git.sur5r.net Git - u-boot/blob - board/freescale/mx6sxsabresd/mx6sxsabresd.c

   1 /*
   2  * Copyright (C) 2014 Freescale Semiconductor, Inc.
   3  *
   4  * Author: Fabio Estevam <fabio.estevam@freescale.com>
   5  *
   6  * SPDX-License-Identifier:     GPL-2.0+
   7  */
   8
   9 #include <asm/arch/clock.h>
  10 #include <asm/arch/crm_regs.h>
  11 #include <asm/arch/iomux.h>
  12 #include <asm/arch/imx-regs.h>
  13 #include <asm/arch/mx6-pins.h>
  14 #include <asm/arch/sys_proto.h>
  15 #include <asm/gpio.h>
  16 #include <asm/imx-common/iomux-v3.h>
  17 #include <asm/io.h>
  18 #include <asm/imx-common/mxc_i2c.h>
  19 #include <linux/sizes.h>
  20 #include <common.h>
  21 #include <fsl_esdhc.h>
  22 #include <mmc.h>
  23 #include <i2c.h>
  24 #include <miiphy.h>
  25 #include <netdev.h>
  26 #include <power/pmic.h>
  27 #include <power/pfuze100_pmic.h>
  28 #include "../common/pfuze.h"
  29 #include <usb.h>
  30 #include <usb/ehci-fsl.h>
  31
  32 DECLARE_GLOBAL_DATA_PTR;
  33
  34 #define UART_PAD_CTRL  (PAD_CTL_PKE | PAD_CTL_PUE |             \
  35         PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED |               \
  36         PAD_CTL_DSE_40ohm   | PAD_CTL_SRE_FAST  | PAD_CTL_HYS)
  37
  38 #define USDHC_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE |             \
  39         PAD_CTL_PUS_22K_UP  | PAD_CTL_SPEED_LOW |               \
  40         PAD_CTL_DSE_80ohm   | PAD_CTL_SRE_FAST  | PAD_CTL_HYS)
  41
  42 #define I2C_PAD_CTRL    (PAD_CTL_PKE | PAD_CTL_PUE |            \
  43         PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED |               \
  44         PAD_CTL_DSE_40ohm | PAD_CTL_HYS |                       \
  45         PAD_CTL_ODE)
  46
  47 #define ENET_PAD_CTRL  (PAD_CTL_PUS_100K_UP | PAD_CTL_PUE |     \
  48         PAD_CTL_SPEED_HIGH   |                                   \
  49         PAD_CTL_DSE_48ohm   | PAD_CTL_SRE_FAST)
  50
  51 #define ENET_CLK_PAD_CTRL  (PAD_CTL_SPEED_MED | \
  52         PAD_CTL_DSE_120ohm   | PAD_CTL_SRE_FAST)
  53
  54 #define ENET_RX_PAD_CTRL  (PAD_CTL_PKE | PAD_CTL_PUE |          \
  55         PAD_CTL_SPEED_HIGH   | PAD_CTL_SRE_FAST)
  56
  57 #define I2C_PAD_CTRL    (PAD_CTL_PKE | PAD_CTL_PUE |            \
  58         PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED |               \
  59         PAD_CTL_DSE_40ohm | PAD_CTL_HYS |                       \
  60         PAD_CTL_ODE)
  61
  62 int dram_init(void)
  63 {
  64         gd->ram_size = PHYS_SDRAM_SIZE;
  65
  66         return 0;
  67 }
  68
  69 static iomux_v3_cfg_t const uart1_pads[] = {
  70         MX6_PAD_GPIO1_IO04__UART1_TX | MUX_PAD_CTRL(UART_PAD_CTRL),
  71         MX6_PAD_GPIO1_IO05__UART1_RX | MUX_PAD_CTRL(UART_PAD_CTRL),
  72 };
  73
  74 static iomux_v3_cfg_t const usdhc2_pads[] = {
  75         MX6_PAD_SD2_CLK__USDHC2_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
  76         MX6_PAD_SD2_CMD__USDHC2_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
  77         MX6_PAD_SD2_DATA0__USDHC2_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
  78         MX6_PAD_SD2_DATA1__USDHC2_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
  79         MX6_PAD_SD2_DATA2__USDHC2_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
  80         MX6_PAD_SD2_DATA3__USDHC2_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
  81 };
  82
  83 static iomux_v3_cfg_t const usdhc3_pads[] = {
  84         MX6_PAD_SD3_CLK__USDHC3_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
  85         MX6_PAD_SD3_CMD__USDHC3_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
  86         MX6_PAD_SD3_DATA0__USDHC3_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
  87         MX6_PAD_SD3_DATA1__USDHC3_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
  88         MX6_PAD_SD3_DATA2__USDHC3_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
  89         MX6_PAD_SD3_DATA3__USDHC3_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
  90         MX6_PAD_SD3_DATA4__USDHC3_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
  91         MX6_PAD_SD3_DATA5__USDHC3_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
  92         MX6_PAD_SD3_DATA6__USDHC3_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
  93         MX6_PAD_SD3_DATA7__USDHC3_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
  94
  95         /* CD pin */
  96         MX6_PAD_KEY_COL0__GPIO2_IO_10 | MUX_PAD_CTRL(NO_PAD_CTRL),
  97
  98         /* RST_B, used for power reset cycle */
  99         MX6_PAD_KEY_COL1__GPIO2_IO_11 | MUX_PAD_CTRL(NO_PAD_CTRL),
 100 };
 101
 102 static iomux_v3_cfg_t const usdhc4_pads[] = {
 103         MX6_PAD_SD4_CLK__USDHC4_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
 104         MX6_PAD_SD4_CMD__USDHC4_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
 105         MX6_PAD_SD4_DATA0__USDHC4_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
 106         MX6_PAD_SD4_DATA1__USDHC4_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
 107         MX6_PAD_SD4_DATA2__USDHC4_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
 108         MX6_PAD_SD4_DATA3__USDHC4_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
 109         MX6_PAD_SD4_DATA7__GPIO6_IO_21 | MUX_PAD_CTRL(NO_PAD_CTRL),
 110 };
 111
 112 static iomux_v3_cfg_t const fec1_pads[] = {
 113         MX6_PAD_ENET1_MDC__ENET1_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL),
 114         MX6_PAD_ENET1_MDIO__ENET1_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL),
 115         MX6_PAD_RGMII1_RX_CTL__ENET1_RX_EN | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
 116         MX6_PAD_RGMII1_RD0__ENET1_RX_DATA_0 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
 117         MX6_PAD_RGMII1_RD1__ENET1_RX_DATA_1 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
 118         MX6_PAD_RGMII1_RD2__ENET1_RX_DATA_2 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
 119         MX6_PAD_RGMII1_RD3__ENET1_RX_DATA_3 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
 120         MX6_PAD_RGMII1_RXC__ENET1_RX_CLK | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
 121         MX6_PAD_RGMII1_TX_CTL__ENET1_TX_EN | MUX_PAD_CTRL(ENET_PAD_CTRL),
 122         MX6_PAD_RGMII1_TD0__ENET1_TX_DATA_0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
 123         MX6_PAD_RGMII1_TD1__ENET1_TX_DATA_1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
 124         MX6_PAD_RGMII1_TD2__ENET1_TX_DATA_2 | MUX_PAD_CTRL(ENET_PAD_CTRL),
 125         MX6_PAD_RGMII1_TD3__ENET1_TX_DATA_3 | MUX_PAD_CTRL(ENET_PAD_CTRL),
 126         MX6_PAD_RGMII1_TXC__ENET1_RGMII_TXC | MUX_PAD_CTRL(ENET_PAD_CTRL),
 127 };
 128
 129 static iomux_v3_cfg_t const peri_3v3_pads[] = {
 130         MX6_PAD_QSPI1A_DATA0__GPIO4_IO_16 | MUX_PAD_CTRL(NO_PAD_CTRL),
 131 };
 132
 133 static iomux_v3_cfg_t const phy_control_pads[] = {
 134         /* 25MHz Ethernet PHY Clock */
 135         MX6_PAD_ENET2_RX_CLK__ENET2_REF_CLK_25M | MUX_PAD_CTRL(ENET_CLK_PAD_CTRL),
 136
 137         /* ENET PHY Power */
 138         MX6_PAD_ENET2_COL__GPIO2_IO_6 | MUX_PAD_CTRL(NO_PAD_CTRL),
 139
 140         /* AR8031 PHY Reset */
 141         MX6_PAD_ENET2_CRS__GPIO2_IO_7 | MUX_PAD_CTRL(NO_PAD_CTRL),
 142 };
 143
 144 static void setup_iomux_uart(void)
 145 {
 146         imx_iomux_v3_setup_multiple_pads(uart1_pads, ARRAY_SIZE(uart1_pads));
 147 }
 148
 149 static int setup_fec(void)
 150 {
 151         struct iomuxc *iomuxc_regs = (struct iomuxc *)IOMUXC_BASE_ADDR;
 152         struct anatop_regs *anatop = (struct anatop_regs *)ANATOP_BASE_ADDR;
 153         int reg;
 154
 155         /* Use 125MHz anatop loopback REF_CLK1 for ENET1 */
 156         clrsetbits_le32(&iomuxc_regs->gpr[1], IOMUX_GPR1_FEC1_MASK, 0);
 157
 158         imx_iomux_v3_setup_multiple_pads(phy_control_pads,
 159                                          ARRAY_SIZE(phy_control_pads));
 160
 161         /* Enable the ENET power, active low */
 162         gpio_direction_output(IMX_GPIO_NR(2, 6) , 0);
 163
 164         /* Reset AR8031 PHY */
 165         gpio_direction_output(IMX_GPIO_NR(2, 7) , 0);
 166         udelay(500);
 167         gpio_set_value(IMX_GPIO_NR(2, 7), 1);
 168
 169         reg = readl(&anatop->pll_enet);
 170         reg |= BM_ANADIG_PLL_ENET_REF_25M_ENABLE;
 171         writel(reg, &anatop->pll_enet);
 172
 173         return enable_fec_anatop_clock(ENET_125MHZ);
 174 }
 175
 176 int board_eth_init(bd_t *bis)
 177 {
 178         imx_iomux_v3_setup_multiple_pads(fec1_pads, ARRAY_SIZE(fec1_pads));
 179         setup_fec();
 180
 181         return cpu_eth_init(bis);
 182 }
 183
 184 #define PC MUX_PAD_CTRL(I2C_PAD_CTRL)
 185 /* I2C1 for PMIC */
 186 static struct i2c_pads_info i2c_pad_info1 = {
 187         .scl = {
 188                 .i2c_mode = MX6_PAD_GPIO1_IO00__I2C1_SCL | PC,
 189                 .gpio_mode = MX6_PAD_GPIO1_IO00__GPIO1_IO_0 | PC,
 190                 .gp = IMX_GPIO_NR(1, 0),
 191         },
 192         .sda = {
 193                 .i2c_mode = MX6_PAD_GPIO1_IO01__I2C1_SDA | PC,
 194                 .gpio_mode = MX6_PAD_GPIO1_IO01__GPIO1_IO_1 | PC,
 195                 .gp = IMX_GPIO_NR(1, 1),
 196         },
 197 };
 198
 199 int power_init_board(void)
 200 {
 201         struct pmic *p;
 202         unsigned int reg, ret;
 203
 204         p = pfuze_common_init(I2C_PMIC);
 205         if (!p)
 206                 return -ENODEV;
 207
 208         ret = pfuze_mode_init(p, APS_PFM);
 209         if (ret < 0)
 210                 return ret;
 211
 212         /* Enable power of VGEN5 3V3, needed for SD3 */
 213         pmic_reg_read(p, PFUZE100_VGEN5VOL, &reg);
 214         reg &= ~LDO_VOL_MASK;
 215         reg |= (LDOB_3_30V | (1 << LDO_EN));
 216         pmic_reg_write(p, PFUZE100_VGEN5VOL, reg);
 217
 218         return 0;
 219 }
 220
 221 #ifdef CONFIG_USB_EHCI_MX6
 222 #define USB_OTHERREGS_OFFSET    0x800
 223 #define UCTRL_PWR_POL           (1 << 9)
 224
 225 static iomux_v3_cfg_t const usb_otg_pads[] = {
 226         /* OGT1 */
 227         MX6_PAD_GPIO1_IO09__USB_OTG1_PWR | MUX_PAD_CTRL(NO_PAD_CTRL),
 228         MX6_PAD_GPIO1_IO10__ANATOP_OTG1_ID | MUX_PAD_CTRL(NO_PAD_CTRL),
 229         /* OTG2 */
 230         MX6_PAD_GPIO1_IO12__USB_OTG2_PWR | MUX_PAD_CTRL(NO_PAD_CTRL)
 231 };
 232
 233 static void setup_usb(void)
 234 {
 235         imx_iomux_v3_setup_multiple_pads(usb_otg_pads,
 236                                          ARRAY_SIZE(usb_otg_pads));
 237 }
 238
 239 int board_usb_phy_mode(int port)
 240 {
 241         if (port == 1)
 242                 return USB_INIT_HOST;
 243         else
 244                 return usb_phy_mode(port);
 245 }
 246
 247 int board_ehci_hcd_init(int port)
 248 {
 249         u32 *usbnc_usb_ctrl;
 250
 251         if (port > 1)
 252                 return -EINVAL;
 253
 254         usbnc_usb_ctrl = (u32 *)(USB_BASE_ADDR + USB_OTHERREGS_OFFSET +
 255                                  port * 4);
 256
 257         /* Set Power polarity */
 258         setbits_le32(usbnc_usb_ctrl, UCTRL_PWR_POL);
 259
 260         return 0;
 261 }
 262 #endif
 263
 264 int board_phy_config(struct phy_device *phydev)
 265 {
 266         /*
 267          * Enable 1.8V(SEL_1P5_1P8_POS_REG) on
 268          * Phy control debug reg 0
 269          */
 270         phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x1f);
 271         phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x8);
 272
 273         /* rgmii tx clock delay enable */
 274         phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x05);
 275         phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x100);
 276
 277         if (phydev->drv->config)
 278                 phydev->drv->config(phydev);
 279
 280         return 0;
 281 }
 282
 283 int board_early_init_f(void)
 284 {
 285         setup_iomux_uart();
 286
 287         /* Enable PERI_3V3, which is used by SD2, ENET, LVDS, BT */
 288         imx_iomux_v3_setup_multiple_pads(peri_3v3_pads,
 289                                          ARRAY_SIZE(peri_3v3_pads));
 290
 291         /* Active high for ncp692 */
 292         gpio_direction_output(IMX_GPIO_NR(4, 16) , 1);
 293
 294 #ifdef CONFIG_USB_EHCI_MX6
 295         setup_usb();
 296 #endif
 297
 298         return 0;
 299 }
 300
 301 static struct fsl_esdhc_cfg usdhc_cfg[3] = {
 302         {USDHC2_BASE_ADDR, 0, 4},
 303         {USDHC3_BASE_ADDR},
 304         {USDHC4_BASE_ADDR},
 305 };
 306
 307 #define USDHC3_CD_GPIO  IMX_GPIO_NR(2, 10)
 308 #define USDHC3_PWR_GPIO IMX_GPIO_NR(2, 11)
 309 #define USDHC4_CD_GPIO  IMX_GPIO_NR(6, 21)
 310
 311 int board_mmc_getcd(struct mmc *mmc)
 312 {
 313         struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
 314         int ret = 0;
 315
 316         switch (cfg->esdhc_base) {
 317         case USDHC2_BASE_ADDR:
 318                 ret = 1; /* Assume uSDHC2 is always present */
 319                 break;
 320         case USDHC3_BASE_ADDR:
 321                 ret = !gpio_get_value(USDHC3_CD_GPIO);
 322                 break;
 323         case USDHC4_BASE_ADDR:
 324                 ret = !gpio_get_value(USDHC4_CD_GPIO);
 325                 break;
 326         }
 327
 328         return ret;
 329 }
 330
 331 int board_mmc_init(bd_t *bis)
 332 {
 333 #ifndef CONFIG_SPL_BUILD
 334         int i, ret;
 335
 336         /*
 337          * According to the board_mmc_init() the following map is done:
 338          * (U-boot device node)    (Physical Port)
 339          * mmc0                    USDHC2
 340          * mmc1                    USDHC3
 341          * mmc2                    USDHC4
 342          */
 343         for (i = 0; i < CONFIG_SYS_FSL_USDHC_NUM; i++) {
 344                 switch (i) {
 345                 case 0:
 346                         imx_iomux_v3_setup_multiple_pads(
 347                                 usdhc2_pads, ARRAY_SIZE(usdhc2_pads));
 348                         usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK);
 349                         break;
 350                 case 1:
 351                         imx_iomux_v3_setup_multiple_pads(
 352                                 usdhc3_pads, ARRAY_SIZE(usdhc3_pads));
 353                         gpio_direction_input(USDHC3_CD_GPIO);
 354                         gpio_direction_output(USDHC3_PWR_GPIO, 1);
 355                         usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
 356                         break;
 357                 case 2:
 358                         imx_iomux_v3_setup_multiple_pads(
 359                                 usdhc4_pads, ARRAY_SIZE(usdhc4_pads));
 360                         gpio_direction_input(USDHC4_CD_GPIO);
 361                         usdhc_cfg[2].sdhc_clk = mxc_get_clock(MXC_ESDHC4_CLK);
 362                         break;
 363                 default:
 364                         printf("Warning: you configured more USDHC controllers"
 365                                 "(%d) than supported by the board\n", i + 1);
 366                         return -EINVAL;
 367                         }
 368
 369                         ret = fsl_esdhc_initialize(bis, &usdhc_cfg[i]);
 370                         if (ret) {
 371                                 printf("Warning: failed to initialize mmc dev %d\n", i);
 372                                 return ret;
 373                         }
 374         }
 375
 376         return 0;
 377 #else
 378         struct src *src_regs = (struct src *)SRC_BASE_ADDR;
 379         u32 val;
 380         u32 port;
 381
 382         val = readl(&src_regs->sbmr1);
 383
 384         if ((val & 0xc0) != 0x40) {
 385                 printf("Not boot from USDHC!\n");
 386                 return -EINVAL;
 387         }
 388
 389         port = (val >> 11) & 0x3;
 390         printf("port %d\n", port);
 391         switch (port) {
 392         case 1:
 393                 imx_iomux_v3_setup_multiple_pads(
 394                         usdhc2_pads, ARRAY_SIZE(usdhc2_pads));
 395                 usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK);
 396                 usdhc_cfg[0].esdhc_base = USDHC2_BASE_ADDR;
 397                 break;
 398         case 2:
 399                 imx_iomux_v3_setup_multiple_pads(
 400                         usdhc3_pads, ARRAY_SIZE(usdhc3_pads));
 401                 gpio_direction_input(USDHC3_CD_GPIO);
 402                 gpio_direction_output(USDHC3_PWR_GPIO, 1);
 403                 usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
 404                 usdhc_cfg[0].esdhc_base = USDHC3_BASE_ADDR;
 405                 break;
 406         case 3:
 407                 imx_iomux_v3_setup_multiple_pads(
 408                         usdhc4_pads, ARRAY_SIZE(usdhc4_pads));
 409                 gpio_direction_input(USDHC4_CD_GPIO);
 410                 usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC4_CLK);
 411                 usdhc_cfg[0].esdhc_base = USDHC4_BASE_ADDR;
 412                 break;
 413         }
 414
 415         gd->arch.sdhc_clk = usdhc_cfg[0].sdhc_clk;
 416         return fsl_esdhc_initialize(bis, &usdhc_cfg[0]);
 417 #endif
 418 }
 419
 420 #ifdef CONFIG_FSL_QSPI
 421
 422 #define QSPI_PAD_CTRL1  \
 423         (PAD_CTL_SRE_FAST | PAD_CTL_SPEED_HIGH | \
 424          PAD_CTL_PKE | PAD_CTL_PUE | PAD_CTL_PUS_47K_UP | PAD_CTL_DSE_40ohm)
 425
 426 static iomux_v3_cfg_t const quadspi_pads[] = {
 427         MX6_PAD_NAND_WP_B__QSPI2_A_DATA_0       | MUX_PAD_CTRL(QSPI_PAD_CTRL1),
 428         MX6_PAD_NAND_READY_B__QSPI2_A_DATA_1    | MUX_PAD_CTRL(QSPI_PAD_CTRL1),
 429         MX6_PAD_NAND_CE0_B__QSPI2_A_DATA_2      | MUX_PAD_CTRL(QSPI_PAD_CTRL1),
 430         MX6_PAD_NAND_CE1_B__QSPI2_A_DATA_3      | MUX_PAD_CTRL(QSPI_PAD_CTRL1),
 431         MX6_PAD_NAND_ALE__QSPI2_A_SS0_B         | MUX_PAD_CTRL(QSPI_PAD_CTRL1),
 432         MX6_PAD_NAND_CLE__QSPI2_A_SCLK          | MUX_PAD_CTRL(QSPI_PAD_CTRL1),
 433         MX6_PAD_NAND_DATA07__QSPI2_A_DQS        | MUX_PAD_CTRL(QSPI_PAD_CTRL1),
 434         MX6_PAD_NAND_DATA01__QSPI2_B_DATA_0     | MUX_PAD_CTRL(QSPI_PAD_CTRL1),
 435         MX6_PAD_NAND_DATA00__QSPI2_B_DATA_1     | MUX_PAD_CTRL(QSPI_PAD_CTRL1),
 436         MX6_PAD_NAND_WE_B__QSPI2_B_DATA_2       | MUX_PAD_CTRL(QSPI_PAD_CTRL1),
 437         MX6_PAD_NAND_RE_B__QSPI2_B_DATA_3       | MUX_PAD_CTRL(QSPI_PAD_CTRL1),
 438         MX6_PAD_NAND_DATA03__QSPI2_B_SS0_B      | MUX_PAD_CTRL(QSPI_PAD_CTRL1),
 439         MX6_PAD_NAND_DATA02__QSPI2_B_SCLK       | MUX_PAD_CTRL(QSPI_PAD_CTRL1),
 440         MX6_PAD_NAND_DATA05__QSPI2_B_DQS        | MUX_PAD_CTRL(QSPI_PAD_CTRL1),
 441 };
 442
 443 int board_qspi_init(void)
 444 {
 445         /* Set the iomux */
 446         imx_iomux_v3_setup_multiple_pads(quadspi_pads,
 447                                          ARRAY_SIZE(quadspi_pads));
 448
 449         /* Set the clock */
 450         enable_qspi_clk(1);
 451
 452         return 0;
 453 }
 454 #endif
 455
 456 int board_init(void)
 457 {
 458         /* Address of boot parameters */
 459         gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
 460
 461 #ifdef CONFIG_SYS_I2C_MXC
 462         setup_i2c(0, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info1);
 463 #endif
 464
 465 #ifdef CONFIG_FSL_QSPI
 466         board_qspi_init();
 467 #endif
 468
 469         return 0;
 470 }
 471
 472 int checkboard(void)
 473 {
 474         puts("Board: MX6SX SABRE SDB\n");
 475
 476         return 0;
 477 }
 478
 479 #ifdef CONFIG_SPL_BUILD
 480 #include <libfdt.h>
 481 #include <spl.h>
 482 #include <asm/arch/mx6-ddr.h>
 483
 484 const struct mx6sx_iomux_ddr_regs mx6_ddr_ioregs = {
 485         .dram_dqm0 = 0x00000028,
 486         .dram_dqm1 = 0x00000028,
 487         .dram_dqm2 = 0x00000028,
 488         .dram_dqm3 = 0x00000028,
 489         .dram_ras = 0x00000020,
 490         .dram_cas = 0x00000020,
 491         .dram_odt0 = 0x00000020,
 492         .dram_odt1 = 0x00000020,
 493         .dram_sdba2 = 0x00000000,
 494         .dram_sdcke0 = 0x00003000,
 495         .dram_sdcke1 = 0x00003000,
 496         .dram_sdclk_0 = 0x00000030,
 497         .dram_sdqs0 = 0x00000028,
 498         .dram_sdqs1 = 0x00000028,
 499         .dram_sdqs2 = 0x00000028,
 500         .dram_sdqs3 = 0x00000028,
 501         .dram_reset = 0x00000020,
 502 };
 503
 504 const struct mx6sx_iomux_grp_regs mx6_grp_ioregs = {
 505         .grp_addds = 0x00000020,
 506         .grp_ddrmode_ctl = 0x00020000,
 507         .grp_ddrpke = 0x00000000,
 508         .grp_ddrmode = 0x00020000,
 509         .grp_b0ds = 0x00000028,
 510         .grp_b1ds = 0x00000028,
 511         .grp_ctlds = 0x00000020,
 512         .grp_ddr_type = 0x000c0000,
 513         .grp_b2ds = 0x00000028,
 514         .grp_b3ds = 0x00000028,
 515 };
 516
 517 const struct mx6_mmdc_calibration mx6_mmcd_calib = {
 518         .p0_mpwldectrl0 = 0x00290025,
 519         .p0_mpwldectrl1 = 0x00220022,
 520         .p0_mpdgctrl0 = 0x41480144,
 521         .p0_mpdgctrl1 = 0x01340130,
 522         .p0_mprddlctl = 0x3C3E4244,
 523         .p0_mpwrdlctl = 0x34363638,
 524 };
 525
 526 static struct mx6_ddr3_cfg mem_ddr = {
 527         .mem_speed = 1600,
 528         .density = 4,
 529         .width = 32,
 530         .banks = 8,
 531         .rowaddr = 15,
 532         .coladdr = 10,
 533         .pagesz = 2,
 534         .trcd = 1375,
 535         .trcmin = 4875,
 536         .trasmin = 3500,
 537 };
 538
 539 static void ccgr_init(void)
 540 {
 541         struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
 542
 543         writel(0xFFFFFFFF, &ccm->CCGR0);
 544         writel(0xFFFFFFFF, &ccm->CCGR1);
 545         writel(0xFFFFFFFF, &ccm->CCGR2);
 546         writel(0xFFFFFFFF, &ccm->CCGR3);
 547         writel(0xFFFFFFFF, &ccm->CCGR4);
 548         writel(0xFFFFFFFF, &ccm->CCGR5);
 549         writel(0xFFFFFFFF, &ccm->CCGR6);
 550         writel(0xFFFFFFFF, &ccm->CCGR7);
 551 }
 552
 553 static void spl_dram_init(void)
 554 {
 555         struct mx6_ddr_sysinfo sysinfo = {
 556                 .dsize = mem_ddr.width/32,
 557                 .cs_density = 24,
 558                 .ncs = 1,
 559                 .cs1_mirror = 0,
 560                 .rtt_wr = 2,
 561                 .rtt_nom = 2,           /* RTT_Nom = RZQ/2 */
 562                 .walat = 1,             /* Write additional latency */
 563                 .ralat = 5,             /* Read additional latency */
 564                 .mif3_mode = 3,         /* Command prediction working mode */
 565                 .bi_on = 1,             /* Bank interleaving enabled */
 566                 .sde_to_rst = 0x10,     /* 14 cycles, 200us (JEDEC default) */
 567                 .rst_to_cke = 0x23,     /* 33 cycles, 500us (JEDEC default) */
 568         };
 569
 570         mx6sx_dram_iocfg(mem_ddr.width, &mx6_ddr_ioregs, &mx6_grp_ioregs);
 571         mx6_dram_cfg(&sysinfo, &mx6_mmcd_calib, &mem_ddr);
 572 }
 573
 574 void board_init_f(ulong dummy)
 575 {
 576         /* setup AIPS and disable watchdog */
 577         arch_cpu_init();
 578
 579         ccgr_init();
 580
 581         /* iomux and setup of i2c */
 582         board_early_init_f();
 583
 584         /* setup GP timer */
 585         timer_init();
 586
 587         /* UART clocks enabled and gd valid - init serial console */
 588         preloader_console_init();
 589
 590         /* DDR initialization */
 591         spl_dram_init();
 592
 593         /* Clear the BSS. */
 594         memset(__bss_start, 0, __bss_end - __bss_start);
 595
 596         /* load/boot image from boot device */
 597         board_init_r(NULL, 0);
 598 }
 599
 600 void reset_cpu(ulong addr)
 601 {
 602 }
 603 #endif