4 HiKey is the first certified 96Boards Consumer Edition board. The board/SoC has: -
5 * HiSilicon Kirin 6220 eight-core ARM Cortex-A53 64-bit SoC running at 1.2GHz.
7 * 1GB 800MHz LPDDR3 DRAM
8 * 4GB eMMC Flash Storage
10 * 802.11a/b/g/n WiFi, Bluetooth
12 The HiKey schematic can be found here: -
13 https://github.com/96boards/documentation/blob/master/hikey/96Boards-Hikey-Rev-A1.pdf
15 A SoC datasheet can be found here: -
16 https://github.com/96boards/documentation/blob/master/hikey/
17 Hi6220V100_Multi-Mode_Application_Processor_Function_Description.pdf
19 Currently the u-boot port supports: -
28 > mkdir -p ./aarch64/bin
30 > git clone http://git.denx.de/u-boot.git
31 > make CROSS_COMPILE=aarch64-linux-gnu- hikey_config
32 > make CROSS_COMPILE=aarch64-linux-gnu-
33 > cp u-boot.bin ./aarch64/bin/u-boot-hikey.bin
35 ARM Trusted Firmware (ATF) & l-loader
36 =====================================
38 This u-boot port has been tested with l-loader, booting ATF, which then boots
39 u-boot as the bl33.bin executable.
41 Get the BL30 mcu binary.
42 > wget -P aarch64/bin https://builds.96boards.org/releases/hikey/linaro/binaries/15.05/mcuimage.bin
44 1. Get ATF source code
46 > git clone https://github.com/96boards/arm-trusted-firmware.git
47 > cd ./arm-trusted-firmware
49 2. Compile ATF, I use the build-tf.mak in the directory with this README, and copy it to ATF directory
50 > cp ../u-boot/board/hisilicon/hikey/build-tf.mak .
51 > make -f build-tf.mak build
55 > git clone https://github.com/96boards/l-loader.git
58 4. Make sym links to ATF bl1 / fip binaries
59 > ln -s ../bin/bl1-hikey.bin bl1.bin
60 > ln -s ../bin/fip-hikey.bin fip.bin
62 > arm-linux-gnueabihf-gcc -c -o start.o start.S
63 > arm-linux-gnueabihf-gcc -c -o debug.o debug.S
64 > arm-linux-gnueabihf-ld -Bstatic -Tl-loader.lds -Ttext 0xf9800800 start.o debug.o -o loader
65 > arm-linux-gnueabihf-objcopy -O binary loader temp
66 > python gen_loader.py -o ../bin/l-loader.bin --img_loader=temp --img_bl1=bl1.bin
67 > sudo bash -x generate_ptable.sh
68 > python gen_loader.py -o ../bin/ptable.img --img_prm_ptable=./prm_ptable.img --img_sec_ptable=./sec_ptable.img
70 These instructions are adapted from
71 https://github.com/96boards/documentation/wiki/HiKeyUEFI
76 1. Connect the second jumper on J15 BOOT SEL, to go into recovery mode and flash l-loader.bin with
77 fastboot using the hisi-idt.py utility.
80 > git clone https://github.com/96boards/burn-boot.git
82 The command below assumes HiKey enumerated as the first USB serial port
83 > sudo ./burn-boot/hisi-idt.py -d /dev/ttyUSB0 --img1=./bin/l-loader.bin
85 2. Once LED 0 comes on solid, it should be detected as a fastboot device by plugging a USB A to mini B
86 cable from your PC to the USB OTG port of HiKey (on some boards I've found this to be unreliable).
88 > sudo fastboot devices
90 0123456789ABCDEF fastboot
93 > wget -P aarch64/bin wget https://builds.96boards.org/releases/hikey/linaro/binaries/latest/nvme.img
94 > sudo fastboot flash ptable ./bin/ptable.img
95 > sudo fastboot flash fastboot ./bin/fip-hikey.bin
96 > sudo fastboot flash nvme ./bin/nvme.img
98 4. Disconnect second jumper on J15 BOOT SEL, and reset the board and you will now (hopefully)
99 have ATF, booting u-boot from eMMC. On 'new' boards I've had to do the
100 flashing twice in the past to avoid an ATF error.
102 Note: To get USB host working, also disconnect the USB OTG cable used for flashing. Otherwise you
103 will get 'dwc_otg_core_host_init: Timeout!' errors.
105 See working boot trace below: -
107 debug EMMC boot: send RST_N .
108 debug EMMC boot: start eMMC boot......
111 Switch to aarch64 mode. CPU0 executes at 0xf9801000!
113 INFO: BL1: 0xf9810000 - 0xf9817000 [size = 28672]
114 NOTICE: Booting Trusted Firmware
115 NOTICE: BL1: v1.1(debug):e8b7174
116 NOTICE: BL1: Built : 19:16:44, Sep 8 2015
117 INFO: BL1: RAM 0xf9810000 - 0xf9817000
118 NOTICE: syspll frequency:1190494208Hz
119 NOTICE: succeed to init lpddr3 rank0 dram phy
120 INFO: lpddr3_freq_init, set ddrc 533mhz
121 INFO: init ddr3 rank0
122 INFO: ddr3 rank1 init pass
123 INFO: lpddr3_freq_init, set ddrc 800mhz
124 INFO: init ddr3 rank0
125 INFO: ddr3 rank1 init pass
127 INFO: ddr test value:0xa5a55a5a
128 INFO: Hisilicon HiKey platform is initialized
130 INFO: Loading file 'bl2.bin' at address 0xf9818000
131 INFO: File 'bl2.bin' loaded: 0xf9818000 - 0xf9821100
132 NOTICE: BL1: Booting BL2
133 INFO: BL1: BL2 address = 0xf9818000
134 INFO: BL1: BL2 spsr = 0x3c5
135 INFO: [BDID] [fff91c18] midr: 0x410fd033
136 INFO: [BDID] [fff91c1c] board type: 0
137 INFO: [BDID] [fff91c20] board id: 0x2b
138 INFO: init_acpu_dvfs: pmic version 17
139 INFO: init_acpu_dvfs: ACPU_CHIP_MAX_FREQ=0x186a00.
140 INFO: acpu_dvfs_volt_init: success!
141 INFO: acpu_dvfs_set_freq: support freq num is 5
142 INFO: acpu_dvfs_set_freq: start prof is 0x4
143 INFO: acpu_dvfs_set_freq: magic is 0x5a5ac5c5
144 INFO: acpu_dvfs_set_freq: voltage:
150 NOTICE: acpu_dvfs_set_freq: set acpu freq success!NOTICE: BL2: v1.1(debug):e8b7174
151 NOTICE: BL2: Built : 19:16:46, Sep 8 2015
152 INFO: BL2: Loading BL3-0
154 INFO: Loading file 'bl30.bin' at address 0x1000000
155 INFO: Skip reserving memory: 0x1000000 - 0x1023270
156 INFO: File 'bl30.bin' loaded: 0x1000000 - 0x1023270
157 INFO: bl2_plat_handle_bl30: [1000000] 3a334d43 34313032 2f38302f 30203133
158 INFO: bl2_plat_handle_bl30: [10000c8] 0 0 b 0
159 INFO: bl2_plat_handle_bl30: [1000190] 17 0 0 0
160 INFO: bl2_plat_handle_bl30: [1023260] 0 0 0 0
161 INFO: hisi_mcu_load_image: mcu sections 0:
162 INFO: hisi_mcu_load_image: src = 0x1000200
163 INFO: hisi_mcu_load_image: dst = 0xf6000000
164 INFO: hisi_mcu_load_image: size = 512
165 INFO: hisi_mcu_load_image: [SRC 0x1000200] 0x7600 0x201 0x1eae1 0x1ea71
166 INFO: hisi_mcu_load_image: [DST 0xf6000000] 0x7600 0x201 0x1eae1 0x1ea71
167 INFO: hisi_mcu_load_image: mcu sections 1:
168 INFO: hisi_mcu_load_image: src = 0x1000400
169 INFO: hisi_mcu_load_image: dst = 0xf6000200
170 INFO: hisi_mcu_load_image: size = 27828
171 INFO: hisi_mcu_load_image: [SRC 0x1000400] 0xbf00bf00 0x4815b672 0x48154780 0x60014915
172 INFO: hisi_mcu_load_image: [DST 0xf6000200] 0xbf00bf00 0x4815b672 0x48154780 0x60014915
173 INFO: hisi_mcu_load_image: mcu sections 2:
174 INFO: hisi_mcu_load_image: src = 0x10070b4
175 INFO: hisi_mcu_load_image: dst = 0xf6007200
176 INFO: hisi_mcu_load_image: size = 1024
177 INFO: hisi_mcu_load_image: [SRC 0x10070b4] 0x55 0x0 0x0 0x0
178 INFO: hisi_mcu_load_image: [DST 0xf6007200] 0x55 0x0 0x0 0x0
179 INFO: hisi_mcu_load_image: mcu sections 3:
180 INFO: hisi_mcu_load_image: src = 0x10074b4
181 INFO: hisi_mcu_load_image: dst = 0xfff8e000
182 INFO: hisi_mcu_load_image: size = 12704
183 INFO: hisi_mcu_load_image: [SRC 0x10074b4] 0x55 0x0 0x0 0x0
184 INFO: hisi_mcu_load_image: [DST 0xfff8e000] 0x55 0x0 0x0 0x0
185 INFO: hisi_mcu_load_image: mcu sections 4:
186 INFO: hisi_mcu_load_image: src = 0x100a654
187 INFO: hisi_mcu_load_image: dst = 0x5e00000
188 INFO: hisi_mcu_load_image: size = 82912
189 INFO: hisi_mcu_load_image: [SRC 0x100a654] 0x4ff0e92d 0x2cc5f645 0x2600b0ab 0x2c7cf6c0
190 INFO: hisi_mcu_load_image: [DST 0x5e00000] 0x4ff0e92d 0x2cc5f645 0x2600b0ab 0x2c7cf6c0
191 INFO: hisi_mcu_load_image: mcu sections 5:
192 INFO: hisi_mcu_load_image: src = 0x101ea34
193 INFO: hisi_mcu_load_image: dst = 0x5e143e0
194 INFO: hisi_mcu_load_image: size = 12816
195 INFO: hisi_mcu_load_image: [SRC 0x101ea34] 0x33323130 0x37363534 0x42413938 0x46454443
196 INFO: hisi_mcu_load_image: [DST 0x5e143e0] 0x33323130 0x37363534 0x42413938 0x46454443
197 INFO: hisi_mcu_load_image: mcu sections 6:
198 INFO: hisi_mcu_load_image: src = 0x1021c44
199 INFO: hisi_mcu_load_image: dst = 0x5e1c1d0
200 INFO: hisi_mcu_load_image: size = 3060
201 INFO: hisi_mcu_load_image: [SRC 0x1021c44] 0x0 0x0 0x0 0x0
202 INFO: hisi_mcu_load_image: [DST 0x5e1c1d0] 0x0 0x0 0x0 0x0
203 INFO: hisi_mcu_load_image: mcu sections 7:
204 INFO: hisi_mcu_load_image: src = 0x1022838
205 INFO: hisi_mcu_load_image: dst = 0x5e1cdc4
206 INFO: hisi_mcu_load_image: size = 2616
207 INFO: hisi_mcu_load_image: [SRC 0x1022838] 0xf80000a0 0x0 0xf80000ac 0x0
208 INFO: hisi_mcu_load_image: [DST 0x5e1cdc4] 0xf80000a0 0x0 0xf80000ac 0x0
209 INFO: hisi_mcu_start_run: AO_SC_SYS_CTRL2=0
210 INFO: bl2_plat_handle_bl30: mcu pc is 42933301
211 INFO: bl2_plat_handle_bl30: AO_SC_PERIPH_CLKSTAT4 is 39018f09
212 INFO: BL2: TrustZone: protecting 16777216 bytes of memory at 0x3f000000
213 INFO: BL2: Loading BL3-1
215 INFO: Loading file 'bl31.bin' at address 0xf9858000
216 INFO: File 'bl31.bin' loaded: 0xf9858000 - 0xf9861010
217 INFO: BL2: Loading BL3-2
219 WARNING: Failed to access image 'bl32.bin' (-1)
220 WARNING: Failed to load BL3-2 (-1)
221 INFO: BL2: Loading BL3-3
223 INFO: Loading file 'bl33.bin' at address 0x35000000
224 INFO: File 'bl33.bin' loaded: 0x35000000 - 0x3504c468
225 NOTICE: BL1: Booting BL3-1
226 INFO: BL1: BL3-1 address = 0xf9858000
227 INFO: BL1: BL3-1 spsr = 0x3cd
228 INFO: BL1: BL3-1 params address = 0xf9821920
229 INFO: BL1: BL3-1 plat params address = 0x0
230 NOTICE: BL3-1: v1.1(debug):e8b7174
231 NOTICE: BL3-1: Built : 19:16:49, Sep 8 2015
232 INFO: BL3-1: Initializing runtime services
233 INFO: BL3-1: Preparing for EL3 exit to normal world
234 INFO: BL3-1: Next image address = 0x35000000
235 INFO: BL3-1: Next image spsr = 0x3c9
237 U-Boot 2015.10-rc2 (Sep 08 2015 - 20:29:33 +0100)hikey
241 MMC: config_sd_carddetect: SD card not present
242 HiKey DWMMC: 0, HiKey DWMMC: 1
243 Card did not respond to voltage select!
244 ** Bad device mmc 1 **
245 Using default environment
250 Net: Net Initialization Skipped
252 Hit any key to stop autoboot: 0
254 USB0: Core Release: 3.00a
255 scanning bus 0 for devices... 2 USB Device(s) found
256 scanning usb for storage devices... 0 Storage Device(s) found
257 scanning usb for ethernet devices... 0 Ethernet Device(s) found