1 menu "Command line interface"
4 bool "Support U-Boot commands"
7 Enable U-Boot's command-line functions. This provides a means
8 to enter commands into U-Boot for a wide variety of purposes. It
9 also allows scripts (containing commands) to be executed.
10 Various commands and command categorys can be indivdually enabled.
11 Depending on the number of commands enabled, this can add
12 substantially to the size of U-Boot.
18 This option enables the "hush" shell (from Busybox) as command line
19 interpreter, thus enabling powerful command line syntax like
20 if...then...else...fi conditionals or `&&' and '||'
21 constructs ("shell scripts").
23 If disabled, you get the old, much simpler behaviour with a somewhat
24 smaller memory footprint.
30 This string is displayed in the command line to the left of the
33 menu "Autoboot options"
39 This enables the autoboot. See doc/README.autoboot for detail.
42 bool "Stop autobooting via specific input key / string"
45 This option enables stopping (aborting) of the automatic
46 boot feature only by issuing a specific input key or
47 string. If not enabled, any input key will abort the
48 U-Boot automatic booting process and bring the device
49 to the U-Boot prompt for user input.
51 config AUTOBOOT_PROMPT
52 string "Autoboot stop prompt"
53 depends on AUTOBOOT_KEYED
54 default "Autoboot in %d seconds\\n"
56 This string is displayed before the boot delay selected by
57 CONFIG_BOOTDELAY starts. If it is not defined there is no
58 output indicating that autoboot is in progress.
60 Note that this define is used as the (only) argument to a
61 printf() call, so it may contain '%' format specifications,
62 provided that it also includes, sepearated by commas exactly
63 like in a printf statement, the required arguments. It is
64 the responsibility of the user to select only such arguments
65 that are valid in the given context.
67 config AUTOBOOT_ENCRYPTION
68 bool "Enable encryption in autoboot stopping"
69 depends on AUTOBOOT_KEYED
72 config AUTOBOOT_DELAY_STR
73 string "Delay autobooting via specific input key / string"
74 depends on AUTOBOOT_KEYED && !AUTOBOOT_ENCRYPTION
76 This option delays the automatic boot feature by issuing
77 a specific input key or string. If CONFIG_AUTOBOOT_DELAY_STR
78 or the environment variable "bootdelaykey" is specified
79 and this string is received from console input before
80 autoboot starts booting, U-Boot gives a command prompt. The
81 U-Boot prompt will time out if CONFIG_BOOT_RETRY_TIME is
82 used, otherwise it never times out.
84 config AUTOBOOT_STOP_STR
85 string "Stop autobooting via specific input key / string"
86 depends on AUTOBOOT_KEYED && !AUTOBOOT_ENCRYPTION
88 This option enables stopping (aborting) of the automatic
89 boot feature only by issuing a specific input key or
90 string. If CONFIG_AUTOBOOT_STOP_STR or the environment
91 variable "bootstopkey" is specified and this string is
92 received from console input before autoboot starts booting,
93 U-Boot gives a command prompt. The U-Boot prompt never
94 times out, even if CONFIG_BOOT_RETRY_TIME is used.
96 config AUTOBOOT_KEYED_CTRLC
97 bool "Enable Ctrl-C autoboot interruption"
98 depends on AUTOBOOT_KEYED && !AUTOBOOT_ENCRYPTION
101 This option allows for the boot sequence to be interrupted
102 by ctrl-c, in addition to the "bootdelaykey" and "bootstopkey".
103 Setting this variable provides an escape sequence from the
104 limited "password" strings.
106 config AUTOBOOT_STOP_STR_SHA256
107 string "Stop autobooting via SHA256 encrypted password"
108 depends on AUTOBOOT_KEYED && AUTOBOOT_ENCRYPTION
110 This option adds the feature to only stop the autobooting,
111 and therefore boot into the U-Boot prompt, when the input
112 string / password matches a values that is encypted via
113 a SHA256 hash and saved in the environment.
117 source "cmd/fastboot/Kconfig"
137 Print ".config" contents.
139 If this option is enabled, the ".config" file contents are embedded
140 in the U-Boot image and can be printed on the console by the "config"
141 command. This provides information of which options are enabled on
148 Print console devices and information.
153 Print information about available CPUs. This normally shows the
154 number of CPUs, type (e.g. manufacturer, architecture, product or
155 internal name) and clock frequency. Other information may be
156 available depending on the CPU driver.
162 Print GPL license text
178 Run the command stored in the environment "bootcmd", i.e.
179 "bootd" does the same thing as "run bootcmd".
185 Boot an application image from the memory.
190 Boot the Linux zImage
197 Boot an AArch64 Linux Kernel image from memory.
201 depends on EFI_LOADER
204 Boot an EFI image from memory.
206 config CMD_BOOTEFI_HELLO_COMPILE
207 bool "Compile a standard EFI hello world binary for testing"
208 depends on CMD_BOOTEFI && (ARM || X86)
211 This compiles a standard EFI hello world application with U-Boot so
212 that it can be used with the test/py testing framework. This is useful
213 for testing that EFI is working at a basic level, and for bringing
214 up EFI support on a new architecture.
216 No additional space will be required in the resulting U-Boot binary
217 when this option is enabled.
219 config CMD_BOOTEFI_HELLO
220 bool "Allow booting a standard EFI hello world for testing"
221 depends on CMD_BOOTEFI_HELLO_COMPILE
223 This adds a standard EFI hello world application to U-Boot so that
224 it can be used with the 'bootefi hello' command. This is useful
225 for testing that EFI is working at a basic level, and for bringing
226 up EFI support on a new architecture.
228 source lib/efi_selftest/Kconfig
234 Add an ANSI terminal boot menu command.
237 bool "bootelf, bootvx"
240 Boot an ELF/vxWorks image from the memory.
243 bool "Flattened Device Tree utility commands"
247 Do FDT related setup before booting into the Operating System.
253 Start an application at a given address.
259 Run the command in the given environment variable.
265 Print header information for application image.
270 List all images found in flash
276 Extract a part of a multi-image.
281 Poweroff/Shutdown the system
284 bool "spl export - Export boot information for Falcon boot"
287 Falcon mode allows booting directly from SPL into an Operating
288 System such as Linux, thus skipping U-Boot proper. See
289 doc/README.falcon for full information about how to use this
292 config CMD_SPL_NAND_OFS
293 hex "Offset of OS command line args for Falcon-mode NAND boot"
297 This provides the offset of the command line arguments for Linux
298 when booting from NAND in Falcon mode. See doc/README.falcon
299 for full information about how to use this option (and also see
300 board/gateworks/gw_ventana/README for an example).
302 config CMD_SPL_WRITE_SIZE
303 hex "Size of argument area"
307 This provides the size of the command-line argument area in NAND
308 flash used by Falcon-mode boot. See the documentation until CMD_SPL
311 config CMD_THOR_DOWNLOAD
312 bool "thor - TIZEN 'thor' download"
314 Implements the 'thor' download protocol. This is a way of
315 downloading a software update over USB from an attached host.
316 There is no documentation about this within the U-Boot source code
317 but you should be able to find something on the interwebs.
320 bool "zboot - x86 boot command"
322 With x86 machines it is common to boot a bzImage file which
323 contains both a kernel and a setup.bin file. The latter includes
324 configuration information from the dark ages which x86 boards still
325 need to pick things out of.
327 Consider using FIT in preference to this since it supports directly
328 booting both 32- and 64-bit kernels, as well as secure boot.
329 Documentation is available in doc/uImage.FIT/x86-fit-boot.txt
333 menu "Environment commands"
336 bool "ask for env variable"
338 Ask for environment variable
356 Edit environment variable.
361 Allow for searching environment variables
367 Save all environment variables into the compiled-in persistent
370 config CMD_ENV_EXISTS
374 Check if a variable is defined in the environment for use in
377 config CMD_ENV_CALLBACK
378 bool "env callbacks - print callbacks and their associated variables"
380 Some environment variable have callbacks defined by
381 U_BOOT_ENV_CALLBACK. These are called when the variable changes.
382 For example changing "baudrate" adjust the serial baud rate. This
383 command lists the currently defined callbacks.
386 bool "env flags -print variables that have non-default flags"
388 Some environment variables have special flags that control their
389 behaviour. For example, serial# can only be written once and cannot
390 be deleted. This command shows the variables that have special
395 menu "Memory commands"
400 default n if ARCH_SUNXI
409 Add -v option to verify data against a crc32 checksum.
412 bool "eeprom - EEPROM subsystem"
414 (deprecated, needs conversion to driver model)
415 Provides commands to read and write EEPROM (Electrically Erasable
416 Programmable Read Only Memory) chips that are connected over an
419 config CMD_EEPROM_LAYOUT
420 bool "Enable layout-aware eeprom commands"
421 depends on CMD_EEPROM
423 (deprecated, needs conversion to driver model)
424 When enabled, additional eeprom sub-commands become available.
426 eeprom print - prints the contents of the eeprom in a human-readable
427 way (eeprom layout fields, and data formatted to be fit for human
430 eeprom update - allows user to update eeprom fields by specifying
431 the field name, and providing the new data in a human readable format
432 (same format as displayed by the eeprom print command).
434 Both commands can either auto detect the layout, or be told which
438 __weak int parse_layout_version(char *str)
439 - override to provide your own layout name parsing
440 __weak void __eeprom_layout_assign(struct eeprom_layout *layout,
442 - override to setup the layout metadata based on the version
443 __weak int eeprom_layout_detect(unsigned char *data)
444 - override to provide your own algorithm for detecting layout
447 - contains various printing and updating functions for common
448 types of eeprom fields. Can be used for defining
451 config EEPROM_LAYOUT_HELP_STRING
452 string "Tells user what layout names are supported"
453 depends on CMD_EEPROM_LAYOUT
454 default "<not defined>"
456 Help printed with the LAYOUT VERSIONS part of the 'eeprom'
462 Infinite write loop on address range
469 Compute MD5 checksum.
474 depends on CMD_MD5SUM
476 Add -v option to verify data against an MD5 checksum.
481 Display memory information.
484 bool "md, mm, nm, mw, cp, cmp, base, loop"
489 mm - memory modify (auto-incrementing address)
490 nm - memory modify (constant address)
491 mw - memory write (fill)
494 base - print or set address offset
495 loop - initialize loop on address range
500 Simple RAM read/write test.
505 mdc - memory display cyclic
506 mwc - memory write cyclic
512 Compute SHA1 checksum.
514 config SHA1SUM_VERIFY
516 depends on CMD_SHA1SUM
518 Add -v option to verify data against a SHA1 checksum.
521 bool "strings - display strings in memory"
523 This works similarly to the Unix 'strings' command except that it
524 works with a memory range. String of printable characters found
525 within the range are displayed. The minimum number of characters
526 for a sequence to be considered a string can be provided.
530 menu "Compression commands"
534 default y if CMD_BOOTI
537 Support decompressing an LZMA (Lempel-Ziv-Markov chain algorithm)
542 default n if ARCH_SUNXI
543 default y if CMD_BOOTI
545 Uncompress a zip-compressed memory region.
550 Compress a memory region with zlib deflate method.
554 menu "Device access commands"
557 #depends on FLASH_CFI_DRIVER
560 ARM Ltd reference designs flash partition access
563 bool "clk - Show clock frequencies"
566 Shows clock frequences by calling a sock_clk_dump() hook function.
567 This is depreated in favour of using the CLK uclass and accessing
568 clock values from associated drivers. However currently no command
572 bool "demo - Demonstration commands for driver model"
575 Provides a 'demo' command which can be used to play around with
576 driver model. To use this properly you will need to enable one or
577 both of the demo devices (DM_DEMO_SHAPE and DM_DEMO_SIMPLE).
578 Otherwise you will always get an empty list of devices. The demo
579 devices are defined in the sandbox device tree, so the easiest
580 option is to use sandbox and pass the -d point to sandbox's
585 select USB_FUNCTION_DFU
587 Enables the command "dfu" which is used to have U-Boot create a DFU
588 class device via USB. This command requires that the "dfu_alt_info"
589 environment variable be set and define the alt settings to expose to
593 bool "dm - Access to driver model information"
597 Provides access to driver model data structures and information,
598 such as a list of devices, list of uclasses and the state of each
599 device (e.g. activated). This is not required for operation, but
600 can be useful to see the state of driver model for debugging or
604 bool "fdcboot - Boot from floppy device"
606 The 'fdtboot' command allows booting an image from a floppy disk.
609 bool "flinfo, erase, protect"
613 flinfo - print FLASH memory information
615 protect - enable or disable FLASH write protection
623 config CMD_FPGA_LOADBP
624 bool "fpga loadbp - load partial bitstream (Xilinx only)"
627 Supports loading an FPGA device from a bitstream buffer containing
630 config CMD_FPGA_LOADFS
631 bool "fpga loadfs - load bitstream from FAT filesystem (Xilinx only)"
634 Supports loading an FPGA device from a FAT filesystem.
636 config CMD_FPGA_LOADMK
637 bool "fpga loadmk - load bitstream from image"
640 Supports loading an FPGA device from a image generated by mkimage.
642 config CMD_FPGA_LOADP
643 bool "fpga loadp - load partial bitstream"
646 Supports loading an FPGA device from a bitstream buffer containing
650 bool "fpgad - dump FPGA registers"
652 (legacy, needs conversion to driver model)
653 Provides a way to dump FPGA registers by calling the board-specific
654 fpga_get_reg() function. This functions similarly to the 'md'
658 bool "fuse - support for the fuse subssystem"
660 (deprecated - needs conversion to driver model)
661 This allows reading, sensing, programming or overriding fuses
662 which control the behaviour of the device. The command uses the
671 bool "GPT (GUID Partition Table) command"
672 select PARTITION_UUIDS
676 Enable the 'gpt' command to ready and write GPT style partition
680 bool "GPT Random UUID generation"
682 Enable the generation of partitions with random UUIDs if none
685 config CMD_GPT_RENAME
686 bool "GPT partition renaming commands"
689 Enables the 'gpt' command to interchange names on two GPT
690 partitions via the 'gpt swap' command or to rename single
691 partitions via the 'rename' command.
694 bool "ide - Support for IDE drivers"
697 Provides an 'ide' command which allows accessing the IDE drive,
698 reseting the IDE interface, printing the partition table and
699 geting device info. It also enables the 'diskboot' command which
700 permits booting from an IDE drive.
703 bool "io - Support for performing I/O accesses"
705 Provides an 'iod' command to display I/O space and an 'iow' command
706 to write values to the I/O space. This can be useful for manually
707 checking the state of devices during boot when debugging device
711 bool "iotrace - Support for tracing I/O activity"
713 Provides an 'iotrace' command which supports recording I/O reads and
714 writes in a trace buffer in memory . It also maintains a checksum
715 of the trace records (even if space is exhausted) so that the
716 sequence of I/O accesses can be verified.
718 When debugging drivers it is useful to see what I/O accesses were
719 done and in what order.
721 Even if the individual accesses are of little interest it can be
722 useful to verify that the access pattern is consistent each time
723 an operation is performed. In this case a checksum can be used to
724 characterise the operation of a driver. The checksum can be compared
725 across different runs of the operation to verify that the driver is
728 In particular, when performing major refactoring of the driver, where
729 the access pattern should not change, the checksum provides assurance
730 that the refactoring work has not broken the driver.
732 This works by sneaking into the io.h heder for an architecture and
733 redirecting I/O accesses through iotrace's tracing mechanism.
735 For now no commands are provided to examine the trace buffer. The
736 format is fairly simple, so 'md' is a reasonable substitute.
738 Note: The checksum feature is only useful for I/O regions where the
739 contents do not change outside of software control. Where this is not
740 suitable you can fall back to manually comparing the addresses. It
741 might be useful to enhance tracing to only checksum the accesses and
742 not the data read/written.
753 Load a binary file over serial line.
759 Load an S-Record file over serial line
764 MMC memory mapped support.
768 default y if NAND_SUNXI
773 config CMD_NAND_TRIMFFS
774 bool "nand write.trimffs"
775 default y if ARCH_SUNXI
777 Allows one to skip empty pages when flashing something on a NAND.
779 config CMD_NAND_LOCK_UNLOCK
780 bool "nand lock/unlock"
782 NAND locking support.
784 config CMD_NAND_TORTURE
787 NAND torture support.
796 NVM Express device support
799 bool "mmc_spi - Set up MMC SPI device"
801 Provides a way to set up an MMC (Multimedia Card) SPI (Serial
802 Peripheral Interface) device. The device provides a means of
803 accessing an MMC device via SPI using a single data line, limited
804 to 20MHz. It is useful since it reduces the amount of protocol code
808 bool "onenand - access to onenand device"
810 OneNAND is a brand of NAND ('Not AND' gate) flash which provides
811 various useful features. This command allows reading, writing,
812 and erasing blocks. It allso provides a way to show and change
813 bad blocks, and test the device.
817 select PARTITION_UUIDS
819 Read and display information about the partition table on
823 bool "pci - Access PCI devices"
825 Provide access to PCI (Peripheral Interconnect Bus), a type of bus
826 used on some devices to allow the CPU to communicate with its
827 peripherals. Sub-commands allow bus enumeration, displaying and
828 changing configuration space and a few other features.
831 bool "pinit - Set up PCMCIA device"
833 Provides a means to initialise a PCMCIA (Personal Computer Memory
834 Card International Association) device. This is an old standard from
835 about 1990. These devices are typically removable memory or network
836 cards using a standard 68-pin connector.
839 bool "read - Read binary data from a partition"
841 Provides low-level access to the data in a partition.
843 config CMD_REMOTEPROC
845 depends on REMOTEPROC
847 Support for Remote Processor control
850 bool "sata - Access SATA subsystem"
853 SATA (Serial Advanced Technology Attachment) is a serial bus
854 standard for connecting to hard drives and other storage devices.
855 This command provides information about attached devices and allows
856 reading, writing and other operations.
858 SATA replaces PATA (originally just ATA), which stands for Parallel AT
859 Attachment, where AT refers to an IBM AT (Advanced Technology)
860 computer released in 1984.
863 bool "saves - Save a file over serial in S-Record format"
865 Provides a way to save a binary file using the Motorola S-Record
866 format over the serial line.
869 bool "sdram - Print SDRAM configuration information"
871 Provides information about attached SDRAM. This assumed that the
872 SDRAM has an EEPROM with information that can be read using the
873 I2C bus. This is only available on some boards.
881 bool "sf test - Allow testing of SPI flash"
883 Provides a way to test that SPI flash is working correctly. The
884 test is destructive, in that an area of SPI flash must be provided
885 for the test to use. Performance information is also provided,
886 measuring the performance of reading, writing and erasing in
887 Mbps (Million Bits Per Second). This value should approximately
888 equal the SPI bus speed for a single-bit-wide SPI bus, assuming
889 everything is working properly.
897 bool "tsi148 - Command to access tsi148 device"
899 This provides various sub-commands to initialise and configure the
900 Turndra tsi148 device. See the command help for full details.
903 bool "universe - Command to set up the Turndra Universe controller"
905 This allows setting up the VMEbus provided by this controller.
906 See the command help for full details.
915 select USB_FUNCTION_SDP
917 Enables the command "sdp" which is used to have U-Boot emulating the
918 Serial Download Protocol (SDP) via USB.
921 depends on USB_FUNCTION_ROCKUSB
923 Rockusb protocol is widely used by Rockchip SoC based devices. It can
924 read/write info, image to/from devices. This enable rockusb command
925 support to communication with rockusb device. for more detail about
926 this command, please read doc/README.rockusb.
928 config CMD_USB_MASS_STORAGE
929 bool "UMS usb mass storage"
931 USB mass storage support
936 menu "Shell scripting commands"
948 Return true/false on integer compare.
954 Run script from memory
960 Evaluate boolean and math expressions and store the result in an env
962 Also supports loading the value at a memory location into a variable.
963 If CONFIG_REGEX is enabled, setexpr also supports a gsub function.
967 menu "Network commands"
970 bool "bootp, tftpboot"
975 bootp - boot image via network using BOOTP/TFTP protocol
976 tftpboot - boot image via network using TFTP protocol
981 TFTP put command, for uploading files to a server
986 Act as a TFTP server and boot the first received file
991 Boot image via network using RARP/TFTP protocol
996 Boot image via network using DHCP/TFTP protocol
1002 Boot image via network using PXE protocol
1008 Boot image via network using NFS protocol.
1013 Enable MII utility commands.
1018 Send ICMP ECHO_REQUEST to network host
1023 Perform CDP network configuration
1028 Synchronize RTC via network
1033 Lookup the IP of a hostname
1035 config CMD_LINK_LOCAL
1038 Acquire a network IP address using the link-local protocol
1043 Allow control of L2 Ethernet switch commands. These are supported
1044 by the vsc9953 Ethernet driver at present. Sub-commands allow
1045 operations such as enabling / disabling a port and
1046 viewing/maintaining the filtering database (FDB)
1050 menu "Misc commands"
1053 bool "Enable 'bmp' command"
1054 depends on LCD || DM_VIDEO || VIDEO
1056 This provides a way to obtain information about a BMP-format iamge
1057 and to display it. BMP (which presumably stands for BitMaP) is a
1058 file format defined by Microsoft which supports images of various
1059 depths, formats and compression methods. Headers on the file
1060 determine the formats used. This command can be used by first loading
1061 the image into RAM, then using this command to look at it or display
1065 bool "Enable board-specific commands"
1067 (deprecated: instead, please define a Kconfig option for each command)
1069 Some boards have board-specific commands which are only enabled
1070 during developemnt and need to be turned off for production. This
1071 option provides a way to control this. The commands that are enabled
1072 vary depending on the board.
1074 config CMD_BKOPS_ENABLE
1075 bool "mmc bkops enable"
1079 Enable command for setting manual background operations handshake
1080 on a eMMC device. The feature is optionally available on eMMC devices
1081 conforming to standard >= 4.41.
1083 config CMD_BLOCK_CACHE
1084 bool "blkcache - control and stats for block cache"
1085 depends on BLOCK_CACHE
1086 default y if BLOCK_CACHE
1088 Enable the blkcache command, which can be used to control the
1089 operation of the cache functions.
1090 This is most useful when fine-tuning the operation of the cache
1091 during development, but also allows the cache to be disabled when
1092 it might hurt performance (e.g. when using the ums command).
1095 bool "icache or dcache"
1097 Enable the "icache" and "dcache" commands
1100 bool "Enable the 'display' command, for character displays"
1102 (this needs porting to driver model)
1103 This enables the 'display' command which allows a string to be
1104 displayed on a simple board-specific display. Implement
1105 display_putc() to use it.
1111 Enable the 'led' command which allows for control of LEDs supported
1112 by the board. The LEDs can be listed with 'led list' and controlled
1113 with led on/off/togle/blink. Any LED drivers can be controlled with
1114 this command, e.g. led_gpio.
1120 Enable the 'date' command for getting/setting the time/date in RTC
1126 Run commands and summarize execution time.
1129 bool "gettime - read elapsed time"
1131 Enable the 'gettime' command which reads the elapsed time since
1132 U-Boot started running. This shows the time in seconds and
1133 milliseconds. See also the 'bootstage' command which provides more
1134 flexibility for boot timing.
1136 # TODO: rename to CMD_SLEEP
1141 Delay execution for some time
1146 Access the system timer.
1152 This provides basic access to the U-Boot's sound support. The main
1153 feature is to play a beep.
1155 sound init - set up sound system
1156 sound play - play a sound
1162 This provides access to the QEMU firmware interface. The main
1163 feature is to allow easy loading of files passed to qemu-system
1164 via -kernel / -initrd
1166 source "cmd/mvebu/Kconfig"
1169 bool "terminal - provides a way to attach a serial terminal"
1171 Provides a 'cu'-like serial terminal command. This can be used to
1172 access other serial ports from the system console. The terminal
1173 is very simple with no special processing of characters. As with
1174 cu, you can press ~. (tilde followed by period) to exit.
1177 bool "uuid, guid - generation of unique IDs"
1179 This enables two commands:
1181 uuid - generate random Universally Unique Identifier
1182 guid - generate Globally Unique Identifier based on random UUID
1184 The two commands are very similar except for the endianness of the
1189 source "cmd/ti/Kconfig"
1191 config CMD_BOOTSTAGE
1192 bool "Enable the 'bootstage' command"
1193 depends on BOOTSTAGE
1195 Add a 'bootstage' command which supports printing a report
1196 and un/stashing of bootstage data.
1198 menu "Power commands"
1200 bool "Enable Driver Model PMIC command"
1203 This is the pmic command, based on a driver model pmic's API.
1204 Command features are unchanged:
1205 - list - list pmic devices
1206 - pmic dev <id> - show or [set] operating pmic device (NEW)
1207 - pmic dump - dump registers
1208 - pmic read address - read byte of register at address
1209 - pmic write address - write byte to register at address
1210 The only one change for this command is 'dev' subcommand.
1212 config CMD_REGULATOR
1213 bool "Enable Driver Model REGULATOR command"
1214 depends on DM_REGULATOR
1216 This command is based on driver model regulator's API.
1217 User interface features:
1218 - list - list regulator devices
1219 - regulator dev <id> - show or [set] operating regulator device
1220 - regulator info - print constraints info
1221 - regulator status - print operating status
1222 - regulator value <val] <-f> - print/[set] voltage value [uV]
1223 - regulator current <val> - print/[set] current value [uA]
1224 - regulator mode <id> - print/[set] operating mode id
1225 - regulator enable - enable the regulator output
1226 - regulator disable - disable the regulator output
1228 The '-f' (force) option can be used for set the value which exceeds
1229 the limits, which are found in device-tree and are kept in regulator's
1230 uclass platdata structure.
1234 menu "Security commands"
1236 bool "Enable the 'aes' command"
1239 This provides a means to encrypt and decrypt data using the AES
1240 (Advanced Encryption Standard). This algorithm uses a symetric key
1241 and is widely used as a streaming cipher. Different key lengths are
1242 supported by the algorithm but this command only supports 128 bits
1246 bool "Enable the 'blob' command"
1248 This is used with the Freescale secure boot mechanism.
1250 Freescale's SEC block has built-in Blob Protocol which provides
1251 a method for protecting user-defined data across system power
1252 cycles. SEC block protects data in a data structure called a Blob,
1253 which provides both confidentiality and integrity protection.
1255 Encapsulating data as a blob
1256 Each time that the Blob Protocol is used to protect data, a
1257 different randomly generated key is used to encrypt the data.
1258 This random key is itself encrypted using a key which is derived
1259 from SoC's non-volatile secret key and a 16 bit Key identifier.
1260 The resulting encrypted key along with encrypted data is called a
1261 blob. The non-volatile secure key is available for use only during
1264 During decapsulation, the reverse process is performed to get back
1268 blob enc - encapsulating data as a cryptgraphic blob
1269 blob dec - decapsulating cryptgraphic blob to get the data
1273 blob enc src dst len km
1275 Encapsulate and create blob of data $len bytes long
1276 at address $src and store the result at address $dst.
1277 $km is the 16 byte key modifier is also required for
1278 generation/use as key for cryptographic operation. Key
1279 modifier should be 16 byte long.
1281 blob dec src dst len km
1283 Decapsulate the blob of data at address $src and
1284 store result of $len byte at addr $dst.
1285 $km is the 16 byte key modifier is also required for
1286 generation/use as key for cryptographic operation. Key
1287 modifier should be 16 byte long.
1290 bool "Support 'hash' command"
1293 This provides a way to hash data in memory using various supported
1294 algorithms (such as SHA1, MD5, CRC32). The computed digest can be
1295 saved to memory or to an environment variable. It is also possible
1296 to verify a hash against data in memory.
1302 Add -v option to verify data against a hash.
1305 bool "Enable the 'tpm' command"
1308 This provides a means to talk to a TPM from the command line. A wide
1309 range of commands if provided - see 'tpm help' for details. The
1310 command requires a suitable TPM on your board and the correct driver
1314 bool "Enable the 'tpm test' command"
1317 This provides a a series of tests to confirm that the TPM is working
1318 correctly. The tests cover initialisation, non-volatile RAM, extend,
1319 global lock and checking that timing is within expectations. The
1320 tests pass correctly on Infineon TPMs but may need to be adjusted
1325 menu "Firmware commands"
1327 bool "Enable crosec command"
1331 Enable command-line access to the Chrome OS EC (Embedded
1332 Controller). This provides the 'crosec' command which has
1333 a number of sub-commands for performing EC tasks such as
1334 updating its flash, accessing a small saved context area
1335 and talking to the I2C bus behind the EC (if there is one).
1338 menu "Filesystem commands"
1340 bool "Enable the 'btrsubvol' command"
1343 This enables the 'btrsubvol' command to list subvolumes
1344 of a BTRFS filesystem. There are no special commands for
1345 listing BTRFS directories or loading BTRFS files - this
1346 can be done by the generic 'fs' commands (see CMD_FS_GENERIC)
1347 when BTRFS is enabled (see FS_BTRFS).
1350 bool "Enable the 'cbfs' command"
1353 Define this to enable support for reading from a Coreboot
1354 filesystem. This is a ROM-based filesystem used for accessing files
1355 on systems that use coreboot as the first boot-loader and then load
1356 U-Boot to actually boot the Operating System. Available commands are
1357 cbfsinit, cbfsinfo, cbfsls and cbfsload.
1360 bool "Enable the 'cramfs' command"
1361 depends on FS_CRAMFS
1363 This provides commands for dealing with CRAMFS (Compressed ROM
1364 filesystem). CRAMFS is useful when space is tight since files are
1365 compressed. Two commands are provided:
1367 cramfsls - lists files in a cramfs image
1368 cramfsload - loads a file from a cramfs image
1371 bool "ext2 command support"
1373 Enables EXT2 FS command
1376 bool "ext4 command support"
1378 Enables EXT4 FS command
1380 config CMD_EXT4_WRITE
1382 bool "ext4 write command support"
1384 Enables EXT4 FS write command
1387 bool "FAT command support"
1390 Support for the FAT fs
1392 config CMD_FS_GENERIC
1393 bool "filesystem commands"
1395 Enables filesystem commands (e.g. load, ls) that work for multiple
1399 bool "fsuuid command"
1401 Enables fsuuid command for filesystem UUID.
1404 bool "jffs2 command"
1407 Enables commands to support the JFFS2 (Journalling Flash File System
1408 version 2) filesystem. This enables fsload, ls and fsinfo which
1409 provide the ability to load files, list directories and obtain
1410 filesystem information.
1413 bool "MTD partition support"
1415 MTD partition support
1417 config MTDIDS_DEFAULT
1418 string "Default MTD IDs"
1419 depends on CMD_MTDPARTS || CMD_NAND || CMD_FLASH
1421 Defines a default MTD IDs list for use with MTD partitions in the
1422 Linux MTD command line partitions format.
1424 config MTDPARTS_DEFAULT
1425 string "Default MTD partition scheme"
1426 depends on CMD_MTDPARTS || CMD_NAND || CMD_FLASH
1428 Defines a default MTD partitioning scheme in the Linux MTD command
1429 line partitions format
1431 config CMD_MTDPARTS_SPREAD
1432 bool "Padd partition size to take account of bad blocks"
1433 depends on CMD_MTDPARTS
1435 This enables the 'spread' sub-command of the mtdparts command.
1436 This command will modify the existing mtdparts variable by increasing
1437 the size of the partitions such that 1) each partition's net size is
1438 at least as large as the size specified in the mtdparts variable and
1439 2) each partition starts on a good block.
1442 bool "reiser - Access to reiserfs filesystems"
1444 This provides two commands which operate on a resierfs filesystem,
1445 commonly used some years ago:
1447 reiserls - list files
1448 reiserload - load a file
1451 bool "scsi - Access to SCSI devices"
1454 This provides a 'scsi' command which provides access to SCSI (Small
1455 Computer System Interface) devices. The command provides a way to
1456 scan the bus, reset the bus, read and write data and get information
1460 bool "yaffs2 - Access of YAFFS2 filesystem"
1464 This provides commands for accessing a YAFFS2 filesystem. Yet
1465 Another Flash Filesystem 2 is a filesystem designed specifically
1466 for NAND flash. It incorporates bad-block management and ensures
1467 that device writes are sequential regardless of filesystem
1471 bool "zfs - Access of ZFS filesystem"
1473 This provides commands to accessing a ZFS filesystem, commonly used
1474 on Solaris systems. Two sub-commands are provided:
1476 zfsls - list files in a directory
1477 zfsload - load a file
1479 See doc/README.zfs for more details.
1483 menu "Debug commands"
1488 The bedbug (emBEDded deBUGger) command provides debugging features
1489 for some PowerPC processors. For details please see the
1490 docuemntation in doc/README.beddbug
1493 bool "diag - Board diagnostics"
1495 This command provides access to board diagnostic tests. These are
1496 called Power-on Self Tests (POST). The command allows listing of
1497 available tests and running either all the tests, or specific tests
1501 bool "irq - Show information about interrupts"
1502 depends on !ARM && !MIPS && !SH
1504 This enables two commands:
1506 interrupts - enable or disable interrupts
1507 irqinfo - print device-specific interrupt information
1510 bool "kgdb - Allow debugging of U-Boot with gdb"
1512 This enables a 'kgdb' command which allows gdb to connect to U-Boot
1513 over a serial link for debugging purposes. This allows
1514 single-stepping, inspecting variables, etc. This is supported only
1515 on PowerPC at present.
1518 bool "log - Generation, control and access to logging"
1520 This provides access to logging features. It allows the output of
1521 log data to be controlled to a limited extent (setting up the default
1522 maximum log level for emitting of records). It also provides access
1523 to a command used for testing the log system.
1526 bool "trace - Support tracing of function calls and timing"
1528 Enables a command to control using of function tracing within
1529 U-Boot. This allows recording of call traces including timing
1530 information. The command can write data to memory for exporting
1531 for analsys (e.g. using bootchart). See doc/README.trace for full
1537 tristate "Enable UBI - Unsorted block images commands"
1541 default y if NAND_SUNXI
1543 UBI is a software layer above MTD layer which admits use of LVM-like
1544 logical volumes on top of MTD devices, hides some complexities of
1545 flash chips like wear and bad blocks and provides some other useful
1546 capabilities. Please, consult the MTD web site for more details
1547 (www.linux-mtd.infradead.org). Activate this option if you want
1548 to use U-Boot UBI commands.
1551 tristate "Enable UBIFS - Unsorted block images filesystem commands"
1555 default y if CMD_UBI
1557 UBIFS is a file system for flash devices which works on top of UBI.
projects / u-boot / blob