2 * Copyright 2004, 2011 Freescale Semiconductor.
3 * (C) Copyright 2002,2003 Motorola,Inc.
4 * Xianghua Xiao <X.Xiao@motorola.com>
6 * SPDX-License-Identifier: GPL-2.0+
10 * mpc8560ads board configuration file
12 * Please refer to doc/README.mpc85xx for more info.
14 * Make sure you change the MAC address and other network params first,
15 * search for CONFIG_SERVERIP, etc. in this file.
21 /* High Level Configuration Options */
22 #define CONFIG_BOOKE 1 /* BOOKE */
23 #define CONFIG_E500 1 /* BOOKE e500 family */
24 #define CONFIG_CPM2 1 /* has CPM2 */
25 #define CONFIG_MPC8560ADS 1 /* MPC8560ADS board specific */
26 #define CONFIG_MPC8560 1
29 * default CCARBAR is at 0xff700000
30 * assume U-Boot is less than 0.5MB
32 #define CONFIG_SYS_TEXT_BASE 0xfff80000
34 #define CONFIG_PCI_INDIRECT_BRIDGE
35 #define CONFIG_SYS_PCI_64BIT 1 /* enable 64-bit PCI resources */
36 #define CONFIG_TSEC_ENET /* tsec ethernet support */
37 #undef CONFIG_ETHER_ON_FCC /* cpm FCC ethernet support */
38 #define CONFIG_ENV_OVERWRITE
39 #define CONFIG_FSL_LAW 1 /* Use common FSL init code */
40 #define CONFIG_RESET_PHY_R 1 /* Call reset_phy() */
45 * Two valid values are:
49 * Most PCI cards are still 33Mhz, so in the presence of PCI, 33MHz
50 * is likely the desired value here, so that is now the default.
51 * The board, however, can run at 66MHz. In any event, this value
52 * must match the settings of some switches. Details can be found
53 * in the README.mpc85xxads.
56 #ifndef CONFIG_SYS_CLK_FREQ
57 #define CONFIG_SYS_CLK_FREQ 33000000
61 * These can be toggled for performance analysis, otherwise use default.
63 #define CONFIG_L2_CACHE /* toggle L2 cache */
64 #define CONFIG_BTB /* toggle branch predition */
66 #define CONFIG_SYS_INIT_DBCR DBCR_IDM /* Enable Debug Exceptions */
68 #define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest region */
69 #define CONFIG_SYS_MEMTEST_END 0x00400000
71 #define CONFIG_SYS_CCSRBAR 0xe0000000
72 #define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR
75 #define CONFIG_SYS_FSL_DDR1
76 #define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup*/
77 #define CONFIG_DDR_SPD
78 #undef CONFIG_FSL_DDR_INTERACTIVE
80 #define CONFIG_MEM_INIT_VALUE 0xDeadBeef
82 #define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/
83 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
85 #define CONFIG_NUM_DDR_CONTROLLERS 1
86 #define CONFIG_DIMM_SLOTS_PER_CTLR 1
87 #define CONFIG_CHIP_SELECTS_PER_CTRL (2 * CONFIG_DIMM_SLOTS_PER_CTLR)
89 /* I2C addresses of SPD EEPROMs */
90 #define SPD_EEPROM_ADDRESS 0x51 /* CTLR 0 DIMM 0 */
92 /* These are used when DDR doesn't use SPD. */
93 #define CONFIG_SYS_SDRAM_SIZE 128 /* DDR is 128MB */
94 #define CONFIG_SYS_DDR_CS0_BNDS 0x00000007 /* 0-128MB */
95 #define CONFIG_SYS_DDR_CS0_CONFIG 0x80000002
96 #define CONFIG_SYS_DDR_TIMING_1 0x37344321
97 #define CONFIG_SYS_DDR_TIMING_2 0x00000800 /* P9-45,may need tuning */
98 #define CONFIG_SYS_DDR_CONTROL 0xc2000000 /* unbuffered,no DYN_PWR */
99 #define CONFIG_SYS_DDR_MODE 0x00000062 /* DLL,normal,seq,4/2.5 */
100 #define CONFIG_SYS_DDR_INTERVAL 0x05200100 /* autocharge,no open page */
103 * SDRAM on the Local Bus
105 #define CONFIG_SYS_LBC_SDRAM_BASE 0xf0000000 /* Localbus SDRAM */
106 #define CONFIG_SYS_LBC_SDRAM_SIZE 64 /* LBC SDRAM is 64MB */
108 #define CONFIG_SYS_FLASH_BASE 0xff000000 /* start of FLASH 16M */
109 #define CONFIG_SYS_BR0_PRELIM 0xff001801 /* port size 32bit */
111 #define CONFIG_SYS_OR0_PRELIM 0xff006ff7 /* 16MB Flash */
112 #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */
113 #define CONFIG_SYS_MAX_FLASH_SECT 64 /* sectors per device */
114 #undef CONFIG_SYS_FLASH_CHECKSUM
115 #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
116 #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
118 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
120 #if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
121 #define CONFIG_SYS_RAMBOOT
123 #undef CONFIG_SYS_RAMBOOT
126 #define CONFIG_FLASH_CFI_DRIVER
127 #define CONFIG_SYS_FLASH_CFI
128 #define CONFIG_SYS_FLASH_EMPTY_INFO
130 #undef CONFIG_CLOCKS_IN_MHZ
133 * Local Bus Definitions
137 * Base Register 2 and Option Register 2 configure SDRAM.
138 * The SDRAM base address, CONFIG_SYS_LBC_SDRAM_BASE, is 0xf0000000.
141 * Base address of 0xf0000000 = BR[0:16] = 1111 0000 0000 0000 0
142 * port-size = 32-bits = BR2[19:20] = 11
143 * no parity checking = BR2[21:22] = 00
144 * SDRAM for MSEL = BR2[24:26] = 011
147 * 0 4 8 12 16 20 24 28
148 * 1111 0000 0000 0000 0001 1000 0110 0001 = f0001861
150 * FIXME: CONFIG_SYS_LBC_SDRAM_BASE should be masked and OR'ed into
151 * FIXME: the top 17 bits of BR2.
154 #define CONFIG_SYS_BR2_PRELIM 0xf0001861
157 * The SDRAM size in MB, CONFIG_SYS_LBC_SDRAM_SIZE, is 64.
160 * 64MB mask for AM, OR2[0:7] = 1111 1100
161 * XAM, OR2[17:18] = 11
162 * 9 columns OR2[19-21] = 010
163 * 13 rows OR2[23-25] = 100
164 * EAD set for extra time OR[31] = 1
166 * 0 4 8 12 16 20 24 28
167 * 1111 1100 0000 0000 0110 1001 0000 0001 = fc006901
170 #define CONFIG_SYS_OR2_PRELIM 0xfc006901
172 #define CONFIG_SYS_LBC_LCRR 0x00030004 /* LB clock ratio reg */
173 #define CONFIG_SYS_LBC_LBCR 0x00000000 /* LB config reg */
174 #define CONFIG_SYS_LBC_LSRT 0x20000000 /* LB sdram refresh timer */
175 #define CONFIG_SYS_LBC_MRTPR 0x20000000 /* LB refresh timer prescal*/
177 #define CONFIG_SYS_LBC_LSDMR_COMMON ( LSDMR_BSMA1516 \
188 * SDRAM Controller configuration sequence.
190 #define CONFIG_SYS_LBC_LSDMR_1 (CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_PCHALL)
191 #define CONFIG_SYS_LBC_LSDMR_2 (CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_ARFRSH)
192 #define CONFIG_SYS_LBC_LSDMR_3 (CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_ARFRSH)
193 #define CONFIG_SYS_LBC_LSDMR_4 (CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_MRW)
194 #define CONFIG_SYS_LBC_LSDMR_5 (CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_NORMAL)
197 * 32KB, 8-bit wide for ADS config reg
199 #define CONFIG_SYS_BR4_PRELIM 0xf8000801
200 #define CONFIG_SYS_OR4_PRELIM 0xffffe1f1
201 #define CONFIG_SYS_BCSR (CONFIG_SYS_BR4_PRELIM & 0xffff8000)
203 #define CONFIG_SYS_INIT_RAM_LOCK 1
204 #define CONFIG_SYS_INIT_RAM_ADDR 0xe4010000 /* Initial RAM address */
205 #define CONFIG_SYS_INIT_RAM_SIZE 0x4000 /* Size of used area in RAM */
207 #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
208 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
210 #define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
211 #define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserved for malloc */
214 #define CONFIG_CONS_ON_SCC /* define if console on SCC */
215 #undef CONFIG_CONS_NONE /* define if console on something else */
216 #define CONFIG_CONS_INDEX 1 /* which serial channel for console */
218 #define CONFIG_BAUDRATE 115200
220 #define CONFIG_SYS_BAUDRATE_TABLE \
221 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
226 #define CONFIG_SYS_I2C
227 #define CONFIG_SYS_I2C_FSL
228 #define CONFIG_SYS_FSL_I2C_SPEED 400000
229 #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
230 #define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
231 #define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} }
234 #define CONFIG_SYS_RIO_MEM_VIRT 0xc0000000 /* base address */
235 #define CONFIG_SYS_RIO_MEM_BUS 0xc0000000 /* base address */
236 #define CONFIG_SYS_RIO_MEM_PHYS 0xc0000000
237 #define CONFIG_SYS_RIO_MEM_SIZE 0x20000000 /* 128M */
241 * Memory space is mapped 1-1, but I/O space must start from 0.
243 #define CONFIG_SYS_PCI1_MEM_VIRT 0x80000000
244 #define CONFIG_SYS_PCI1_MEM_BUS 0x80000000
245 #define CONFIG_SYS_PCI1_MEM_PHYS 0x80000000
246 #define CONFIG_SYS_PCI1_MEM_SIZE 0x20000000 /* 512M */
247 #define CONFIG_SYS_PCI1_IO_VIRT 0xe2000000
248 #define CONFIG_SYS_PCI1_IO_BUS 0x00000000
249 #define CONFIG_SYS_PCI1_IO_PHYS 0xe2000000
250 #define CONFIG_SYS_PCI1_IO_SIZE 0x100000 /* 1M */
252 #if defined(CONFIG_PCI)
253 #undef CONFIG_EEPRO100
256 #if !defined(CONFIG_PCI_PNP)
257 #define PCI_ENET0_IOADDR 0xe0000000
258 #define PCI_ENET0_MEMADDR 0xe0000000
259 #define PCI_IDSEL_NUMBER 0x0c /* slot0->3(IDSEL)=12->15 */
262 #undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
263 #define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1057 /* Motorola */
265 #endif /* CONFIG_PCI */
267 #ifdef CONFIG_TSEC_ENET
270 #define CONFIG_MII 1 /* MII PHY management */
272 #define CONFIG_TSEC1 1
273 #define CONFIG_TSEC1_NAME "TSEC0"
274 #define CONFIG_TSEC2 1
275 #define CONFIG_TSEC2_NAME "TSEC1"
276 #define TSEC1_PHY_ADDR 0
277 #define TSEC2_PHY_ADDR 1
278 #define TSEC1_PHYIDX 0
279 #define TSEC2_PHYIDX 0
280 #define TSEC1_FLAGS TSEC_GIGABIT
281 #define TSEC2_FLAGS TSEC_GIGABIT
283 /* Options are: TSEC[0-1] */
284 #define CONFIG_ETHPRIME "TSEC0"
286 #endif /* CONFIG_TSEC_ENET */
288 #ifdef CONFIG_ETHER_ON_FCC /* CPM FCC Ethernet */
290 #undef CONFIG_ETHER_NONE /* define if ether on something else */
291 #define CONFIG_ETHER_INDEX 2 /* which channel for ether */
293 #if (CONFIG_ETHER_INDEX == 2)
297 * - Select bus for bd/buffers
300 #define CONFIG_SYS_CMXFCR_MASK2 (CMXFCR_FC2 | CMXFCR_RF2CS_MSK | CMXFCR_TF2CS_MSK)
301 #define CONFIG_SYS_CMXFCR_VALUE2 (CMXFCR_RF2CS_CLK13 | CMXFCR_TF2CS_CLK14)
302 #define CONFIG_SYS_CPMFCR_RAMTYPE 0
303 #define CONFIG_SYS_FCC_PSMR (FCC_PSMR_FDE)
304 #define FETH2_RST 0x01
305 #elif (CONFIG_ETHER_INDEX == 3)
306 /* need more definitions here for FE3 */
307 #define FETH3_RST 0x80
308 #endif /* CONFIG_ETHER_INDEX */
311 #define CONFIG_MII 1 /* MII PHY management */
314 #define CONFIG_BITBANGMII /* bit-bang MII PHY management */
317 * GPIO pins used for bit-banged MII communications
319 #define MDIO_PORT 2 /* Port C */
320 #define MDIO_DECLARE volatile ioport_t *iop = ioport_addr ( \
321 (immap_t *) CONFIG_SYS_IMMR, MDIO_PORT )
322 #define MDC_DECLARE MDIO_DECLARE
324 #define MDIO_ACTIVE (iop->pdir |= 0x00400000)
325 #define MDIO_TRISTATE (iop->pdir &= ~0x00400000)
326 #define MDIO_READ ((iop->pdat & 0x00400000) != 0)
328 #define MDIO(bit) if(bit) iop->pdat |= 0x00400000; \
329 else iop->pdat &= ~0x00400000
331 #define MDC(bit) if(bit) iop->pdat |= 0x00200000; \
332 else iop->pdat &= ~0x00200000
334 #define MIIDELAY udelay(1)
341 #ifndef CONFIG_SYS_RAMBOOT
342 #define CONFIG_ENV_IS_IN_FLASH 1
343 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + 0x40000)
344 #define CONFIG_ENV_SECT_SIZE 0x40000 /* 256K(one sector) for env */
345 #define CONFIG_ENV_SIZE 0x2000
347 #define CONFIG_SYS_NO_FLASH 1 /* Flash is not usable now */
348 #define CONFIG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */
349 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000)
350 #define CONFIG_ENV_SIZE 0x2000
353 #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
354 #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
359 #define CONFIG_BOOTP_BOOTFILESIZE
360 #define CONFIG_BOOTP_BOOTPATH
361 #define CONFIG_BOOTP_GATEWAY
362 #define CONFIG_BOOTP_HOSTNAME
365 * Command line configuration.
367 #define CONFIG_CMD_IRQ
368 #define CONFIG_CMD_REGINFO
370 #if defined(CONFIG_PCI)
371 #define CONFIG_CMD_PCI
374 #if defined(CONFIG_ETHER_ON_FCC)
377 #undef CONFIG_WATCHDOG /* watchdog disabled */
380 * Miscellaneous configurable options
382 #define CONFIG_SYS_LONGHELP /* undef to save memory */
383 #define CONFIG_CMDLINE_EDITING /* Command-line editing */
384 #define CONFIG_AUTO_COMPLETE /* add autocompletion support */
385 #define CONFIG_SYS_LOAD_ADDR 0x1000000 /* default load address */
387 #if defined(CONFIG_CMD_KGDB)
388 #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
390 #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
393 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
394 #define CONFIG_SYS_MAXARGS 16 /* max number of command args */
395 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
398 * For booting Linux, the board info and command line data
399 * have to be in the first 64 MB of memory, since this is
400 * the maximum mapped by the Linux kernel during initialization.
402 #define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial Memory map for Linux*/
403 #define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */
405 #if defined(CONFIG_CMD_KGDB)
406 #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
410 * Environment Configuration
412 #if defined(CONFIG_TSEC_ENET) || defined(CONFIG_ETHER_ON_FCC)
413 #define CONFIG_HAS_ETH0
414 #define CONFIG_HAS_ETH1
415 #define CONFIG_HAS_ETH2
416 #define CONFIG_HAS_ETH3
419 #define CONFIG_IPADDR 192.168.1.253
421 #define CONFIG_HOSTNAME unknown
422 #define CONFIG_ROOTPATH "/nfsroot"
423 #define CONFIG_BOOTFILE "your.uImage"
425 #define CONFIG_SERVERIP 192.168.1.1
426 #define CONFIG_GATEWAYIP 192.168.1.1
427 #define CONFIG_NETMASK 255.255.255.0
429 #define CONFIG_LOADADDR 200000 /* default location for tftp and bootm */
431 #undef CONFIG_BOOTARGS /* the boot command will set bootargs */
433 #define CONFIG_BAUDRATE 115200
435 #define CONFIG_EXTRA_ENV_SETTINGS \
437 "consoledev=ttyCPM\0" \
438 "ramdiskaddr=1000000\0" \
439 "ramdiskfile=your.ramdisk.u-boot\0" \
441 "fdtfile=mpc8560ads.dtb\0"
443 #define CONFIG_NFSBOOTCOMMAND \
444 "setenv bootargs root=/dev/nfs rw " \
445 "nfsroot=$serverip:$rootpath " \
446 "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
447 "console=$consoledev,$baudrate $othbootargs;" \
448 "tftp $loadaddr $bootfile;" \
449 "tftp $fdtaddr $fdtfile;" \
450 "bootm $loadaddr - $fdtaddr"
452 #define CONFIG_RAMBOOTCOMMAND \
453 "setenv bootargs root=/dev/ram rw " \
454 "console=$consoledev,$baudrate $othbootargs;" \
455 "tftp $ramdiskaddr $ramdiskfile;" \
456 "tftp $loadaddr $bootfile;" \
457 "tftp $fdtaddr $fdtfile;" \
458 "bootm $loadaddr $ramdiskaddr $fdtaddr"
460 #define CONFIG_BOOTCOMMAND CONFIG_NFSBOOTCOMMAND
462 #endif /* __CONFIG_H */