3 bool "Bit-banged ethernet MII management channel support"
5 config MV88E6352_SWITCH
6 bool "Marvell 88E6352 switch support"
9 bool "Ethernet PHY (physical media interface) support"
11 Enable Ethernet PHY (physical media interface) support.
16 bool "Broadcom BCM53xx (RoboSwitch) Ethernet switch PHY support."
18 Enable support for Broadcom BCM53xx (RoboSwitch) Ethernet switches.
19 This currently supports BCM53125 and similar models.
28 hex "Bitmask of PHY ports"
32 config MV88E61XX_SWITCH
33 bool "Marvel MV88E61xx Ethernet switch PHY support."
37 config MV88E61XX_CPU_PORT
40 config MV88E61XX_PHY_PORTS
41 hex "Bitmask of PHY Ports"
43 config MV88E61XX_FIXED_PORTS
44 hex "Bitmask of PHYless serdes Ports"
46 endif # MV88E61XX_SWITCH
49 bool "Generic 10G PHY support"
52 bool "Aquantia Ethernet PHYs support"
55 bool "Atheros Ethernet PHYs support"
58 bool "Broadcom Ethernet PHYs support"
61 bool "Cortina Ethernet PHYs support"
64 bool "Davicom Ethernet PHYs support"
67 bool "LSI TruePHY ET1011C support"
70 bool "LXT971 Ethernet PHY support"
73 bool "Marvell Ethernet PHYs support"
76 bool "Amlogic Meson GXL Internal PHY support"
79 bool "Micrel Ethernet PHYs support"
81 Enable support for the GbE PHYs manufactured by Micrel (now
82 a part of Microchip). This includes drivers for the KSZ804,
83 KSZ8031, KSZ8051, KSZ8081, KSZ8895, KSZ886x, KSZ8721
84 either/or KSZ9021 (see the "Micrel KSZ9021 family support"
85 config option for details), and KSZ9031 (if configured).
89 config PHY_MICREL_KSZ9021
92 select PHY_MICREL_KSZ90X1
94 config PHY_MICREL_KSZ9031
97 select PHY_MICREL_KSZ90X1
99 config PHY_MICREL_KSZ90X1
100 bool "Micrel KSZ90x1 family support"
103 Enable support for the Micrel KSZ9021 and KSZ9031 GbE PHYs. If
104 enabled, the extended register read/write for KSZ90x1 PHYs
105 is supported through the 'mdio' command and any RGMII signal
106 delays configured in the device tree will be applied to the
107 PHY during initialization.
109 This should not be enabled at the same time with PHY_MICREL_KSZ8XXX
110 as the KSZ9021 and KS8721 share the same ID.
112 config PHY_MICREL_KSZ8XXX
113 bool "Micrel KSZ8xxx family support"
114 default y if !PHY_MICREL_KSZ90X1
116 Enable support for the 8000 series GbE PHYs manufactured by Micrel
117 (now a part of Microchip). This includes drivers for the KSZ804,
118 KSZ8031, KSZ8051, KSZ8081, KSZ8895, KSZ886x, and KSZ8721.
120 This should not be enabled at the same time with PHY_MICREL_KSZ90X1
121 as the KSZ9021 and KS8721 share the same ID.
126 bool "Microsemi Corp Ethernet PHYs support"
129 bool "National Semiconductor Ethernet PHYs support"
132 bool "Realtek Ethernet PHYs support"
134 config RTL8211X_PHY_FORCE_MASTER
135 bool "Ethernet PHY RTL8211x: force 1000BASE-T master mode"
136 depends on PHY_REALTEK
138 Force master mode for 1000BASE-T on RTl8211x PHYs (except for RTL8211F).
139 This can work around link stability and data corruption issues on gigabit
140 links which can occur in slave mode on certain PHYs, e.g. on the
143 Please note that two directly connected devices (i.e. via crossover cable)
144 will not be able to establish a link between each other if they both force
145 master mode. Multiple devices forcing master mode when connected by a
146 network switch do not pose a problem as the switch configures its affected
147 ports into slave mode.
149 This option only affects gigabit links. If you must establish a direct
150 connection between two devices which both force master mode, try forcing
151 the link speed to 100MBit/s.
156 bool "Microchip(SMSC) Ethernet PHYs support"
158 config PHY_TERANETICS
159 bool "Teranetics Ethernet PHYs support"
162 bool "Texas Instruments Ethernet PHYs support"
165 bool "Vitesse Ethernet PHYs support"
168 bool "Xilinx Ethernet PHYs support"
171 bool "Fixed-Link PHY"
174 Fixed PHY is used for having a 'fixed-link' to another MAC with a direct
175 connection (MII, RGMII, ...).
176 There is nothing like autoneogation and so
177 on, the link is always up with fixed speed and fixed duplex-setting.
178 More information: doc/device-tree-bindings/net/fixed-link.txt