git.sur5r.net Git - u-boot/blob - board/sbc8548/ddr.c

   1 /*
   2  * Copyright 2008 Freescale Semiconductor, Inc.
   3  *
   4  * SPDX-License-Identifier:     GPL-2.0
   5  */
   6
   7 #include <common.h>
   8 #include <i2c.h>
   9
  10 #include <fsl_ddr_sdram.h>
  11 #include <fsl_ddr_dimm_params.h>
  12
  13 void fsl_ddr_board_options(memctl_options_t *popts,
  14                                 dimm_params_t *pdimm,
  15                                 unsigned int ctrl_num)
  16 {
  17         /*
  18          * Factors to consider for clock adjust:
  19          *      - number of chips on bus
  20          *      - position of slot
  21          *      - DDR1 vs. DDR2?
  22          *      - ???
  23          *
  24          * This needs to be determined on a board-by-board basis.
  25          *      0110    3/4 cycle late
  26          *      0111    7/8 cycle late
  27          */
  28         popts->clk_adjust = 7;
  29
  30         /*
  31          * Factors to consider for CPO:
  32          *      - frequency
  33          *      - ddr1 vs. ddr2
  34          */
  35         popts->cpo_override = 10;
  36
  37         /*
  38          * Factors to consider for write data delay:
  39          *      - number of DIMMs
  40          *
  41          * 1 = 1/4 clock delay
  42          * 2 = 1/2 clock delay
  43          * 3 = 3/4 clock delay
  44          * 4 = 1   clock delay
  45          * 5 = 5/4 clock delay
  46          * 6 = 3/2 clock delay
  47          */
  48         popts->write_data_delay = 3;
  49
  50         /*
  51          * Factors to consider for half-strength driver enable:
  52          *      - number of DIMMs installed
  53          */
  54         popts->half_strength_driver_enable = 0;
  55 }
  56
  57 #ifdef CONFIG_SPD_EEPROM
  58 /*
  59  * Workaround for hardware errata.  An i2c address conflict
  60  * existed on earlier boards; the workaround moved the DDR
  61  * SPD from 0x51 to 0x53.  So we try and read 0x53 1st, and
  62  * if that fails, then fall back to reading at 0x51.
  63  */
  64 void get_spd(generic_spd_eeprom_t *spd, u8 i2c_address)
  65 {
  66         int ret;
  67
  68 #ifdef ALT_SPD_EEPROM_ADDRESS
  69         if (i2c_address == SPD_EEPROM_ADDRESS) {
  70                 ret = i2c_read(ALT_SPD_EEPROM_ADDRESS, 0, 1, (uchar *)spd,
  71                                 sizeof(generic_spd_eeprom_t));
  72                 if (ret == 0)
  73                         return;         /* Good data at 0x53 */
  74                 memset(spd, 0, sizeof(generic_spd_eeprom_t));
  75         }
  76 #endif
  77         ret = i2c_read(i2c_address, 0, 1, (uchar *)spd,
  78                                 sizeof(generic_spd_eeprom_t));
  79         if (ret) {
  80                 printf("DDR: failed to read SPD from addr %u\n", i2c_address);
  81                 memset(spd, 0, sizeof(generic_spd_eeprom_t));
  82         }
  83 }
  84
  85 #else
  86 /*
  87  *  fixed_sdram init -- doesn't use serial presence detect.
  88  *  Assumes 256MB DDR2 SDRAM SODIMM, without ECC, running at DDR400 speed.
  89  */
  90 phys_size_t fixed_sdram(void)
  91 {
  92         struct ccsr_ddr __iomem *ddr =
  93                 (struct ccsr_ddr __iomem *)(CONFIG_SYS_FSL_DDR_ADDR);
  94
  95         out_be32(&ddr->cs0_bnds,        0x0000007f);
  96         out_be32(&ddr->cs1_bnds,        0x008000ff);
  97         out_be32(&ddr->cs2_bnds,        0x00000000);
  98         out_be32(&ddr->cs3_bnds,        0x00000000);
  99
 100         out_be32(&ddr->cs0_config,      0x80010101);
 101         out_be32(&ddr->cs1_config,      0x80010101);
 102         out_be32(&ddr->cs2_config,      0x00000000);
 103         out_be32(&ddr->cs3_config,      0x00000000);
 104
 105         out_be32(&ddr->timing_cfg_3,    0x00000000);
 106         out_be32(&ddr->timing_cfg_0,    0x00220802);
 107         out_be32(&ddr->timing_cfg_1,    0x38377322);
 108         out_be32(&ddr->timing_cfg_2,    0x0fa044C7);
 109
 110         out_be32(&ddr->sdram_cfg,       0x4300C000);
 111         out_be32(&ddr->sdram_cfg_2,     0x24401000);
 112
 113         out_be32(&ddr->sdram_mode,      0x23C00542);
 114         out_be32(&ddr->sdram_mode_2,    0x00000000);
 115
 116         out_be32(&ddr->sdram_interval,  0x05080100);
 117         out_be32(&ddr->sdram_md_cntl,   0x00000000);
 118         out_be32(&ddr->sdram_data_init, 0x00000000);
 119         out_be32(&ddr->sdram_clk_cntl,  0x03800000);
 120         asm("sync;isync;msync");
 121         udelay(500);
 122
 123         #ifdef CONFIG_DDR_ECC
 124           /* Enable ECC checking */
 125           out_be32(&ddr->sdram_cfg, CONFIG_SYS_DDR_CONTROL | 0x20000000);
 126         #else
 127           out_be32(&ddr->sdram_cfg, CONFIG_SYS_DDR_CONTROL);
 128         #endif
 129
 130         return CONFIG_SYS_SDRAM_SIZE * 1024 * 1024;
 131 }
 132 #endif