git.sur5r.net Git - u-boot/blob - board/freescale/mx6sxsabreauto/mx6sxsabreauto.c

   1 /*
   2  * Copyright (C) 2014 Freescale Semiconductor, Inc.
   3  *
   4  * Author: Ye Li <ye.li@nxp.com>
   5  *
   6  * SPDX-License-Identifier:     GPL-2.0+
   7  */
   8
   9 #include <asm/arch/clock.h>
  10 #include <asm/arch/crm_regs.h>
  11 #include <asm/arch/iomux.h>
  12 #include <asm/arch/imx-regs.h>
  13 #include <asm/arch/mx6-pins.h>
  14 #include <asm/arch/sys_proto.h>
  15 #include <asm/gpio.h>
  16 #include <asm/imx-common/iomux-v3.h>
  17 #include <asm/imx-common/boot_mode.h>
  18 #include <asm/io.h>
  19 #include <asm/imx-common/mxc_i2c.h>
  20 #include <linux/sizes.h>
  21 #include <common.h>
  22 #include <fsl_esdhc.h>
  23 #include <mmc.h>
  24 #include <i2c.h>
  25 #include <miiphy.h>
  26 #include <netdev.h>
  27 #include <power/pmic.h>
  28 #include <power/pfuze100_pmic.h>
  29 #include "../common/pfuze.h"
  30 #include <usb.h>
  31 #include <usb/ehci-ci.h>
  32 #include <pca953x.h>
  33
  34 DECLARE_GLOBAL_DATA_PTR;
  35
  36 #define UART_PAD_CTRL  (PAD_CTL_PKE | PAD_CTL_PUE |             \
  37         PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED |               \
  38         PAD_CTL_DSE_40ohm   | PAD_CTL_SRE_FAST  | PAD_CTL_HYS)
  39
  40 #define USDHC_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE |             \
  41         PAD_CTL_PUS_22K_UP  | PAD_CTL_SPEED_LOW |               \
  42         PAD_CTL_DSE_80ohm   | PAD_CTL_SRE_FAST  | PAD_CTL_HYS)
  43
  44 #define I2C_PAD_CTRL    (PAD_CTL_PKE | PAD_CTL_PUE |            \
  45         PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED |               \
  46         PAD_CTL_DSE_40ohm | PAD_CTL_HYS |                       \
  47         PAD_CTL_ODE)
  48
  49 #define ENET_PAD_CTRL  (PAD_CTL_PUS_100K_UP | PAD_CTL_PUE |     \
  50         PAD_CTL_SPEED_HIGH   |                                   \
  51         PAD_CTL_DSE_48ohm   | PAD_CTL_SRE_FAST)
  52
  53 #define ENET_CLK_PAD_CTRL  (PAD_CTL_SPEED_MED | \
  54         PAD_CTL_DSE_120ohm   | PAD_CTL_SRE_FAST)
  55
  56 #define ENET_RX_PAD_CTRL  (PAD_CTL_PKE | PAD_CTL_PUE |          \
  57         PAD_CTL_SPEED_HIGH   | PAD_CTL_SRE_FAST)
  58
  59 #define I2C_PMIC        1
  60
  61 #define GPMI_PAD_CTRL0 (PAD_CTL_PKE | PAD_CTL_PUE | PAD_CTL_PUS_100K_UP)
  62 #define GPMI_PAD_CTRL1 (PAD_CTL_DSE_40ohm | PAD_CTL_SPEED_MED | \
  63                         PAD_CTL_SRE_FAST)
  64 #define GPMI_PAD_CTRL2 (GPMI_PAD_CTRL0 | GPMI_PAD_CTRL1)
  65
  66 /*Define for building port exp gpio, pin starts from 0*/
  67 #define PORTEXP_IO_NR(chip, pin) \
  68         ((chip << 5) + pin)
  69
  70 /*Get the chip addr from a ioexp gpio*/
  71 #define PORTEXP_IO_TO_CHIP(gpio_nr) \
  72         (gpio_nr >> 5)
  73
  74 /*Get the pin number from a ioexp gpio*/
  75 #define PORTEXP_IO_TO_PIN(gpio_nr) \
  76         (gpio_nr & 0x1f)
  77
  78 #define CPU_PER_RST_B   PORTEXP_IO_NR(0x30, 4)
  79 #define STEER_ENET              PORTEXP_IO_NR(0x32, 2)
  80
  81 static int port_exp_direction_output(unsigned gpio, int value)
  82 {
  83         int ret;
  84
  85         i2c_set_bus_num(2);
  86         ret = i2c_probe(PORTEXP_IO_TO_CHIP(gpio));
  87         if (ret)
  88                 return ret;
  89
  90         ret = pca953x_set_dir(PORTEXP_IO_TO_CHIP(gpio),
  91                 (1 << PORTEXP_IO_TO_PIN(gpio)),
  92                 (PCA953X_DIR_OUT << PORTEXP_IO_TO_PIN(gpio)));
  93
  94         if (ret)
  95                 return ret;
  96
  97         ret = pca953x_set_val(PORTEXP_IO_TO_CHIP(gpio),
  98                 (1 << PORTEXP_IO_TO_PIN(gpio)),
  99                 (value << PORTEXP_IO_TO_PIN(gpio)));
 100
 101         if (ret)
 102                 return ret;
 103
 104         return 0;
 105 }
 106
 107 int dram_init(void)
 108 {
 109         gd->ram_size = PHYS_SDRAM_SIZE;
 110
 111         return 0;
 112 }
 113
 114 static iomux_v3_cfg_t const uart1_pads[] = {
 115         MX6_PAD_GPIO1_IO04__UART1_TX | MUX_PAD_CTRL(UART_PAD_CTRL),
 116         MX6_PAD_GPIO1_IO05__UART1_RX | MUX_PAD_CTRL(UART_PAD_CTRL),
 117 };
 118
 119 static iomux_v3_cfg_t const usdhc3_pads[] = {
 120         MX6_PAD_SD3_CLK__USDHC3_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
 121         MX6_PAD_SD3_CMD__USDHC3_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
 122         MX6_PAD_SD3_DATA0__USDHC3_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
 123         MX6_PAD_SD3_DATA1__USDHC3_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
 124         MX6_PAD_SD3_DATA2__USDHC3_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
 125         MX6_PAD_SD3_DATA3__USDHC3_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
 126         MX6_PAD_SD3_DATA4__USDHC3_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
 127         MX6_PAD_SD3_DATA5__USDHC3_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
 128         MX6_PAD_SD3_DATA6__USDHC3_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
 129         MX6_PAD_SD3_DATA7__USDHC3_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
 130
 131         /* CD pin */
 132         MX6_PAD_USB_H_DATA__GPIO7_IO_10 | MUX_PAD_CTRL(NO_PAD_CTRL),
 133
 134         /* RST_B, used for power reset cycle */
 135         MX6_PAD_KEY_COL1__GPIO2_IO_11 | MUX_PAD_CTRL(NO_PAD_CTRL),
 136 };
 137
 138 static iomux_v3_cfg_t const usdhc4_pads[] = {
 139         MX6_PAD_SD4_CLK__USDHC4_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
 140         MX6_PAD_SD4_CMD__USDHC4_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
 141         MX6_PAD_SD4_DATA0__USDHC4_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
 142         MX6_PAD_SD4_DATA1__USDHC4_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
 143         MX6_PAD_SD4_DATA2__USDHC4_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
 144         MX6_PAD_SD4_DATA3__USDHC4_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
 145         MX6_PAD_SD4_DATA4__USDHC4_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
 146         MX6_PAD_SD4_DATA5__USDHC4_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
 147         MX6_PAD_SD4_DATA6__USDHC4_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
 148         MX6_PAD_SD4_DATA7__USDHC4_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
 149
 150         /* CD pin */
 151         MX6_PAD_USB_H_STROBE__GPIO7_IO_11 | MUX_PAD_CTRL(NO_PAD_CTRL),
 152 };
 153
 154 static iomux_v3_cfg_t const fec2_pads[] = {
 155         MX6_PAD_ENET1_MDC__ENET2_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL),
 156         MX6_PAD_ENET1_MDIO__ENET2_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL),
 157         MX6_PAD_RGMII2_RX_CTL__ENET2_RX_EN | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
 158         MX6_PAD_RGMII2_RD0__ENET2_RX_DATA_0 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
 159         MX6_PAD_RGMII2_RD1__ENET2_RX_DATA_1 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
 160         MX6_PAD_RGMII2_RD2__ENET2_RX_DATA_2 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
 161         MX6_PAD_RGMII2_RD3__ENET2_RX_DATA_3 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
 162         MX6_PAD_RGMII2_RXC__ENET2_RX_CLK | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
 163         MX6_PAD_RGMII2_TX_CTL__ENET2_TX_EN | MUX_PAD_CTRL(ENET_PAD_CTRL),
 164         MX6_PAD_RGMII2_TD0__ENET2_TX_DATA_0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
 165         MX6_PAD_RGMII2_TD1__ENET2_TX_DATA_1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
 166         MX6_PAD_RGMII2_TD2__ENET2_TX_DATA_2 | MUX_PAD_CTRL(ENET_PAD_CTRL),
 167         MX6_PAD_RGMII2_TD3__ENET2_TX_DATA_3 | MUX_PAD_CTRL(ENET_PAD_CTRL),
 168         MX6_PAD_RGMII2_TXC__ENET2_RGMII_TXC | MUX_PAD_CTRL(ENET_PAD_CTRL),
 169 };
 170
 171 static void setup_iomux_uart(void)
 172 {
 173         imx_iomux_v3_setup_multiple_pads(uart1_pads, ARRAY_SIZE(uart1_pads));
 174 }
 175
 176 static int setup_fec(void)
 177 {
 178         struct iomuxc *iomuxc_regs = (struct iomuxc *)IOMUXC_BASE_ADDR;
 179
 180         /* Use 125MHz anatop loopback REF_CLK1 for ENET2 */
 181         clrsetbits_le32(&iomuxc_regs->gpr[1], IOMUX_GPR1_FEC2_MASK, 0);
 182
 183         return enable_fec_anatop_clock(1, ENET_125MHZ);
 184 }
 185
 186 int board_eth_init(bd_t *bis)
 187 {
 188         int ret;
 189
 190         imx_iomux_v3_setup_multiple_pads(fec2_pads, ARRAY_SIZE(fec2_pads));
 191         setup_fec();
 192
 193         ret = fecmxc_initialize_multi(bis, 1,
 194                 CONFIG_FEC_MXC_PHYADDR, IMX_FEC_BASE);
 195         if (ret)
 196                 printf("FEC%d MXC: %s:failed\n", 1, __func__);
 197
 198         return ret;
 199 }
 200
 201 int board_phy_config(struct phy_device *phydev)
 202 {
 203         /*
 204          * Enable 1.8V(SEL_1P5_1P8_POS_REG) on
 205          * Phy control debug reg 0
 206          */
 207         phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x1f);
 208         phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x8);
 209
 210         /* rgmii tx clock delay enable */
 211         phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x05);
 212         phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x100);
 213
 214         if (phydev->drv->config)
 215                 phydev->drv->config(phydev);
 216
 217         return 0;
 218 }
 219
 220 #define PC MUX_PAD_CTRL(I2C_PAD_CTRL)
 221 /* I2C2 for PMIC */
 222 struct i2c_pads_info i2c_pad_info2 = {
 223         .scl = {
 224                 .i2c_mode = MX6_PAD_GPIO1_IO02__I2C2_SCL | PC,
 225                 .gpio_mode = MX6_PAD_GPIO1_IO02__GPIO1_IO_2 | PC,
 226                 .gp = IMX_GPIO_NR(1, 2),
 227         },
 228         .sda = {
 229                 .i2c_mode = MX6_PAD_GPIO1_IO03__I2C2_SDA | PC,
 230                 .gpio_mode = MX6_PAD_GPIO1_IO03__GPIO1_IO_3 | PC,
 231                 .gp = IMX_GPIO_NR(1, 3),
 232         },
 233 };
 234
 235 /* I2C3 for IO Expander */
 236 struct i2c_pads_info i2c_pad_info3 = {
 237         .scl = {
 238                 .i2c_mode = MX6_PAD_KEY_COL4__I2C3_SCL | PC,
 239                 .gpio_mode = MX6_PAD_KEY_COL4__GPIO2_IO_14 | PC,
 240                 .gp = IMX_GPIO_NR(2, 14),
 241         },
 242         .sda = {
 243                 .i2c_mode = MX6_PAD_KEY_ROW4__I2C3_SDA | PC,
 244                 .gpio_mode = MX6_PAD_KEY_ROW4__GPIO2_IO_19 | PC,
 245                 .gp = IMX_GPIO_NR(2, 19),
 246         },
 247 };
 248
 249 int power_init_board(void)
 250 {
 251         struct pmic *p;
 252
 253         p = pfuze_common_init(I2C_PMIC);
 254         if (!p)
 255                 return -ENODEV;
 256
 257         return 0;
 258 }
 259
 260 #ifdef CONFIG_USB_EHCI_MX6
 261 #define USB_OTHERREGS_OFFSET    0x800
 262 #define UCTRL_PWR_POL           (1 << 9)
 263
 264 static iomux_v3_cfg_t const usb_otg_pads[] = {
 265         /* OGT1 */
 266         MX6_PAD_GPIO1_IO09__USB_OTG1_PWR | MUX_PAD_CTRL(NO_PAD_CTRL),
 267         MX6_PAD_GPIO1_IO10__ANATOP_OTG1_ID | MUX_PAD_CTRL(NO_PAD_CTRL),
 268         /* OTG2 */
 269         MX6_PAD_GPIO1_IO12__USB_OTG2_PWR | MUX_PAD_CTRL(NO_PAD_CTRL)
 270 };
 271
 272 static void setup_usb(void)
 273 {
 274         imx_iomux_v3_setup_multiple_pads(usb_otg_pads,
 275                                          ARRAY_SIZE(usb_otg_pads));
 276 }
 277
 278 int board_usb_phy_mode(int port)
 279 {
 280         if (port == 1)
 281                 return USB_INIT_HOST;
 282         else
 283                 return usb_phy_mode(port);
 284 }
 285
 286 int board_ehci_hcd_init(int port)
 287 {
 288         u32 *usbnc_usb_ctrl;
 289
 290         if (port > 1)
 291                 return -EINVAL;
 292
 293         usbnc_usb_ctrl = (u32 *)(USB_BASE_ADDR + USB_OTHERREGS_OFFSET +
 294                                  port * 4);
 295
 296         /* Set Power polarity */
 297         setbits_le32(usbnc_usb_ctrl, UCTRL_PWR_POL);
 298
 299         return 0;
 300 }
 301 #endif
 302
 303 int board_early_init_f(void)
 304 {
 305         setup_iomux_uart();
 306
 307         return 0;
 308 }
 309
 310 static struct fsl_esdhc_cfg usdhc_cfg[3] = {
 311         {USDHC3_BASE_ADDR},
 312         {USDHC4_BASE_ADDR},
 313 };
 314
 315 #define USDHC3_CD_GPIO  IMX_GPIO_NR(7, 10)
 316 #define USDHC3_RST_GPIO IMX_GPIO_NR(2, 11)
 317 #define USDHC4_CD_GPIO  IMX_GPIO_NR(7, 11)
 318
 319 int board_mmc_getcd(struct mmc *mmc)
 320 {
 321         struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
 322         int ret = 0;
 323
 324         switch (cfg->esdhc_base) {
 325         case USDHC3_BASE_ADDR:
 326                 ret = !gpio_get_value(USDHC3_CD_GPIO);
 327                 break;
 328         case USDHC4_BASE_ADDR:
 329                 ret = !gpio_get_value(USDHC4_CD_GPIO);
 330                 break;
 331         }
 332
 333         return ret;
 334 }
 335
 336 int board_mmc_init(bd_t *bis)
 337 {
 338         int i, ret;
 339
 340         /*
 341          * According to the board_mmc_init() the following map is done:
 342          * (U-Boot device node)    (Physical Port)
 343          * mmc0                    USDHC3
 344          * mmc1                    USDHC4
 345          */
 346         for (i = 0; i < CONFIG_SYS_FSL_USDHC_NUM; i++) {
 347                 switch (i) {
 348                 case 0:
 349                         imx_iomux_v3_setup_multiple_pads(
 350                                 usdhc3_pads, ARRAY_SIZE(usdhc3_pads));
 351                         gpio_direction_input(USDHC3_CD_GPIO);
 352
 353                         /* This starts a power cycle for UHS-I. Need to set steer to B0 to A*/
 354                         gpio_direction_output(USDHC3_RST_GPIO, 0);
 355                         udelay(1000); /* need 1ms at least */
 356                         gpio_direction_output(USDHC3_RST_GPIO, 1);
 357
 358                         usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
 359                         break;
 360                 case 1:
 361                         imx_iomux_v3_setup_multiple_pads(
 362                                 usdhc4_pads, ARRAY_SIZE(usdhc4_pads));
 363                         gpio_direction_input(USDHC4_CD_GPIO);
 364                         usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC4_CLK);
 365                         break;
 366                 default:
 367                         printf("Warning: you configured more USDHC controllers"
 368                                 "(%d) than supported by the board\n", i + 1);
 369                         return -EINVAL;
 370                         }
 371
 372                         ret = fsl_esdhc_initialize(bis, &usdhc_cfg[i]);
 373                         if (ret) {
 374                                 printf("Warning: failed to initialize mmc dev %d\n", i);
 375                                 return ret;
 376                         }
 377         }
 378
 379         return 0;
 380 }
 381
 382 #ifdef CONFIG_FSL_QSPI
 383
 384 #define QSPI_PAD_CTRL1  \
 385         (PAD_CTL_SRE_FAST | PAD_CTL_SPEED_HIGH | \
 386          PAD_CTL_PKE | PAD_CTL_PUE | PAD_CTL_PUS_47K_UP | PAD_CTL_DSE_40ohm)
 387
 388 static iomux_v3_cfg_t const quadspi_pads[] = {
 389         MX6_PAD_QSPI1A_SS0_B__QSPI1_A_SS0_B   | MUX_PAD_CTRL(QSPI_PAD_CTRL1),
 390         MX6_PAD_QSPI1A_SCLK__QSPI1_A_SCLK     | MUX_PAD_CTRL(QSPI_PAD_CTRL1),
 391         MX6_PAD_QSPI1A_DATA0__QSPI1_A_DATA_0  | MUX_PAD_CTRL(QSPI_PAD_CTRL1),
 392         MX6_PAD_QSPI1A_DATA1__QSPI1_A_DATA_1  | MUX_PAD_CTRL(QSPI_PAD_CTRL1),
 393         MX6_PAD_QSPI1A_DATA2__QSPI1_A_DATA_2  | MUX_PAD_CTRL(QSPI_PAD_CTRL1),
 394         MX6_PAD_QSPI1A_DATA3__QSPI1_A_DATA_3  | MUX_PAD_CTRL(QSPI_PAD_CTRL1),
 395         MX6_PAD_QSPI1B_SS0_B__QSPI1_B_SS0_B   | MUX_PAD_CTRL(QSPI_PAD_CTRL1),
 396         MX6_PAD_QSPI1B_SCLK__QSPI1_B_SCLK     | MUX_PAD_CTRL(QSPI_PAD_CTRL1),
 397         MX6_PAD_QSPI1B_DATA0__QSPI1_B_DATA_0  | MUX_PAD_CTRL(QSPI_PAD_CTRL1),
 398         MX6_PAD_QSPI1B_DATA1__QSPI1_B_DATA_1  | MUX_PAD_CTRL(QSPI_PAD_CTRL1),
 399         MX6_PAD_QSPI1B_DATA2__QSPI1_B_DATA_2  | MUX_PAD_CTRL(QSPI_PAD_CTRL1),
 400         MX6_PAD_QSPI1B_DATA3__QSPI1_B_DATA_3  | MUX_PAD_CTRL(QSPI_PAD_CTRL1),
 401 };
 402
 403 int board_qspi_init(void)
 404 {
 405         /* Set the iomux */
 406         imx_iomux_v3_setup_multiple_pads(quadspi_pads,
 407                                          ARRAY_SIZE(quadspi_pads));
 408
 409         /* Set the clock */
 410         enable_qspi_clk(0);
 411
 412         return 0;
 413 }
 414 #endif
 415
 416 #ifdef CONFIG_NAND_MXS
 417 iomux_v3_cfg_t gpmi_pads[] = {
 418         MX6_PAD_NAND_CLE__RAWNAND_CLE           | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
 419         MX6_PAD_NAND_ALE__RAWNAND_ALE           | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
 420         MX6_PAD_NAND_WP_B__RAWNAND_WP_B | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
 421         MX6_PAD_NAND_READY_B__RAWNAND_READY_B   | MUX_PAD_CTRL(GPMI_PAD_CTRL0),
 422         MX6_PAD_NAND_CE0_B__RAWNAND_CE0_B               | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
 423         MX6_PAD_NAND_RE_B__RAWNAND_RE_B         | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
 424         MX6_PAD_NAND_WE_B__RAWNAND_WE_B         | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
 425         MX6_PAD_NAND_DATA00__RAWNAND_DATA00     | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
 426         MX6_PAD_NAND_DATA01__RAWNAND_DATA01     | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
 427         MX6_PAD_NAND_DATA02__RAWNAND_DATA02     | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
 428         MX6_PAD_NAND_DATA03__RAWNAND_DATA03     | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
 429         MX6_PAD_NAND_DATA04__RAWNAND_DATA04     | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
 430         MX6_PAD_NAND_DATA05__RAWNAND_DATA05     | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
 431         MX6_PAD_NAND_DATA06__RAWNAND_DATA06     | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
 432         MX6_PAD_NAND_DATA07__RAWNAND_DATA07     | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
 433 };
 434
 435 static void setup_gpmi_nand(void)
 436 {
 437         struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
 438
 439         /* config gpmi nand iomux */
 440         imx_iomux_v3_setup_multiple_pads(gpmi_pads, ARRAY_SIZE(gpmi_pads));
 441
 442         setup_gpmi_io_clk((MXC_CCM_CS2CDR_QSPI2_CLK_PODF(0) |
 443                         MXC_CCM_CS2CDR_QSPI2_CLK_PRED(3) |
 444                         MXC_CCM_CS2CDR_QSPI2_CLK_SEL(3)));
 445
 446         /* enable apbh clock gating */
 447         setbits_le32(&mxc_ccm->CCGR0, MXC_CCM_CCGR0_APBHDMA_MASK);
 448 }
 449 #endif
 450
 451 int board_init(void)
 452 {
 453         /* Address of boot parameters */
 454         gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
 455
 456 #ifdef CONFIG_SYS_I2C_MXC
 457         setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info2);
 458         setup_i2c(2, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info3);
 459 #endif
 460
 461         /* Reset CPU_PER_RST_B signal for enet phy and PCIE */
 462         port_exp_direction_output(CPU_PER_RST_B, 0);
 463         udelay(500);
 464         port_exp_direction_output(CPU_PER_RST_B, 1);
 465
 466         /* Set steering signal to L for selecting B0 */
 467         port_exp_direction_output(STEER_ENET, 0);
 468
 469 #ifdef CONFIG_USB_EHCI_MX6
 470         setup_usb();
 471 #endif
 472
 473 #ifdef CONFIG_FSL_QSPI
 474         board_qspi_init();
 475 #endif
 476
 477 #ifdef CONFIG_NAND_MXS
 478         setup_gpmi_nand();
 479 #endif
 480
 481         return 0;
 482 }
 483
 484 #ifdef CONFIG_CMD_BMODE
 485 static const struct boot_mode board_boot_modes[] = {
 486         {"sda", MAKE_CFGVAL(0x42, 0x30, 0x00, 0x00)},
 487         {"sdb", MAKE_CFGVAL(0x40, 0x38, 0x00, 0x00)},
 488         {"qspi1", MAKE_CFGVAL(0x10, 0x00, 0x00, 0x00)},
 489         {"nand", MAKE_CFGVAL(0x82, 0x00, 0x00, 0x00)},
 490         {NULL,   0},
 491 };
 492 #endif
 493
 494 int board_late_init(void)
 495 {
 496 #ifdef CONFIG_CMD_BMODE
 497         add_board_boot_modes(board_boot_modes);
 498 #endif
 499
 500         return 0;
 501 }
 502
 503 int checkboard(void)
 504 {
 505         puts("Board: MX6SX SABRE AUTO\n");
 506
 507         return 0;
 508 }