git.sur5r.net Git - u-boot/blob - board/technexion/pico-imx7d/pico-imx7d.c

   1 /*
   2  * Copyright (C) 2017 NXP Semiconductors
   3  *
   4  * SPDX-License-Identifier:     GPL-2.0+
   5  */
   6
   7 #include <asm/arch/clock.h>
   8 #include <asm/arch/crm_regs.h>
   9 #include <asm/arch/imx-regs.h>
  10 #include <asm/arch/mx7-pins.h>
  11 #include <asm/arch/sys_proto.h>
  12 #include <asm/gpio.h>
  13 #include <asm/mach-imx/iomux-v3.h>
  14 #include <asm/mach-imx/mxc_i2c.h>
  15 #include <asm/io.h>
  16 #include <common.h>
  17 #include <fsl_esdhc.h>
  18 #include <i2c.h>
  19 #include <miiphy.h>
  20 #include <mmc.h>
  21 #include <netdev.h>
  22 #include <usb.h>
  23 #include <power/pmic.h>
  24 #include <power/pfuze3000_pmic.h>
  25 #include "../../freescale/common/pfuze.h"
  26
  27 DECLARE_GLOBAL_DATA_PTR;
  28
  29 #define UART_PAD_CTRL  (PAD_CTL_DSE_3P3V_49OHM | \
  30         PAD_CTL_PUS_PU100KOHM | PAD_CTL_HYS)
  31
  32 #define USDHC_PAD_CTRL (PAD_CTL_DSE_3P3V_32OHM | PAD_CTL_SRE_SLOW | \
  33         PAD_CTL_HYS | PAD_CTL_PUE | PAD_CTL_PUS_PU47KOHM)
  34
  35 #define ENET_PAD_CTRL  (PAD_CTL_PUS_PU100KOHM | PAD_CTL_DSE_3P3V_49OHM)
  36 #define ENET_PAD_CTRL_MII  (PAD_CTL_DSE_3P3V_32OHM)
  37
  38 #define ENET_RX_PAD_CTRL  (PAD_CTL_PUS_PU100KOHM | PAD_CTL_DSE_3P3V_49OHM)
  39
  40 #define I2C_PAD_CTRL    (PAD_CTL_DSE_3P3V_32OHM | PAD_CTL_SRE_SLOW | \
  41         PAD_CTL_HYS | PAD_CTL_PUE | PAD_CTL_PUS_PU100KOHM)
  42
  43 #ifdef CONFIG_SYS_I2C_MXC
  44 #define PC MUX_PAD_CTRL(I2C_PAD_CTRL)
  45 /* I2C4 for PMIC */
  46 static struct i2c_pads_info i2c_pad_info4 = {
  47         .scl = {
  48                 .i2c_mode = MX7D_PAD_SAI1_RX_SYNC__I2C4_SCL | PC,
  49                 .gpio_mode = MX7D_PAD_SAI1_RX_SYNC__GPIO6_IO16 | PC,
  50                 .gp = IMX_GPIO_NR(6, 16),
  51         },
  52         .sda = {
  53                 .i2c_mode = MX7D_PAD_SAI1_RX_BCLK__I2C4_SDA | PC,
  54                 .gpio_mode = MX7D_PAD_SAI1_RX_BCLK__GPIO6_IO17 | PC,
  55                 .gp = IMX_GPIO_NR(6, 17),
  56         },
  57 };
  58 #endif
  59
  60 int dram_init(void)
  61 {
  62         gd->ram_size = PHYS_SDRAM_SIZE;
  63
  64         return 0;
  65 }
  66
  67 #ifdef CONFIG_POWER
  68 #define I2C_PMIC        3
  69 int power_init_board(void)
  70 {
  71         struct pmic *p;
  72         int ret;
  73         unsigned int reg, rev_id;
  74
  75         ret = power_pfuze3000_init(I2C_PMIC);
  76         if (ret)
  77                 return ret;
  78
  79         p = pmic_get("PFUZE3000");
  80         ret = pmic_probe(p);
  81         if (ret)
  82                 return ret;
  83
  84         pmic_reg_read(p, PFUZE3000_DEVICEID, &reg);
  85         pmic_reg_read(p, PFUZE3000_REVID, &rev_id);
  86         printf("PMIC:  PFUZE3000 DEV_ID=0x%x REV_ID=0x%x\n", reg, rev_id);
  87
  88         /* disable Low Power Mode during standby mode */
  89         pmic_reg_read(p, PFUZE3000_LDOGCTL, &reg);
  90         reg |= 0x1;
  91         pmic_reg_write(p, PFUZE3000_LDOGCTL, reg);
  92
  93         /* SW1A/1B mode set to APS/APS */
  94         reg = 0x8;
  95         pmic_reg_write(p, PFUZE3000_SW1AMODE, reg);
  96         pmic_reg_write(p, PFUZE3000_SW1BMODE, reg);
  97
  98         /* SW1A/1B standby voltage set to 1.025V */
  99         reg = 0xd;
 100         pmic_reg_write(p, PFUZE3000_SW1ASTBY, reg);
 101         pmic_reg_write(p, PFUZE3000_SW1BSTBY, reg);
 102
 103         /* decrease SW1B normal voltage to 0.975V */
 104         pmic_reg_read(p, PFUZE3000_SW1BVOLT, &reg);
 105         reg &= ~0x1f;
 106         reg |= PFUZE3000_SW1AB_SETP(975);
 107         pmic_reg_write(p, PFUZE3000_SW1BVOLT, reg);
 108
 109         return 0;
 110 }
 111 #endif
 112
 113 static iomux_v3_cfg_t const wdog_pads[] = {
 114         MX7D_PAD_GPIO1_IO00__WDOG1_WDOG_B | MUX_PAD_CTRL(NO_PAD_CTRL),
 115 };
 116
 117 static iomux_v3_cfg_t const uart5_pads[] = {
 118         MX7D_PAD_I2C4_SCL__UART5_DCE_RX | MUX_PAD_CTRL(UART_PAD_CTRL),
 119         MX7D_PAD_I2C4_SDA__UART5_DCE_TX | MUX_PAD_CTRL(UART_PAD_CTRL),
 120 };
 121
 122 static iomux_v3_cfg_t const usdhc3_emmc_pads[] = {
 123         MX7D_PAD_SD3_CLK__SD3_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
 124         MX7D_PAD_SD3_CMD__SD3_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
 125         MX7D_PAD_SD3_DATA0__SD3_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
 126         MX7D_PAD_SD3_DATA1__SD3_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
 127         MX7D_PAD_SD3_DATA2__SD3_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
 128         MX7D_PAD_SD3_DATA3__SD3_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
 129         MX7D_PAD_SD3_DATA4__SD3_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
 130         MX7D_PAD_SD3_DATA5__SD3_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
 131         MX7D_PAD_SD3_DATA6__SD3_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
 132         MX7D_PAD_SD3_DATA7__SD3_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
 133         MX7D_PAD_GPIO1_IO14__GPIO1_IO14 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
 134 };
 135
 136 #ifdef CONFIG_FEC_MXC
 137 static iomux_v3_cfg_t const fec1_pads[] = {
 138         MX7D_PAD_SD2_CD_B__ENET1_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL_MII),
 139         MX7D_PAD_SD2_WP__ENET1_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL_MII),
 140         MX7D_PAD_ENET1_RGMII_TXC__ENET1_RGMII_TXC | MUX_PAD_CTRL(ENET_PAD_CTRL),
 141         MX7D_PAD_ENET1_RGMII_TD0__ENET1_RGMII_TD0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
 142         MX7D_PAD_ENET1_RGMII_TD1__ENET1_RGMII_TD1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
 143         MX7D_PAD_ENET1_RGMII_TD2__ENET1_RGMII_TD2 | MUX_PAD_CTRL(ENET_PAD_CTRL),
 144         MX7D_PAD_ENET1_RGMII_TD3__ENET1_RGMII_TD3 | MUX_PAD_CTRL(ENET_PAD_CTRL),
 145         MX7D_PAD_ENET1_RGMII_TX_CTL__ENET1_RGMII_TX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL),
 146         MX7D_PAD_ENET1_RGMII_RXC__ENET1_RGMII_RXC | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
 147         MX7D_PAD_ENET1_RGMII_RD0__ENET1_RGMII_RD0 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
 148         MX7D_PAD_ENET1_RGMII_RD1__ENET1_RGMII_RD1 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
 149         MX7D_PAD_ENET1_RGMII_RD2__ENET1_RGMII_RD2 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
 150         MX7D_PAD_ENET1_RGMII_RD3__ENET1_RGMII_RD3 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
 151         MX7D_PAD_ENET1_RGMII_RX_CTL__ENET1_RGMII_RX_CTL | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
 152         MX7D_PAD_SD3_STROBE__GPIO6_IO10 | MUX_PAD_CTRL(NO_PAD_CTRL),
 153         MX7D_PAD_SD3_RESET_B__GPIO6_IO11 | MUX_PAD_CTRL(NO_PAD_CTRL),
 154 };
 155
 156 #define FEC1_RST_GPIO   IMX_GPIO_NR(6, 11)
 157
 158 static void setup_iomux_fec(void)
 159 {
 160         imx_iomux_v3_setup_multiple_pads(fec1_pads, ARRAY_SIZE(fec1_pads));
 161
 162         gpio_direction_output(FEC1_RST_GPIO, 0);
 163         udelay(500);
 164         gpio_set_value(FEC1_RST_GPIO, 1);
 165 }
 166
 167 int board_eth_init(bd_t *bis)
 168 {
 169         setup_iomux_fec();
 170
 171         return fecmxc_initialize_multi(bis, 0,
 172                 CONFIG_FEC_MXC_PHYADDR, IMX_FEC_BASE);
 173 }
 174
 175 static int setup_fec(void)
 176 {
 177         struct iomuxc_gpr_base_regs *const iomuxc_gpr_regs
 178                 = (struct iomuxc_gpr_base_regs *)IOMUXC_GPR_BASE_ADDR;
 179
 180         /* Use 125M anatop REF_CLK1 for ENET1, clear gpr1[13], gpr1[17] */
 181         clrsetbits_le32(&iomuxc_gpr_regs->gpr[1],
 182                         (IOMUXC_GPR_GPR1_GPR_ENET1_TX_CLK_SEL_MASK |
 183                         IOMUXC_GPR_GPR1_GPR_ENET1_CLK_DIR_MASK), 0);
 184
 185         return set_clk_enet(ENET_125MHz);
 186 }
 187
 188 int board_phy_config(struct phy_device *phydev)
 189 {
 190         unsigned short val;
 191
 192         /* To enable AR8035 ouput a 125MHz clk from CLK_25M */
 193         phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x7);
 194         phy_write(phydev, MDIO_DEVAD_NONE, 0xe, 0x8016);
 195         phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x4007);
 196
 197         val = phy_read(phydev, MDIO_DEVAD_NONE, 0xe);
 198         val &= 0xffe7;
 199         val |= 0x18;
 200         phy_write(phydev, MDIO_DEVAD_NONE, 0xe, val);
 201
 202         /* introduce tx clock delay */
 203         phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x5);
 204         val = phy_read(phydev, MDIO_DEVAD_NONE, 0x1e);
 205         val |= 0x0100;
 206         phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, val);
 207
 208         if (phydev->drv->config)
 209                 phydev->drv->config(phydev);
 210
 211         return 0;
 212 }
 213 #endif
 214
 215 static void setup_iomux_uart(void)
 216 {
 217         imx_iomux_v3_setup_multiple_pads(uart5_pads, ARRAY_SIZE(uart5_pads));
 218 }
 219
 220 static struct fsl_esdhc_cfg usdhc_cfg[1] = {
 221         {USDHC3_BASE_ADDR},
 222 };
 223
 224 int board_mmc_getcd(struct mmc *mmc)
 225 {
 226         /* Assume uSDHC3 emmc is always present */
 227         return 1;
 228 }
 229
 230 int board_mmc_init(bd_t *bis)
 231 {
 232         imx_iomux_v3_setup_multiple_pads(
 233                         usdhc3_emmc_pads, ARRAY_SIZE(usdhc3_emmc_pads));
 234         usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
 235
 236         return fsl_esdhc_initialize(bis, &usdhc_cfg[0]);
 237 }
 238
 239 int board_early_init_f(void)
 240 {
 241         setup_iomux_uart();
 242
 243 #ifdef CONFIG_SYS_I2C_MXC
 244         setup_i2c(3, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info4);
 245 #endif
 246
 247         return 0;
 248 }
 249
 250 int board_init(void)
 251 {
 252         /* address of boot parameters */
 253         gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
 254
 255 #ifdef CONFIG_FEC_MXC
 256         setup_fec();
 257 #endif
 258
 259         return 0;
 260 }
 261
 262 int board_late_init(void)
 263 {
 264         struct wdog_regs *wdog = (struct wdog_regs *)WDOG1_BASE_ADDR;
 265
 266         imx_iomux_v3_setup_multiple_pads(wdog_pads, ARRAY_SIZE(wdog_pads));
 267
 268         set_wdog_reset(wdog);
 269
 270         /*
 271          * Do not assert internal WDOG_RESET_B_DEB(controlled by bit 4),
 272          * since we use PMIC_PWRON to reset the board.
 273          */
 274         clrsetbits_le16(&wdog->wcr, 0, 0x10);
 275
 276         return 0;
 277 }
 278
 279 int checkboard(void)
 280 {
 281         puts("Board: i.MX7D PICOSOM\n");
 282
 283         return 0;
 284 }
 285
 286 int board_usb_phy_mode(int port)
 287 {
 288         return USB_INIT_DEVICE;
 289 }