git.sur5r.net Git - u-boot/blob - board/ronetix/pm9261/pm9261.c

   1 /*
   2  * (C) Copyright 2007-2008
   3  * Stelian Pop <stelian@popies.net>
   4  * Lead Tech Design <www.leadtechdesign.com>
   5  * Copyright (C) 2008 Ronetix Ilko Iliev (www.ronetix.at)
   6  * Copyright (C) 2009 Jean-Christopher PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
   7  *
   8  * SPDX-License-Identifier:     GPL-2.0+
   9  */
  10
  11 #include <common.h>
  12 #include <linux/sizes.h>
  13 #include <asm/io.h>
  14 #include <asm/gpio.h>
  15 #include <asm/arch/at91sam9_smc.h>
  16 #include <asm/arch/at91_common.h>
  17 #include <asm/arch/at91_rstc.h>
  18 #include <asm/arch/at91_matrix.h>
  19 #include <asm/arch/clk.h>
  20 #include <asm/arch/gpio.h>
  21
  22 #include <lcd.h>
  23 #include <atmel_lcdc.h>
  24 #include <dataflash.h>
  25 #if defined(CONFIG_RESET_PHY_R) && defined(CONFIG_DRIVER_DM9000)
  26 #include <net.h>
  27 #endif
  28 #include <netdev.h>
  29
  30 DECLARE_GLOBAL_DATA_PTR;
  31
  32 /* ------------------------------------------------------------------------- */
  33 /*
  34  * Miscelaneous platform dependent initialisations
  35  */
  36
  37 #ifdef CONFIG_CMD_NAND
  38 static void pm9261_nand_hw_init(void)
  39 {
  40         unsigned long csa;
  41         struct at91_smc *smc = (struct at91_smc *)ATMEL_BASE_SMC;
  42         struct at91_matrix *matrix = (struct at91_matrix *)ATMEL_BASE_MATRIX;
  43
  44         /* Enable CS3 */
  45         csa = readl(&matrix->csa) | AT91_MATRIX_CSA_EBI_CS3A;
  46         writel(csa, &matrix->csa);
  47
  48         /* Configure SMC CS3 for NAND/SmartMedia */
  49         writel(AT91_SMC_SETUP_NWE(1) | AT91_SMC_SETUP_NCS_WR(0) |
  50                 AT91_SMC_SETUP_NRD(1) | AT91_SMC_SETUP_NCS_RD(0),
  51                 &smc->cs[3].setup);
  52
  53         writel(AT91_SMC_PULSE_NWE(3) | AT91_SMC_PULSE_NCS_WR(3) |
  54                 AT91_SMC_PULSE_NRD(3) | AT91_SMC_PULSE_NCS_RD(3),
  55                 &smc->cs[3].pulse);
  56
  57         writel(AT91_SMC_CYCLE_NWE(5) | AT91_SMC_CYCLE_NRD(5),
  58                 &smc->cs[3].cycle);
  59
  60         writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE |
  61                 AT91_SMC_MODE_EXNW_DISABLE |
  62 #ifdef CONFIG_SYS_NAND_DBW_16
  63                 AT91_SMC_MODE_DBW_16 |
  64 #else /* CONFIG_SYS_NAND_DBW_8 */
  65                 AT91_SMC_MODE_DBW_8 |
  66 #endif
  67                 AT91_SMC_MODE_TDF_CYCLE(2),
  68                 &smc->cs[3].mode);
  69
  70         at91_periph_clk_enable(ATMEL_ID_PIOA);
  71         at91_periph_clk_enable(ATMEL_ID_PIOC);
  72
  73         /* Configure RDY/BSY */
  74         gpio_direction_input(CONFIG_SYS_NAND_READY_PIN);
  75
  76         /* Enable NandFlash */
  77         gpio_direction_output(CONFIG_SYS_NAND_ENABLE_PIN, 1);
  78
  79         at91_set_a_periph(AT91_PIO_PORTC, 0, 0);        /* NANDOE */
  80         at91_set_a_periph(AT91_PIO_PORTC, 1, 0);        /* NANDWE */
  81 }
  82 #endif
  83
  84
  85 #ifdef CONFIG_DRIVER_DM9000
  86 static void pm9261_dm9000_hw_init(void)
  87 {
  88         struct at91_smc *smc = (struct at91_smc *)ATMEL_BASE_SMC;
  89
  90         /* Configure SMC CS2 for DM9000 */
  91         writel(AT91_SMC_SETUP_NWE(2) | AT91_SMC_SETUP_NCS_WR(0) |
  92                 AT91_SMC_SETUP_NRD(2) | AT91_SMC_SETUP_NCS_RD(0),
  93                 &smc->cs[2].setup);
  94
  95         writel(AT91_SMC_PULSE_NWE(4) | AT91_SMC_PULSE_NCS_WR(8) |
  96                 AT91_SMC_PULSE_NRD(4) | AT91_SMC_PULSE_NCS_RD(8),
  97                 &smc->cs[2].pulse);
  98
  99         writel(AT91_SMC_CYCLE_NWE(16) | AT91_SMC_CYCLE_NRD(16),
 100                 &smc->cs[2].cycle);
 101
 102         writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE |
 103                 AT91_SMC_MODE_EXNW_DISABLE |
 104                 AT91_SMC_MODE_BAT | AT91_SMC_MODE_DBW_16 |
 105                 AT91_SMC_MODE_TDF_CYCLE(1),
 106                 &smc->cs[2].mode);
 107
 108         /* Configure Interrupt pin as input, no pull-up */
 109         at91_periph_clk_enable(ATMEL_ID_PIOA);
 110         at91_set_pio_input(AT91_PIO_PORTA, 24, 0);
 111 }
 112 #endif
 113
 114 #ifdef CONFIG_LCD
 115 vidinfo_t panel_info = {
 116         .vl_col =               240,
 117         .vl_row =               320,
 118         .vl_clk =               4965000,
 119         .vl_sync =              ATMEL_LCDC_INVLINE_INVERTED |
 120                                 ATMEL_LCDC_INVFRAME_INVERTED,
 121         .vl_bpix =              3,
 122         .vl_tft =               1,
 123         .vl_hsync_len =         5,
 124         .vl_left_margin =       1,
 125         .vl_right_margin =      33,
 126         .vl_vsync_len =         1,
 127         .vl_upper_margin =      1,
 128         .vl_lower_margin =      0,
 129         .mmio =                 ATMEL_BASE_LCDC,
 130 };
 131
 132 void lcd_enable(void)
 133 {
 134         at91_set_pio_value(AT91_PIO_PORTA, 22, 0);  /* power up */
 135 }
 136
 137 void lcd_disable(void)
 138 {
 139         at91_set_pio_value(AT91_PIO_PORTA, 22, 1);  /* power down */
 140 }
 141
 142 static void pm9261_lcd_hw_init(void)
 143 {
 144         at91_set_a_periph(AT91_PIO_PORTB, 1, 0);        /* LCDHSYNC */
 145         at91_set_a_periph(AT91_PIO_PORTB, 2, 0);        /* LCDDOTCK */
 146         at91_set_a_periph(AT91_PIO_PORTB, 3, 0);        /* LCDDEN */
 147         at91_set_a_periph(AT91_PIO_PORTB, 4, 0);        /* LCDCC */
 148         at91_set_a_periph(AT91_PIO_PORTB, 7, 0);        /* LCDD2 */
 149         at91_set_a_periph(AT91_PIO_PORTB, 8, 0);        /* LCDD3 */
 150         at91_set_a_periph(AT91_PIO_PORTB, 9, 0);        /* LCDD4 */
 151         at91_set_a_periph(AT91_PIO_PORTB, 10, 0);       /* LCDD5 */
 152         at91_set_a_periph(AT91_PIO_PORTB, 11, 0);       /* LCDD6 */
 153         at91_set_a_periph(AT91_PIO_PORTB, 12, 0);       /* LCDD7 */
 154         at91_set_a_periph(AT91_PIO_PORTB, 15, 0);       /* LCDD10 */
 155         at91_set_a_periph(AT91_PIO_PORTB, 16, 0);       /* LCDD11 */
 156         at91_set_a_periph(AT91_PIO_PORTB, 17, 0);       /* LCDD12 */
 157         at91_set_a_periph(AT91_PIO_PORTB, 18, 0);       /* LCDD13 */
 158         at91_set_a_periph(AT91_PIO_PORTB, 19, 0);       /* LCDD14 */
 159         at91_set_a_periph(AT91_PIO_PORTB, 20, 0);       /* LCDD15 */
 160         at91_set_b_periph(AT91_PIO_PORTB, 23, 0);       /* LCDD18 */
 161         at91_set_b_periph(AT91_PIO_PORTB, 24, 0);       /* LCDD19 */
 162         at91_set_b_periph(AT91_PIO_PORTB, 25, 0);       /* LCDD20 */
 163         at91_set_b_periph(AT91_PIO_PORTB, 26, 0);       /* LCDD21 */
 164         at91_set_b_periph(AT91_PIO_PORTB, 27, 0);       /* LCDD22 */
 165         at91_set_b_periph(AT91_PIO_PORTB, 28, 0);       /* LCDD23 */
 166
 167         at91_system_clk_enable(AT91_PMC_HCK1);
 168
 169         gd->fb_base = ATMEL_BASE_SRAM;
 170 }
 171
 172 #ifdef CONFIG_LCD_INFO
 173 #include <nand.h>
 174 #include <version.h>
 175
 176 extern flash_info_t flash_info[];
 177
 178 void lcd_show_board_info(void)
 179 {
 180         ulong dram_size, nand_size, flash_size, dataflash_size;
 181         int i;
 182         char temp[32];
 183
 184         lcd_printf ("%s\n", U_BOOT_VERSION);
 185         lcd_printf ("(C) 2009 Ronetix GmbH\n");
 186         lcd_printf ("support@ronetix.at\n");
 187         lcd_printf ("%s CPU at %s MHz",
 188                 CONFIG_SYS_AT91_CPU_NAME,
 189                 strmhz(temp, get_cpu_clk_rate()));
 190
 191         dram_size = 0;
 192         for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++)
 193                 dram_size += gd->bd->bi_dram[i].size;
 194
 195         nand_size = 0;
 196         for (i = 0; i < CONFIG_SYS_MAX_NAND_DEVICE; i++)
 197                 nand_size += nand_info[i]->size;
 198
 199         flash_size = 0;
 200         for (i = 0; i < CONFIG_SYS_MAX_FLASH_BANKS; i++)
 201                 flash_size += flash_info[i].size;
 202
 203         dataflash_size = 0;
 204         for (i = 0; i < CONFIG_SYS_MAX_DATAFLASH_BANKS; i++)
 205                 dataflash_size += (unsigned int) dataflash_info[i].Device.pages_number *
 206                                 dataflash_info[i].Device.pages_size;
 207
 208         lcd_printf ("%ld MB SDRAM, %ld MB NAND\n%ld MB NOR Flash\n"
 209                         "%ld MB DataFlash\n",
 210                 dram_size >> 20,
 211                 nand_size >> 20,
 212                 flash_size >> 20,
 213                 dataflash_size >> 20);
 214 }
 215 #endif /* CONFIG_LCD_INFO */
 216
 217 #endif /* CONFIG_LCD */
 218
 219 int board_early_init_f(void)
 220 {
 221         at91_periph_clk_enable(ATMEL_ID_PIOA);
 222         at91_periph_clk_enable(ATMEL_ID_PIOC);
 223
 224         at91_seriald_hw_init();
 225
 226         return 0;
 227 }
 228
 229 int board_init(void)
 230 {
 231         /* arch number of PM9261-Board */
 232         gd->bd->bi_arch_number = MACH_TYPE_PM9261;
 233
 234         /* adress of boot parameters */
 235         gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
 236
 237 #ifdef CONFIG_CMD_NAND
 238         pm9261_nand_hw_init();
 239 #endif
 240 #ifdef CONFIG_HAS_DATAFLASH
 241         at91_spi0_hw_init(1 << 0);
 242 #endif
 243 #ifdef CONFIG_DRIVER_DM9000
 244         pm9261_dm9000_hw_init();
 245 #endif
 246 #ifdef CONFIG_LCD
 247         pm9261_lcd_hw_init();
 248 #endif
 249         return 0;
 250 }
 251
 252 #ifdef CONFIG_DRIVER_DM9000
 253 int board_eth_init(bd_t *bis)
 254 {
 255         return dm9000_initialize(bis);
 256 }
 257 #endif
 258
 259 int dram_init(void)
 260 {
 261         /* dram_init must store complete ramsize in gd->ram_size */
 262         gd->ram_size = get_ram_size((void *)PHYS_SDRAM,
 263                                 PHYS_SDRAM_SIZE);
 264         return 0;
 265 }
 266
 267 void dram_init_banksize(void)
 268 {
 269         gd->bd->bi_dram[0].start = PHYS_SDRAM;
 270         gd->bd->bi_dram[0].size = PHYS_SDRAM_SIZE;
 271 }
 272
 273 #ifdef CONFIG_RESET_PHY_R
 274 void reset_phy(void)
 275 {
 276 #ifdef CONFIG_DRIVER_DM9000
 277         /*
 278          * Initialize ethernet HW addr prior to starting Linux,
 279          * needed for nfsroot
 280          */
 281         eth_init();
 282 #endif
 283 }
 284 #endif
 285
 286 #ifdef CONFIG_DISPLAY_BOARDINFO
 287 int checkboard (void)
 288 {
 289         char buf[32];
 290
 291         printf ("Board : Ronetix PM9261\n");
 292         printf ("Crystal frequency: %8s MHz\n",
 293                                         strmhz(buf, get_main_clk_rate()));
 294         printf ("CPU clock        : %8s MHz\n",
 295                                         strmhz(buf, get_cpu_clk_rate()));
 296         printf ("Master clock     : %8s MHz\n",
 297                                         strmhz(buf, get_mck_clk_rate()));
 298
 299         return 0;
 300 }
 301 #endif