
 134         /* Enable ZQ calibration */
 135         popts->zq_en = 1;
 136
 137         if (ddr_freq < 2350) {
 138                 if (pdimm[0].n_ranks == 2 && pdimm[1].n_ranks == 2) {
 139                         /* four chip-selects */
 140                         popts->ddr_cdr1 = DDR_CDR1_DHC_EN |
 141                                           DDR_CDR1_ODT(DDR_CDR_ODT_80ohm);
 142                         popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_80ohm);
 143                         popts->twot_en = 1;     /* enable 2T timing */
 144                 } else {
 145                         popts->ddr_cdr1 = DDR_CDR1_DHC_EN |
 146                                           DDR_CDR1_ODT(DDR_CDR_ODT_60ohm);
 147                         popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_60ohm) |
 148                                           DDR_CDR2_VREF_RANGE_2;
 149                 }
 150         } else {
 151                 popts->ddr_cdr1 = DDR_CDR1_DHC_EN |
 152                                   DDR_CDR1_ODT(DDR_CDR_ODT_100ohm);
 153                 popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_100ohm) |
 154                                   DDR_CDR2_VREF_RANGE_2;
 155         }
 156 }
 157
 158 phys_size_t initdram(int board_type)
 159 {
 160         phys_size_t dram_size;
 161
 162 #if defined(CONFIG_SPL) && !defined(CONFIG_SPL_BUILD)
 163         return fsl_ddr_sdram_size();
 164 #else
 165         puts("Initializing DDR....using SPD\n");
 166
 167         dram_size = fsl_ddr_sdram();
 168 #endif
 169
 170         return dram_size;
 171 }
 172
 173 void dram_init_banksize(void)
 174 {
 175 #ifdef CONFIG_SYS_DP_DDR_BASE_PHY
 176         phys_size_t dp_ddr_size;
 177 #endif
 178
 179         /*
 180          * gd->arch.secure_ram tracks the location of secure memory.
 181          * It was set as if the memory starts from 0.
 182          * The address needs to add the offset of its bank.
 183          */
 184         gd->bd->bi_dram[0].start = CONFIG_SYS_SDRAM_BASE;
 185         if (gd->ram_size > CONFIG_SYS_LS2_DDR_BLOCK1_SIZE) {
 186                 gd->bd->bi_dram[0].size = CONFIG_SYS_LS2_DDR_BLOCK1_SIZE;
 187                 gd->bd->bi_dram[1].start = CONFIG_SYS_DDR_BLOCK2_BASE;
 188                 gd->bd->bi_dram[1].size = gd->ram_size -
 189                                           CONFIG_SYS_LS2_DDR_BLOCK1_SIZE;
 190 #ifdef CONFIG_SYS_MEM_RESERVE_SECURE
 191                 gd->arch.secure_ram = gd->bd->bi_dram[1].start +
 192                                       gd->arch.secure_ram -
 193                                       CONFIG_SYS_LS2_DDR_BLOCK1_SIZE;
 194                 gd->arch.secure_ram |= MEM_RESERVE_SECURE_MAINTAINED;
 195 #endif
 196         } else {
 197                 gd->bd->bi_dram[0].size = gd->ram_size;
 198 #ifdef CONFIG_SYS_MEM_RESERVE_SECURE
 199                 gd->arch.secure_ram = gd->bd->bi_dram[0].start +
 200                                       gd->arch.secure_ram;
 201                 gd->arch.secure_ram |= MEM_RESERVE_SECURE_MAINTAINED;
 202 #endif
 203         }
 204
 205 #ifdef CONFIG_SYS_DP_DDR_BASE_PHY
 206         if (soc_has_dp_ddr()) {
 207                 /* initialize DP-DDR here */
 208                 puts("DP-DDR:  ");
 209                 /*
 210                  * DDR controller use 0 as the base address for binding.
 211                  * It is mapped to CONFIG_SYS_DP_DDR_BASE for core to access.
 212                  */
 213                 dp_ddr_size = fsl_other_ddr_sdram(CONFIG_SYS_DP_DDR_BASE_PHY,
 214                                           CONFIG_DP_DDR_CTRL,
 215                                           CONFIG_DP_DDR_NUM_CTRLS,
 216                                           CONFIG_DP_DDR_DIMM_SLOTS_PER_CTLR,
 217                                           NULL, NULL, NULL);
 218                 if (dp_ddr_size) {
 219                         gd->bd->bi_dram[2].start = CONFIG_SYS_DP_DDR_BASE;
 220                         gd->bd->bi_dram[2].size = dp_ddr_size;
 221                 } else {
 222                         puts("Not detected");
 223                 }
 224         }
 225 #endif
 226 }