3 * Sysgo Real-Time Solutions, GmbH <www.elinos.com>
4 * Marius Groeger <mgroeger@sysgo.de>
7 * David Mueller, ELSOFT AG, <d.mueller@elsoft.ch>
10 * Texas Instruments, <www.ti.com>
11 * Kshitij Gupta <Kshitij@ti.com>
14 * Texas Instruments, <www.ti.com>
15 * Rishi Bhattacharya <rishi@ti.com>
17 * See file CREDITS for list of people who contributed to this
20 * This program is free software; you can redistribute it and/or
21 * modify it under the terms of the GNU General Public License as
22 * published by the Free Software Foundation; either version 2 of
23 * the License, or (at your option) any later version.
25 * This program is distributed in the hope that it will be useful,
26 * but WITHOUT ANY WARRANTY; without even the implied warranty of
27 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
28 * GNU General Public License for more details.
30 * You should have received a copy of the GNU General Public License
31 * along with this program; if not, write to the Free Software
32 * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
38 #if defined(CONFIG_OMAP1610)
39 #include <./configs/omap1510.h>
42 DECLARE_GLOBAL_DATA_PTR;
44 void flash__init (void);
45 void ether__init (void);
46 void set_muxconf_regs (void);
47 void peripheral_power_enable (void);
49 #define COMP_MODE_ENABLE ((unsigned int)0x0000EAEF)
51 static inline void delay (unsigned long loops)
53 __asm__ volatile ("1:\n"
55 "bne 1b":"=r" (loops):"0" (loops));
59 * Miscellaneous platform dependent initialisations
64 gd->bd->bi_arch_number = MACH_TYPE_OMAP_OSK;
66 /* adress of boot parameters */
67 gd->bd->bi_boot_params = 0x10000100;
69 /* Configure MUX settings */
71 peripheral_power_enable ();
73 /* this speeds up your boot a quite a bit. However to make it
74 * work, you need make sure your kernel startup flush bug is fixed.
85 int misc_init_r (void)
91 /******************************
94 ******************************/
95 void flash__init (void)
97 #define EMIFS_GlB_Config_REG 0xfffecc0c
99 regval = *((volatile unsigned int *) EMIFS_GlB_Config_REG);
100 /* Turn off write protection for flash devices. */
101 regval = regval | 0x0001;
102 *((volatile unsigned int *) EMIFS_GlB_Config_REG) = regval;
104 /*************************************************************
106 Description: take the Ethernet controller out of reset and wait
107 for the EEPROM load to complete.
108 *************************************************************/
109 void ether__init (void)
111 #define ETH_CONTROL_REG 0x0480000b
114 *((volatile unsigned short *) 0xfffece08) = 0x03FF;
115 *((volatile unsigned short *) 0xfffb3824) = 0x8000;
116 *((volatile unsigned short *) 0xfffb3830) = 0x0000;
117 *((volatile unsigned short *) 0xfffb3834) = 0x0009;
118 *((volatile unsigned short *) 0xfffb3838) = 0x0009;
119 *((volatile unsigned short *) 0xfffb3818) = 0x0002;
120 *((volatile unsigned short *) 0xfffb382C) = 0x0048;
121 *((volatile unsigned short *) 0xfffb3824) = 0x8603;
123 for (i=0;i<2000;i++);
124 *((volatile unsigned short *) 0xfffb381C) = 0x6610;
126 for (i=0;i<10000;i++);
128 *((volatile unsigned char *) ETH_CONTROL_REG) &= ~0x01;
134 /******************************
137 ******************************/
140 gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
141 gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE;
146 /******************************************************
147 Routine: set_muxconf_regs
148 Description: Setting up the configuration Mux registers
149 specific to the hardware
150 *******************************************************/
151 void set_muxconf_regs (void)
153 volatile unsigned int *MuxConfReg;
154 /* set each registers to its reset value; */
156 (volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_0);
157 /* setup for UART1 */
158 *MuxConfReg &= ~(0x02000000); /* bit 25 */
159 /* setup for UART2 */
160 *MuxConfReg &= ~(0x01000000); /* bit 24 */
161 /* Disable Uwire CS Hi-Z */
162 *MuxConfReg |= 0x08000000;
164 (volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_3);
165 *MuxConfReg = 0x00000000;
167 (volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_4);
168 *MuxConfReg = 0x00000000;
170 (volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_5);
171 *MuxConfReg = 0x00000000;
173 (volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_6);
174 /*setup mux for UART3 */
175 *MuxConfReg |= 0x00000001; /* bit3, 1, 0 (mux0 5,5,26) */
176 *MuxConfReg &= ~0x0000003e;
178 (volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_7);
179 *MuxConfReg = 0x00000000;
181 (volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_8);
182 /* Disable Uwire CS Hi-Z */
183 *MuxConfReg |= 0x00001200; /*bit 9 for CS0 12 for CS3 */
185 (volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_9);
186 /* Need to turn on bits 21 and 12 in FUNC_MUX_CTRL_9 so the */
187 /* hardware will actually use TX and RTS based on bit 25 in */
188 /* FUNC_MUX_CTRL_0. I told you this thing was screwy! */
189 *MuxConfReg |= 0x00201000;
191 (volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_A);
192 *MuxConfReg = 0x00000000;
194 (volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_B);
195 *MuxConfReg = 0x00000000;
197 (volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_C);
198 /* setup for UART2 */
199 /* Need to turn on bits 27 and 24 in FUNC_MUX_CTRL_C so the */
200 /* hardware will actually use TX and RTS based on bit 24 in */
201 /* FUNC_MUX_CTRL_0. */
202 *MuxConfReg |= 0x09000000;
204 (volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_D);
205 *MuxConfReg |= 0x00000020;
207 (volatile unsigned int *) ((unsigned int) PULL_DWN_CTRL_0);
208 *MuxConfReg = 0x00000000;
210 (volatile unsigned int *) ((unsigned int) PULL_DWN_CTRL_1);
211 *MuxConfReg = 0x00000000;
212 /* mux setup for SD/MMC driver */
214 (volatile unsigned int *) ((unsigned int) PULL_DWN_CTRL_2);
215 *MuxConfReg &= 0xFFFE0FFF;
217 (volatile unsigned int *) ((unsigned int) PULL_DWN_CTRL_3);
218 *MuxConfReg = 0x00000000;
220 (volatile unsigned int *) ((unsigned int) MOD_CONF_CTRL_0);
221 /* bit 13 for MMC2 XOR_CLK */
222 *MuxConfReg &= ~(0x00002000);
223 /* bit 29 for UART 1 */
224 *MuxConfReg &= ~(0x00002000);
226 (volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_0);
227 /* Configure for USB. Turn on VBUS_CTRL and VBUS_MODE. */
228 *MuxConfReg |= 0x000C0000;
230 (volatile unsigned int *) ((unsigned int)USB_TRANSCEIVER_CTRL);
231 *MuxConfReg &= ~(0x00000070);
232 *MuxConfReg &= ~(0x00000008);
233 *MuxConfReg |= 0x00000003;
234 *MuxConfReg |= 0x00000180;
236 (volatile unsigned int *) ((unsigned int) MOD_CONF_CTRL_0);
237 /* bit 17, software controls VBUS */
238 *MuxConfReg &= ~(0x00020000);
239 /* Enable USB 48 and 12M clocks */
240 *MuxConfReg |= 0x00000200;
241 *MuxConfReg &= ~(0x00000180);
242 /*2.75V for MMCSDIO1 */
244 (volatile unsigned int *) ((unsigned int) VOLTAGE_CTRL_0);
245 *MuxConfReg = 0x00001FE7;
247 (volatile unsigned int *) ((unsigned int) PU_PD_SEL_0);
248 *MuxConfReg = 0x00000000;
250 (volatile unsigned int *) ((unsigned int) PU_PD_SEL_1);
251 *MuxConfReg = 0x00000000;
253 (volatile unsigned int *) ((unsigned int) PU_PD_SEL_2);
254 *MuxConfReg = 0x00000000;
256 (volatile unsigned int *) ((unsigned int) PU_PD_SEL_3);
257 *MuxConfReg = 0x00000000;
259 (volatile unsigned int *) ((unsigned int) PU_PD_SEL_4);
260 *MuxConfReg = 0x00000000;
262 (volatile unsigned int *) ((unsigned int) PULL_DWN_CTRL_4);
263 *MuxConfReg = 0x00000000;
264 /* Turn on UART2 48 MHZ clock */
266 (volatile unsigned int *) ((unsigned int) MOD_CONF_CTRL_0);
267 *MuxConfReg |= 0x40000000;
269 (volatile unsigned int *) ((unsigned int) USB_OTG_CTRL);
270 /* setup for USB VBus detection OMAP161x */
271 *MuxConfReg |= 0x00040000; /* bit 18 */
273 (volatile unsigned int *) ((unsigned int) PU_PD_SEL_2);
274 /* PullUps for SD/MMC driver */
275 *MuxConfReg |= ~(0xFFFE0FFF);
277 (volatile unsigned int *) ((unsigned int)COMP_MODE_CTRL_0);
278 *MuxConfReg = COMP_MODE_ENABLE;
281 /******************************************************
282 Routine: peripheral_power_enable
283 Description: Enable the power for UART1
284 *******************************************************/
285 void peripheral_power_enable (void)
287 #define UART1_48MHZ_ENABLE ((unsigned short)0x0200)
288 #define SW_CLOCK_REQUEST ((volatile unsigned short *)0xFFFE0834)
290 *SW_CLOCK_REQUEST |= UART1_48MHZ_ENABLE;
294 * Check Board Identity
299 int i = getenv_f("serial#", buf, sizeof(buf));
301 puts("Board: OSK5912");
312 #ifdef CONFIG_CMD_NET
313 int board_eth_init(bd_t *bis)
316 #ifdef CONFIG_LAN91C96
317 rc = lan91c96_initialize(0, CONFIG_LAN91C96_BASE);