2 * (C) Copyright 2007-2008
3 * Stelian Pop <stelian@popies.net>
4 * Lead Tech Design <www.leadtechdesign.com>
5 * Copyright (C) 2008 Ronetix Ilko Iliev (www.ronetix.at)
6 * Copyright (C) 2009 Jean-Christopher PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
8 * SPDX-License-Identifier: GPL-2.0+
12 #include <linux/sizes.h>
15 #include <asm/arch/at91sam9_smc.h>
16 #include <asm/arch/at91_common.h>
17 #include <asm/arch/at91_rstc.h>
18 #include <asm/arch/at91_matrix.h>
19 #include <asm/arch/clk.h>
20 #include <asm/arch/gpio.h>
23 #include <atmel_lcdc.h>
24 #include <dataflash.h>
25 #if defined(CONFIG_RESET_PHY_R) && defined(CONFIG_DRIVER_DM9000)
29 #include <asm/mach-types.h>
31 DECLARE_GLOBAL_DATA_PTR;
33 /* ------------------------------------------------------------------------- */
35 * Miscelaneous platform dependent initialisations
38 #ifdef CONFIG_CMD_NAND
39 static void pm9261_nand_hw_init(void)
42 struct at91_smc *smc = (struct at91_smc *)ATMEL_BASE_SMC;
43 struct at91_matrix *matrix = (struct at91_matrix *)ATMEL_BASE_MATRIX;
46 csa = readl(&matrix->csa) | AT91_MATRIX_CSA_EBI_CS3A;
47 writel(csa, &matrix->csa);
49 /* Configure SMC CS3 for NAND/SmartMedia */
50 writel(AT91_SMC_SETUP_NWE(1) | AT91_SMC_SETUP_NCS_WR(0) |
51 AT91_SMC_SETUP_NRD(1) | AT91_SMC_SETUP_NCS_RD(0),
54 writel(AT91_SMC_PULSE_NWE(3) | AT91_SMC_PULSE_NCS_WR(3) |
55 AT91_SMC_PULSE_NRD(3) | AT91_SMC_PULSE_NCS_RD(3),
58 writel(AT91_SMC_CYCLE_NWE(5) | AT91_SMC_CYCLE_NRD(5),
61 writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE |
62 AT91_SMC_MODE_EXNW_DISABLE |
63 #ifdef CONFIG_SYS_NAND_DBW_16
64 AT91_SMC_MODE_DBW_16 |
65 #else /* CONFIG_SYS_NAND_DBW_8 */
68 AT91_SMC_MODE_TDF_CYCLE(2),
71 at91_periph_clk_enable(ATMEL_ID_PIOA);
72 at91_periph_clk_enable(ATMEL_ID_PIOC);
74 /* Configure RDY/BSY */
75 gpio_direction_input(CONFIG_SYS_NAND_READY_PIN);
77 /* Enable NandFlash */
78 gpio_direction_output(CONFIG_SYS_NAND_ENABLE_PIN, 1);
80 at91_set_a_periph(AT91_PIO_PORTC, 0, 0); /* NANDOE */
81 at91_set_a_periph(AT91_PIO_PORTC, 1, 0); /* NANDWE */
86 #ifdef CONFIG_DRIVER_DM9000
87 static void pm9261_dm9000_hw_init(void)
89 struct at91_smc *smc = (struct at91_smc *)ATMEL_BASE_SMC;
91 /* Configure SMC CS2 for DM9000 */
92 writel(AT91_SMC_SETUP_NWE(2) | AT91_SMC_SETUP_NCS_WR(0) |
93 AT91_SMC_SETUP_NRD(2) | AT91_SMC_SETUP_NCS_RD(0),
96 writel(AT91_SMC_PULSE_NWE(4) | AT91_SMC_PULSE_NCS_WR(8) |
97 AT91_SMC_PULSE_NRD(4) | AT91_SMC_PULSE_NCS_RD(8),
100 writel(AT91_SMC_CYCLE_NWE(16) | AT91_SMC_CYCLE_NRD(16),
103 writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE |
104 AT91_SMC_MODE_EXNW_DISABLE |
105 AT91_SMC_MODE_BAT | AT91_SMC_MODE_DBW_16 |
106 AT91_SMC_MODE_TDF_CYCLE(1),
109 /* Configure Interrupt pin as input, no pull-up */
110 at91_periph_clk_enable(ATMEL_ID_PIOA);
111 at91_set_pio_input(AT91_PIO_PORTA, 24, 0);
116 vidinfo_t panel_info = {
120 .vl_sync = ATMEL_LCDC_INVLINE_INVERTED |
121 ATMEL_LCDC_INVFRAME_INVERTED,
126 .vl_right_margin = 33,
128 .vl_upper_margin = 1,
129 .vl_lower_margin = 0,
130 .mmio = ATMEL_BASE_LCDC,
133 void lcd_enable(void)
135 at91_set_pio_value(AT91_PIO_PORTA, 22, 0); /* power up */
138 void lcd_disable(void)
140 at91_set_pio_value(AT91_PIO_PORTA, 22, 1); /* power down */
143 static void pm9261_lcd_hw_init(void)
145 at91_set_a_periph(AT91_PIO_PORTB, 1, 0); /* LCDHSYNC */
146 at91_set_a_periph(AT91_PIO_PORTB, 2, 0); /* LCDDOTCK */
147 at91_set_a_periph(AT91_PIO_PORTB, 3, 0); /* LCDDEN */
148 at91_set_a_periph(AT91_PIO_PORTB, 4, 0); /* LCDCC */
149 at91_set_a_periph(AT91_PIO_PORTB, 7, 0); /* LCDD2 */
150 at91_set_a_periph(AT91_PIO_PORTB, 8, 0); /* LCDD3 */
151 at91_set_a_periph(AT91_PIO_PORTB, 9, 0); /* LCDD4 */
152 at91_set_a_periph(AT91_PIO_PORTB, 10, 0); /* LCDD5 */
153 at91_set_a_periph(AT91_PIO_PORTB, 11, 0); /* LCDD6 */
154 at91_set_a_periph(AT91_PIO_PORTB, 12, 0); /* LCDD7 */
155 at91_set_a_periph(AT91_PIO_PORTB, 15, 0); /* LCDD10 */
156 at91_set_a_periph(AT91_PIO_PORTB, 16, 0); /* LCDD11 */
157 at91_set_a_periph(AT91_PIO_PORTB, 17, 0); /* LCDD12 */
158 at91_set_a_periph(AT91_PIO_PORTB, 18, 0); /* LCDD13 */
159 at91_set_a_periph(AT91_PIO_PORTB, 19, 0); /* LCDD14 */
160 at91_set_a_periph(AT91_PIO_PORTB, 20, 0); /* LCDD15 */
161 at91_set_b_periph(AT91_PIO_PORTB, 23, 0); /* LCDD18 */
162 at91_set_b_periph(AT91_PIO_PORTB, 24, 0); /* LCDD19 */
163 at91_set_b_periph(AT91_PIO_PORTB, 25, 0); /* LCDD20 */
164 at91_set_b_periph(AT91_PIO_PORTB, 26, 0); /* LCDD21 */
165 at91_set_b_periph(AT91_PIO_PORTB, 27, 0); /* LCDD22 */
166 at91_set_b_periph(AT91_PIO_PORTB, 28, 0); /* LCDD23 */
168 at91_system_clk_enable(AT91_PMC_HCK1);
170 gd->fb_base = ATMEL_BASE_SRAM;
173 #ifdef CONFIG_LCD_INFO
177 extern flash_info_t flash_info[];
179 void lcd_show_board_info(void)
181 ulong dram_size, nand_size, flash_size, dataflash_size;
185 lcd_printf ("%s\n", U_BOOT_VERSION);
186 lcd_printf ("(C) 2009 Ronetix GmbH\n");
187 lcd_printf ("support@ronetix.at\n");
188 lcd_printf ("%s CPU at %s MHz",
189 CONFIG_SYS_AT91_CPU_NAME,
190 strmhz(temp, get_cpu_clk_rate()));
193 for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++)
194 dram_size += gd->bd->bi_dram[i].size;
197 for (i = 0; i < CONFIG_SYS_MAX_NAND_DEVICE; i++)
198 nand_size += get_nand_dev_by_index(i)->size;
201 for (i = 0; i < CONFIG_SYS_MAX_FLASH_BANKS; i++)
202 flash_size += flash_info[i].size;
205 for (i = 0; i < CONFIG_SYS_MAX_DATAFLASH_BANKS; i++)
206 dataflash_size += (unsigned int) dataflash_info[i].Device.pages_number *
207 dataflash_info[i].Device.pages_size;
209 lcd_printf ("%ld MB SDRAM, %ld MB NAND\n%ld MB NOR Flash\n"
210 "%ld MB DataFlash\n",
214 dataflash_size >> 20);
216 #endif /* CONFIG_LCD_INFO */
218 #endif /* CONFIG_LCD */
220 int board_early_init_f(void)
222 at91_periph_clk_enable(ATMEL_ID_PIOA);
223 at91_periph_clk_enable(ATMEL_ID_PIOC);
225 at91_seriald_hw_init();
232 /* arch number of PM9261-Board */
233 gd->bd->bi_arch_number = MACH_TYPE_PM9261;
235 /* adress of boot parameters */
236 gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
238 #ifdef CONFIG_CMD_NAND
239 pm9261_nand_hw_init();
241 #ifdef CONFIG_HAS_DATAFLASH
242 at91_spi0_hw_init(1 << 0);
244 #ifdef CONFIG_DRIVER_DM9000
245 pm9261_dm9000_hw_init();
248 pm9261_lcd_hw_init();
253 #ifdef CONFIG_DRIVER_DM9000
254 int board_eth_init(bd_t *bis)
256 return dm9000_initialize(bis);
262 /* dram_init must store complete ramsize in gd->ram_size */
263 gd->ram_size = get_ram_size((void *)PHYS_SDRAM,
268 int dram_init_banksize(void)
270 gd->bd->bi_dram[0].start = PHYS_SDRAM;
271 gd->bd->bi_dram[0].size = PHYS_SDRAM_SIZE;
276 #ifdef CONFIG_RESET_PHY_R
279 #ifdef CONFIG_DRIVER_DM9000
281 * Initialize ethernet HW addr prior to starting Linux,
289 #ifdef CONFIG_DISPLAY_BOARDINFO
290 int checkboard (void)
294 printf ("Board : Ronetix PM9261\n");
295 printf ("Crystal frequency: %8s MHz\n",
296 strmhz(buf, get_main_clk_rate()));
297 printf ("CPU clock : %8s MHz\n",
298 strmhz(buf, get_cpu_clk_rate()));
299 printf ("Master clock : %8s MHz\n",
300 strmhz(buf, get_mck_clk_rate()));