2 * Copyright 2010 Extreme Engineering Solutions, Inc.
3 * Copyright 2007-2008 Freescale Semiconductor, Inc.
5 * See file CREDITS for list of people who contributed to this
8 * This program is free software; you can redistribute it and/or
9 * modify it under the terms of the GNU General Public License as
10 * published by the Free Software Foundation; either version 2 of
11 * the License, or (at your option) any later version.
13 * This program is distributed in the hope that it will be useful,
14 * but WITHOUT ANY WARRANTY; without even the implied warranty of
15 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
16 * GNU General Public License for more details.
18 * You should have received a copy of the GNU General Public License
19 * along with this program; if not, write to the Free Software
20 * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
27 #include <asm/fsl_ddr_sdram.h>
28 #include <asm/fsl_ddr_dimm_params.h>
30 static void get_spd(ddr3_spd_eeprom_t *spd, unsigned char i2c_address)
32 i2c_read(i2c_address, SPD_EEPROM_OFFSET, 2, (uchar *)spd,
33 sizeof(ddr3_spd_eeprom_t));
36 void fsl_ddr_get_spd(ddr3_spd_eeprom_t *ctrl_dimms_spd,
37 unsigned int ctrl_num)
40 unsigned int i2c_address = 0;
42 for (i = 0; i < CONFIG_DIMM_SLOTS_PER_CTLR; i++) {
43 if (ctrl_num == 0 && i == 0)
44 i2c_address = SPD_EEPROM_ADDRESS1;
45 get_spd(&(ctrl_dimms_spd[i]), i2c_address);
49 unsigned int fsl_ddr_get_mem_data_rate(void)
51 return get_ddr_freq(0);
55 * There are traditionally three board-specific SDRAM timing parameters
56 * which must be calculated based on the particular PCB artwork. These are:
57 * 1.) CPO (Read Capture Delay)
58 * - TIMING_CFG_2 register
59 * Source: Calculation based on board trace lengths and
60 * chip-specific internal delays.
61 * 2.) CLK_ADJUST (Clock and Addr/Cmd alignment control)
62 * - DDR_SDRAM_CLK_CNTL register
63 * Source: Signal Integrity Simulations
64 * 3.) 2T Timing on Addr/Ctl
65 * - TIMING_CFG_2 register
66 * Source: Signal Integrity Simulations
67 * Usually only needed with heavy load/very high speed (>DDR2-800)
69 * ====== XPedite550x DDR3-800 read delay calculations ======
71 * The P2020 processor provides an autoleveling option. Setting CPO to
72 * 0x1f enables this auto configuration.
76 unsigned short datarate_mhz_low;
77 unsigned short datarate_mhz_high;
78 unsigned char clk_adjust;
80 } board_specific_parameters_t;
82 const board_specific_parameters_t board_specific_parameters[][20] = {
87 .datarate_mhz_low = 500,
88 .datarate_mhz_high = 750,
94 .datarate_mhz_low = 750,
95 .datarate_mhz_high = 850,
102 void fsl_ddr_board_options(memctl_options_t *popts,
103 dimm_params_t *pdimm,
104 unsigned int ctrl_num)
106 const board_specific_parameters_t *pbsp =
107 &(board_specific_parameters[ctrl_num][0]);
108 u32 num_params = sizeof(board_specific_parameters[ctrl_num]) /
109 sizeof(board_specific_parameters[0][0]);
114 * Set odt_rd_cfg and odt_wr_cfg. If the there is only one dimm in
115 * that controller, set odt_wr_cfg to 4 for CS0, and 0 to CS1. If
116 * there are two dimms in the controller, set odt_rd_cfg to 3 and
117 * odt_wr_cfg to 3 for the even CS, 0 for the odd CS.
119 for (i = 0; i < CONFIG_CHIP_SELECTS_PER_CTRL; i++) {
120 if (i&1) { /* odd CS */
121 popts->cs_local_opts[i].odt_rd_cfg = 0;
122 popts->cs_local_opts[i].odt_wr_cfg = 0;
123 } else { /* even CS */
124 if (CONFIG_DIMM_SLOTS_PER_CTLR == 1) {
125 popts->cs_local_opts[i].odt_rd_cfg = 0;
126 popts->cs_local_opts[i].odt_wr_cfg = 4;
127 } else if (CONFIG_DIMM_SLOTS_PER_CTLR == 2) {
128 popts->cs_local_opts[i].odt_rd_cfg = 3;
129 popts->cs_local_opts[i].odt_wr_cfg = 3;
135 * Get clk_adjust, cpo, write_data_delay,2T, according to the board ddr
136 * freqency and n_banks specified in board_specific_parameters table.
138 ddr_freq = get_ddr_freq(0) / 1000000;
140 for (i = 0; i < num_params; i++) {
141 if (ddr_freq >= pbsp->datarate_mhz_low &&
142 ddr_freq <= pbsp->datarate_mhz_high) {
143 popts->clk_adjust = pbsp->clk_adjust;
144 popts->cpo_override = pbsp->cpo;
151 * Factors to consider for half-strength driver enable:
152 * - number of DIMMs installed
154 popts->half_strength_driver_enable = 0;
157 * Enable on-die termination.
158 * From the Micron Technical Node TN-41-04, RTT_Nom should typically
159 * be 30 to 40 ohms, while RTT_WR should be 120 ohms. Setting RTT_WR
160 * is handled in the Freescale DDR3 driver. Set RTT_Nom here.
162 popts->rtt_override = 1;
163 popts->rtt_override_value = 3;