git.sur5r.net Git - u-boot/blob - drivers/fpga/zynqpl.c

   1 // SPDX-License-Identifier: GPL-2.0+
   2 /*
   3  * (C) Copyright 2012-2013, Xilinx, Michal Simek
   4  *
   5  * (C) Copyright 2012
   6  * Joe Hershberger <joe.hershberger@ni.com>
   7  */
   8
   9 #include <common.h>
  10 #include <console.h>
  11 #include <asm/io.h>
  12 #include <fs.h>
  13 #include <zynqpl.h>
  14 #include <linux/sizes.h>
  15 #include <asm/arch/hardware.h>
  16 #include <asm/arch/sys_proto.h>
  17
  18 #define DEVCFG_CTRL_PCFG_PROG_B         0x40000000
  19 #define DEVCFG_CTRL_PCFG_AES_EFUSE_MASK 0x00001000
  20 #define DEVCFG_ISR_FATAL_ERROR_MASK     0x00740040
  21 #define DEVCFG_ISR_ERROR_FLAGS_MASK     0x00340840
  22 #define DEVCFG_ISR_RX_FIFO_OV           0x00040000
  23 #define DEVCFG_ISR_DMA_DONE             0x00002000
  24 #define DEVCFG_ISR_PCFG_DONE            0x00000004
  25 #define DEVCFG_STATUS_DMA_CMD_Q_F       0x80000000
  26 #define DEVCFG_STATUS_DMA_CMD_Q_E       0x40000000
  27 #define DEVCFG_STATUS_DMA_DONE_CNT_MASK 0x30000000
  28 #define DEVCFG_STATUS_PCFG_INIT         0x00000010
  29 #define DEVCFG_MCTRL_PCAP_LPBK          0x00000010
  30 #define DEVCFG_MCTRL_RFIFO_FLUSH        0x00000002
  31 #define DEVCFG_MCTRL_WFIFO_FLUSH        0x00000001
  32
  33 #ifndef CONFIG_SYS_FPGA_WAIT
  34 #define CONFIG_SYS_FPGA_WAIT CONFIG_SYS_HZ/100  /* 10 ms */
  35 #endif
  36
  37 #ifndef CONFIG_SYS_FPGA_PROG_TIME
  38 #define CONFIG_SYS_FPGA_PROG_TIME       (CONFIG_SYS_HZ * 4) /* 4 s */
  39 #endif
  40
  41 #define DUMMY_WORD      0xffffffff
  42
  43 /* Xilinx binary format header */
  44 static const u32 bin_format[] = {
  45         DUMMY_WORD, /* Dummy words */
  46         DUMMY_WORD,
  47         DUMMY_WORD,
  48         DUMMY_WORD,
  49         DUMMY_WORD,
  50         DUMMY_WORD,
  51         DUMMY_WORD,
  52         DUMMY_WORD,
  53         0x000000bb, /* Sync word */
  54         0x11220044, /* Sync word */
  55         DUMMY_WORD,
  56         DUMMY_WORD,
  57         0xaa995566, /* Sync word */
  58 };
  59
  60 #define SWAP_NO         1
  61 #define SWAP_DONE       2
  62
  63 /*
  64  * Load the whole word from unaligned buffer
  65  * Keep in your mind that it is byte loading on little-endian system
  66  */
  67 static u32 load_word(const void *buf, u32 swap)
  68 {
  69         u32 word = 0;
  70         u8 *bitc = (u8 *)buf;
  71         int p;
  72
  73         if (swap == SWAP_NO) {
  74                 for (p = 0; p < 4; p++) {
  75                         word <<= 8;
  76                         word |= bitc[p];
  77                 }
  78         } else {
  79                 for (p = 3; p >= 0; p--) {
  80                         word <<= 8;
  81                         word |= bitc[p];
  82                 }
  83         }
  84
  85         return word;
  86 }
  87
  88 static u32 check_header(const void *buf)
  89 {
  90         u32 i, pattern;
  91         int swap = SWAP_NO;
  92         u32 *test = (u32 *)buf;
  93
  94         debug("%s: Let's check bitstream header\n", __func__);
  95
  96         /* Checking that passing bin is not a bitstream */
  97         for (i = 0; i < ARRAY_SIZE(bin_format); i++) {
  98                 pattern = load_word(&test[i], swap);
  99
 100                 /*
 101                  * Bitstreams in binary format are swapped
 102                  * compare to regular bistream.
 103                  * Do not swap dummy word but if swap is done assume
 104                  * that parsing buffer is binary format
 105                  */
 106                 if ((__swab32(pattern) != DUMMY_WORD) &&
 107                     (__swab32(pattern) == bin_format[i])) {
 108                         pattern = __swab32(pattern);
 109                         swap = SWAP_DONE;
 110                         debug("%s: data swapped - let's swap\n", __func__);
 111                 }
 112
 113                 debug("%s: %d/%x: pattern %x/%x bin_format\n", __func__, i,
 114                       (u32)&test[i], pattern, bin_format[i]);
 115                 if (pattern != bin_format[i]) {
 116                         debug("%s: Bitstream is not recognized\n", __func__);
 117                         return 0;
 118                 }
 119         }
 120         debug("%s: Found bitstream header at %x %s swapinng\n", __func__,
 121               (u32)buf, swap == SWAP_NO ? "without" : "with");
 122
 123         return swap;
 124 }
 125
 126 static void *check_data(u8 *buf, size_t bsize, u32 *swap)
 127 {
 128         u32 word, p = 0; /* possition */
 129
 130         /* Because buf doesn't need to be aligned let's read it by chars */
 131         for (p = 0; p < bsize; p++) {
 132                 word = load_word(&buf[p], SWAP_NO);
 133                 debug("%s: word %x %x/%x\n", __func__, word, p, (u32)&buf[p]);
 134
 135                 /* Find the first bitstream dummy word */
 136                 if (word == DUMMY_WORD) {
 137                         debug("%s: Found dummy word at position %x/%x\n",
 138                               __func__, p, (u32)&buf[p]);
 139                         *swap = check_header(&buf[p]);
 140                         if (*swap) {
 141                                 /* FIXME add full bitstream checking here */
 142                                 return &buf[p];
 143                         }
 144                 }
 145                 /* Loop can be huge - support CTRL + C */
 146                 if (ctrlc())
 147                         return NULL;
 148         }
 149         return NULL;
 150 }
 151
 152 static int zynq_dma_transfer(u32 srcbuf, u32 srclen, u32 dstbuf, u32 dstlen)
 153 {
 154         unsigned long ts;
 155         u32 isr_status;
 156
 157         /* Set up the transfer */
 158         writel((u32)srcbuf, &devcfg_base->dma_src_addr);
 159         writel(dstbuf, &devcfg_base->dma_dst_addr);
 160         writel(srclen, &devcfg_base->dma_src_len);
 161         writel(dstlen, &devcfg_base->dma_dst_len);
 162
 163         isr_status = readl(&devcfg_base->int_sts);
 164
 165         /* Polling the PCAP_INIT status for Set */
 166         ts = get_timer(0);
 167         while (!(isr_status & DEVCFG_ISR_DMA_DONE)) {
 168                 if (isr_status & DEVCFG_ISR_ERROR_FLAGS_MASK) {
 169                         debug("%s: Error: isr = 0x%08X\n", __func__,
 170                               isr_status);
 171                         debug("%s: Write count = 0x%08X\n", __func__,
 172                               readl(&devcfg_base->write_count));
 173                         debug("%s: Read count = 0x%08X\n", __func__,
 174                               readl(&devcfg_base->read_count));
 175
 176                         return FPGA_FAIL;
 177                 }
 178                 if (get_timer(ts) > CONFIG_SYS_FPGA_PROG_TIME) {
 179                         printf("%s: Timeout wait for DMA to complete\n",
 180                                __func__);
 181                         return FPGA_FAIL;
 182                 }
 183                 isr_status = readl(&devcfg_base->int_sts);
 184         }
 185
 186         debug("%s: DMA transfer is done\n", __func__);
 187
 188         /* Clear out the DMA status */
 189         writel(DEVCFG_ISR_DMA_DONE, &devcfg_base->int_sts);
 190
 191         return FPGA_SUCCESS;
 192 }
 193
 194 static int zynq_dma_xfer_init(bitstream_type bstype)
 195 {
 196         u32 status, control, isr_status;
 197         unsigned long ts;
 198
 199         /* Clear loopback bit */
 200         clrbits_le32(&devcfg_base->mctrl, DEVCFG_MCTRL_PCAP_LPBK);
 201
 202         if (bstype != BIT_PARTIAL) {
 203                 zynq_slcr_devcfg_disable();
 204
 205                 /* Setting PCFG_PROG_B signal to high */
 206                 control = readl(&devcfg_base->ctrl);
 207                 writel(control | DEVCFG_CTRL_PCFG_PROG_B, &devcfg_base->ctrl);
 208
 209                 /*
 210                  * Delay is required if AES efuse is selected as
 211                  * key source.
 212                  */
 213                 if (control & DEVCFG_CTRL_PCFG_AES_EFUSE_MASK)
 214                         mdelay(5);
 215
 216                 /* Setting PCFG_PROG_B signal to low */
 217                 writel(control & ~DEVCFG_CTRL_PCFG_PROG_B, &devcfg_base->ctrl);
 218
 219                 /*
 220                  * Delay is required if AES efuse is selected as
 221                  * key source.
 222                  */
 223                 if (control & DEVCFG_CTRL_PCFG_AES_EFUSE_MASK)
 224                         mdelay(5);
 225
 226                 /* Polling the PCAP_INIT status for Reset */
 227                 ts = get_timer(0);
 228                 while (readl(&devcfg_base->status) & DEVCFG_STATUS_PCFG_INIT) {
 229                         if (get_timer(ts) > CONFIG_SYS_FPGA_WAIT) {
 230                                 printf("%s: Timeout wait for INIT to clear\n",
 231                                        __func__);
 232                                 return FPGA_FAIL;
 233                         }
 234                 }
 235
 236                 /* Setting PCFG_PROG_B signal to high */
 237                 writel(control | DEVCFG_CTRL_PCFG_PROG_B, &devcfg_base->ctrl);
 238
 239                 /* Polling the PCAP_INIT status for Set */
 240                 ts = get_timer(0);
 241                 while (!(readl(&devcfg_base->status) &
 242                         DEVCFG_STATUS_PCFG_INIT)) {
 243                         if (get_timer(ts) > CONFIG_SYS_FPGA_WAIT) {
 244                                 printf("%s: Timeout wait for INIT to set\n",
 245                                        __func__);
 246                                 return FPGA_FAIL;
 247                         }
 248                 }
 249         }
 250
 251         isr_status = readl(&devcfg_base->int_sts);
 252
 253         /* Clear it all, so if Boot ROM comes back, it can proceed */
 254         writel(0xFFFFFFFF, &devcfg_base->int_sts);
 255
 256         if (isr_status & DEVCFG_ISR_FATAL_ERROR_MASK) {
 257                 debug("%s: Fatal errors in PCAP 0x%X\n", __func__, isr_status);
 258
 259                 /* If RX FIFO overflow, need to flush RX FIFO first */
 260                 if (isr_status & DEVCFG_ISR_RX_FIFO_OV) {
 261                         writel(DEVCFG_MCTRL_RFIFO_FLUSH, &devcfg_base->mctrl);
 262                         writel(0xFFFFFFFF, &devcfg_base->int_sts);
 263                 }
 264                 return FPGA_FAIL;
 265         }
 266
 267         status = readl(&devcfg_base->status);
 268
 269         debug("%s: Status = 0x%08X\n", __func__, status);
 270
 271         if (status & DEVCFG_STATUS_DMA_CMD_Q_F) {
 272                 debug("%s: Error: device busy\n", __func__);
 273                 return FPGA_FAIL;
 274         }
 275
 276         debug("%s: Device ready\n", __func__);
 277
 278         if (!(status & DEVCFG_STATUS_DMA_CMD_Q_E)) {
 279                 if (!(readl(&devcfg_base->int_sts) & DEVCFG_ISR_DMA_DONE)) {
 280                         /* Error state, transfer cannot occur */
 281                         debug("%s: ISR indicates error\n", __func__);
 282                         return FPGA_FAIL;
 283                 } else {
 284                         /* Clear out the status */
 285                         writel(DEVCFG_ISR_DMA_DONE, &devcfg_base->int_sts);
 286                 }
 287         }
 288
 289         if (status & DEVCFG_STATUS_DMA_DONE_CNT_MASK) {
 290                 /* Clear the count of completed DMA transfers */
 291                 writel(DEVCFG_STATUS_DMA_DONE_CNT_MASK, &devcfg_base->status);
 292         }
 293
 294         return FPGA_SUCCESS;
 295 }
 296
 297 static u32 *zynq_align_dma_buffer(u32 *buf, u32 len, u32 swap)
 298 {
 299         u32 *new_buf;
 300         u32 i;
 301
 302         if ((u32)buf != ALIGN((u32)buf, ARCH_DMA_MINALIGN)) {
 303                 new_buf = (u32 *)ALIGN((u32)buf, ARCH_DMA_MINALIGN);
 304
 305                 /*
 306                  * This might be dangerous but permits to flash if
 307                  * ARCH_DMA_MINALIGN is greater than header size
 308                  */
 309                 if (new_buf > buf) {
 310                         debug("%s: Aligned buffer is after buffer start\n",
 311                               __func__);
 312                         new_buf -= ARCH_DMA_MINALIGN;
 313                 }
 314                 printf("%s: Align buffer at %x to %x(swap %d)\n", __func__,
 315                        (u32)buf, (u32)new_buf, swap);
 316
 317                 for (i = 0; i < (len/4); i++)
 318                         new_buf[i] = load_word(&buf[i], swap);
 319
 320                 buf = new_buf;
 321         } else if (swap != SWAP_DONE) {
 322                 /* For bitstream which are aligned */
 323                 u32 *new_buf = (u32 *)buf;
 324
 325                 printf("%s: Bitstream is not swapped(%d) - swap it\n", __func__,
 326                        swap);
 327
 328                 for (i = 0; i < (len/4); i++)
 329                         new_buf[i] = load_word(&buf[i], swap);
 330         }
 331
 332         return buf;
 333 }
 334
 335 static int zynq_validate_bitstream(xilinx_desc *desc, const void *buf,
 336                                    size_t bsize, u32 blocksize, u32 *swap,
 337                                    bitstream_type *bstype)
 338 {
 339         u32 *buf_start;
 340         u32 diff;
 341
 342         buf_start = check_data((u8 *)buf, blocksize, swap);
 343
 344         if (!buf_start)
 345                 return FPGA_FAIL;
 346
 347         /* Check if data is postpone from start */
 348         diff = (u32)buf_start - (u32)buf;
 349         if (diff) {
 350                 printf("%s: Bitstream is not validated yet (diff %x)\n",
 351                        __func__, diff);
 352                 return FPGA_FAIL;
 353         }
 354
 355         if ((u32)buf < SZ_1M) {
 356                 printf("%s: Bitstream has to be placed up to 1MB (%x)\n",
 357                        __func__, (u32)buf);
 358                 return FPGA_FAIL;
 359         }
 360
 361         if (zynq_dma_xfer_init(*bstype))
 362                 return FPGA_FAIL;
 363
 364         return 0;
 365 }
 366
 367 static int zynq_load(xilinx_desc *desc, const void *buf, size_t bsize,
 368                      bitstream_type bstype)
 369 {
 370         unsigned long ts; /* Timestamp */
 371         u32 isr_status, swap;
 372
 373         /*
 374          * send bsize inplace of blocksize as it was not a bitstream
 375          * in chunks
 376          */
 377         if (zynq_validate_bitstream(desc, buf, bsize, bsize, &swap,
 378                                     &bstype))
 379                 return FPGA_FAIL;
 380
 381         buf = zynq_align_dma_buffer((u32 *)buf, bsize, swap);
 382
 383         debug("%s: Source = 0x%08X\n", __func__, (u32)buf);
 384         debug("%s: Size = %zu\n", __func__, bsize);
 385
 386         /* flush(clean & invalidate) d-cache range buf */
 387         flush_dcache_range((u32)buf, (u32)buf +
 388                            roundup(bsize, ARCH_DMA_MINALIGN));
 389
 390         if (zynq_dma_transfer((u32)buf | 1, bsize >> 2, 0xffffffff, 0))
 391                 return FPGA_FAIL;
 392
 393         isr_status = readl(&devcfg_base->int_sts);
 394         /* Check FPGA configuration completion */
 395         ts = get_timer(0);
 396         while (!(isr_status & DEVCFG_ISR_PCFG_DONE)) {
 397                 if (get_timer(ts) > CONFIG_SYS_FPGA_WAIT) {
 398                         printf("%s: Timeout wait for FPGA to config\n",
 399                                __func__);
 400                         return FPGA_FAIL;
 401                 }
 402                 isr_status = readl(&devcfg_base->int_sts);
 403         }
 404
 405         debug("%s: FPGA config done\n", __func__);
 406
 407         if (bstype != BIT_PARTIAL)
 408                 zynq_slcr_devcfg_enable();
 409
 410         return FPGA_SUCCESS;
 411 }
 412
 413 #if defined(CONFIG_CMD_FPGA_LOADFS)
 414 static int zynq_loadfs(xilinx_desc *desc, const void *buf, size_t bsize,
 415                        fpga_fs_info *fsinfo)
 416 {
 417         unsigned long ts; /* Timestamp */
 418         u32 isr_status, swap;
 419         u32 partialbit = 0;
 420         loff_t blocksize, actread;
 421         loff_t pos = 0;
 422         int fstype;
 423         char *interface, *dev_part, *filename;
 424
 425         blocksize = fsinfo->blocksize;
 426         interface = fsinfo->interface;
 427         dev_part = fsinfo->dev_part;
 428         filename = fsinfo->filename;
 429         fstype = fsinfo->fstype;
 430
 431         if (fs_set_blk_dev(interface, dev_part, fstype))
 432                 return FPGA_FAIL;
 433
 434         if (fs_read(filename, (u32) buf, pos, blocksize, &actread) < 0)
 435                 return FPGA_FAIL;
 436
 437         if (zynq_validate_bitstream(desc, buf, bsize, blocksize, &swap,
 438                                     &partialbit))
 439                 return FPGA_FAIL;
 440
 441         dcache_disable();
 442
 443         do {
 444                 buf = zynq_align_dma_buffer((u32 *)buf, blocksize, swap);
 445
 446                 if (zynq_dma_transfer((u32)buf | 1, blocksize >> 2,
 447                                       0xffffffff, 0))
 448                         return FPGA_FAIL;
 449
 450                 bsize -= blocksize;
 451                 pos   += blocksize;
 452
 453                 if (fs_set_blk_dev(interface, dev_part, fstype))
 454                         return FPGA_FAIL;
 455
 456                 if (bsize > blocksize) {
 457                         if (fs_read(filename, (u32) buf, pos, blocksize, &actread) < 0)
 458                                 return FPGA_FAIL;
 459                 } else {
 460                         if (fs_read(filename, (u32) buf, pos, bsize, &actread) < 0)
 461                                 return FPGA_FAIL;
 462                 }
 463         } while (bsize > blocksize);
 464
 465         buf = zynq_align_dma_buffer((u32 *)buf, blocksize, swap);
 466
 467         if (zynq_dma_transfer((u32)buf | 1, bsize >> 2, 0xffffffff, 0))
 468                 return FPGA_FAIL;
 469
 470         dcache_enable();
 471
 472         isr_status = readl(&devcfg_base->int_sts);
 473
 474         /* Check FPGA configuration completion */
 475         ts = get_timer(0);
 476         while (!(isr_status & DEVCFG_ISR_PCFG_DONE)) {
 477                 if (get_timer(ts) > CONFIG_SYS_FPGA_WAIT) {
 478                         printf("%s: Timeout wait for FPGA to config\n",
 479                                __func__);
 480                         return FPGA_FAIL;
 481                 }
 482                 isr_status = readl(&devcfg_base->int_sts);
 483         }
 484
 485         debug("%s: FPGA config done\n", __func__);
 486
 487         if (!partialbit)
 488                 zynq_slcr_devcfg_enable();
 489
 490         return FPGA_SUCCESS;
 491 }
 492 #endif
 493
 494 struct xilinx_fpga_op zynq_op = {
 495         .load = zynq_load,
 496 #if defined(CONFIG_CMD_FPGA_LOADFS)
 497         .loadfs = zynq_loadfs,
 498 #endif
 499 };