2 * Configuation settings for the esd TASREG board.
5 * Stefan Roese, esd gmbh germany, stefan.roese@esd-electronics.com
7 * SPDX-License-Identifier: GPL-2.0+
11 * board/config.h - configuration options, board specific
18 * High Level Configuration Options
23 #define CONFIG_MCFUART
24 #define CONFIG_SYS_UART_PORT (0)
25 #define CONFIG_BAUDRATE 115200
27 #undef CONFIG_WATCHDOG
29 #undef CONFIG_MONITOR_IS_IN_RAM /* no pre-loader required!!! ;-) */
34 #undef CONFIG_BOOTP_BOOTFILESIZE
35 #undef CONFIG_BOOTP_BOOTPATH
36 #undef CONFIG_BOOTP_GATEWAY
37 #undef CONFIG_BOOTP_HOSTNAME
40 * Command line configuration.
42 #define CONFIG_CMD_CACHE
44 #define CONFIG_SYS_LONGHELP /* undef to save memory */
46 #if defined(CONFIG_CMD_KGDB)
47 #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
49 #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
51 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
52 #define CONFIG_SYS_MAXARGS 16 /* max number of command args */
53 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
55 #define CONFIG_SYS_DEVICE_NULLDEV 1 /* include nulldev device */
56 #define CONFIG_SYS_CONSOLE_INFO_QUIET 1 /* don't print console @ startup */
57 #define CONFIG_AUTO_COMPLETE 1 /* add autocompletion support */
58 #define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */
60 #define CONFIG_SYS_LOAD_ADDR 0x200000 /* default load address */
62 #define CONFIG_SYS_MEMTEST_START 0x400
63 #define CONFIG_SYS_MEMTEST_END 0x380000
66 * Clock configuration: enable only one of the following options
69 #undef CONFIG_SYS_PLL_BYPASS /* bypass PLL for test purpose */
70 #define CONFIG_SYS_FAST_CLK 1 /* MCF5249 can run at 140MHz */
71 #define CONFIG_SYS_CLK 132025600 /* MCF5249 can run at 140MHz */
74 * Low Level Configuration Settings
75 * (address mappings, register initial values, etc.)
76 * You should know what you are doing if you make changes here.
79 #define CONFIG_SYS_MBAR 0x10000000 /* Register Base Addrs */
80 #define CONFIG_SYS_MBAR2 0x80000000
82 /*-----------------------------------------------------------------------
83 * Definitions for initial stack pointer and data area (in DPRAM)
85 #define CONFIG_SYS_INIT_RAM_ADDR 0x20000000
86 #define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* Size of used area in internal SRAM */
87 #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
88 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
90 #define CONFIG_ENV_IS_IN_FLASH 1
92 #define LDS_BOARD_TEXT \
93 . = DEFINED(env_offset) ? env_offset : .; \
94 common/env_embedded.o (.text);
96 #define CONFIG_ENV_OFFSET 0x4000 /* Address of Environment Sector*/
97 #define CONFIG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */
98 #define CONFIG_ENV_SECT_SIZE 0x2000 /* see README - env sector total size */
100 /*-----------------------------------------------------------------------
101 * Start addresses for the final memory configuration
102 * (Set up by the startup code)
103 * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
105 #define CONFIG_SYS_SDRAM_BASE 0x00000000
106 #define CONFIG_SYS_SDRAM_SIZE 16 /* SDRAM size in MB */
107 #define CONFIG_SYS_FLASH_BASE (CONFIG_SYS_CS0_BASE)
109 #if 0 /* test-only */
110 #define CONFIG_PRAM 512 /* test-only for SDRAM problem!!!!!!!!!!!!!!!!!!!! */
113 #define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_FLASH_BASE + 0x400)
115 #define CONFIG_SYS_MONITOR_LEN 0x20000
116 #define CONFIG_SYS_MALLOC_LEN (1 * 1024*1024) /* Reserve 1 MB for malloc() */
117 #define CONFIG_SYS_BOOTPARAMS_LEN 64*1024
120 * For booting Linux, the board info and command line data
121 * have to be in the first 8 MB of memory, since this is
122 * the maximum mapped by the Linux kernel during initialization ??
124 #define CONFIG_SYS_BOOTMAPSZ (CONFIG_SYS_SDRAM_BASE + (CONFIG_SYS_SDRAM_SIZE << 20))
126 /*-----------------------------------------------------------------------
129 #define CONFIG_SYS_FLASH_CFI
130 #ifdef CONFIG_SYS_FLASH_CFI
132 # define CONFIG_FLASH_CFI_DRIVER 1
133 # define CONFIG_SYS_FLASH_SIZE 0x1000000 /* Max size that the board might have */
134 # define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT
135 # define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
136 # define CONFIG_SYS_MAX_FLASH_SECT 137 /* max number of sectors on one chip */
137 # define CONFIG_SYS_FLASH_PROTECTION /* "Real" (hardware) sectors protection */
138 # define CONFIG_SYS_FLASH_CHECKSUM
139 # define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE }
142 /*-----------------------------------------------------------------------
143 * Cache Configuration
145 #define CONFIG_SYS_CACHELINE_SIZE 16
147 #define ICACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \
148 CONFIG_SYS_INIT_RAM_SIZE - 8)
149 #define DCACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \
150 CONFIG_SYS_INIT_RAM_SIZE - 4)
151 #define CONFIG_SYS_ICACHE_INV (CF_CACR_DCM)
152 #define CONFIG_SYS_CACHE_ACR0 (CONFIG_SYS_FLASH_BASE | \
154 CF_ACR_EN | CF_ACR_SM_ALL)
155 #define CONFIG_SYS_CACHE_ACR1 (CONFIG_SYS_SDRAM_BASE | \
156 CF_ADDRMASK(CONFIG_SYS_SDRAM_SIZE) | \
157 CF_ACR_EN | CF_ACR_SM_ALL)
158 #define CONFIG_SYS_CACHE_ICACR (CF_CACR_CENB | CF_CACR_CEIB | \
161 /*-----------------------------------------------------------------------
162 * Memory bank definitions
165 /* CS0 - AMD Flash, address 0xffc00000 */
166 #define CONFIG_SYS_CS0_BASE 0xffe00000
167 #define CONFIG_SYS_CS0_CTRL 0x00001980 /* WS=0110, AA=1, PS=10 */
168 /** Note: There is a CSMR0/DRAM vector problem, need to disable C/I ***/
169 #define CONFIG_SYS_CS0_MASK 0x003f0021 /* 4MB, AA=0, WP=0, C/I=1, V=1 */
171 /* CS1 - FPGA, address 0xe0000000 */
172 #define CONFIG_SYS_CS1_BASE 0xe0000000
173 #define CONFIG_SYS_CS1_CTRL 0x00000d80 /* WS=0011, AA=1, PS=10 */
174 #define CONFIG_SYS_CS1_MASK 0x00010001 /* 128kB, AA=0, WP=0, C/I=0, V=1*/
176 /*-----------------------------------------------------------------------
179 #define CONFIG_SYS_GPIO_FUNC 0x00000008 /* Set gpio pins: none */
180 #define CONFIG_SYS_GPIO1_FUNC 0x00df00f0 /* 36-39(SWITCH),48-52(FPGAs),54*/
181 #define CONFIG_SYS_GPIO_EN 0x00000008 /* Set gpio output enable */
182 #define CONFIG_SYS_GPIO1_EN 0x00c70000 /* Set gpio output enable */
183 #define CONFIG_SYS_GPIO_OUT 0x00000008 /* Set outputs to default state */
184 #define CONFIG_SYS_GPIO1_OUT 0x00c70000 /* Set outputs to default state */
185 #define CONFIG_SYS_GPIO1_LED 0x00400000 /* user led */